NB7L11M 2.5V/3.3V Differential 1:2 Clock/Data Fanout Buffer/ Translator with CML Outputs and Internal Termination http://onsemi.com MARKING DIAGRAM* Description The NB7L11M is a differential 1−to−2 clock/data distribution chip with internal source termination and CML output structure, optimized for low skew and minimal jitter. The device is functionally equivalent to the EP11, LVEP11, or SG11 devices. Device produces two identical output copies of clock or data operating up to 8 GHz or 12 Gb/s, respectively. As such, NB7L11M is ideal for SONET, GigE, Fiber Channel, Backplane and other clock/data distribution applications. Inputs incorporate internal 50 W termination resistors and accept LVPECL, CML, LVCMOS, LVTTL, or LVDS (See Table 6). Differential 16 mA CML output provides matching internal 50 W terminations, and 400 mV output swings when externally terminated, 50 W to VCC (See Figure 14). The device is offered in a low profile 3x3 mm 16−pin QFN package. Application notes, models, and support documentation are available at www.onsemi.com. Features • • • • • • • • • • • • 16 1 QFN−16 MN SUFFIX CASE 485G A L Y W G NB7L 11M ALYWG G = Assembly Location = Wafer Lot = Year = Work Week = Pb−Free Package (Note: Microdot may be in either location) *For additional marking information, refer to Application Note AND8002/D. Maximum Input Clock Frequency up to 8 GHz Typical Maximum Input Data Rate up to 12 Gb/s Typical < 0.5 ps of RMS Clock Jitter ORDERING INFORMATION < 10 ps of Data Dependent Jitter 30 ps Typical Rise and Fall Times 110 ps Typical Propagation Delay 3 ps Typical Within Device Skew Operating Range: VCC = 2.375 V to 3.465 V with VEE = 0 V CML Output Level (400 mV Peak−to−Peak Output) Differential Output Only 50 W Internal Input and Output Termination Resistors Functionally Compatible with Existing 2.5 V/3.3 V LVEL, LVEP, EP and SG Devices Pb−Free Packages are Available* See detailed ordering and shipping information in the package dimensions section on page 10 of this data sheet. *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. Q0 VTCLK Q0 50 W CLK CLK 50 W VTCLK Q1 Figure 1. Logic Diagram © Semiconductor Components Industries, LLC, 2006 January, 2006 − Rev. 1 Q1 1 Publication Order Number: NB7L11M/D NB7L11M VTCLK 1 CLK 2 VCC Q0 Q0 VCC 16 15 14 13 Exposed Pad (EP) 12 VEE 11 VEE NB7L11M CLK 3 10 VEE VTCLK 4 9 VEE 5 6 7 8 VCC Q1 Q1 VCC Figure 2. QFN−16 Pinout (Top View) Table 1. PIN DESCRIPTION Pin Name I/O 1 VTCLK − Description 2 CLK LVPECL, CML, LVCMOS, LVTTL, LVDS Inverted Differential Clock/Data Input. (Note 1) 3 CLK LVPECL, CML, LVCMOS, LVTTL, LVDS Noninverted Differential Clock/Data Input. (Note 1) 4 VTCLK − Internal 50 W Termination Pin for CLK 5,8,13,16 VCC − Positive Supply Voltage. All VCC pins must be externally connected to a Power Supply to guarantee proper operation. 6 Q1 CML Output Inverted CLK output 1 with internal 50 W source termination resistor. (Note 2) 7 Q1 CML Output Noninverted CLK output 1 with internal 50 W source termination resistor. (Note 2) 9,10,11,12 VEE − 14 Q0 CML Output Inverted CLK output 0 with internal 50 W source termination resistor. (Note 2) 15 Q0 CML Output Noninverted CLK output 0 with internal 50 W source termination resistor. (Note 2) − EP − Internal 50 W Termination Pin for CLK Negative Supply Voltage. All VEE pins must be externally connected to a Power Supply to guarantee proper operation. Exposed Pad. The thermally exposed pad on package bottom (see case drawing) must be attached to a heatsinking conduit. It is recommended to connect the EP to the lower potential (VEE). 1. In the differential configuration when the input termination pins (VTCLK, VTCLK) are connected to a common termination voltage or left open, and if no signal is applied on CLK and CLK then the device will be susceptible to self−oscillation. 2. CML outputs require 50 W receiver termination resistor to VCC for proper operation. http://onsemi.com 2 NB7L11M Table 2. ATTRIBUTES Characteristics ESD Protection Value Human Body Model Machine Model Charged Device Model Moisture Sensitivity (Note 3) QFN−16 Flammability Rating Oxygen Index: 28 to 34 > 1500 V > 50 V > 500 V Pb Pkg Pb−Free Pkg Level 1 Level 1 UL 94 V−0 @ 0.125 in Transistor Count 285 Meets or exceeds JEDEC Spec EIA/JESD78 IC Latchup Test 3. For additional information, see Application Note AND8003/D. Table 3. MAXIMUM RATINGS Symbol Parameter Condition 1 Rating Unit 3.6 V 3.6 V 2.8 |VCC − VEE| V Static Surge 45 80 mA mA Output Current Continuous Surge 25 50 mA mA TA Operating Temperature Range QFN−16 −40 to +85 °C Tstg Storage Temperature Range −65 to +150 °C qJA Thermal Resistance (Junction−to−Ambient) (Note 4) 0 lfpm 500 lfpm QFN−16 QFN−16 42 36 °C/W °C/W qJC Thermal Resistance (Junction−to−Case) 2S2P (Note 4) QFN−16 3 to 4 °C/W Tsol Wave Solder 265 265 °C VCC Positive Power Supply VEE = 0 V VI Input Voltage VEE = 0 V VINPP Differential Input Voltage |CLK − CLK| VCC − VEE w 2.8 V VCC − VEE < 2.8 V IIN Input Current Through RT (50 W Resistor) Iout Pb Pb−Free Condition 2 VEE v VI v VCC Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied, damage may occur and reliability may be affected. 4. JEDEC standard multilayer board − 2S2P (2 signal, 2 power). http://onsemi.com 3 NB7L11M Table 4. DC CHARACTERISTICS, CLOCK Inputs, CML Outputs (VCC = 2.375 V to 3.465 V, VEE = 0 V, TA = −40°C to +85°C) (Note 5) Symbol Characteristic Min Typ Max Unit 85 105 mA ICC Power Supply Current (Input and Outputs open) VOH Output HIGH Voltage (Note 6) VCC − 60 VCC − 20 VCC mV VOL Output LOW Voltage (Note 6) VCC − 530 VCC − 420 VCC − 360 mV Differential Input Driven Single−Ended (see Figures 10 & 12) (Note 8) Vth Input Threshold Reference Voltage Range (Note 7) 1125 VCC − 75 mV VIH Single−ended Input HIGH Voltage (Note 8) Vth + 75 VCC mV VIL Single−ended Input LOW Voltage (Note 8) VEE Vth − 75 mV Differential Inputs Driven Differentially (see Figures 11 & 13) (Note 8) VIHCLK Differential Input HIGH Voltage 1200 VCC mV VILCLK Differential Input LOW Voltage VEE VCC − 75 mV VCMR Input Common Mode Range (Differential Configuration) 1163 VCC – 38 mV VID Differential Input Voltage (VIHCLK − VILCLK) 75 2500 mV IIH Input HIGH Current CLK / CLK (VTCLK/VTCLK Open) 0 25 100 mA IIL Input LOW Current CLK / CLK (VTCLK/VTCLK Open) −10 0 10 mA RTIN Internal Input Termination Resistor 45 50 55 W RTOUT Internal Output Termination Resistor 45 50 55 W RTemp Coef Internal I/O Termination Resistor Temperature Coefficient 6.38 mW/°C NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 5. Input and output parameters vary 1:1 with VCC. 6. CML outputs require 50 W receiver termination resistors to VCC for proper operation. 7. Vth is applied to the complementary input when operating in single−ended mode. 8. VCMR min varies 1:1 with VEE, VCMR max varies 1:1 with VCC. http://onsemi.com 4 NB7L11M Table 5. AC CHARACTERISTICS (VCC = 2.375 V to 3.465 V, VEE = 0 V; Note 9) Characteristic Symbol −40°C Min Typ 400 300 25°C Max VOUTPP Output Voltage Amplitude (@VINPPmin) fin ≤ 6 GHz (See Figure 3) fin ≤ 8 GHz 280 140 fdata Maximum Operating Data Rate 10 12 tPLH, tPHL Propagation Delay to Output Differential 70 110 150 tSKEW Duty Cycle Skew (Note 10) Within−Device Skew Device−to−Device Skew (Note 11) 2.0 3.0 20 tJITTER RMS Random Clock Jitter (Note 12) fin = 6 GHz fin =8 GHz Peak/Peak Data Dependent Jitter fin = 2.488 Gb/s (Note 13) fdata =5 Gb/s fdata =10 Gb/s VINPP Input Voltage Swing/Sensitivity (Differential Configuration) (Note 14) tr tf Output Rise/Fall Times @ 1 GHz Q, Q (20% − 80%) 75 Min Typ 280 140 400 300 Max 10 12 70 110 150 5.0 15 50 2.0 3.0 20 0.2 0.2 2.0 3.0 5.0 0.5 0.5 5.0 8.0 10 400 2500 30 60 75 Unit 85°C Min Typ 280 140 400 300 Max mV 10 12 70 110 150 ps 5.0 15 50 2.0 3.0 20 5.0 15 50 ps 0.2 0.2 2.0 3.0 5.0 0.5 0.5 5.0 8.0 10 0.2 0.2 2.0 3.0 5.0 0.5 0.5 5.0 8.0 10 ps 400 2500 400 2500 mV 30 60 30 60 ps 75 Gb/s NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 9. Measured by forcing VINPP (TYP) from a 50% duty cycle clock source. All loading with an external RL = 50 W to VCC. Input edge rates 40 ps (20% − 80%). 10. Duty cycle skew is measured between differential outputs using the deviations of the sum of Tpw− and Tpw+ @1 GHz. 11. Device to device skew is measured between outputs under identical transition @ 1 GHz. 12. Additive RMS jitter with 50% duty cycle clock signal at 8 GHz & 10 GHz. 13. Additive peak−to−peak data dependent jitter with input NRZ data at PRBS 2^23−1. 14. VINPP (MAX) cannot exceed VCC − VEE. Input voltage swing is a single−ended measurement operating in differential mode. OUTPUT VOLTAGE AMPLITUDE (mV) 500 VCC = 3.3 V 400 VCC = 2.5 V 300 200 100 0 0 1 2 3 4 5 6 7 8 9 10 11 12 INPUT FREQUENCY (GHz) Figure 3. Output Voltage Amplitude (VOUTPP) versus Input Clock Frequency (fin) at Ambient Temperature (Typical) (VINPP = 400 mV) http://onsemi.com 5 Voltage (50 mV/div) Voltage (50 mV/div) NB7L11M DDJ = 1 ps* Time (80.4 ps/div) Time (40 ps/div) Figure 4. Typical Output Waveform at 2.488 Gb/s with PRBS 2^23−1 (Vinpp = 75 mV) Figure 5. Typical Output Waveform at 5 Gb/s with PRBS 2^23−1 (Vinpp = 75 mV) **Input signal DDJ = 7.2 ps Voltage (50 mV/div) *Input signal DDJ = 6.4 ps Voltage (50 mV/div) DDJ = 1.2 ps** DDJ = 2 ps*** DDJ = 2 ps*** Time (18.6 ps/div) Time (18.2 ps/div) Figure 6. Typical Output Waveform at 10.7 Gb/s with PRBS 2^23−1 (Vinpp = 75 mV) Figure 7. Typical Output Waveform at 12 Gb/s with PRBS 2^23−1 (Vinpp = 75 mV) ***Input signal DDJ = 11 ps ***Input signal DDJ = 13 ps http://onsemi.com 6 NB7L11M CLK VINPP = VIH(CLK) − VIL(CLK) CLK Q VOUTPP = VOH(Q) − VOL(Q) Q tPHL tPLH Figure 8. AC Reference Measurement NB7L11M VCC 50 W Receiver Device VCC 50 W 50 W 50 W Q CLK Z = 50 W Q CLK Z = 50 W Figure 9. Typical Termination for Output Driver Using External Termination Resistor (Refer to Application Notes AND8020/D and AND8173/D) CLK CLK CLK CLK Vth Vth Figure 10. Differential Input Driven Single−Ended VCC Vthmax Vthmin GND VCC VIHmax VILmax CLK Vth Figure 11. Differential Inputs Driven Differentially VIHCLKmax VCMmax CLK VIH Vth VIL VCMR CLK VIHmin VILmin VCMmax GND Figure 12. Vth Diagram VILCLKmax V(CLK) = VIHCLK − VILCLK VIHCLKtyp VILCLKtyp VIHCLKmin VILCLKmin Figure 13. VCMR Diagram http://onsemi.com 7 NB7L11M VCC 50 W 50 W Q Q 16 mA VEE Figure 14. CML Output Structure Table 6. INTERFACING OPTIONS INTERFACING OPTIONS CONNECTIONS CML Connect VTCLK, VTCLK to VCC LVDS Connect VTCLK, VTCLK together CLK input AC−COUPLED Bias VTCLK, VTCLK Inputs within (VCMR) Common Mode Range RSECL, LVPECL Standard ECL Termination Techniques. See AND8020/D. LVTTL, LVCMOS An external voltage should be applied to the unused complementary differential input. Nominal voltage is 1.5 V for LVTTL and VCC/2 for LVCMOS inputs. http://onsemi.com 8 NB7L11M Application Information minimum input swing of 75 mV and the maximum input swing of 2500 mV. Within these conditions, the input voltage can range from VCC to 1.2 V. Examples interfaces are illustrated below in a 50 W environment (Z = 50 W). All NB7L11M inputs can accept PECL, CML, LVTTL, LVCMOS and LVDS signal levels. The limitations for differential input signal (LVDS, PECL, or CML) are VCC VCC 50 W 50 W Q CLK Z CML Driver VCC VCC VTCLK 50 W VTCLK 50 W NB7L11M Z Q CLK VEE VEE Figure 15. CML to CML Interface VCC VCC 50 W VBias PECL Driver VBias Recommended RT Values VCC 50 W RT RT 5.0 V 290 W CLK Z VTCLK 50 W NB7L11M VTCLK 50 W Z CLK RT 3.3 V 150 W 2.5 V 80 W VEE VEE VEE Figure 16. PECL to CML Receiver Interface http://onsemi.com 9 NB7L11M VCC VCC CLK Z 50 W VTCLK LVDS Driver NB7L11M VTCLK 50 W Z CLK VEE VEE Figure 17. LVDS to CML Receiver Interface VCC VCC CLK Z LVTTL/ LVCMOS Driver VTCLK No Connect* No Connect NB7L11M VTCLK VREF VEE 50 W *or 60 pF to GND 50 W Recommended VREF Values VREF CLK VCC LVCMOS VCC − VEE 2 LVTTL 1.5 V Figure 18. LVCMOS/LVTTL to CML Receiver Interface ORDERING INFORMATION Package Shipping † QFN−16 123 Units/Rail NB7L11MMNG QFN−16 (Pb−Free) 123 Units/Rail NB7L11MMNR2 QFN−16 3000 Tape & Reel QFN−16 (Pb−Free) 3000 Tape & Reel Device NB7L11MMN NB7L11MMNR2G †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 10 NB7L11M PACKAGE DIMENSIONS 16 PIN QFN MN SUFFIX CASE 485G−01 ISSUE B ÇÇÇ ÇÇÇ ÇÇÇ D PIN 1 LOCATION 0.15 C NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.25 AND 0.30 MM FROM TERMINAL. 4. COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS THE TERMINALS. 5. Lmax CONDITION CAN NOT VIOLATE 0.2 MM MINIMUM SPACING BETWEEN LEAD TIP AND FLAG A B E DIM A A1 A3 b D D2 E E2 e K L TOP VIEW 0.15 C (A3) 0.10 C A 16 X 0.08 C SIDE VIEW MILLIMETERS MIN MAX 0.80 1.00 0.00 0.05 0.20 REF 0.18 0.30 3.00 BSC 1.65 1.85 3.00 BSC 1.65 1.85 0.50 BSC 0.20 −−− 0.30 0.50 SEATING PLANE A1 C D2 16X L 5 NOTE 5 16X e 4 9 1 12 E2 K 16 16X e 13 b 0.10 C A B 0.05 C EXPOSED PAD 8 BOTTOM VIEW NOTE 3 ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: N. American Technical Support: 800−282−9855 Toll Free Literature Distribution Center for ON Semiconductor USA/Canada P.O. Box 61312, Phoenix, Arizona 85082−1312 USA Phone: 480−829−7710 or 800−344−3860 Toll Free USA/Canada Japan: ON Semiconductor, Japan Customer Focus Center 2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051 Fax: 480−829−7709 or 800−344−3867 Toll Free USA/Canada Phone: 81−3−5773−3850 Email: [email protected] http://onsemi.com 11 ON Semiconductor Website: http://onsemi.com Order Literature: http://www.onsemi.com/litorder For additional information, please contact your local Sales Representative. NB7L11M/D