NB7V32M 1.8V / 2.5V, 10GHz ÷2 Clock Divider with CML Outputs Multi−Level Inputs w/ Internal Termination http://onsemi.com Description The NB7V32M is a differential B2 Clock divider with asynchronous reset. The differential Clock inputs incorporate internal 50 W termination resistors and will accept LVPECL, CML and LVDS logic levels. The NB7V32M produces a B2 output copy of an input Clock operating up to 10 GHz with minimal jitter. The RESET Pin is asserted on the rising edge. Upon power−up, the internal flip−flops will attain a random state; the Reset allows for the synchronization of multiple NB7V32M’s in a system. The 16 mA differential CML output provides matching internal 50 W termination which guarantees 400 mV output swing when externally receiver terminated with 50 W to VCC . The NB7V32M is the 1.8 V/2.5 V version of the NB7L32M (2.5 V/3.3 V) and is offered in a low profile 3 mm x 3 mm 16−pin QFN package. The NB7V32M is a member of the GigaComm™ family of high performance clock products. Application notes, models, and support documentation are available at www.onsemi.com. MARKING DIAGRAM* 1 16 NB7V 32M ALYWG G 1 QFN−16 MN SUFFIX CASE 485G A = Assembly Location L = Wafer Lot Y = Year W = Work Week G = Pb−Free Package (Note: Microdot may be in either location) *For additional marking information, refer to Application Note AND8002/D. Features • • • • • • • • • • Maximum Input Clock Frequency > 10 GHz, typical Random Clock Jitter < 0.8 ps RMS 200 ps Typical Propagation Delay 35 ps Typical Rise and Fall Times Differential CML Outputs, 400 mV Peak−to−Peak, Typical Operating Range: VCC = 1.71 V to 2.625 V with GND = 0 V Internal 50 W Input Termination Resistors QFN−16 Package, 3 mm x 3 mm −40°C to +85°C Ambient Operating Temperature These are Pb−Free Devices R RESET VTCLK 50W CLK B2 CLK Q Q 50W VTCLK VREFAC Figure 1. Simplified Logic Diagram ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 8 of this data sheet. © Semiconductor Components Industries, LLC, 2009 November, 2009 − Rev. 4 1 Publication Order Number: NB7V32M/D NB7V32M VCC 16 R 15 VCC VCC 14 Exposed Pad (EP) VTCLK 1 12 VCC 11 Q 3 10 Q VTCLK 4 9 VCC CLK Table 1. TRUTH TABLE 13 2 5 6 7 CLK R Q Q x x H L H Z W L CLK B 2 CLK B 2 Z = LOW to HIGH Transition W = HIGH to LOW Transition x = Don’t Care NB7V32M CLK CLK 8 VREFAC GND GND GND Figure 2. Pin Configuration (Top View) Table 2. PIN DESCRIPTION Pin Name I/O Description 1 VTCLK − 2 CLK LVPECL, CML, LVDS Input Non−inverted Differential CLK Input. (Note 1) 3 CLK LVPECL, CML, LVDS Input Inverted Differential CLK Input. (Note 1) 4 VTCLK − Internal 50 W Termination Pin for CLK 5 VREFAC − Internally Generated Output Voltage Reference for Capacitor−Coupled Inputs, only 6 GND − Negative Supply Voltage 7 GND − Negative Supply Voltage 8 GND − Negative Supply Voltage 9 VCC − Positive Supply Voltage. (Note 2) 10 Q CML Output Inverted Differential Output 11 Q CML Output Non−Inverted Differential Output 12 VCC − Positive Supply Voltage. (Note 2) 13 VCC − Positive Supply Voltage. (Note 2) 14 VCC − Positive Supply Voltage. (Note 2) 15 R LVCMOS Input 16 VCC − Positive Supply Voltage. (Note 2) − EP − The Exposed Pad (EP) on the QFN−16 package bottom is thermally connected to the die for improved heat transfer out of package. The exposed pad must be attached to a heat−sinking conduit. The pad is electrically connected to the die, and must be electrically and thermally connected to GND on the PC board. Internal 50 W Termination Pin for CLK Asynchronous Reset Input. Internal 75 kW pulldown to GND. 1. In the differential configuration when the input termination pins (VTCLK, VTCLK) are connected to a common termination voltage or left open, and if no signal is applied on CLK/CLK input, then the device will be susceptible to self−oscillation. Q/Q outputs have internal 50 W source termination resistors. 2. VCC and GND pins must be externally connected to a power supply for proper operation. http://onsemi.com 2 NB7V32M Table 3. ATTRIBUTES Characteristics ESD Protection Value Human Body Model Machine Model Moisture Sensitivity 16−QFN Flammability Rating Oxygen Index: 28 to 34 > 4 kV > 200 V Level 1 UL 94 V−0 @ 0.125 in Transistor Count 164 Meets or exceeds JEDEC Spec EIA/JESD78 IC Latchup Test For additional information, see Application Note AND8003/D. Table 4. MAXIMUM RATINGS Symbol Rating Unit VCC Positive Power Supply GND = 0 V 3.0 V VIN Positive Input Voltage GND = 0 V 1.89 V Differential Input Voltage |D − D| 1.89 V Input Current Through RT (50 W Resistor) $40 mA Output Current Through RT (50 W Resistor) $40 mA VINPP IIN IOUT IVREFAC Parameter Condition 1 Condition 2 VREFAC Sink/Source Current $1.5 mA TA Operating Temperature Range −40 to +85 °C Tstg Storage Temperature Range −65 to +150 °C qJA Thermal Resistance (Junction−to−Ambient) (Note 3) QFN−16 QFN−16 42 35 °C/W °C/W qJC Thermal Resistance (Junction−to−Case) (Note 3) QFN−16 4 °C/W Tsol Wave Solder Pb−Free 265 °C 0 lfpm 500 lfpm Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 3. JEDEC standard multilayer board − 2S2P (2 signal, 2 power) with 8 filled thermal vias under exposed pad. http://onsemi.com 3 NB7V32M Table 5. DC CHARACTERISTICS POSITIVE CML OUTPUT VCC = 1.71 V to 2.625 V; GND = 0 V; TA = −40°C to 85°C (Note 4) Min Characteristic Symbol Typ Max 90 80 100 90 Unit POWER SUPPLY CURRENT ICC Power Supply Current (Inputs and Outputs Open) VCC = 2.5 V $ 5% VCC = 1.8 V $ 5% mA CML OUTPUTS VOH Output HIGH Voltage (Note 5) VOL Output LOW Voltage (Note 5) VCC = 2.5 V VCC = 1.8 V VCC – 30 2470 1770 VCC – 1 2490 1790 VCC 2500 1800 VCC = 2.5 V VCC = 2.5 V VCC – 600 1900 VCC – 500 2000 VCC – 400 2100 VCC = 1.8 V VCC = 1.8 V VCC – 550 1250 VCC – 450 1350 VCC – 350 1450 mV mV DIFFERENTIAL INPUTS DRIVEN SINGLE−ENDED (Note 6) (Figures 5 and 7) Vth Input Threshold Reference Voltage Range (Note 7) 1050 VCC − 100 mV VIH Single−Ended Input HIGH Voltage Vth + 100 VCC mV VIL Single−Ended Input LOW Voltage GND Vth − 100 mV VISE Single−Ended Input Voltage (VIH − VIL) 200 1200 mV VCC – 850 VCC – 750 VCC – 500 VCC – 450 VREFAC VREFAC Output Reference Voltage @ 100 mA for capacitor− coupled inputs, only VCC = 2.5 V (Note 8) VCC = 1.8 V mV DIFFERENTIAL INPUTS DRIVEN DIFFERENTIALLY (Figures 6 and 9) (Note 9) VIHD Differential Input HIGH Voltage 1100 VCC mV VILD Differential Input LOW Voltage GND VCC − 100 mV VID Differential Input Voltage (VIHD − VILD) 100 1200 mV VCMR Input Common Mode Range (Differential Configuration, Note 10) (Figure 9) 1050 VCC − 50 mV IIH Input HIGH Current (VTCLK/VTCLK Open) −150 150 uA IIL Input LOW Current (VTCLK/VTCLK Open) −150 150 uA CONTROL INPUT (Reset Pin) VIH Input HIGH Voltage for Control Pin VCC − 200 VCC mV VIL Input LOW Voltage for Control Pin GND 200 mV IIH Input HIGH Current −150 150 uA IIL Input LOW Current −150 150 uA TERMINATION RESISTORS RTIN Internal Input Termination Resistor (@ 10 mA) 45 50 55 W RTOUT Internal Output Termination Resistor (@ 10 mA) 45 50 55 W NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 4. Input and output parameters vary 1:1 with VCC. 5. CML outputs loaded with 50 W to VCC for proper operation. 6. Vth, VIH, VIL and VISE parameters must be complied with simultaneously. 7. Vth is applied to the complementary input when operating in single−ended mode. 8. VREFAC will not be less than GND + 1050 mV. 9. VIHD, VILD, VID and VCMR parameters must be complied with simultaneously. http://onsemi.com 4 NB7V32M 10. VCMR min varies 1:1 with GND, VCMR max varies 1:1 with VCC. The VCMR range is referenced to the most positive side of the differential input signal. Table 6. AC CHARACTERISTICS VCC = 1.71 V to 2.625 V; GND = 0 V; TA = −40°C to 85°C (Note 11) Symbol Characteristic Min Typ fMAX Maximum Input Clock Frequency VOUTPP Output Voltage Amplitude (@ VINPPmin) (Note 12) (Figure 3) tPLH, tPHL Propagation Delay to Differential Outputs, @ 1 GHz, measured at differential cross−point tPLH TC Propagation Delay Temperature Coefficient tskew Duty Cycle Skew (Note 13) Device − Device skew (tpdmax – tpdmin) tRR Reset Recovery (See Figure 11) 300 135 tPW Minimum Pulse Width R 500 200 tDC Output Clock Duty Cycle (Reference Duty Cycle = 50%) fin v 10 GHz 45 tJITTER RJ – Output Random Jitter (Note 14) fin v 10 GHz VINPP Input Voltage Swing (Differential Configuration) (Figure 10) (Note 15) tr, tf Output Rise/Fall Times @ 1 GHz (20% − 80%), Q, Q Max 10 Unit GHz fin ≤ 10GHz 280 400 CLK/CLK to Q, Q R to Q, Q 150 200 200 mV 275 50 ps Dfs/°C 20 50 ps 50 55 % 0.2 0.8 ps RMS 1200 mV 60 ps 100 35 NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 11. Measured using a 1 GHz, VINPPmin, 50% duty−cycle clock source. All output loading with external 50 W to VCC. Input edge rates 40 ps (20% − 80%). 12. Output voltage swing is a single−ended measurement operating in differential mode. 13. Duty cycle skew is defined only for differential operation when the delays are measured from cross−point of the inputs to the cross−point of the outputs. Duty cycle skew is measured between differential outputs using the deviations of the sum of Tpw− and Tpw+ @ 1 GHz. Skew is measured between outputs under identical transitions and conditions. 14. Additive RMS jitter with 50% duty cycle clock signal. 15. Input voltage swing is a single−ended measurement operating in differential mode. OUTPUT VOLTAGE AMPLITUDE (mV) 500 VCC 450 VTCLK Q AMP (mV) 400 50 W RC RC CLK 350 I 300 CLK 250 50 W 200 0 2 4 6 8 10 VTCLK fin, Clock Input Frequency (GHz) Figure 3. CLOCK Output Voltage Amplitude (VOUTPP) vs. Input Frequency (fin) at Ambient Temperature (Typ) Figure 4. Input Structure http://onsemi.com 5 NB7V32M CLK VIH Vth CLK VIL CLK CLK Vth Figure 5. Differential Input Driven Single−Ended VCC Vthmax Figure 6. Differential Inputs Driven Differentially VIHmax VILmax VIH Vth VIL Vth VILD VILmin GND Figure 7. Vth Diagram VCC Figure 8. Differential Inputs Driven Differentially VIHDmax VCMmax CLK VILDmax CLK VCMR CLK GND VIHD CLK VIHmin Vthmin VCMmin VID = |VIHD(CLK) − VILD(CLK)| CLK VINPP = VIH(CLK) − VIL(CLK) CLK VIHDtyp VID = VIHD − VILD Q VILDtyp VOUTPP = VOH(Q) − VOL(Q) Q VIHDmin tPHL VILDmin tPLH Figure 9. VCMR Diagram Figure 10. AC Reference Measurement 50% 50% VOUTPP = VOH(Q) − VOL(Q) Q tPLH tPHL 50% 50% CLK R tRR(MIN) 50% Figure 11. AC Reference Measurement (Timing Diagram) http://onsemi.com 6 VINPP = VIH(CLK) − VIL(CLK) NB7V32M VCC VCC VCC ZO = 50 W LVPECL Driver Vth ZO = 50 W VCC ZO = 50 W CLK NB7V32M CLK 50 W VTCLK VTCLK VTCLK LVDS Driver VTCLK ZO = 50 W 50 W CLK 50 W 50 W CLK Vth = VCC − 2 V VEE NB7V32M GND VEE GND Figure 12. LVPECL Interface Figure 13. LVDS Interface VCC VCC ZO = 50 W CML Driver VCC CLK NB7V32M 50 W VTCLK VTCLK ZO = 50 W VT = VT = VCC 50 W CLK GND GND Figure 14. Standard 50 W Load CML Interface VCC ZO = 50 W CLK Differential Driver VCC VCC Vth VTCLK VTCLK ZO = 50 W VCC ZO = 50 W NB7V32M 50 W Single−Ended Driver 50 W Vth VTCLK VTCLK CLK NB7V32M 50 W 50 W CLK Vth = VREFAC GND CLK Vth = VREFAC GND GND GND Figure 16. Capacitor−Coupled Single−Ended Interface (VTCLK/VTCLK Connected to VREFAC; VREFAC Bypassed to Ground with 0.1 mF Capacitor) Figure 15. Capacitor−Coupled Differential Interface (VTCLK/VTCLK Connected to VREFAC; VREFAC Bypassed to Ground with 0.1 mF Capacitor) http://onsemi.com 7 NB7V32M NB7V32M Receiver VCC VCC (Receiver) 50 W 50 W Q 50 W 50 W Q 16 mA GND Figure 17. Typical CML Output Structure and Termination VCC 50 W Z = 50 W DUT Driver Device 50 W Q D Receiver Device Z = 50 W Q D Figure 18. Typical Termination for CML Output Driver and Device Evaluation ORDERING INFORMATION Package Shipping† NB7V32MMNG QFN−16 (Pb−free) 123 Units / Rail NB7V32MMNTXG QFN−16 (Pb−free) 3000 / Tape & Reel Device †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 8 NB7V32M PACKAGE DIMENSIONS 16 PIN QFN CASE 485G−01 ISSUE D D ÇÇÇ ÇÇÇ ÇÇÇ L1 DETAIL A PIN 1 LOCATION ALTERNATE TERMINAL CONSTRUCTIONS E ÉÉ ÉÉ EXPOSED Cu 0.15 C TOP VIEW 0.15 C DETAIL B 0.10 C NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.25 AND 0.30 MM FROM TERMINAL. 4. COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS THE TERMINALS. 5. Lmax CONDITION CAN NOT VIOLATE 0.2 MM MINIMUM SPACING BETWEEN LEAD TIP AND FLAG L L A B A3 MOLD CMPD A1 DETAIL B (A3) ÉÉ ÇÇ ÇÇ ALTERNATE CONSTRUCTIONS A 16 X SEATING PLANE 0.08 C SIDE VIEW 16X L A1 5 NOTE 5 8 4 16X e 0.575 0.022 EXPOSED PAD 3.25 0.128 0.30 0.012 EXPOSED PAD 9 E2 K 12 1 16 16X e 1.50 0.059 3.25 0.128 13 b 0.10 C A B 0.05 C MILLIMETERS MIN MAX 0.80 1.00 0.00 0.05 0.20 REF 0.18 0.30 3.00 BSC 1.65 1.85 3.00 BSC 1.65 1.85 0.50 BSC 0.18 TYP 0.30 0.50 0.00 0.15 SOLDERING FOOTPRINT* C D2 DETAIL A DIM A A1 A3 b D D2 E E2 e K L L1 BOTTOM VIEW NOTE 3 0.30 0.012 0.50 0.02 SCALE 10:1 mm Ǔ ǒinches *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. The products described herein (NB7V32M), may be covered by U.S. patents including 6,362,644. There may be other patents pending. GigaComm is a trademark of Semiconductor Components Industries, LLC (SCILLC). ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Japan: ON Semiconductor, Japan Customer Focus Center 2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051 Phone: 81−3−5773−3850 http://onsemi.com 9 ON Semiconductor Website: http://onsemi.com Order Literature: http://www.onsemi.com/litorder For additional information, please contact your local Sales Representative. NB7V32M/D