ALUMINUM ELECTROLYTIC CAPACITORS HC Low Impedance Approved by Reliability Center for Electronic Component, Japan-Certification No. RCJ-03-23C series Lower impedance than HD series. Adapted to the RoHS directive (2002/95/EC). HC Low Impedance HD Specifications ltem Performance Characteristics Category Temperature Range – 40 ~ +105˚C Rated Voltage Range 6.3 ~ 35V Rated Capacitance Range 4.7 ~ 1000µF Capacitance Tolerance ± 20% at 120Hz, 20˚C Leakage Current After 2 minutes' application of rated voltage, leakage current is less than 0.01CV or 3 (µA), whichever is greater. Rated voltage (V) 6.3 10 16 25 35 tan δ (MAX.) 0.15 0.13 0.12 0.10 0.10 Rated voltage (V) 6.3 10 16 25 35 Impedance ratio ZT / Z20 (MAX.) Z–40˚C / Z+20˚C 2 2 2 2 2 tan δ Stability at Low Temperature 120Hz 20˚C 120Hz < 6.3 : 1000 hours ) at 105˚C the peak After an application of D.C. bias voltage plus the rated ripple current for 2000 hours (φD = voltage shall not exceed the rated D.C. voltage, capacitors meet the characteristic requirements listed below. Endurance Marking Capacitance change Within ± 20% of initial value tan δ 200% or less of initial specified value Leakage current lnitial specified value or less Printed with white color letter on black sleeve. Type numbering system (Example : 10V 470µF) Radial Lead Type fd 1 2 3 4 5 6 7 8 9 10 11 UHC 1 A 4 7 1 M PD Configuration Capacitance tolerance (± 20%) Rated Capacitance (470mF) Rated voltage (10V) Series name Type f P ± 0.5 D+0.5 MAX. Sleeve (P.E.T.) Pressure relief vent 15MIN L+ MAX. (f6.3up) (No pressure relief vent for 7mmL products) (L = 7) 1.0 (L 11) 1.5 4MIN D 4 5 P 1.5 2.0 f d 0.45 0.45 f (mm) 6.3 8 10 2.5 3.5 5.0 0.5 0.6 0.6 (0.45) ( ) : Applied to 7mmL products Configuration Pb-free leadwire fD Pb-free PET sleeve 4 5 DD 6.3 (7L) 6.3 (11L) ED 8 á 10 PD • Please refer to page 21 about the end seal configulation. Please refer to page 21, 22, 23 about the formed or taped product spec. Please refer to page 3 for the minimum order quantity. Dimension table in next page. CAT.8100V ALUMINUM ELECTROLYTIC CAPACITORS HC series Standard ratings V (Code) Item Cap.(µF) Code 6.3 (0J) Case size φD × L (mm) 10 (1A) Impedance (Ω ) MAX. Rated ripple (mArms) 20˚C / 100kHz 105˚C / 100kHz Case size φD × L (mm) 16 (1C) Impedance (Ω ) MAX. Rated ripple (mArms) 20˚C / 100kHz 105˚C / 100kHz Case size φD × L (mm) Impedance (Ω ) MAX. Rated ripple (mArms) 20˚C / 100kHz 105˚C / 100kHz 22 220 4×7 0.49 230 5×7 0.26 350 33 330 4×7 0.48 230 5×7 0.26 350 5×7 0.26 350 47 470 5×7 0.26 350 5×7 0.26 350 6.3 × 7 0.15 480 100 101 6.3 × 7 0.15 480 6.3 × 7 0.15 480 6.3 × 11 0.078 640 220 221 6.3 × 11 0.077 640 8 × 11.5 0.044 910 8 × 11.5 0.044 910 330 331 8 × 11.5 0.043 910 8 × 11.5 0.043 910 10 × 12.5 0.030 1230 470 471 8 × 11.5 10 × 12.5 0.030 1230 10 × 16 0.025 1650 1000 102 0.043 910 10 × 16 0.024 1650 Case size φD × L (mm) Impedance (Ω ) MAX. Rated ripple V (Code) Item Cap. (µF) Code 25 (1E) 35 (1V) (mArms) 20˚C / 100kHz 105˚C / 100kHz Case size φD × L (mm) Impedance (Ω ) MAX. Rated ripple (mArms) 20˚C / 100kHz 105˚C / 100kHz 4×7 0.64 230 10 100 4×7 0.52 230 5×7 0.33 350 22 220 5×7 0.27 350 6.3 × 7 0.17 480 33 330 6.3 × 7 0.16 480 6.3 × 7 0.16 480 47 470 6.3 × 7 0.15 480 6.3 × 11 0.089 640 100 101 6.3 × 11 0.078 640 220 221 10 × 12.5 0.031 1230 330 331 10 × 16 0.026 1650 4.7 4R7 8 × 11.5 10 × 16 0.048 910 0.026 1650 Frequency coefficient of rated ripple current Frequency 120Hz 1kHz 10kHz 100kHz 0.40 0.68 0.90 1.00 47 ~ 330 0.47 0.75 0.95 1.00 470 ~ 1000 0.55 0.85 0.98 1.00 Cap. (µF) 4.7 ~ 33 CAT.8100V