PRODUCT SPECIFICATION TITLE 2.4/ 5GHz Stand Alone Antenna (34.9mm*9mm) TABLE OF CONTENTS 1.0 SCOPE 2.0 PRODUCT DESCRIPTION 3.0 APPLICABLE DOCUMENTS AND SPECIFICATIONS 4.0 RATINGS 5.0 PERFORMANCE 6.0 TEST GROUPINGS 7.0 PACKING REVISION: ECR/ECN INFORMATION: TITLE: C EC No: ABU2012-0075 DATE: 2012-06-19 DOCUMENT NUMBER: PS-47950-001 SHEET No. 2.4/5GHZ Stand Alone Antenna(34.9mm*9mm) CREATED / REVISED BY: CHECKED BY: 1 of 6 APPROVED BY: Serena Zhang2011-05-23 Amos Cheah2011-05-23 Welson Tan2011-05-23 TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC PRODUCT SPECIFICATION 2.4/5GHZ Stand Antenna 1.0 SCOPE This Product Specification covers the mechanical, electrical and environmental performances requirements and test methods for 2.4/5GHz stand alone antenna. 2.0 PRODUCT DESCRIPTION 2.1 PRODUCT NAME AND SERIES NUMBER (S) Product name: 2.4/5 GHZ Stand Alone Antenna 47950-**** 2.2 Design and Construction Antenna shall be of the design, construction and physical dimensions specified on the applicable sales drawing. 2.3 Materials a) Flex: Refer to respective Molex sales or engineering drawings b) Plating: Refer to respective Molex sales or engineering drawings c) Cable Line: Refer to respective Molex sales or engineering drawings d) Connector: Refer to respective Molex sales or engineering drawings 3.0 APPLICABLE DOCUMENTS AND SPECIFICATIONS See drawings and other sections of this specification for the relevant reference documents. In cases where the specification differs from the drawings, the drawings take precedence. 4.0 RATINGS 4.1 RF POWER 2 WATTS 4.2 TEMPERATU Operating: Storage : - 30°C to + 75°C - 30°C to + 75°C 4.3 HUMIDITY Storage : Test : +15~70% RH +80~95% RH REVISION: ECR/ECN INFORMATION: TITLE: C EC No: ABU2012-0075 DATE: 2012-06-19 DOCUMENT NUMBER: PS-47950-001 SHEET No. 2.4/5GHZ Stand Alone Antenna(34.9mm*9mm) CREATED / REVISED BY: CHECKED BY: 2 of 6 APPROVED BY: Serena Zhang2011-05-23 Amos Cheah2011-05-23 Welson Tan2011-05-23 TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC PRODUCT SPECIFICATION 5.0 PERFORMANCE 5.1 ELECTRICAL REQUIREMENTS FOR CABLE LENGTH 100mm (47950-0001) ITEM DESCRIPTION TEST CONDITION REQUIREMENT 5.1.1 Frequency Range 2.3GHz~5.85GHz 2.4GHz~2.5GHz 4.8GHz~6.0GHz 5.1.2 Return Loss Antenna loads on PC/ABS housing with 100mm; 1.13mm diameter micro coax cable. Measured by VNA5071C 5.1.3 Peak Gain Measure antenna on recommended PC/ABS housing through OTA chamber 3.0 dBi 4.6 dBi 5.1.4 Total Efficiency Measure antenna on recommended PC/ABS housing through OTA chamber >75% >70% 5.1.5 Polarization Measure antenna through the OTA chamber Liner 5.1.6 Input Impedance Measure antenna on recommended PCB through VNA E5071C 50Ohms < -10 dB 5.2 ELECTRICAL REQUIREMENTS FOR CABLE LENGTH 150mm (47950-1001) ITEM DESCRIPTION TEST CONDITION REQUIREMENT 5.2.1 Frequency Range 2.3GHz~5.85GHz 2.4GHz~2.5 4.8GHz~5.0 5.0GHZ~5. GHz GHz 85GHz 5.2.2 Return Loss Antenna loads on PC/ABS housing with 100mm; 1.13mm diameter micro coax cable. Measured by VNA5071C < -10 dB < -6 dB < -10 dB 5.2.3 Peak Gain Measure antenna on recommended PC/ABS housing through OTA chamber 3.0 dBi 2.7 dBi 3.7 dBi 5.2.4 Total Efficiency Measure antenna on recommended PC/ABS housing through OTA chamber >75% >60% >70% 5.2.5 Polarization Measure antenna through the OTA chamber Liner 5.2.6 Input Impedance Measure antenna on recommended PCB through VNA E5071C 50Ohms REVISION: ECR/ECN INFORMATION: TITLE: C EC No: ABU2012-0075 DATE: 2012-06-19 DOCUMENT NUMBER: PS-47950-001 SHEET No. 2.4/5GHZ Stand Alone Antenna(34.9mm*9mm) CREATED / REVISED BY: CHECKED BY: 3 of 6 APPROVED BY: Serena Zhang2011-05-23 Amos Cheah2011-05-23 Welson Tan2011-05-23 TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC PRODUCT SPECIFICATION 5.3 ELECTRICAL REQUIREMENTS FOR CABLE LENGTH 200mm (47950-2001) ITEM DESCRIPTION TEST CONDITION REQUIREMENT 5.3.1 Frequency Range 2.3GHz~5.85GHz 2.4GHz~2.5GHz 4.8GHz~6.0GHz 5.3.2 Return Loss Antenna loads on PC/ABS housing with 100mm; 1.13mm diameter micro coax cable. Measured by VNA5071C 5.3.3 Peak Gain Measure antenna on recommended PC/ABS housing through OTA chamber 2.9 dBi 5.0 dBi 5.3.4 Total Efficiency Measure antenna on recommended PC/ABS housing through OTA chamber >75% >70% 5.3.5 Polarization Measure antenna through the OTA chamber Liner 5.3.6 Input Impedance Measure antenna on recommended PCB through VNA E5071C 50Ohms < -10 dB 5.4 MECHANICAL REQUIREMENTS ITEM 1 DESCRIPTION Pull test TEST CONDITION REQUIREMENT Test machine :Max intelligent load tester Stick the flex antenna in a PC block, pull cable in horizontal direction Pull force >4.5N 5.5 RELIABILITY REQUIREMENTS ITEM DESCRIPTION TEST CONDITION REQUIREMENT 5.5.1 Cross section Cross section on pad soldering area. Check under microscope No soldering problem REVISION: ECR/ECN INFORMATION: TITLE: C EC No: ABU2012-0075 DATE: 2012-06-19 DOCUMENT NUMBER: PS-47950-001 SHEET No. 2.4/5GHZ Stand Alone Antenna(34.9mm*9mm) CREATED / REVISED BY: CHECKED BY: 4 of 6 APPROVED BY: Serena Zhang2011-05-23 Amos Cheah2011-05-23 Welson Tan2011-05-23 TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC PRODUCT SPECIFICATION 5.6 ENVIRONMENTAL REQUIREMENTS ITEM DESCRIPTION 5.6.1 1.Test condition: The device under test is kept for 12 hours in an environment with a temperature of 55 degrees and a relating humidity of 95%. 1) Parts should meet RF Thereafter for 12 Hours in an environment with Humidity Test spec before and after test. a temperature of 25 degrees and a relative 2） No cosmetic problem humidity of 95%. The cycle is repeated until a total of 6 cycles have been completed. Hereafter the conditions are stabilized at room temperature. 5.6.2 1.Test condition: The product temperature is decreased from room temperature to -40 degrees during 2 Hours and kept there for 2 hours. Then temperature is increased to 85 degree during 2 1) Parts should meet RF hours and kept for 2 hours. The temperature is spec before and after test. then again decreased to -40 degrees during a 2） No cosmetic problem 2-hours period. The cycle is repeated until a total of 6 cycles have been completed. Hereafter the conditions are stabilized at room temperature. 5.6.3 Temperature cycling test Salt mist test TEST CONDITION REQUIREMENT 1.Test condition: The device under test is exposed to a spray of 1) Parts should meet RF a 5% (by volume) resolution of Nacl in water spec before and after test. for 2 hours. Thereafter the device under test is left for 1 week in room temperature at a relative humidity of 95%. The cycle is repeated 2) No visible corrosion. until a total of 2 cycles have been completed. Discoloration accept. Here after the conditions are stabilized at room temperature. The meaning of text “No Cosmetic Problem” in the table above is: a. no soldering problem b. no adhesion problem of glue c. no peel off of plating REVISION: ECR/ECN INFORMATION: TITLE: C EC No: ABU2012-0075 DATE: 2012-06-19 DOCUMENT NUMBER: PS-47950-001 SHEET No. 2.4/5GHZ Stand Alone Antenna(34.9mm*9mm) CREATED / REVISED BY: CHECKED BY: 5 of 6 APPROVED BY: Serena Zhang2011-05-23 Amos Cheah2011-05-23 Welson Tan2011-05-23 TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC PRODUCT SPECIFICATION 6.0 TEST GROUPINGS Test Item Description Group1 5.5.1 Cross section X 5.6.1 Humidity Test 5.6.2 Temperature cycling test 5.6.3 Salt mist test Sample Quantity Group2 Group3 Group4 X X X 5 5 5 5 7.0 PACKAGING Refer to the Molex related packaging drawings. REVISION: ECR/ECN INFORMATION: TITLE: C EC No: ABU2012-0075 DATE: 2012-06-19 DOCUMENT NUMBER: PS-47950-001 SHEET No. 2.4/5GHZ Stand Alone Antenna(34.9mm*9mm) CREATED / REVISED BY: CHECKED BY: 6 of 6 APPROVED BY: Serena Zhang2011-05-23 Amos Cheah2011-05-23 Welson Tan2011-05-23 TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A4](V.1).DOC