SN74AUC1G125 SINGLE BUS BUFFER GATE WITH 3-STATE OUTPUT SCES382G – MARCH 2002 – REVISED JUNE 2003 D D D D D D D D D DBV OR DCK PACKAGE (TOP VIEW) Available in the Texas Instruments NanoStar and NanoFree Packages Optimized for 1.8-V Operation and Is 3.6-V I/O Tolerant to Support Mixed-Mode Signal Operation Ioff Supports Partial-Power-Down Mode Operation Sub 1-V Operable Max tpd of 2.5 ns at 1.8 V Low Power Consumption, 10-µA Max ICC ±8-mA Output Drive at 1.8 V Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II ESD Protection Exceeds JESD 22 – 2000-V Human-Body Model (A114-A) – 200-V Machine Model (A115-A) – 1000-V Charged-Device Model (C101) OE A GND 1 5 VCC 4 Y 2 3 YEA, YEP, YZA, OR YZP PACKAGE (BOTTOM VIEW) GND A OE 3 4 Y 2 1 5 VCC description/ordering information This bus buffer gate is operational at 0.8-V to 2.7-V VCC, but is designed specifically for 1.65-V to 1.95-V VCC operation. The SN74AUC1G125 is a single line driver with a 3-state output. The output is disabled when the output-enable (OE) input is high. To ensure the high-impedance state during power up or power down, OE should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver. ORDERING INFORMATION ORDERABLE PART NUMBER PACKAGE† TA NanoStar WCSP (DSBGA) – YEA NanoFree WCSP (DSBGA) – YZA (Pb-free) –40°C –40 C to 85 85°C C NanoStar – WCSP (DSBGA) 0.23-mm Large Bump – YEP TOP-SIDE MARKING‡ SN74AUC1G125YEAR SN74AUC1G125YZAR Tape and reel _ _ _UM_ SN74AUC1G125YEPR NanoFree – WCSP (DSBGA) 0.23-mm Large Bump – YZP (Pb-free) SN74AUC1G125YZPR SOT (SOT-23) – DBV Tape and reel SN74AUC1G125DBVR U25_ SOT (SC-70) – DCK Tape and reel SN74AUC1G125DCKR UM_ † Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. ‡ DBV/DCK: The actual top-side marking has one additional character that designates the assembly/test site. YEA/YZA, YEP/YZP: The actual top-side marking has three preceding characters to denote year, month, and sequence code, and one following character to designate the assembly/test site. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. NanoStar and NanoFree are trademarks of Texas Instruments. Copyright 2003, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 SN74AUC1G125 SINGLE BUS BUFFER GATE WITH 3-STATE OUTPUT SCES382G – MARCH 2002 – REVISED JUNE 2003 description/ordering information (continued) NanoStar and NanoFree package technology is a major breakthrough in IC packaging concepts, using the die as the package. This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs, preventing damaging current backflow through the device when it is powered down. FUNCTION TABLE INPUTS OE A OUTPUT Y L H H L L L H X Z logic diagram (positive logic) OE A 1 2 4 Y absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 3.6 V Input voltage range, VI (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 3.6 V Voltage range applied to any output in the high-impedance or power-off state, VO (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 3.6 V Output voltage range, VO (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to VCC + 0.5 V Input clamp current, IIK (VI < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –50 mA Output clamp current, IOK (VO < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –50 mA Continuous output current, IO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20 mA Continuous current through VCC or GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±100 mA Package thermal impedance, θJA (see Note 2): DBV package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206°C/W DCK package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 252°C/W YEA/YZA package . . . . . . . . . . . . . . . . . . . . . . . . . . . 154°C/W YEP/YZP package . . . . . . . . . . . . . . . . . . . . . . . . . . . 132°C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input negative-voltage and output voltage ratings may be exceeded if the input and output current ratings are observed. 2. The package thermal impedance is calculated in accordance with JESD 51-7. 2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 SN74AUC1G125 SINGLE BUS BUFFER GATE WITH 3-STATE OUTPUT SCES382G – MARCH 2002 – REVISED JUNE 2003 recommended operating conditions (see Note 3) VCC Supply voltage VIH High-level input voltage VCC = 0.8 V VCC = 1.1 V to 1.95 V VCC = 2.3 V to 2.7 V VCC = 0.8 V MIN MAX 0.8 2.7 VCC 0.65 × VCC UNIT V V 1.7 0 0.35 × VCC VIL Low-level input voltage VI VO Input voltage 0 3.6 V Output voltage 0 VCC –0.7 V VCC = 1.1 V to 1.95 V VCC = 2.3 V to 2.7 V VCC = 0.8 V VCC = 1.1 V IOH IOL ∆t/∆v t/ v High-level output current Low-level output current Input transition rise or fall rate 0.7 –3 VCC = 1.4 V VCC = 1.65 V –5 VCC = 2.3 V VCC = 0.8 V –9 0.7 3 VCC = 1.65 V VCC = 2.3 V 8 VCC = 2.3 V to 2.7 V mA –8 VCC = 1.1 V VCC = 1.4 V VCC = 0.8 V to 1.6 V VCC = 1.65 V to 1.95 V V 5 mA 9 20 10 ns/V 3 TA Operating free-air temperature –40 85 °C NOTE 3: All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 SN74AUC1G125 SINGLE BUS BUFFER GATE WITH 3-STATE OUTPUT SCES382G – MARCH 2002 – REVISED JUNE 2003 electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER TEST CONDITIONS IOH = –100 µA IOH = –0.7 mA VOH VOL II Ioff A or OE input TYP† VCC MIN 0.8 V to 2.7 V VCC–0.1 0.8 V MAX 0.55 IOH = –3 mA IOH = –5 mA 1.1 V 0.8 1.4 V 1 IOH = –8 mA IOH = –9 mA 1.65 V 1.2 2.3 V 1.8 IOL = 100 µA IOL = 0.7 mA 0.8 V to 2.7 V V 0.2 0.8 V 0.25 IOL = 3 mA IOL = 5 mA 1.1 V 0.3 1.4 V 0.4 IOL = 8 mA IOL = 9 mA 1.65 V 0.45 2.3 V 0.6 VI = VCC or GND VI or VO = 2.7 V IOZ ICC VO = VCC or GND VI = VCC or GND, Ci VI = VCC or GND IO = 0 UNIT V 0 to 2.7 V ±5 µA 0 ±10 µA 2.7 V ±10 µA 0.8 V to 2.7 V 10 µA Co VO = VCC or GND † All typical values are at TA = 25°C. 2.5 V 2.5 pF 2.5 V 5.5 pF switching characteristics over recommended operating free-air temperature range, CL = 15 pF (unless otherwise noted) (see Figure 1) VCC = 1.2 V ± 0.1 V VCC = 1.5 V ± 0.1 V VCC = 1.8 V ± 0.15 V VCC = 2.5 V ± 0.2 V FROM (INPUT) TO (OUTPUT) VCC = 0.8 V TYP MIN MAX MIN MAX MIN TYP MAX MIN MAX tpd A Y 4.7 0.8 3.6 0.4 2.3 ‡ ‡ ‡ ‡ ‡ ns ten OE Y 5.4 0.7 4.1 0.5 2.6 ‡ ‡ ‡ ‡ ‡ ns 1.4 4.3 1.4 4 ‡ ‡ ‡ ‡ ‡ ns PARAMETER tdis OE 4.8 Y ‡ This information was not available at the time of publication. UNIT switching characteristics over recommended operating free-air temperature range, CL = 30 pF (unless otherwise noted) (see Figure 1) FROM (INPUT) TO (OUTPUT) tpd A ten tdis PARAMETER 4 VCC = 1.8 V ± 0.15 V VCC = 2.5 V ± 0.2 V UNIT MIN TYP MAX MIN MAX Y 0.7 1.5 2.5 0.9 1.7 ns OE Y 1 1.6 2.6 1.1 1.9 ns OE Y 1.8 2.2 3.1 0.8 1.7 ns POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 SN74AUC1G125 SINGLE BUS BUFFER GATE WITH 3-STATE OUTPUT SCES382G – MARCH 2002 – REVISED JUNE 2003 operating characteristics, TA = 25°C PARAMETER Cpd Power dissipation capacitance Outputs enabled Outputs disabled TEST CONDITIONS VCC = 0.8 V TYP VCC = 1.2 V TYP VCC = 1.5 V TYP VCC = 1.8 V TYP VCC = 2.5 V TYP 14 14 14 15 16 1.5 1.5 1.5 2 2.5 f = 10 MHz UNIT pF POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 5 SN74AUC1G125 SINGLE BUS BUFFER GATE WITH 3-STATE OUTPUT SCES382G – MARCH 2002 – REVISED JUNE 2003 PARAMETER MEASUREMENT INFORMATION 2 × VCC S1 RL From Output Under Test Open GND CL (see Note A) RL VCC 0.8 V 1.2 V ± 0.1 V 1.5 V ± 0.1 V 1.8 V ± 0.15 V 2.5 V ± 0.2 V 1.8 V ± 0.15 V 2.5 V ± 0.2 V LOAD CIRCUIT TEST S1 tPLH/tPHL tPLZ/tPZL tPHZ/tPZH Open 2 × VCC GND CL RL 15 pF 15 pF 15 pF 15 pF 15 pF 30 pF 30 pF 2 kΩ 2 kΩ 2 kΩ 2 kΩ 2 kΩ 1 kΩ 500 Ω V∆ 0.1 V 0.1 V 0.1 V 0.15 V 0.15 V 0.15 V 0.15 V VCC Timing Input VCC/2 0V tw tsu VCC VCC/2 Input VCC/2 th VCC VCC/2 Data Input VCC/2 0V 0V VOLTAGE WAVEFORMS SETUP AND HOLD TIMES VOLTAGE WAVEFORMS PULSE DURATION VCC VCC/2 Input VCC/2 0V tPHL tPLH VOH VCC/2 Output VCC/2 VOL VCC/2 VCC/2 VCC/2 VOL VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES INVERTING AND NONINVERTING OUTPUTS VCC/2 0V tPLZ tPZL VCC VCC/2 Output Waveform 2 S1 at GND (see Note B) VOL + V∆ VOL tPHZ tPZH VOH Output Output Waveform 1 S1 at 2 × VCC (see Note B) tPLH tPHL VCC Output Control VCC/2 VOH – V∆ VOH ≈0 V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES LOW- AND HIGH-LEVEL ENABLING NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, slew rate ≥ 1 V/ns. D. The outputs are measured one at a time with one transition per measurement. E. tPLZ and tPHZ are the same as tdis. F. tPZL and tPZH are the same as ten. G. tPLH and tPHL are the same as tpd. H. All parameters and waveforms are not applicable to all devices. Figure 1. Load Circuit and Voltage Waveforms 6 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 MECHANICAL DATA MPDS025C – FEBRUARY 1997 – REVISED FEBRUARY 2002 DCK (R-PDSO-G5) PLASTIC SMALL-OUTLINE PACKAGE 0,30 0,15 0,65 5 0,10 M 4 1,40 1,10 1 0,13 NOM 2,40 1,80 3 Gage Plane 2,15 1,85 0,15 0°–8° 0,46 0,26 Seating Plane 1,10 0,80 0,10 0,00 0,10 4093553-2/D 01/02 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion. Falls within JEDEC MO-203 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Amplifiers Applications amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security Telephony www.ti.com/telephony Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2003, Texas Instruments Incorporated