TI CD74HCT4051QM96Q1

SCLS569A − JANUARY 2004 − FEBRUARY 2004
D Qualification in Accordance With
D
D
D
D
D
D
D
D
AEC-Q100†
Qualified for Automotive Applications
Customer-Specific Configuration Control
Can Be Supported Along With
Major-Change Approval
Wide Analog Input Voltage Range:
+5 V Max
Low ON Resistance
− 70 W Typical (VCC − VEE = 4.5 V)
− 40 W Typical (VCC − VEE = 9 V)
Low Crosstalk Between Switches
Fast Switching and Propagation Speeds
Break-Before-Make Switching
Wide Operating Temperature Range: −405C
to 1255C
† Contact factory for details. Q100 qualification data available on
request.
D Operation Control Voltage: 4.5 V to 5.5 V
D Switch Voltage: 0 V to 10 V
D Direct LSTTL Input Logic Compatibility:
D
VIL = 0.8 V Max, VIH = 2 V Min
CMOS Input Compatibility: II v 1 mA at VOL,
VOH
M PACKAGE
(TOP VIEW)
A4
A6
COM OUT/IN A
A7
A5
E
VEE
GND
1
16
2
15
3
14
4
13
5
12
6
11
7
10
8
9
VCC
A2
A1
A0
A3
S0
S1
S2
description/ordering information
This device is a digitally controlled analog switch that utilizes silicon-gate CMOS technology to achieve
operating speeds similar to LSTTL, with the low power consumption of standard CMOS integrated circuits.
This analog multiplexer/demultiplexer controls analog voltages that may vary across the voltage supply range
(i.e., VCC to VEE ). It is a bidirectional switch that allows any analog input to be used as an output and vice-versa.
The switch has low ON resistance and low OFF leakages. In addition, this device has an enable control that,
when high, disables all switches to their OFF state.
ORDERING INFORMATION
TA
PACKAGE‡
ORDERABLE
PART NUMBER§
TOP-SIDE
MARKING
−40°C to 125°C
SOIC − M
Reel of 2500
CD74HCT4051QM96Q1
HCT4051Q
‡ Package drawings, standard packing quantities, thermal data, symbolization, and PCB design
guidelines are available at www.ti.com/sc/package.
§ The suffix 96 denotes tape and reel.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright  2004, Texas Instruments Incorporated
!" # $%&" !# '%()$!" *!"&+
*%$"# $ " #'&$$!"# '& ",& "&# &-!# #"%&"#
#"!*!* .!!"/+ *%$" '$&##0 *&# " &$&##!)/ $)%*&
"&#"0 !)) '!!&"&#+
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
SCLS569A − JANUARY 2004 − FEBRUARY 2004
FUNCTION TABLE
INPUTS
ON CHANNELS
ENABLE
S2
S1
S0
L
L
L
L
A0
L
L
L
H
A1
L
L
H
L
A2
L
L
H
H
A3
L
H
L
L
A4
L
H
L
H
A5
L
H
H
L
A6
L
H
H
H
A7
H
X
X
X
None
X = Don’t care
logic diagram (positive logic)
Channel In/Out
VCC
A7
16
4
A6
2
A5
5
A4
1
A3 A2 A1 A0
12 15 14 13
TG
TG
S0
11
Address Select
TG
S1
10
Logic
Level
Conversion
S2
TG
Binary
to
1 of 8
Decoder
With
Enable
9
3
TG
TG
TG
E
8
TG
8
GND
2
7
VCC
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
COM
OUT/IN
A
SCLS569A − JANUARY 2004 − FEBRUARY 2004
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage range: VCC − VEE (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 10.5 V
VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to +7 V
VEE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5 V to −7 V
Input clamp current, IIK (VI < −0.5 V or VI > VCC + 0.5 V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20 mA
Output clamp current, IOK (VO < VEE − 0.5 V or VO > VCC + 0.5 V) . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20 mA
Switch current (VI > VEE − 0.5 V or VI < VCC + 0.5 V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±25 mA
Continuous current through VCC or GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±50 mA
VEE current, IEE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −20 mA
Package thermal impedance, θJA (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73°C/W
Maximum junction temperature, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150°C
Lead temperature (during soldering):
At distance 1/16 ± 1/32 inch (1,59 ± 0,79 mm) from case for 10 s max . . . . . . . . . . . . . . . . . . . . . . . 300°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltages referenced to GND unless otherwise specified.
2. The package thermal impedance is calculated in accordance with JESD 51-7.
recommended operating conditions (see Note 3)
VCC
Supply voltage
MIN
MAX
UNIT
4.5
5.5
V
Supply voltage, VCC − VEE (see Figure 1)
2
10
V
VEE
VIH
Supply voltage (see Note 4 and Figure 2)
0
−6
V
High-level input voltage
2
VIL
VI
Low-level input voltage
VIS
tt
Analog switch I/O voltage
Input control voltage
0
Input transition (rise and fall) time
VCC = 4.5 V
VEE
0
V
0.8
V
VCC
VCC
V
500
ns
V
TA
Operating free-air temperature
−40
125
°C
NOTES: 3. All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report,
Implications of Slow or Floating CMOS Inputs, literature number SCBA004.
4. In certain applications, the external load resistor current may include both VCC and signal-line components. To avoid drawing VCC
current when switch current flows into the transmission gate inputs, the voltage drop across the bidirectional switch must not exceed
0.6 V (calculated from ron values shown in electrical characteristics table). No VCC current flows through RL if the switch current flows
into the COM OUT/IN A terminal.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
SCLS569A − JANUARY 2004 − FEBRUARY 2004
recommended operating area as a function of supply voltages
8
(VCC – GND) – V
(VCC – GND) – V
8
6
HCT
HC
4
2
6
HCT
HC
4
2
0
0
0
2
4
6
8
10
0
12
−2
(VCC – VEE) – V
−4
−6
−8
(VEE – GND) – V
Figure 2
Figure 1
electrical characteristics over recommended operating free-air temperature range (unless
otherwise noted)
PARAMETER
TEST CONDITIONS
VEE
MIN
ron
VIS = VCC or VEE
IO = 1 mA,
VI = VIH or VIL,
See Figure 9
VIS = VCC to VEE
∆ron
Between any two channels
IIZ
For switch OFF:
When VIS = VCC, VOS = VEE;
When VIS = VEE, VOS = VCC
For switch ON:
All applicable combinations of VIS and VOS
voltage levels,
VI = VIH or VIL
IIL
ICC
∆ICC
VI = VCC or GND
IO = 0,
VI = VCC or GND
TYP
MAX
MIN
0V
4.5 V
70
160
240
4.5 V
40
120
180
0V
4.5 V
90
180
270
−4.5 V
4.5 V
45
130
195
0V
4.5 V
10
−4.5 V
4.5 V
5
0V
6V
Ω
±0.2
±2
−5 V
5V
±0.4
±4
5.5 V
±0.1
±1
When VIS = VEE,
VOS = VCC
0V
5.5 V
8
160
When VIS = VCC,
VOS = VEE
−4.5 V
5.5 V
16
320
360
490
µA
A
µA
4.5 V
to
5.5 V
Per input pin: 1 unit load,
See Note 5, VIN = VCC − 2.1 V
HCT input loading
INPUT
UNIT LOADS†
4051
All
0.5
† Unit load is ∆ICC limit specified in the electrical
characteristics table, e.g., 360 µA max at 25°C.
POST OFFICE BOX 655303
Ω
A
µA
Control input
TYPE
UNIT
MAX
−4.5 V
100
NOTE 5: For dual-supply systems, theoretical worst case (VI = 2.4 V, VCC = 5.5 V) specification is 1.8 mA.
4
TA = −40°C
TO 125°C
TA = 25°C
VCC
• DALLAS, TEXAS 75265
µA
SCLS569A − JANUARY 2004 − FEBRUARY 2004
switching characteristics over recommended operating free-air temperature range (unless
otherwise noted) (see Figure 8)
PARAMETER
FROM
(INPUT)
TO
(OUTPUT)
LOAD
CAPACITANCE
VEE
MIN
CL = 15 pF
tpd
IN
OUT
5V
S or E
OUT
CI
S or E
OUT
MAX
MIN
UNIT
MAX
4
0V
4.5 V
12
18
CL = 50 pF
−4.5 V
4.5 V
8
12
5V
0V
4.5 V
55
83
CL = 50 pF
−4.5 V
4.5 V
39
59
5V
ns
23
CL = 50 pF
CL = 15 pF
tdis
TYP
CL = 50 pF
CL = 15 pF
ten
TA = −40°C
TO 125°C
TA = 25°C
VCC
ns
19
CL = 50 pF
0V
4.5 V
45
68
CL = 50 pF
−4.5 V
4.5 V
32
48
10
10
Control
ns
pF
operating characteristics, VCC = 5 V, TA = 25°C, input tr, tf = 6 ns
PARAMETER
Cpd
TYP
Power dissipation capacitance (see Note 6)
52
UNIT
pF
NOTE 6: Cpd is used to determine the dynamic power consumption (PD), per package.
PD = (Cpd × VCC2 × fI) + Σ (CL + CS) VCC2 × fO
fO = output frequency
fI = input frequency
CL = output load capacitance
CS = switch capacitance
VCC = supply voltage
analog channel characteristics, TA = 25°C
PARAMETER
TEST CONDITIONS
CI
Switch input capacitance
CCOM
Common output capacitance
fmax
Minimum switch frequency
response at −3 dB
See Figure 3 and Figure 10 and
Notes 7 and 8
Sine-wave distortion
See Figure 5
E or address select (S0, S1, S2) to
switch feedthrough noise
See Figure 6 and Notes 8 and 9
Switch OFF signal feedthrough
See Figure 7 and Figure 11 and
Notes 8 and 9
VEE
VCC
TYP
UNIT
5
pF
25
pF
−2.25 V
2.25 V
145
−4.5 V
4.5 V
180
−2.25 V
2.25 V
0.035
−4.5 V
4.5 V
0.018
−2.25 V
2.25 V
TBE
−4.5 V
4.5 V
TBE
−2.25 V
2.25 V
−73
−4.5 V
4.5 V
−75
MHz
%
mV
dB
NOTES: 7. Adjust input voltage to obtain 0 dBm at VOS for fIN = 1 MHz.
8. VIS is centered at (VCC − VEE)/2.
9. Adjust input for 0 dBm.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
SCLS569A − JANUARY 2004 − FEBRUARY 2004
PARAMETER MEASUREMENT INFORMATION
VCC
VIS
R
SWITCH
ON
VOS1
0.1 mF
INPUT
R
fIS = 1-MHz Sine Wave
R = 50 W
C = 10 pF
VCC/2
VCC
VCC
R
VOS
SWITCH
ON
VIS
C
0.1 mF
50 Ω
dB
METER
10 pF
VOS2
SWITCH
OFF
VCC/2
dB
METER
C
R
VCC/2
VCC/2
Figure 4. Crosstalk Between Two Switches
Test Circuit
Figure 3. Frequency-Response Test Circuit
E
VCC
V P−P
VCC
V OS
Sine
Wave
VIS
SWITCH
ON
VOS
10 mF
10k Ω
50 pF
SWITCH
ALTERNATING
ON AND OFF
tr, tf ≤ 6 ns
fCONT = 1 MHz
50% DUTY
CYCLE
600 Ω
VIS
VI = VIH
VCC/2
DISTORTION
METER
V OS
600 Ω
50 pF
SCOPE
VCC/2
VCC/2
fIS = 1 kHz to 10 kHz
Figure 5. Sine-Wave Distortion Test Circuit
Figure 6. Control-to-Switch Feedthrough Noise
Test Circuit
fIS ≥ 1-MHz Sine Wave
R = 50 Ω
C = 10 pF
VCC
0.1 µF
SWITCH
V IS
VC = VIL
V OS
OFF
dB
R
R
VCC/2
VCC/2
C
METER
Figure 7. Switch OFF Signal Feedthrough Test Circuit
6
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SCLS569A − JANUARY 2004 − FEBRUARY 2004
PARAMETER MEASUREMENT INFORMATION
VCC
Test
Point
From Output
Under Test
PARAMETER
S1
ten
RL = 1 kΩ
tdis
CL
(see Note A)
S2
S1
S2
tPZH
Open
Closed
tPZL
Closed
Open
tPHZ
Open
Closed
tPLZ
Closed
Open
Open
Open
tpd
VEE
LOAD CIRCUIT
Input
50% VCC
50% VCC
tPLH
tPHL
VCC
VEE
In-Phase
Output
50%
10%
90%
90%
tr
tPHL
Out-of-Phase
Output
90%
VOH
50% VCC
10%
VOL
tf
50% VCC
10%
tf
50%
10%
tr
VOLTAGE WAVEFORMS
PROPAGATION DELAY AND OUTPUT TRANSITION TIMES
1.3 V
0V
tPLZ
≈VCC
Output
Waveform 1
(see Note B)
50% VCC
Output
Waveform 2
(see Note B)
10%
VOL
tPHZ
tPZH
VOH
VOL
1.3 V
tPZL
tPLH
90%
3V
Output
Control
50% VCC
90%
VOH
≈0 V
VOLTAGE WAVEFORMS
OUTPUT ENABLE AND DISABLE TIMES
NOTES: A. CL includes probe and test-fixture capacitance.
B. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control.
C. Phase relationships between waveforms were chosen arbitrarily. All input pulses are supplied by generators having the following
characteristics: PRR ≤ 1 MHz, ZO = 50 Ω, tr = 6 ns, tf = 6 ns.
D. For clock inputs, fmax is measured with the input duty cycle at 50%.
E. The outputs are measured one at a time, with one input transition per measurement.
F. tPLZ and tPHZ are the same as tdis.
G. tPZL and tPZH are the same as ten.
H. tPLH and tPHL are the same as tpd.
Figure 8. Load Circuit and Voltage Waveforms
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
7
SCLS569A − JANUARY 2004 − FEBRUARY 2004
TYPICAL CHARACTERISTICS
120
ON Resistance − Ω
100
80
VCC − VEE = 4.5 V
60
VCC − VEE = 6 V
40
VCC − VEE = 9 V
20
1
2
3
4
5
6
7
8
9
Input Signal Voltage − V
Figure 9. Typical ON Resistance vs Input Signal Voltage
0
0
VCC = 4.5 V
GND = −4.5 V
VEE = −4.5 V
RL = 50 Ω
Pin 12 to 3
−4
−20
−40
dB
VCC = 2.25 V
GND = −2.25 V
VEE = −2.25 V
RL = 50 Ω
Pin 12 to 3
−6
−60
VCC = 4.5 V
GND = −4.5 V
VEE = −4.5 V
RL = 50 Ω
Pin 12 to 3
−80
−8
−10
10K
VCC = 2.25 V
GND = −2.25 V
VEE = −2.25 V
RL = 50 Ω
Pin 12 to 3
dB
−2
100K
1M
10M
100M
−100
10K
100K
Frequency − Hz
10M
100M
Frequency − Hz
Figure 10. Channel ON Bandwidth
8
1M
POST OFFICE BOX 655303
Figure 11. Channel OFF Feedthrough
• DALLAS, TEXAS 75265
PACKAGE OPTION ADDENDUM
www.ti.com
18-Jul-2006
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
CD74HCT4051QM96Q1
ACTIVE
SOIC
D
Pins Package Eco Plan (2)
Qty
16
2500
Pb-Free
(RoHS)
Lead/Ball Finish
MSL Peak Temp (3)
CU NIPDAU
Level-2-250C-1 YEAR/
Level-1-235C-UNLIM
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
Low Power Wireless www.ti.com/lpw
Mailing Address:
Telephony
www.ti.com/telephony
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright  2006, Texas Instruments Incorporated