LMV2011 www.ti.com SNOSA32C – AUGUST 2003 – REVISED MARCH 2013 LMV2011 High Precision, Rail-to-Rail Output Operational Amplifier Check for Samples: LMV2011 FEATURES DESCRIPTION • • • • • • • • • • • The LMV2011 is a new precision amplifier that offers unprecedented accuracy and stability at an affordable price and is offered in a miniature (5-pin SOT-23) package and in an 8-lead SOIC package. This device utilizes patented techniques to measure and continually correct the input offset error voltage. The result is an amplifier which is ultra stable over time and temperature. It has excellent CMRR and PSRR ratings, and does not exhibit the familiar 1/f voltage and current noise increase that plagues traditional amplifiers. The combination of the LMV2011 characteristics makes it a good choice for transducer amplifiers, high gain configurations, ADC buffer amplifiers, DAC I-V conversion, and any other 2.7V5V application requiring precision and long term stability. 1 2 (For Vs = 5V, Typical Unless Otherwise Noted) Low Ensured Vos Over Temperature 35µV Low Noise with no 1/f 35nV/√Hz High CMRR 130dB High PSRR 120dB High AVOL 130dB Wide Gain-Bandwidth Product 3MHz High Slew Rate 4V/µs Low Supply Current 930µA Rail-to-Rail Output 30mV No External Capacitors Required APPLICATIONS • • • Precision Instrumentation Amplifiers Thermocouple Amplifiers Strain Gauge Bridge Amplifier Other useful benefits of the LMV2011 are rail-to-rail output, a low supply current of 930µA, and wide gainbandwidth product of 3MHz. These extremely versatile features found in the LMV2011 provide high performance and ease of use. Connection Diagrams N/C - 2 + 3 - 4 VIN VIN V Figure 1. 5-Pin SOT-23 (Top View) See DBV Package 1 8 - 7 + 6 5 N/C + V VOUT N/C Figure 2. 8-Pin SOIC (Top View) See D Package These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2003–2013, Texas Instruments Incorporated LMV2011 SNOSA32C – AUGUST 2003 – REVISED MARCH 2013 www.ti.com Absolute Maximum Ratings (1) (2) Human Body Model ESD Tolerance 2000V Machine Model 200V Supply Voltage 5.5V −0.3≤ VCM ≤ VCC +0.3V Common-Mode Input Voltage Differential Input Voltage ± Supply Voltage Current At Input Pin 30mA Current At Output Pin 30mA Current At Power Supply Pin 50mA Junction Temperature (TJ) 150°C Lead Temperature (soldering 10 sec.) (1) (2) +300°C Absolute Maximum Ratings indicate limits beyond which damage may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but specific performance is not ensured. For ensured specifications and test conditions, see the Electrical Characteristics. If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and specifications. Operating Ratings (1) Supply Voltage 2.7V to 5.25V −65°C to 150°C Storage Temperature Range Operating Temperature Range (1) 0°C to 70°C Absolute Maximum Ratings indicate limits beyond which damage may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but specific performance is not ensured. For ensured specifications and test conditions, see the Electrical Characteristics. 2.7V DC Electrical Characteristics Unless otherwise specified, all limits ensured for T J = 25°C, V+ = 2.7V, V-= 0V, V CM = 1.35V, VO = 1.35V and RL > 1MΩ. Boldface limits apply at the temperature extremes. Symbol VOS Parameter Conditions Min Input Offset Voltage Offset Calibration Time TCVOS Typ Max Units 0.8 25 35 μV 0.5 10 12 ms Input Offset Voltage 0.015 μV/°C Long-Term Offset Drift 0.006 μV/month 2.5 Input Current -3 IOS Input Offset Current 6 pA RIND Input Differential Resistance 9 MΩ CMRR PSRR pA Common Mode Rejection Ratio −0.3 ≤ VCM ≤ 0.9V 0 ≤ VCM ≤ 0.9V 130 95 90 dB Power Supply Rejection Ratio 2.7V ≤ V+ ≤ 5V 120 95 90 dB 130 95 90 124 90 85 AVOL RL = 10kΩ Open Loop Voltage Gain RL = 2kΩ VO RL = 10kΩ to 1.35V VIN(diff) = ±0.5V Output Swing RL = 2kΩ to 1.35V VIN(diff) = ±0.5V 2 5 μV Lifetime VOS Drift IIN 2.665 2.655 2.68 0.033 2.630 2.615 Submit Documentation Feedback dB 0.060 0.075 V 2.65 0.061 0.085 0.105 V Copyright © 2003–2013, Texas Instruments Incorporated Product Folder Links: LMV2011 LMV2011 www.ti.com SNOSA32C – AUGUST 2003 – REVISED MARCH 2013 2.7V DC Electrical Characteristics (continued) Unless otherwise specified, all limits ensured for T J = 25°C, V+ = 2.7V, V-= 0V, V CM = 1.35V, VO = 1.35V and RL > 1MΩ. Boldface limits apply at the temperature extremes. Symbol Parameter IO Output Current ROUT Output Impedance IS Supply Current Typ Max Sourcing, VO = 0V VIN(diff) = ±0.5V Conditions Min 12 5 3 Sinking, VO = 5V V IN(diff) = ±0.5V 18 5 3 Units mA Ω 0.05 0.919 1.20 1.50 mA 2.7V AC Electrical Characteristics TJ = 25°C, V+ = 2.7V, V -= 0V, VCM = 1.35V, VO = 1.35V, and RL > 1MΩ. Boldface limits apply at the temperature extremes. Symbol Parameter Conditions Min Typ Max Units GBW Gain-Bandwidth Product 3 MHz SR Slew Rate 4 V/μs θm Phase Margin 60 Deg Gm Gain Margin −14 dB en Input-Referred Voltage Noise 35 nV/√Hz in Input-Referred Current Noise 150 fA/√Hz enp-p Input-Referred Voltage Noise 850 nVpp trec Input Overload Recovery Time 50 ms RS = 100Ω, DC to 10Hz ts 1% AV = −1, RL = 2kΩ 1V Step Output Settling Time 0.9 0.1% 49 0.01% 100 μs 5V DC Electrical Characteristics Unless otherwise specified, all limits ensured for T J = 25°C, V+ = 5V, V-= 0V, V CM = 2.5V, VO = 2.5V and RL > 1MΩ. Boldface limits apply at the temperature extremes. Symbol VOS Parameter Conditions Min Input Offset Voltage Offset Calibration Time TCVOS Typ Max Units 0.12 25 35 μV 0.5 10 12 ms Input Offset Voltage 0.015 μV/°C Long-Term Offset Drift 0.006 μV/month 2.5 Input Current -3 IOS Input Offset Current 6 pA RIND Input Differential Resistance 9 MΩ CMRR PSRR 5 μV Lifetime VOS Drift IIN pA Common Mode Rejection Ratio −0.3 ≤ VCM ≤ 3.2 0 ≤ VCM ≤ 3.2 130 100 90 dB Power Supply Rejection Ratio 2.7V ≤ V+ ≤ 5V 120 95 90 dB 130 105 100 132 95 90 AVOL RL = 10kΩ Open Loop Voltage Gain RL = 2kΩ dB Submit Documentation Feedback Copyright © 2003–2013, Texas Instruments Incorporated Product Folder Links: LMV2011 3 LMV2011 SNOSA32C – AUGUST 2003 – REVISED MARCH 2013 www.ti.com 5V DC Electrical Characteristics (continued) Unless otherwise specified, all limits ensured for T J = 25°C, V+ = 5V, V-= 0V, V CM = 2.5V, VO = 2.5V and RL > 1MΩ. Boldface limits apply at the temperature extremes. Symbol Parameter Conditions VO RL = 10kΩ to 2.5V VIN(diff) = ±0.5V Output Swing RL = 2kΩ to 2.5V VIN(diff) = ±0.5V IO Output Current ROUT Min Typ 4.96 4.95 4.978 0.040 4.895 4.875 0.070 0.085 Units V 4.919 0.091 0.115 0.140 Sourcing, VO = 0V VIN(diff) = ±0.5V 15 8 6 Sinking, VO = 5V V IN(diff) = ±0.5V 17 8 6 Output Impedance IS Max mA Ω 0.05 0.930 Supply Current per Channel V 1.20 1.50 mA 5V AC Electrical Characteristics TJ = 25°C, V+ = 5V, V -= 0V, VCM = 2.5V, VO = 2.5V, and RL > 1MΩ. Boldface limits apply at the temperature extremes. Symbol Parameter Conditions Min Typ Max Units GBW Gain-Bandwidth Product 3 MHz SR Slew Rate 4 V/μs θm Phase Margin 60 deg Gm Gain Margin −15 dB en Input-Referred Voltage Noise 35 nV/√Hz in Input-Referred Current Noise 150 fA/√Hz enp-p Input-Referred Voltage Noise 850 nVpp trec Input Overload Recovery Time 50 ms RS = 100Ω, DC to 10Hz ts 1% Output Settling Time 4 AV = −1, RL = 2kΩ 1V Step 0.8 0.1% 36 0.01% 100 Submit Documentation Feedback us Copyright © 2003–2013, Texas Instruments Incorporated Product Folder Links: LMV2011 LMV2011 www.ti.com SNOSA32C – AUGUST 2003 – REVISED MARCH 2013 Typical Performance Characteristics TA=25C, VS= 5V unless otherwise specified. Supply Current vs. Supply Voltage Offset Voltage vs. Supply Voltage 5 1.20 4 0°C 70°C 1.10 1.05 1.00 0.95 3 OFFSET VOLTAGE (PV) SUPPLY CURRENT (mA) 1.15 25°C 0.90 0.85 2 1 70°C 0 -1 -2 -3 0°C -4 -5 0.80 2.5 3 3.5 4.5 4 5 2.5 5.5 3 Figure 3. Offset Voltage vs. Common Mode 5.5 5 Offset Voltage vs. Common Mode 10 0°C 8 25°C 6 4 70°C 2 0 -2 -4 -6 25°C 6 4 70°C 2 0 -2 -4 -6 -8 VS = 2.7V -10 -0.2 0°C 8 OFFSET VOLTAGE (PV) OFFSET VOLTAGE (PV) 4.5 Figure 4. 10 0.3 0.8 1.3 1.8 VS = 5V -10 -0.2 2.3 0.8 1.8 2.8 3.8 COMMON MODE VOLTAGE (V) COMMON MODE VOLTAGE (V) Figure 5. Figure 6. Voltage Noise vs. Frequency 4.8 Input Bias Current vs. Common Mode 500 10000 VS = 5V VS = 5V 400 300 BIAS CURRENT (pA) VOLTAGE NOISE (nV/ Hz) 4 3.5 SUPPLY VOLTAGE (V) SUPPLY VOLTAGE (V) -8 25°C 1000 100 200 100 0 -100 -200 -300 -400 10 0.1 1 10 100 1k 10k 100k 1M -500 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 VCM (V) FREQUENCY (Hz) Figure 7. Figure 8. Submit Documentation Feedback Copyright © 2003–2013, Texas Instruments Incorporated Product Folder Links: LMV2011 5 LMV2011 SNOSA32C – AUGUST 2003 – REVISED MARCH 2013 www.ti.com Typical Performance Characteristics (continued) TA=25C, VS= 5V unless otherwise specified. PSRR vs. Frequency PSRR vs. Frequency 120 120 VS = 2.7V 100 80 VCM = 2.5V 100 80 NEGATIVE PSRR (dB) PSRR (dB) VS = 5V VCM = 1V 60 40 NEGATIVE 60 40 POSITIVE POSITIVE 20 20 0 0 10 100 1k 10k 1M 100k 10M 10 1k 100 FREQUENCY (Hz) Figure 9. Output Sourcing @ 2.7V Output Sourcing @ 5V VS = 2.7V 16 14 70°C 12 10 0°C 0°C 8 70°C 6 25°C 4 VS = 5V 18 SOURCING CURRENT (mA) SOURCING CURRENT (mA) 10M 20 18 70°C 16 14 12 0°C 0°C 10 70°C 8 6 25°C 4 2 2 0 0 0 0.5 1 1.5 2 2.5 3 0 1 OUTPUT VOLTAGE (V) 2 3 4 5 OUTPUT VOLTAGE (V) Figure 11. Figure 12. Output Sinking @ 2.7V Output Sinking @ 5V 20 20 0°C 18 18 16 SINKING CURRENT (mA) SINKING CURRENT (mA) 1M 100k Figure 10. 20 14 25°C 12 10 70°C 8 6 4 2 0°C 16 14 12 25°C 10 70°C 8 6 4 2 VS = 2.7V 0 VS = 5V 0 0 0.5 1 1.5 2 2.5 3 OUTPUT VOLTAGE (V) 0 1 2 3 4 5 OUTPUT VOLTAGE (V) Figure 13. 6 10k FREQUENCY (Hz) Figure 14. Submit Documentation Feedback Copyright © 2003–2013, Texas Instruments Incorporated Product Folder Links: LMV2011 LMV2011 www.ti.com SNOSA32C – AUGUST 2003 – REVISED MARCH 2013 Typical Performance Characteristics (continued) TA=25C, VS= 5V unless otherwise specified. Max Output Swing vs. Supply Voltage Max Output Swing vs. Supply Voltage 120 + 100 80 60 40 70°C 25°C RL = 2k: OUTPUT VOLTAGE (mV FROM V ) RL = 10k: + OUTPUT VOLTAGE (mV FROM V ) 120 20 100 80 60 0°C 40 20 0°C 0 2.5 3 3.5 25°C 70°C 0 4 4.5 5 5.5 2.5 3 SUPPLY VOLTAGE (V) 3.5 4.5 5 5.5 SUPPLY VOLTAGE (V) Figure 15. Figure 16. Min Output Swing vs. Supply Voltage Min Output Swing vs. Supply Voltage 120 120 - 100 80 70°C 60 70°C OUTPUT VOLTAGE (mV FROM V ) RL = 10k: - OUTPUT VOLTAGE (mV FROM V ) 4 25°C 40 20 0°C 25°C 100 80 60 0°C 40 20 RL = 2k: 0 0 2.5 3 3.5 4 4.5 5 5.5 2.5 3 SUPPLY VOLTAGE (V) 3.5 4 4.5 5 5.5 SUPPLY VOLTAGE (V) Figure 17. Figure 18. CMRR vs. Frequency Open Loop Gain and Phase vs. Supply Voltage 100 140 150.0 VS = 5V VS = 5V 120 80 120.0 PHASE 80 60 90.0 60.0 40 GAIN PHASE (°) VS = 5V 60 GAIN (dB) CMRR (dB) 100 30.0 20 40 RL = 1M 0 20 0.0 VS = 2.7V CL = < 20pF VS = 2.7V OR 5V -20 0 10 100 100k 1k FREQUENCY (Hz) 100k 100 1k 10k 100k 1M -30.0 10M FREQUENCY (Hz) Figure 19. Figure 20. Submit Documentation Feedback Copyright © 2003–2013, Texas Instruments Incorporated Product Folder Links: LMV2011 7 LMV2011 SNOSA32C – AUGUST 2003 – REVISED MARCH 2013 www.ti.com Typical Performance Characteristics (continued) TA=25C, VS= 5V unless otherwise specified. Open Loop Gain and Phase vs. RL @ 2.7V 100 Open Loop Gain and Phase vs. RL @ 5V 150.0 100 120.0 80 150.0 RL = >1M 80 120.0 PHASE PHASE RL = >1M 40 30.0 VS = 2.7V 20 RL = >1M 0.0 CL = < 20pF RL = >1M & 2k RL = 2k CL = < 20pF -30.0 10M 1M 100 100k 10k 1k FREQUENCY (Hz) Figure 22. Open Loop Gain and Phase vs. CL @ 5V 150.0 100 150.0 10pF 10pF 80 120.0 80 120.0 PHASE PHASE 60.0 40 GAIN 30.0 20 CL = 10,50,200 & 500pF 100k 10k 1k 1M GAIN 0 500pF -20 60.0 500pF 20 0.0 VS = 2.7V, RL = >1M 40 30.0 0.0 VS = 5V, RL = >1M 500pF CL = 10,50,200 & 500pF -20 100 1M 1k 10k 100k FREQUENCY (Hz) -30.0 10M FREQUENCY (Hz) Figure 23. Open Loop Gain and Phase vs. Temperature @ 5V 113 100 113 100 PHASE PHASE 90 0°C 80 90 0°C 0°C 45 20 70°C VS = 2.7V 23 68 60 GAIN (dB) GAIN 70°C PHASE (deg) GAIN (dB) 0°C 68 60 25°C GAIN 40 70°C 20 0 0 CL = <20pF -20 100k 1M -23 10M -20 1k FREQUENCY (Hz) 10k 100k 1M -23 10M FREQUENCY (Hz) Figure 25. 8 23 0 RL = >1M CL = <20pF 10k 70°C VS = 5V VOUT = 200mVPP RL = >1M 1k 45 25°C VOUT = 200mVPP 0 -30.0 10M Figure 24. Open Loop Gain and Phase vs. Temperature @ 2.7V 40 90.0 PHASE (°) 500pF 10pF 60 90.0 GAIN (dB) 10pF PHASE (°) GAIN (dB) 60 80 1M Figure 21. Open Loop Gain and Phase vs. CL @ 2.7V 100 -30.0 10M -20 FREQUENCY (Hz) 100 0 0.0 RL = >1M & 2k 100k 10k 1k 0 RL = 2k -20 100 30.0 VS = 5V RL = >1M 0 60.0 RL = >1M GAIN PHASE (deg) 20 60.0 90.0 PHASE (°) RL = >1M GAIN (dB) GAIN (dB) GAIN 40 60 90.0 PHASE (°) RL = 2k 60 Figure 26. Submit Documentation Feedback Copyright © 2003–2013, Texas Instruments Incorporated Product Folder Links: LMV2011 LMV2011 www.ti.com SNOSA32C – AUGUST 2003 – REVISED MARCH 2013 Typical Performance Characteristics (continued) TA=25C, VS= 5V unless otherwise specified. THD+N vs. AMPL THD+N vs. Frequency 10 10 MEAS FREQ = 1 KHz MEAS BW = 22 KHz VOUT = 2 VPP MEAS BW = 500 kHz RL = 10k RL = 10k 1 AV = +10 1 THD+N (%) THD+N (%) AV = +10 VS = 2.7V 0.1 VS = 2.7V VS = 5V 0.1 VS = 5V VS = 5V VS = 2.7V 0.01 0.1 0.01 1 10 10 100 1k 10k OUTPUT VOLTAGE (VPP) FREQUENCY (Hz) Figure 27. Figure 28. 100k NOISE (200 nV/DIV) 0.1Hz − 10Hz Noise vs. Time 1 sec/DIV Figure 29. Submit Documentation Feedback Copyright © 2003–2013, Texas Instruments Incorporated Product Folder Links: LMV2011 9 LMV2011 SNOSA32C – AUGUST 2003 – REVISED MARCH 2013 www.ti.com APPLICATION INFORMATION THE BENEFITS OF LMV2011 NO 1/f NOISE Using patented methods, the LMV2011 eliminates the 1/f noise present in other amplifiers. That noise, which increases as frequency decreases, is a major source of measurement error in all DC-coupled measurements. Low-frequency noise appears as a constantly-changing signal in series with any measurement being made. As a result, even when the measurement is made rapidly, this constantly-changing noise signal will corrupt the result. The value of this noise signal can be surprisingly large. For example: If a conventional amplifier has a flat-band noise level of 10nV/√Hz and a noise corner of 10Hz, the RMS noise at 0.001Hz is 1µV/√Hz. This is equivalent to a 0.50µV peak-to-peak error, in the frequency range 0.001 Hz to 1.0 Hz. In a circuit with a gain of 1000, this produces a 0.50mV peak-to-peak output error. This number of 0.001 Hz might appear unreasonably low, but when a data acquisition system is operating for 17 minutes, it has been on long enough to include this error. In this same time, the LMV2011 will only have a 0.21mV output error. This is smaller by 2.4 x. Keep in mind that this 1/f error gets even larger at lower frequencies. At the extreme, many people try to reduce this error by integrating or taking several samples of the same signal. This is also doomed to failure because the 1/f nature of this noise means that taking longer samples just moves the measurement into lower frequencies where the noise level is even higher. The LMV2011 eliminates this source of error. The noise level is constant with frequency so that reducing the bandwidth reduces the errors caused by noise. Another source of error that is rarely mentioned is the error voltage caused by the inadvertent thermocouples created when the common "Kovar type" IC package lead materials are soldered to a copper printed circuit board. These steel-based leadframe materials can produce over 35μV/°C when soldered onto a copper trace. This can result in thermocouple noise that is equal to the LMV2011 noise when there is a temperature difference of only 0.0014°C between the lead and the board! For this reason, the lead-frame of the LMV2011 is made of copper. This results in equal and opposite junctions which cancel this effect. The extremely small size of the SOT-23 package results in the leads being very close together. This further reduces the probability of temperature differences and hence decreases thermal noise. OVERLOAD RECOVERY The LMV2011 recovers from input overload much faster than most chopper-stabilized opamps. Recovery from driving the amplifier to 2X the full scale output, only requires about 40ms. Many chopper-stabilized amplifiers will take from 250ms to several seconds to recover from this same overload. This is because large capacitors are used to store the unadjusted offset voltage. Figure 30. Overload Recovery Test The wide bandwidth of the LMV2011 enhances performance when it is used as an amplifier to drive loads that inject transients back into the output. ADCs (Analog-to-Digital Converters) and multiplexers are examples of this type of load. To simulate this type of load, a pulse generator producing a 1V peak square wave was connected to the output through a 10pF capacitor (Figure 30). The typical time for the output to recover to 1% of the applied pulse is 80ns. To recover to 0.1% requires 860ns. This rapid recovery is due to the wide bandwidth of the output stage and large total GBW. NO EXTERNAL CAPACITORS REQUIRED The LMV2011 does not need external capacitors. This eliminates the problems caused by capacitor leakage and dielectric absorption, which can cause delays of several seconds from turn-on until the amplifier's error has settled. 10 Submit Documentation Feedback Copyright © 2003–2013, Texas Instruments Incorporated Product Folder Links: LMV2011 LMV2011 www.ti.com SNOSA32C – AUGUST 2003 – REVISED MARCH 2013 MORE BENEFITS The LMV2011 offers the benefits mentioned above and more. It has a rail-to-rail output and consumes only 950µA of supply current while providing excellent DC and AC electrical performance. In DC performance, the LMC2001 achieves 130dB of CMRR, 120dB of PSRR and 130dB of open loop gain. In AC performance, the LMV2011 provides 3MHz of gain-bandwidth product and 4V/µs of slew rate. HOW THE LMV2011 WORKS The LMV2011 uses new, patented techniques to achieve the high DC accuracy traditionally associated with chopper-stabilized amplifiers without the major drawbacks produced by chopping. The LMV2011 continuously monitors the input offset and corrects this error. The conventional chopping process produces many mixing products, both sums and differences, between the chopping frequency and the incoming signal frequency. This mixing causes large amounts of distortion, particularly when the signal frequency approaches the chopping frequency. Even without an incoming signal, the chopper harmonics mix with each other to produce even more trash. If this sounds unlikely or difficult to understand, look at the plot (Figure 31), of the output of a typical (MAX432) chopper-stabilized opamp. This is the output when there is no incoming signal, just the amplifier in a gain of -10 with the input grounded. The chopper is operating at about 150Hz; the rest is mixing products. Add an input signal and the noise gets much worse. Compare this plot with Figure 32 of the LMV2011. This data was taken under the exact same conditions. The auto-zero action is visible at about 30kHz but note the absence of mixing products at other frequencies. As a result, the LMV2011 has very low distortion of 0.02% and very low mixing products. Figure 31. The Output of a Chopper Stabilized Op Amp (MAX432) 10000 VOLTAGE NOISE (nV/ Hz) VS = 5V 1000 100 10 0.1 1 10 100 1k 10k 100k 1M FREQUENCY (Hz) Figure 32. The Output of the LMV2011 Submit Documentation Feedback Copyright © 2003–2013, Texas Instruments Incorporated Product Folder Links: LMV2011 11 LMV2011 SNOSA32C – AUGUST 2003 – REVISED MARCH 2013 www.ti.com INPUT CURRENTS The LMV2011's input currents are different than standard bipolar or CMOS input currents in that it appears as a current flowing in one input and out the other. Under most operating conditions, these currents are in the picoamp level and will have little or no effect in most circuits. These currents tend to increase slightly when the common-mode voltage is near the minus supply (See the Typical Performance Characteristics). At high temperatures such as 85°C, the input currents become larger, 0.5nA typical, and are both positive except when the VCM is near V−. If operation is expected at low common-mode voltages and high temperature, do not add resistance in series with the inputs to balance the impedances. Doing this can cause an increase in offset voltage. A small resistance such as 1kΩ can provide some protection against very large transients or overloads, and will not increase the offset significantly. PRECISION STRAIN-GAUGE AMPLIFIER This Strain-Gauge amplifier (Figure 32) provides high gain (1006 or ~60 dB) with very low offset and drift. Using the resistors' tolerances as shown, the worst case CMRR will be greater than 108 dB. The CMRR is directly related to the resistor mismatch. The rejection of common-mode error, at the output, is independent of the differential gain, which is set by R3. The CMRR is further improved, if the resistor ratio matching is improved, by specifying tighter-tolerance resistors, or by trimming. Figure 33. Precision Strain Gauge Amplifier Extending Supply Voltages and Output Swing by Using a Composite Amplifier Configuration: In cases where substantially higher output swing is required with higher supply voltages, arrangements like the ones shown in Figure 34 and Figure 35 could be used. These configurations utilize the excellent DC performance of the LMV2011 while at the same time allow the superior voltage and frequency capabilities of the LM6171 to set the dynamic performance of the overall amplifier. For example, it is possible to achieve ±12V output swing with 300MHz of overall GBW (AV = 100) while keeping the worst case output shift due to VOS less than 4mV. The LMV2011 output voltage is kept at about mid-point of its overall supply voltage, and its input common mode voltage range allows the V- terminal to be grounded in one case (Figure 34, inverting operation) and tied to a small non-critical negative bias in another (Figure 35, non-inverting operation). Higher closed-loop gains are also possible with a corresponding reduction in realizable bandwidth. Table 1 shows some other closed loop gain possibilities along with the measured performance in each case. 12 Submit Documentation Feedback Copyright © 2003–2013, Texas Instruments Incorporated Product Folder Links: LMV2011 LMV2011 www.ti.com SNOSA32C – AUGUST 2003 – REVISED MARCH 2013 Figure 34. Composite Amplifier Configuration Table 1. Composite Amplifier Measured Performance AV R1 (Ω) R2 (Ω) C2 (pF) BW (MHz) SR (V/μs) en p-p (mVPP) 50 200 10k 8 3.3 178 37 100 100 10k 10 2.5 174 70 100 1k 100k 0.67 3.1 170 70 500 200 100k 1.75 1.4 96 250 1000 100 100k 2.2 0.98 64 400 In terms of the measured output peak-to-peak noise, the following relationship holds between output noise voltage, en p-p, for different closed-loop gain, AV, settings, where −3dB Bandwidth is BW: (1) Figure 35. Composite Amplifier Configuration It should be kept in mind that in order to minimize the output noise voltage for a given closed-loop gain setting, one could minimize the overall bandwidth. As can be seen from Equation 1 above, the output noise has a square-root relationship to the Bandwidth. Submit Documentation Feedback Copyright © 2003–2013, Texas Instruments Incorporated Product Folder Links: LMV2011 13 LMV2011 SNOSA32C – AUGUST 2003 – REVISED MARCH 2013 www.ti.com In the case of the inverting configuration, it is also possible to increase the input impedance of the overall amplifier, by raising the value of R1, without having to increase the feed-back resistor, R2, to impractical values, by utilizing a "Tee" network as feedback. See the LMC6442 data sheet (Application Notes section) for more details on this. Figure 36. AC Coupled ADC Driver LMV2011 AS ADC INPUT AMPLIFIER The LMV2011 is a great choice for an amplifier stage immediately before the input of an ADC (Analog-to-Digital Converter), whether AC or DC coupled. See Figure 36 and Figure 37. This is because of the following important characteristics: A) Very low offset voltage and offset voltage drift over time and temperature allow a high closed-loop gain setting without introducing any short-term or long-term errors. For example, when set to a closed-loop gain of 100 as the analog input amplifier for a 12-bit A/D converter, the overall conversion error over full operation temperature and 30 years life of the part (operating at 50°C) would be less than 5 LSBs. B) Fast large-signal settling time to 0.01% of final value (1.4μs) allows 12 bit accuracy at 100KHZ or more sampling rate. C) No flicker (1/f) noise means unsurpassed data accuracy over any measurement period of time, no matter how long. Consider the following opamp performance, based on a typical low-noise, high-performance commercially-available device, for comparison: Opamp flatband noise = 8nV/√Hz 1/f corner frequency = 100Hz AV = 2000 Measurement time = 100 sec Bandwidth = 2Hz This example will result in about 2.2 mVPP (1.9 LSB) of output noise contribution due to the opamp alone, compared to about 594μVPP (less than 0.5 LSB) when that opamp is replaced with the LMV2011 which has no 1/f contribution. If the measurement time is increased from 100 seconds to 1 hour, the improvement realized by using the LMV2011 would be a factor of about 4.8 times (2.86mVPP compared to 596μV when LMV2011 is used) mainly because the LMV2011 accuracy is not compromised by increasing the observation time. D) Copper leadframe construction minimizes any thermocouple effects which would degrade low level/high gain data conversion application accuracy (see THE BENEFITS OF LMV2011 NO 1/f NOISE). E) Rail-to-Rail output swing maximizes the ADC dynamic range in 5-Volt single-supply converter applications. Below are some typical block diagrams showing the LMV2011 used as an ADC amplifier (Figure 36 and Figure 37). 14 Submit Documentation Feedback Copyright © 2003–2013, Texas Instruments Incorporated Product Folder Links: LMV2011 LMV2011 www.ti.com SNOSA32C – AUGUST 2003 – REVISED MARCH 2013 Figure 37. DC Coupled ADC Driver Submit Documentation Feedback Copyright © 2003–2013, Texas Instruments Incorporated Product Folder Links: LMV2011 15 LMV2011 SNOSA32C – AUGUST 2003 – REVISED MARCH 2013 www.ti.com REVISION HISTORY Changes from Revision B (March 2013) to Revision C • 16 Page Changed layout of National Data Sheet to TI format .......................................................................................................... 15 Submit Documentation Feedback Copyright © 2003–2013, Texas Instruments Incorporated Product Folder Links: LMV2011 PACKAGE OPTION ADDENDUM www.ti.com 11-Apr-2013 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish (2) MSL Peak Temp Op Temp (°C) Top-Side Markings (3) (4) LMV2011MA ACTIVE SOIC D 8 95 TBD Call TI Call TI 0 to 70 LMV20 11MA LMV2011MA/NOPB ACTIVE SOIC D 8 95 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM 0 to 70 LMV20 11MA LMV2011MAX ACTIVE SOIC D 8 2500 TBD Call TI Call TI 0 to 70 LMV20 11MA LMV2011MAX/NOPB ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM 0 to 70 LMV20 11MA LMV2011MF ACTIVE SOT-23 DBV 5 1000 TBD Call TI Call TI 0 to 70 A84A LMV2011MF/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM 0 to 70 A84A LMV2011MFX ACTIVE SOT-23 DBV 5 3000 TBD Call TI Call TI 0 to 70 A84A LMV2011MFX/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM 0 to 70 A84A (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 11-Apr-2013 (4) Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Top-Side Marking for that device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 8-Apr-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device LMV2011MAX Package Package Pins Type Drawing SOIC SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1 LMV2011MAX/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1 LMV2011MF SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LMV2011MF/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LMV2011MFX SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LMV2011MFX/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 8-Apr-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LMV2011MAX SOIC D 8 2500 367.0 367.0 35.0 LMV2011MAX/NOPB SOIC D 8 2500 367.0 367.0 35.0 LMV2011MF SOT-23 DBV 5 1000 210.0 185.0 35.0 LMV2011MF/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LMV2011MFX SOT-23 DBV 5 3000 210.0 185.0 35.0 LMV2011MFX/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2013, Texas Instruments Incorporated