MPM-07S Series C Compact t 1 x 2 IInch h 7W, Single Output AC/DC Power Supplies Key Features: • 7W Output Power • Compact 1 x 2 Inch Case • Universal 85-265 VAC Input • EN60950 Approved • Meets EN55022 B • Meets IEC Safety Class II • >280 kHour MTBF Electrical Specifications Specifications typical @ +25°C, 230 VAC input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Input Parameter Input Voltage Range Input Frequency Input Current Inrush Current EMI Safety Ground Leakage Current Conditions Min. Typ. Max. 85 265 47 440 See Model Selection Guide 115 VAC 10.0 230 VAC 20.0 Meets CISPR Pub. 22/FCC Class B 115 VAC 0.1 230 VAC 0.3 Units VAC Hz Conditions Min. Typ. Max. See Model Selection Guide See Model Selection Guide ±1.0 ±2.0 VIN = Min to Max ±0.5 ±1.0 IO = Min to Max ±0.5 ±1.0 3.3 & 5.0 VDC Output 1.5 1.8 All Other Outputs 0.8 1.0 115 VAC, 60 Hz 15 ±0.02 Zener Diode Clamp 120 Continuous (Autorecovery) Typ. 120% to 180% of Output Power Units A Pk mA Output Parameter Output Voltage Output Current Output Voltage Accuracy Line Regulation Load Regulation Ripple & Noise (20 MHz) Hold-Up Time Temperature Coefficient Over Voltage Protection Short Circuit Protection, Note 3 Overload Protection, Note 4 % % % %VP-P of VO mSec %/°C % of VO General Parameter Isolation Voltage Isolation Test Voltage Isolation Resistance EMI/RFI EMC Compliance MicroPower Direct 292 Page Street Suite D Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: [email protected] W: www.micropowerdirect.com Conditions Input to Output Input to Output, Flash Tested For 60S 500 VDC Conducted Electrostatic Discharge (ESD) RF Field Susceptibility Electrical Fast Transients/Bursts On Mains Surge Switching Frequency Min. 3,000 4,700 100 Typ. Max. Units VAC VAC MΩ EN 55022 Level B IEC/EN 61000-4-2 Level B IEC/EN61000-4-3 IEC/EN 61000-4-4 Level 3 2 kV IEC/EN 61000-4-5 Level 3 1kV/2 kV 100 kHz Environmental Parameter Operating Temperature Range Storage Temperature Range Cooling Humidity Conditions Min. Typ. Max. -25 +25 +71 -40 +85 Free Air Convection (See Derating Curve) RH, Non-condensing 95 Ambient Units °C °C % Physical Case Size Case Material Weight 2.00 x 1.00 x 0.76 Inches (50.8 x 25.4 x 19.3 mm) Non-Conductive Plastic& Fiberglass (UL94-V0) 1.55 Oz (44g) Reliability Specifications Parameter MTBF Safety Standards Safety Approvals Safety Class Conditions Min. Typ. MIL HDBK 217F, 25°C, Gnd Benign 280 IEN 60950, IEC 60950 IEN 60950, IEC 60950 IEC 61140 Class II Max. Units kHours Model Selection Guide Model Number Input Current (A) Output 1 (Vout 1) Current (A) Voltage 115 VAC 230 VAC (VDC) Max. Min. Efficiency (%, Typ) Fuse Capacitive Rating Load Slow-Blow (µF Max) (mA) MPM-07S-03 0.96 0.051 3.3 1.400 0.140 70 2,200 1,500 MPM-07S-05 0.139 0.051 5.0 1.400 0.140 73 2,200 1,500 MPM-07S-12 0.130 0.051 12.0 0.583 0.058 78 1,000 1,500 MPM-07S-15 0.130 0.051 15.0 0.466 0.047 78 1,000 1,500 MPM-07S-24 0.130 0.051 24.0 0.291 0.029 78 680 1,500 Other outputs may be available Contact the factory for details at: [email protected] Derating Curve Notes: 1. Load regulation is measured for an output change of 0% to 100% at nominal input line. 2. Operation at no-load will not damage these units. However, they may not meet all specifications. 3. Output short circuit protection is provided by a “hiccup mode” circuit. The unit recovers automatically when the fault condition is removed. 4. Output overload protection is provided by a fold back current limiting circuit. 5. It is recommended that an external slow blow fuse also be used on the input for protection. See the table above for the correct rating. Mechanical Dimensions Pin Connections MicroPower Direct Pin Function 1 2 3 4 AC-Neutral AC-Line +Vout -Vout Notes: • All dimensio dimensions are typical in inches (mm) • Tolerance x. x.xx = ±0.01 (±0.25) www.micropowerdirect.com 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: [email protected]