MPO-75S Series Single Output, 75W Compact, Open Frame AC/DC Power Supplies Electrical Specifications Key Features: • 75W Output Power Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Input Parameter • Universal 90-264 AC Input Input Voltage Range • EN 60950 Approved Input Frequency Input Filter Input Current • Low Leakage Current • Four Single Output Models • Meets EN 55022 B • >50 kHour MTBF • Compact 4.1 x 2.05 x 1.2” Conditions Min. Typ. Max. 90 264 120 370 47 63 Meets EN 55022 Class B; FCC Class B See Model Selection Guide Cold Start, 115 VAC 20.0 Cold Start, 230 VAC 40.0 264 VAC 3.5 Universal Inrush Current Safety Ground Leakage Current Units VAC VDC Hz A Pk mA Output Parameter Output Voltage/Current Output Voltage Tolerance Line Regulation Load Regulation Ripple & Noise (20 MHz), See Note 1 Hold-Up Time Temperature Coefficient Short Circuit Protection Over Voltage Protection Overload Protection Conditions Min. Typ. See Model Selection Guide ±2.0 Vin = Min to Max ±1.0 Iout = 5% to 100% ±1.0 5V Output 12V Output 15V Output 24V Output 115 VAC 18 ±0.02 Continuous (Autorecovery) See Model Selection Guide See Note 2 130 Max. Units 150 % Conditions Input to Output Input to Ground Output to Ground 500 VDC Max. Units % % % 100 150 200 300 mV P-P mSec %/°C General Parameter Isolation Voltage Isolation resistance Isolation Capacitance EMI/RFI Conducted Electrostatic Discharge (ESD) RF Field Susceptibility Electrical Fast Transients/Bursts On Mains Surge Fixed EMC Compliance Switching Frequency MicroPower Direct Environmental 292 Page Street Suite D Stoughton, MA 02072 USA Parameter Operating Temperature Range Storage Temperature Range Cooling Humidity Physical Size Weight T: (781) 344-8226 F: (781) 344-8481 E: [email protected] W: www.micropowerdirect.com Min. 3,000 1,500 500 Typ. VAC 100 M⍀ 4,700 pF EN 55022; EN 61000-3-2, -3 IEC/EN 61000-4-2, -6, -8, -11 IEC/EN 61000-4-3 IEC/EN 61000-4-4 IEC/EN 61000-4-5 133 kHz Conditions Min. Typ. Max. -25 +25 +70 -40 +85 Free Air Convection (See Derating Curve) RH, Non-condensing 95 Ambient Units °C °C % 4.1 x 2.05 x 1.2 Inches (103.9 x 52.1 x 30.0 mm) 6.77 Oz (0.195 kg) Reliability Specifications Parameter MTBF Safety Standards Vibration Conditions Min. Typ. Max. Units MIL HDBK 217F, 25°C, Gnd Benign 50 kHours UL 1950, EN 60950, IEC 60950 10~500 Hz, 5G 10 min/1 Cycle. Period of 60 min each along X, Y &Z Axis www.micropowerdirect.com www.micropowerdirect.com Model Selection Guide Model Number MPO-75S-05T MPO-75S-12T MPO-75S-15T MPO-75S-24T Input Current (A) 115 VAC 230 VAC 2.0 2.0 2.0 2.0 1.0 1.0 1.0 1.0 Voltage (VDC) 5.0 12.0 15.0 24.0 Output Current (A) Rated % Min. 10.00 6.25 5.00 3.13 1.00 1.00 1.00 1.00 Max Output Power Over Voltage Protection (W) (VDC) 50 75 75 75 6.2 15.0 18.0 28.0 Efficiency (%, Typ) 73 80 80 80 Derating Curve For U-channel and enclosed models, see MPU-75S Datasheet Notes: 1. Output ripple and noise is measured at 20 MHz bandwidth using a 0.1 µF and 47 µF capacitor connected in parallel as close to the power supply terminals as possible. 2. Overload protection is provided by a “hiccup mode” circuit. The unit recovers automatically when the fault condition is removed. 3. Over voltage protection is provided by a zener diode clamp. 4. These units will operate at no load without damage, however, MPD recommends that a minimum 1% load always be used . 5. Each unit includes an input fuse. Since this fuse is not field replaceable, it is recommended that an external fuse be used on the input of the power supply for protection. For these units, a 15A/250V slow blow fuse is recommended. Mechanical Dimensions Pin Connections Pin 1 2 3 MicroPower Direct Function Pin Function AC-Neutral AC-Line AC-Ground 4 5 +VOUT -VOUT Notes: • All dimensions are typical in inches (mm) • Tolerance x.xx = ±0.02 (±0.50) We Power Your Success - For Less! 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: [email protected]