RSG RSG Electronic Components GmbH Sprendlinger Landstr. 115 D-63069 Offenbach/Germany Tel. +49 69 984047-0 Fax +49 69 984047-77 [email protected] www.rsg-electronic.de ■ ■ ELECTRONIC COMPONENTS ■ ■ ■ ■ Änderungen vorbehalten / subject to change without notice QP-200 200W Quad Output with PFC Function series Features : Universal AC input / Full range Built-in active PFC function, PF>0.95 Protections:Short circuit/Over load/Over voltage/Over temperature Forced air cooling by built-in DC fan CH1,2 can be adjustable from -5~+10% With power good and fail signal output(Optional) Built-in remote sense function for CH1,2 100% full load burn-in test CH4 can set to positive after consult us before delivery Fixed switching frequency at PFC:67KHz PWM:134KHz(Optional) 3 years warranty .. SPECIFICATION QP-200D MODEL CH1 CH2 CH3 CH4 CH1 CH2 CH3 CH4 CH1 CH2 CH3 CH4 DC VOLTAGE 5V 12V 24V -12V 5V 15V 24V -15V 5V 3.3V 12V -5V RATED CURRENT 15A 4A 3A 0.7A 15A 3A 3A 0.7A 15A 15A 6A 0.7A CURRENT RANGE 3 ~ 20A 0 ~ 6A 0.4 ~ 5A 0 ~ 1A 3 ~ 20A 0 ~ 5A 0.4 ~ 5A 0 ~ 1A 3 ~ 20A 0 ~ 20A 0.5 ~ 8A 0 ~ 1A RATED POWER 203.4W 20A 8A 1A Note.4 20A 202.5W 7A 6A 1A 20A 200W 6A 6A 1A 20A RIPPLE & NOISE (max.) Note.2 100mVp-p 150mVp-p 150mVp-p 150mVp-p 100mVp-p 150mVp-p 150mVp-p 150mVp-p 100mVp-p 100mVp-p 150mVp-p 150mVp-p CH2: 14.25 ~ 16.5V CH1: 4.75 ~ 5.5V CH2: 3.14 ~ 3.63V VOLTAGE TOLERANCE Note.3 CH1: 4.75 ~ 5.5V 3.0% 3.0% +10,-6% 6.0% 3.0% 3.0% +10,-6% 6.0% 3.0% 3.0% +8,-10% LINE REGULATION 1.0% 1.0% 2.0% 1.0% 1.0% 1.0% 2.0% 1.0% 1.0% 1.0% 2.0% 1.0% LOAD REGULATION 2.0% 2.0% 6.0% 2.0% 2.0% 2.0% 6.0% 2.0% 2.0% 2.0% 6.0% 2.0% VOLTAGE ADJ. RANGE CH2: 11.4 ~ 13.2V SETUP, RISE TIME 800ms, 50ms at full load HOLD TIME (Typ.) 24ms at full load VOLTAGE RANGE INPUT QP-200-3A OUTPUT NUMBER PEAK CURRENT OUTPUT QP-200F Note.6 90 ~ 264VAC FREQUENCY RANGE 47 ~ 63Hz CH1: 4.75 ~ 5.5V 127 ~ 370VDC POWER FACTOR (Typ.) PF>0.95/230VAC EFFICIENCY (Typ.) 75% AC CURRENT (Typ.) INRUSH CURRENT (Typ.) 3.5A/115VAC 2A/230VAC COLD START 30A PF>0.98/115VAC at full load 75% 72% LEAKAGE CURRENT <2mA / 240VAC OVER LOAD 105 ~ 150% rated output power Protection type : Constant current limiting, recovers automatically after fault condition is removed PROTECTION OVER VOLTAGE OVER TEMPERATURE CH1:5.75 ~ 6.75V CH2:13.8 ~ 16.2V CH1: 5.75 ~ 6.75V Protection type : Shut down o/p voltage, re-power on to recover 95 5 6.0% CH2:17.25 ~ 20.25V CH1:5.75 ~ 6.75V CH2:3.8 ~ 4.4V (TSW1) Detect on heatsink of Q1,Q2 power transistor Protection type : Shut down o/p voltage, recovers automatically after temperature goes down FUNCTION POWER GOOD / POWER FAIL(OPTIONAL) 10ms/1ms -10 ~ +60 (Refer to output load derating curve) WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS WITHSTAND VOLTAGE 20 ~ 90% RH non-condensing -20 ~ +85 , 10 ~ 95% RH 0.03%/ (0~50 ) 10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes UL60950-1, TUV EN60950-1 Approved I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC SAFETY & ISOLATION RESISTANCE EMI CONDUCTION & RADIATION Compliance to EN55022 (CISPR22) Class B EMC (Note 5) HARMONIC CURRENT Compliance to EN61000-3-2,-3 EMS IMMUNITY Compliance to EN61000-4-2,3,4,5,6,8,11; ENV50204, EN55024, Light industry level, criteria A OTHERS MTBF 160.6K hrs min. DIMENSION 230*115*50mm (L*W*H) 1.2Kg; 12pcs/15.4Kg/0.92CUFT PACKING NOTE MIL-HDBK-217F (25 ) 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. 33.3% Duty cycle maximum within every 30 seconds. Average output power should not exceed the rated power. 5. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. 6. Derating may be needed under low input voltages. Please check the derating curve for more details. File Name:QP-200-SPEC 2005-09-13 RSG RSG Electronic Components GmbH Sprendlinger Landstr. 115 D-63069 Offenbach/Germany Tel. +49 69 984047-0 Fax +49 69 984047-77 [email protected] www.rsg-electronic.de ■ ■ ■ ■ ELECTRONIC COMPONENTS ■ ■ Änderungen vorbehalten / subject to change without notice QP-200 200W Quad Output with PFC Function series Features : Universal AC input / Full range Built-in active PFC function, PF>0.95 Protections:Short circuit/Over load/Over voltage/Over temperature Forced air cooling by built-in DC fan CH1,2 can be adjustable from -5~+10% With power good and fail signal output(Optional) Built-in remote sense function for CH1,2 100% full load burn-in test CH4 can set to positive after consult us before delivery Fixed switching frequency at PFC:67KHz PWM:134KHz(Optional) 3 years warranty .. SPECIFICATION QP-200-3B MODEL CH1 CH2 CH3 CH4 CH1 CH2 CH3 CH4 CH1 CH2 CH3 CH4 DC VOLTAGE 5V 3.3V 12V -12V 5V 3.3V 15V -15V 5V 3.3V 24V -12V RATED CURRENT 15A 15A 6A 0.7A 15A 15A 5A 0.7A 10A 15A 4A 0.7A CURRENT RANGE 3 ~ 20A 0 ~ 20A 0.5 ~ 8A 0 ~ 1A 3 ~ 20A 0 ~ 20A 0.5 ~ 6A 0 ~ 1A 3 ~ 15A 0 ~ 20A 0.4 ~ 5A 0 ~ 1A RATED POWER 204.9W 20A 6A 1A Note.4 20A 210W 20A 8A 1A 20A 203.9W 20A 7A 1A 20A RIPPLE & NOISE (max.) Note.2 100mVp-p 100mVp-p 150mVp-p 150mVp-p 100mVp-p 100mVp-p 150mVp-p 150mVp-p 100mVp-p 100mVp-p 150mVp-p 150mVp-p CH1: 4.75 ~ 5.5V VOLTAGE ADJ. RANGE CH2: 3.14 ~ 3.63V CH1: 4.75 ~ 5.5V CH2: 3.14 ~ 3.63V CH1: 4.75 ~ 5.5V CH2: 3.14 ~ 3.63V VOLTAGE TOLERANCE Note.3 3.0% 3.0% +8,-10% 6.0% 3.0% 3.0% +10,-6% 6.0% 3.0% 3.0% +10,-6% LINE REGULATION 1.0% 1.0% 2.0% 1.0% 1.0% 1.0% 2.0% 1.0% 1.0% 1.0% 2.0% 1.0% LOAD REGULATION 2.0% 2.0% 6.0% 2.0% 2.0% 2.0% 6.0% 2.0% 2.0% 2.0% 6.0% 2.0% SETUP, RISE TIME 800ms, 50ms at full load HOLD TIME (Typ.) 24ms at full load VOLTAGE RANGE INPUT QP-200-3D OUTPUT NUMBER PEAK CURRENT OUTPUT QP-200-3C Note.6 90 ~ 264VAC FREQUENCY RANGE 47 ~ 63Hz 127 ~ 370VDC POWER FACTOR (Typ.) PF>0.95/230VAC EFFICIENCY (Typ.) 72% AC CURRENT (Typ.) INRUSH CURRENT (Typ.) 3.5A/115VAC 2A/230VAC COLD START 30A PF>0.98/115VAC at full load 72% 74% LEAKAGE CURRENT <2mA / 240VAC OVER LOAD 105 ~ 150% rated output power Protection type : Constant current limiting, recovers automatically after fault condition is removed PROTECTION OVER VOLTAGE 6.0% CH1:5.75 ~ 6.75V CH2:3.8 ~ 4.4V Protection type : Shut down o/p voltage, re-power on to recover 95 5 (TSW1) Detect on heatsink of Q1,Q2 power transistor Protection type : Shut down o/p voltage, recovers automatically after temperature goes down FUNCTION POWER GOOD / POWER FAIL(OPTIONAL) 10ms/1ms -10 ~ +60 (Refer to output load derating curve) WORKING TEMP. OVER TEMPERATURE WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION 20 ~ 90% RH non-condensing -20 ~ +85 , 10 ~ 95% RH 0.03%/ (0~50 ) 10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes SAFETY STANDARDS UL60950-1, TUV EN60950-1 Approved WITHSTAND VOLTAGE I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC SAFETY & ISOLATION RESISTANCE EMI CONDUCTION & RADIATION Compliance to EN55022 (CISPR22) Class B EMC (Note 4) HARMONIC CURRENT Compliance to EN61000-3-2,-3 EMS IMMUNITY Compliance to EN61000-4-2,3,4,5,6,8,11; ENV50204, EN55024, Light industry level, criteria A OTHERS MTBF 160.6K hrs min. DIMENSION 230*115*50mm (L*W*H) 1.2Kg; 12pcs/15.4Kg/0.92CUFT PACKING NOTE MIL-HDBK-217F (25 ) 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. 33.3% Duty cycle maximum within every 30 seconds. Average output power should not exceed the rated power. 5. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. 6. Derating may be needed under low input voltages. Please check the derating curve for more details. File Name:QP-200-SPEC 2005-09-13 RSG RSG Electronic Components GmbH Sprendlinger Landstr. 115 D-63069 Offenbach/Germany Tel. +49 69 984047-0 Fax +49 69 984047-77 [email protected] www.rsg-electronic.de ■ ■ ■ ELECTRONIC COMPONENTS ■ ■ ■ Änderungen vorbehalten / subject to change without notice QP-200 200W Quad Output with PFC Function series Features : Universal AC input / Full range Built-in active PFC function, PF>0.95 Protections:Short circuit/Over load/Over voltage/Over temperature Forced air cooling by built-in DC fan CH1,2 can be adjustable from -5~+10% With power good and fail signal output(Optional) Built-in remote sense function for CH1,2 100% full load burn-in test CH4 can set to positive after consult us before delivery Fixed switching frequency at PFC:67KHz PWM:134KHz(Optional) 3 years warranty .. SPECIFICATION QP-200-3E MODEL OUTPUT NUMBER CH1 CH2 CH3 CH4 DC VOLTAGE 5V 3.3V 24V -15V RATED CURRENT 10A 15A 4A 0.7A CURRENT RANGE 3 ~ 15A 0 ~ 20A 0.4 ~ 5A 0 ~ 1A 20A 6A 1A 100mVp-p 150mVp-p 150mVp-p 206W RATED POWER PEAK CURRENT OUTPUT Note.4 20A RIPPLE & NOISE (max.) Note.2 100mVp-p CH1: 4.75 ~ 5.5V VOLTAGE ADJ. RANGE 3.0% 3.0% +10,-6% 6.0% LINE REGULATION 1.0% 1.0% 2.0% 1.0% LOAD REGULATION 2.0% 2.0% 6.0% 2.0% 800ms, 50ms at full load SETUP, RISE TIME 24ms at full load HOLD TIME (Typ.) VOLTAGE RANGE Note.6 90 ~ 264VAC FREQUENCY RANGE POWER FACTOR (Typ.) INPUT CH2: 3.14 ~ 3.63V VOLTAGE TOLERANCE Note.3 EFFICIENCY (Typ.) AC CURRENT (Typ.) INRUSH CURRENT (Typ.) 127 ~ 370VDC 47 ~ 63Hz PF>0.95/230VAC PF>0.98/115VAC at full load 74% 3.5A/115VAC 2A/230VAC COLD START 30A LEAKAGE CURRENT <2mA / 240VAC OVER LOAD 105 ~ 150% rated output power Protection type : Constant current limiting, recovers automatically after fault condition is removed PROTECTION OVER VOLTAGE CH1:5.75 ~ 6.75V CH2:3.8 ~ 4.4V Protection type : Shut down o/p voltage, re-power on to recover 95 5 (TSW1) Detect on heatsink of Q1,Q2 power transistor Protection type : Shut down o/p voltage, recovers automatically after temperature goes down FUNCTION POWER GOOD / POWER FAIL(OPTIONAL) 10ms/1ms -10 ~ +60 (Refer to output load derating curve) WORKING TEMP. OVER TEMPERATURE WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS WITHSTAND VOLTAGE 20 ~ 90% RH non-condensing -20 ~ +85 , 10 ~ 95% RH 0.03%/ (0~50 ) 10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes UL60950-1, TUV EN60950-1 Approved I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC SAFETY & ISOLATION RESISTANCE EMI CONDUCTION & RADIATION Compliance to EN55022 (CISPR22) Class B EMC (Note 5) HARMONIC CURRENT Compliance to EN61000-3-2,-3 EMS IMMUNITY Compliance to EN61000-4-2,3,4,5,6,8,11; ENV50204, EN55024, Light industry level, criteria A OTHERS MTBF 160.6K hrs min. DIMENSION 230*115*50mm (L*W*H) 1.2Kg; 12pcs/15.4Kg/0.92CUFT PACKING NOTE MIL-HDBK-217F (25 ) 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. 33.3% Duty cycle maximum within every 30 seconds. Average output power should not exceed the rated power. 5. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. 6. Derating may be needed under low input voltages. Please check the derating curve for more details. File Name:QP-200-SPEC 2005-09-13 RSG RSG Electronic Components GmbH Sprendlinger Landstr. 115 D-63069 Offenbach/Germany Tel. +49 69 984047-0 Fax +49 69 984047-77 [email protected] www.rsg-electronic.de ■ ■ ■ ■ ELECTRONIC COMPONENTS ■ ■ Änderungen vorbehalten / subject to change without notice QP-200 200W Quad Output with PFC Function Mechanical Specification Case No. 912B series Unit:mm 117.5 32.5 150 27.5 177.5 LED V2 V1 ADJ. 6 1 36.5 CN2 9 8 115 50 95 6 9.5 135 7 4-M4 L=5mm 5 47.5 50.5 4 3 8 32.5 5-M3 L=3mm 2 16 10 1 15 Air flow direction 215 51.5 CL 25 50 150 32.5 4-M4 L=6mm Terminal pin number assignment : Pin No. 1 2 3 Assignment AC/L AC/N FG DC Output Connector (CN2) : JST S6B-XH-A-1 or equivalent Pin No. Assignment Pin No. Assignment 4 DC OUTPUT V4 7,8 DC OUTPUT COM 5 DC OUTPUT V3 9 DC OUTPUT V2 6 DC OUTPUT V1 Derating Curve Pin No. Assignment Pin No. Assignment 1 V1(+S) 4 V2(-S) 2 V1(-S) 5 PF/PG 3 V2(+S) 6 G Mating Housing JST XHP or equivalent Terminal JST SXH-001T-P0.6 or equivalent Output Derating VS Input Voltage 100 100 90 80 80 QP-200-3A 70 70 LOAD(%) LOAD (%) 60 40 20 -10 -10 0 0 10 20 30 40 AMBIENT TEMPERATURE ( 50 ) 60 (HORIZONTAL) 60 50 40 90 100 115 135 155 230 264 INPUT VOLTAGE (VAC) 60Hz File Name:QP-200-SPEC 2005-09-13