ARTESYN AFE1200

AFE1200 SERIES
Single output
• Approved to EN61000, IEC-1000, UL1950,
CSA 22.2 No. 950-95
• Operating ambient temperature of 0°C to +50°C
• Complies with ETS300 132-1 and EN61000-3-2
• Hot-swap capability
• 11.5 x 6.75 x 3.35 inch size
• N+1 redundancy capability
• Extensive features available
• Compatible with AFS standard shelves for configuring
rack-mounted power systems
The AFE1200 power module is a rack mountable single phase AC to DC power
supply, designed to be a cost-competitive front-end power supply for distributed
power systems. It is particularly suitable for use in data processing, datacom and
telecom applications. The outputs are fully floating, enabling users to adopt whatever
rail reference configuration they require. The AFE1200 power modules are designed
for hot-swap operation and can be mounted into AFS2400/4800 power shelves for
redundant-mode operation.
[ 2 YEAR WARRANTY ]
SPECIFICATION
All specifications are typical at nominal input, full load at 25°C unless otherwise stated
EMC CHARACTERISTICS
OUTPUT SPECIFICATIONS
Output voltage
Main: 24/48Vdc
Auxiliary: 12Vdc
±1.5%
±1.0%
Output power
Main
Auxiliary
1200W
12W
Regulation
Line, load, IT, ageing
±3.0%
Turn-on
Output rise time
100 to 400ms
Turn-on (AC applied)
4s max.
Turn-on (inhibit removed)
1.5s max.
Conducted emissions
Radiated emissions
Ripple and noise
<50MHz
Transmission noise
100 to 3kHz
Immunity - radiated
Immunity - ESD
Line harmonics
FCC-CFR, part 15, subpart A Class A
CISPR 22
Class A
FCC-CFR, part 15, subpart A (Note 8)
CISPR 22
(Note 8)
IEC1000-3
Level 3
IEC1000-2
Level 3
per EN61000-3-2
Compliant
GENERAL SPECIFICATIONS
Hold-up time
(See Note 2)
75 to 85VAC
0 to 75VAC
Efficiency
120VAC
220VAC
Isolation voltage
Input/output
Input/chassis
Output/chassis
480mV pk-pk
35dBrnC
Overvoltage protection
60VDC max.
Undervoltage protection >44.5VDC
<42VDC for >5s
Delivers full power
Latch-off
83%
86%
Switching frequency
Short circuit protection
Current sharing
<30s
>30s
Automatic recovery
Latch-off
Active current share
(50% to 100% loading)
Remote sense
500ms
20ms
3000VAC
1500VAC
100VAC
200kHz
Approvals and
standards
EN60950, IEC950, UL1950
CSA C22.2 No. 950
±10%
Case material
Electrolytic zinc coated CRS,
ASTM A591, light beige paint
1.0V max. distribution line loss
Weight
4.0kg (8Ibs)
INPUT SPECIFICATIONS
MTBF
Input voltage range
115/230VAC nom.
85 to 264VAC
Input frequency range
50/60Hz nom.
47Hz to 63Hz
Input inrush current
25°C cold start
12A typical
Safety ground
leakage current
254VAC @ 60Hz
1.5mA max.
1.1mA typ.
Input current
220VAC, 1200W
Power factor
150,000 hours
300,000 hours
ENVIRONMENTAL SPECIFICATIONS
Thermal performance
Operating ambient
Non-operating
Cooling
0°C to +50°C
-40°C to +100°C
Forced air
7.0A rms
Relative humidity
Operating
5% to 95% RH
0.99 min.
Altitude
Operating
13,000 feet max.
Vibration
5Hz to 500Hz
Shock
PAGE 1
MIL-HDBK-217E
Demonstrated
0.75G rms peak
15G, 1/2 Sine, 11ms
DISTRIBUTED POWER FRONT END AC/DC POWER SUPPLIES
|
1200W AC/DC
1200 Watt
AC/DC PFC front-end for distributed power architectures
OUTPUT
OUTPUT CURRENT
TOTAL
REMOTE
PARALLEL
REGULATION
ON/OFF
INTERFACES
RIPPLE
MODEL NUMBER
VOLTAGE
MIN
MAX
48VDC
0A
25A
480mV
±3.0%
Inhibit
All
AFE1200-96S48NA
24VDC
0A
50A
240mV
±3.0%
Inhibit
All
AFE1200-96S24NA
Parallel interface specifications
All signals are referenced to ISO_GND unless otherwise indicated.
Isolated signal ground
(ISO_GND)
May be connected to any voltage in the range from +Vout+5VDC to -Vout5VDC.
Overtemperature
(OTW)
Output bi-level signal. Bi-level signals with a 5mA sink capability and
maximum voltage stand-off of 60VDC.
Logic 0 : Signal precedes OT shutdown by 5ms.
Logic 1 : Normal operation.
Remote On/Off
(INHIBIT)
Input bi-level signals. Bi-level input signals shall be no greater than 5VDC.
Logic 0 : Output inhibit.
Logic 1 : Normal operation.
Voltage margin down
(DOWN)
Input bi-level signals. Bi-level input signals shall be no greater than 5VDC.
Logic 0 : Nominal output voltage.
Logic 1 : 44.5 to 45.5VDC output.
Power good signal
(PWR_GOOD)
Output bi-level signal. Bi-level signals are open-collector (drain) with a 5mA
sink capability and maximum voltage stand-off of 60VDC.
Logic 0 : Output undervoltage.
Logic 1 : Output voltage normal.
AC Good
(AC OK)
Output bi-level signal. Bi-level output signal is open-collector (drain) with a
5mA sink capability and maximum voltage stand-off of 60VDC.
Logic 0 : AC input below normal operating range.
Logic 1 : AC input within steady-state operating range.
Voltage monitoring
(VMARG)
Input analog signal referenced to RS-. Adjusts output up to 4VDC higher than
the nominal set point.
Features
Live insertion and removal
OR-ing diodes provided on output.
Voltage monitoring jacks
Located on front panel.
LED’s (located on front panel)
Power Good
Power Fail
AC Good
-
Green
Red
Green
Protection
Thermal protection - automatic shut-off for fan failure or internal
overtemperature.
Fault fail signal
(F/F ±)
Differential relay contact, isolated from all outputs and returns within the
power module.
Relay closed : Power supply failure
Relay open : Normal operation.
Output Overload and Short Circuit - automatic shut-down after 30 seconds.
Current regulated output down to less than 1VDC.
Power fail warning signal
(PFW)
Output bi-level signal. Bi-level signals are open-collector (drain) with a 5mA
sink capability and maximum voltage stand-off of 60VDC.
Logic 0 : Signal precedes loss of output power by 5ms.
Logic 1 : Normal operation.
Output Undervoltage - automatic shut-down below 42VDC.
Module Missing Pin
(MM)
Provision for detection of unseated or removed module. MM pins are
common internal to the power supply. Internal pull-up resistor to +5VDC logic
bias, referenced to isolated GND
Short Pin
Short pin located in the output connector initiates shut down of the power
supply output when the power supply is removed from the host power shelf.
Output Overvoltage - automatic shut-down for both main (60VDC max.) and
auxiliary (15.6VDC max.) outputs.
Current Share
Active current sharing for up to 9 AFE1200 power modules.
Auxiliary Output
(AUX ±)
12VDC auxiliary output. Isolated from the main output. May be utilized for
external housekeeping supply and connected to either main output.
Current Monitor
(IMON)
Current source which mirrors magnitude of the output current. Signal return
is referenced to RS-.
Current Limit
(CL)
Output bi-level signal. Bi-level output signal with a 5mA sink capability and
maximum voltage stand-off of 60VDC.
Logic 0 : Output is in current mode control and is current limiting.
Logic 1 : Normal operation.
Reset
(RESET)
Input bi-level signal. Bi-level input signal shall be no greater than 5VDC.
Logic 0 : Normal operation.
Logic 1 : Resets fault indicators without unit shut-down.
International Safety Standard Approvals
AFE1200-96S24NA safety approval is pending
EN60950/IEC950 File No. E9972397
UL1950 File No. E135734
Please consult our website for the following items: ✔ Application Note
http://www.artesyn.com
PAGE 2
1200W AC/DC
|
DISTRIBUTED POWER FRONT END AC/DC POWER SUPPLIES
1200 Watt
AC/DC PFC front-end for distributed power architectures
PIN CONNECTIONS
PIN NO.
1
FUNCTION
PIN NO.
Not Used
10
2
Not Used
11
3
PWR RTN
12
4
PWR RTN
5
FUNCTION
SGND
RS-
PIN NO.
(4)
19
(4)
FUNCTION
PFW
PIN NO.
FUNCTION
27
VMARG
28
EXT VCC+
(1)
(3)
20
ISO GND
RS+
21
IMON
29
AUX-
13
F/F-
22
Power Good
30
I SHR
PWR RTN
14
CL
23
F/F+
31
OTW
6
+Vout
15
N/U
24
MM
32
AUX+
7
+Vout
16
MM
25
DOWN
33
SHORT PIN
8
+Vout
17
AC OK
26
INHIBIT
34
9
Not Used
18
RESET
CGND
(2)
Notes
1
2
3
4
5
6
PFW signal warning issued 5 msec prior to shutdown.
Chassis or safety ground.
Isolated signal ground.
Secondary return and RS- are common and tied together internally.
Refer to Application Note 110 for installation of the AFE1200 power
modules into the AFS2400/AFS4800 power shelf.
Refer to Application Note 110 for description of outputs and signals
available with AFE1200 power modules installed in Artesyn standard frontend power shelf.
7
8
Class A for power module, Class B when installed in AFS2400/4800 power
shelf (subject to cable/system configuration).
NOTICE: Some models do not support all options. Please contact your
local Artesyn representative or use the on-line model number search tool at
http://www.artesyn.com/powergroup/products.htm to find a suitable
alternative.
NORMAL
6.44
(163.58)
AIR FLOW
.074 (1.880)
11.46
(291.08)
1.30
(33.02)
AC INPUT
POWER DYNAMICS 42R08-1122
MATE - POWER DYNAMICS 43R06-2114
6.75
(171.45)
GUIDE
PIN HOLE
GUIDE
PIN HOLE
.050
(1.270)
.800
(20.320)
.662
(16.815)
3.35
(85.09)
2.75
(69.85)
1.150
(29.210)
REF
.483 (12.268)
.350
(8.890)
2.098
(53.289)
5.750 (146.05)
6.44 (163.58)
INSERTION / EJECTOR
HANDLE WITH 6-32
CAPTIVE SCREW
ALL MEASUREMENTS INCHES (MM)
(J2) DC mating connector
Elcon 377-0002-00100A or equivalent.
Elcon 376-0002-00200A or equivalent.
(J1) AC connector
(J1) AC mating connector
Power Dynamics 42R08-1122 or equivalent.
Power Dynamics 43R06-2114 or equivalent.
Datasheet © Artesyn Technologies® 2005
The information and specifications contained in this datasheet are believed to be correct at time of publication. However, Artesyn Technologies accepts no responsibility for consequences arising
from printing errors or inaccuracies. Specifications are subject to change without notice. No rights under any patent accompany the sale of any such product(s) or information contained herein.
PAGE 3
ds_afe1200_20050824.PDF
(J2) DC connector
MAIN DC OUTPUT/SIGNALS
ELCON 377-0002-00110A (PINS)
MATE-ELCON 376-0002-00200A (SOCKETS)