VISHAY SFH6700/ 01/ 02/ 05/ 11/ 12/ 19 Vishay Semiconductors High Speed Optocoupler, 5 MBd, 1 kV/µs dV/dt Features • Data Rate 5.0 MBits/s (2.5 MBit/s over Temperature) • Buffer • Isolation Test Voltage, 5300 V RMS for 1.0 s • TTL, LSTTL and CMOS Compatible • Internal Shield for Very High Common Mode Transient Immunity • Wide Supply Voltage Range (4.5 to 15 V) • Low Input Current (1.6 mA to 5.0 mA) • Three State Output (SFH6700/ 19) • Totem Pole Output (SFH6701/ 02/ 11/ 12) • Open Collector Output (SFH6705) • Specified from 0 °C to 85 °C SFH6700/6719 SFH6701/6711 NC 1 8 VCC NC 1 A 2 7 VO A 2 7 VO C 3 6 VE C 3 6 NC NC 4 5 GND 8 VCC 5 GND NC 4 SFH6702/6712 SFH6705 NC 1 8 VCC A 2 7 NC A 2 7 NC C 3 6 VO C 3 6 VO NC 4 8 VCC NC 1 5 GND 5 GND NC 4 i179073 Agency Approvals • UL - File No. E52744 System Code H or J • DIN EN 60747-5-2(VDE0884) DIN EN 60747-5-5 pending Available with Option 1 The SFH67xx uses an industry standard DIP-8 package.With standard lead bending, creepage distance and clearance of ≥ 7.0 mm with lead bending options 6, 7, and 9 ≥ 8 mm are achieved. Applications Industrial Control Replace Pulse Transformers Routine Logic Interfacing Motion/Power Control High Speed Line Receiver Microprocessor System Interfaces Computer Peripheral Interfaces Description The SFH67xx high speed optocoupler series consists of a GaAlAs infrared emitting diode, optically coupled with an integrated photo detector. The detector incorporates a Schmitt-Trigger stage for improved noise immunity. Using the Enable input, the output can switched to the high ohmic state, which is necessary for data bus applications. A Faraday shield provides a common mode transient immunity of 1000 V/µ at VCM = 50 V for SFH6700/ 01/ 02/ 05 and 2500 V/µ at VCM = 400 V for SFH6711/ 12/ 19. Document Number 83683 Rev. 1.3, 27-Apr-04 Order Information Part Remarks SFH6700 Three State Output, DIP-8 SFH6701 Totem Pole Output, DIP-8 SFH6702 Totem Pole Output, DIP-8 SFH6705 Open Collector Output, DIP-8 SFH6711 Totem Pole Output, DIP-8 SFH6712 Totem Pole Output, DIP-8 SFH6719 Three State Output, DIP-8 SFH6700-X009 Three State Output, SMD-8 (option 9) SFH6701-X006 Totem Pole Output, DIP-8 400 mil (option 6) SFH6701-X007 Totem Pole Output, SMD-8 (option 7) SFH6701-X009 Totem Pole Output, SMD-8 (option 9) SFH6705-X006 Open Collector Output, DIP-8 400 mil (option 6) SFH6705-X007 Open Collector Output, SMD-8 (option 7) SFH6711-X007 Totem Pole Output, SMD-8 (option 7) For additional information on the available options refer to Option Information. www.vishay.com 1 SFH6700/ 01/ 02/ 05/ 11/ 12/ 19 VISHAY Vishay Semiconductors Truth Table (Positive Logic) IR Diode Enable Output on H Z off H Z SFH6719 on L H off L SFH6701 on off L SFH6702 on H off L SFH6705 on H off L SFH6711 on H off L SFH6712 on H off L SFH6700 L H Absolute Maximum Ratings Tamb = 25 °C, unless otherwise specified Stresses in excess of the absolute Maximum Ratings can cause permanent damage to the device. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute Maximum Rating for extended periods of the time can adversely affect reliability. Input Symbol Value Reverse voltage Parameter VR 3.0 V DC Forward current IF 10 mA IFSM 1.0 A Pdiss 20 mW Surge forward current Test condition t ≤ 1.0 µs Power dissipation Unit Output Symbol Value Unit Supply voltage Parameter Test condition VCC - 0.5 to + 15 V Three state enable voltage (SFH6700/19 only) VEN - 0.5 to + 15 V Output voltage VO - 0.5 to + 15 V Average output current IO 25 mA Pdiss 100 mW Unit Power dissipation Coupler Symbol Value Storage temperature range Parameter Tstg - 55 to + 125 °C Ambient temperature range Tamb - 40 to + 85 °C Lead soldering temperature Test condition t = 10 s Isolation test voltage Pollution degree Creepage distance and clearance www.vishay.com 2 Tsld 260 °C VISO 5300 VRMS 2.0 Standard lead bending 7.0 mm Options 6, 7, 9 8.0 mm Document Number 83683 Rev. 1.3, 27-Apr-04 SFH6700/ 01/ 02/ 05/ 11/ 12/ 19 VISHAY Vishay Semiconductors Parameter Test condition Symbol Value Comparative tracking index per DIN IEC 112/VDE 0303, part 1 Isolation resistance Unit 175 VIO = 500 V, Tamb = 25 °C RIO 1012 Ω VIO = 500 V, Tamb = 100 °C RIO 11 Ω 10 ICC ICC VCC (8) IF A VCC (8) IF A (2) (2) IO IE K (3) VEN (6) GND (5) Shield IO VO (7) VO (6) K (3) GND (5) Shield SFH6700/19 SFH6702/12 ICC ICC VCC (8) IF A VCC (8) IF A (2) IO (2) IO VO (7) K VO (6) K (3) (3) GND (5) Shield GND (5) Shield SFH6701/11 SFH6705 isfh6700_01 Fig. 1 Schematics Recommended Operating Conditions A 0.1 µF bypass capacitor connected between pins 5 and 8 must be used. Parameter Test condition Part Symbol Min Max Unit VCC 4.5 15 V SFH6700 VEH 2.0 15 V SFH6719 VEH 2.0 15 V SFH6700 VEL 0 0.8 V SFH6719 VEL 0 0.8 V 5.0 mA 0.1 mA 85 °C Supply voltage Enable voltage high Enable voltage low Forward input current IFon 1.6 (1) IFoff TA 0 SFH6705 RL 350 SFH6705 N Operating temperature Output pull-up resistor Fan Output (1) RL = 1.0 kΩ Typ. 4 kΩ 16 LS TTL Loads We recommended using a 2.2 mA to permit at least 20 % CTR degradation guard band. Document Number 83683 Rev. 1.3, 27-Apr-04 www.vishay.com 3 SFH6700/ 01/ 02/ 05/ 11/ 12/ 19 VISHAY Vishay Semiconductors Electrical Characteristics Tamb = 25 °C, unless otherwise specified Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering evaluation. Typical values are for information only and are not part of the testing requirements. Input 0 °C ≤ Tamb ≤ 85 °C; 4.5 V ≤ VCC ≤ 15 V; 1.6 mA ≤ IFon ≤ 5.0 mA; 2.0 ≤ VEH ≤ 15 V; 0 ≤ VEL ≤ 0.8 V; 0 mA ≤ IFoff ≤ 0.1 mA; Typical values: Tamb = 25 °C; VCC = 5.0 V; IFon = 3.0 mA unless otherwise specified Parameter Forward voltage Input current hysteresis Test condition Symbol IF = 5.0 mA VF IF = 5.0 mA, VF VCC = 5.0 V, IHYS = IFon-IFon Min Typ. Max Unit 1.6 1.75 V 1.8 IHYS 0.1 V mA VR = 3.0 V IR 0.5 Capacitance VR = 0 V, f = 1.0 MHz; CO 60 pF Rthja 700 K/W Thermal resistance www.vishay.com 4 10 µA Reverse current Document Number 83683 Rev. 1.3, 27-Apr-04 SFH6700/ 01/ 02/ 05/ 11/ 12/ 19 VISHAY Vishay Semiconductors Output 0 °C ≤ Tamb ≤ 85 °C; 4.5 V ≤ VCC ≤ 15 V; 1.6 mA ≤ IFon ≤ 5.0 mA; 2.0 ≤ VEH ≤ 15 V; 0 ≤ VEL ≤ 0.8 V; 0 mA ≤ IFoff ≤ 0.1 mA; Typical values: Tamb = 25 °C; VCC = 5.0 V; IFon = 3.0 mA unless otherwise specified Parameter Test condition Symbol Min Typ. 0.5 Unit IOL = 6.4 mA Logic high output voltage (except SFH6705) IOH = 2.6 mA, VOH = VCC-1.8 V Output leakage current (VOUT>VCC) (except SFH6705) VO = 5.5 V, VCC = 4.5 V, IF = 5.0 mA IOHH 0.5 100 µA VO = 15 V, VCC = 4.5 V, IF = 5.0 mA IOHH 1.0 500 µA VO = 5.5 V, VCC = 5.5 V, IF = 5.0 mA IOHH 0.5 100 µA VO = 15 V, VCC = 15 V, IF = 5.0 mA IOHH 1.0 500 µA Output leakage current (SFH705 only) VOL Max Logic low output voltage 2.4 V V Logic high enable voltage (SFH6700/19 only) VEH Logic low enable voltage (SFH6700/19 only) VEL 0.8 V VEN = 2.7 V IEH 20 µA 100 µA 250 µA Logic high enable current (SFH6700/19 only) 2.0 V VEN = 5.5 V IEH VEN = 15 V IEH Logic low enable current (SFH6700/19 only) VEN = 0.4 V IEL - 320 High impedance state output current (SFH6700/19 only) VO = 0.4 V, VEN = 2.0 V, IF = 5.0 mA IOZL - 20 VO = 2.4 V, VEN = 2.0 V, IF = 0 mA IOZH 20 µA VO = 5.5 V, VEN = 2.0 V, IF = 0 mA IOZH 100 µA µA - 50 µA IOZH 0.001 500 µA ICCL 3.7 6.0 mA VCC = 15 V, IF = 0 ICCL 4.1 6.5 mA VCC = 5.5 V, IF = 5.0 mA ICCH 3.4 4.0 mA VCC = 15V, IF = 5.0 mA ICCH 3.7 5.0 mA VO = VCC = 5.5 V, IF = 0 IOSL 25 40 Logic low supply current VCC = 5.5 V, IF = 0 Logic high supply current Logic low short circuit output 0.001 mA current 2) Logic high short circuit output current 2) VO = VCC = 15 V, IF = 0 IOSL VCC = 5.5 V, VO = 0 V, IF = 5.0 mA IOSL - 10 mA VCC = 15 V, VO = 0 V, IF = 5.0 mA IOSL - 25 mA Thermal resistance 2) Rthja mA 300 K/W Output short circuit time ≤ 10ms. Document Number 83683 Rev. 1.3, 27-Apr-04 www.vishay.com 5 SFH6700/ 01/ 02/ 05/ 11/ 12/ 19 VISHAY Vishay Semiconductors Coupler 0 °C ≤ Tamb ≤ 85 °C; 4.5 V ≤ VCC ≤ 15 V; 1.6 mA ≤ IFon ≤ 5.0 mA; 2.0 ≤ VEH ≤ 15 V; 0 ≤ VEL ≤ 0.8 V; 0 mA ≤ IFoff ≤ 0.1 mA; Typical values: Tamb = 25 °C; VCC = 5.0 V; IFon = 3.0 mA unless otherwise specified Parameter Test condition Symbol Min Typ. Max 0.6 Unit pF Capacitance (input-output) f = 1.0 MHz, pins 1-4 and 5-8 shorted together CIO Isolation resistance VIO = 500 V, Tamb = 25 °C RIO 1012 Ω VIO = 500 V, Tamb = 100 °C RIO 11 Ω 10 Switching Characteristics 0 °C ≤ Tamb ≤ 85 °C; 4.5 V ≤ VCC ≤ 15 V; 1.6 mA ≤ IFon ≤ 5.0 mA; 2.0 ≤ VEH ≤ 15 V (SFH6700/19); 0 ≤ VEL ≤ 0.8 V (SFH6700/19); 0 mA ≤ IFoff≤ 0.1 mA Typical values: Tamb = 25 °C; VCC = 5.0 V; IFon = 3.0 mA unless otherwise specified. (3) Parameter Propagation delay time to logic low output level, SFH6700/01/ 02/11/12/19 Test condition Without peaking capacitor With peaking capacitor Symbol Min Typ. tPHL 120 Max Unit ns tPHL 115 tPLH 125 tPLH 90 Output enable time to logic high (SFH6700/19) tPZH 20 ns Output enable time to logic low (SFH6700/19) tPZL 25 ns Output disable time from logic low (SFH6700/19) tPLZ 50 ns 300 ns 300 ns ns Output rise time 10 % to 90 % tr 40 ns Output fall time 90 % to 10 % tf 10 ns (3) A 0.1 µF bypass capacitor connected between pins 5 and 8 must be used Typical values: Tamb = 25 °C, VCC = 5.0 V; IFon = 3.0 mA; RL = 390 Ω unless otherwise specified (3) Parameter Propagation delay time to logic low output level Output rise time www.vishay.com 6 Part Symbol Without peaking capacitor Test condition SFH6705 tPHL Min Typ. 115 With peaking capacitor SFH6705 tPHL 105 Max Unit ns 300 ns 300 ns Without peaking capacitor SFH6705 tPLH 125 With peaking capacitor SFH6705 tPLH 90 ns 10 % to 90 % tr 25 ns 90 % to 10 % tr 4 ns Document Number 83683 Rev. 1.3, 27-Apr-04 SFH6700/ 01/ 02/ 05/ 11/ 12/ 19 VISHAY Vishay Semiconductors Common Mode Transient Immunity Tamb = 25 °C, VCC = 5.0 V (4) Parameter Test condition |VCM| = 50 V, IF = 1.6 mA Logic High Common Mode Transient Immunity Min Typ. Max Unit |CMH| 1000 V/µs SFH6701 |CMH| (4) 1000 V/µs SFH6702 |CMH| (4) 1000 V/µs SFH6705 |CMH| (4) 1000 V/µs SFH6711 |CMH| (4) 2500 V/µs SFH6712 |CMH| (4) 2500 V/µs SFH6719 |CMH| (4) 2500 V/µs |VCM| = 50V, IF = 0 mA SFH6700 |CML| (4) 1000 V/µs |VCM| = 50 V, IF = 0 mA SFH6701 |CML| (4) 1000 V/µs SFH6702 |CML| (4) 1000 V/µs SFH6705 |CML| (4) 1000 V/µs SFH6711 |CML| (4) 2500 V/µs SFH6712 |CML| (4) 2500 V/µs SFH6719 |CML| (4) 2500 V/µs |VCM| = 400 V, IF = 0 mA (4) Symbol (4) |VCM| = 400 V, IF = 1.6 mA Logic Low Common Mode Transient Immunity Part SFH6700 CMH is the maximum slew rate of a common mode voltage VCM at which the output voltage remains at logic high level (VO > 2.0 V) CML is the maximum slew rate of a common mode voltage VCM at which the output voltage remains at logic high level (VO < 0.8 V) Typical Characteristics (Tamb = 25 °C unless otherwise specified) 10.000 IF - Forward Current - mA Ptot - Power dissipation - mW 150 120 Detector 100 75 50 Emitter 25 0 –60 –40 –20 0 20 40 60 80 100 1.000 0.100 0.010 1.3 Fig. 2 Permissible Total Power Dissipation vs. Temperature Document Number 83683 Rev. 1.3, 27-Apr-04 1.5 1.6 1.7 VF - Forward Voltage TA - Temperature - °C isfh6700_02 1.4 isfh6700_03 Fig. 3 Typical Input Diode Forward Current vs. Forward Voltage www.vishay.com 7 SFH6700/ 01/ 02/ 05/ 11/ 12/ 19 VISHAY Vishay Semiconductors ICC - Supply Curent - mA VF - Forward Voltage - V 1.75 IF = 5 mA 1.70 1.65 1.60 1.55 1.50 1.45 -60 -40 -20 0 20 40 60 80 4.2 ICCL @ VCC = 15 V 4.0 ICCH @ VCC = 15 V & ICCL @ VCC = 5.5 V 3.8 3.6 ICCH @ VCC = 5.5 V 3.4 3.2 -60 -40 -20 0 20 40 60 80 100 TA - Temperature - °C 100 TA - Temperature - °C isfh6700_04 isfh6700_07 Fig. 4 Typical Forward Input Voltage vs. Temperature Fig. 7 Typical Supply Current vs. Temperature IOHH - Output Leakage Current - nA VO - Output Voltage - V 5 VCC = 4.5 V 4 3 IOH = –2.6 mA 2 1 1100 1000 900 600 500 VCC = VO = 5.5 V 400 -60 -40 -20 IOL = 6.4 mA 0 0.0 0.1 VCC = VO = 15 V 800 700 0.2 0.3 0.4 0.5 0.6 0 20 40 60 80 100 TA - Temperature - °C 0.7 0.8 0.9 1.0 IF -Input Current - mA isfh6700_05 isfh6700_08 Fig. 5 Typical Output Voltage vs. Forward Input Current (except SFH6705) Fig. 8 Typical Output Leakage Current vs. Temperature 6 IOL - Low Level Output Current - mA VO - Output Voltage - V 5 40 VCC = 5 V 4 3 2 RL = 1k - 4kΩ 1 RL = 390 Ω 35 33 VOL = 0.8 V 30 28 VOL = 0.6 V 25 23 VOL = 0.4 V 20 0 0.0 -60 0.2 0.4 0.6 0.8 IF - Forward Input Current - mA 1.0 isfh6700_06 Fig. 6 Typical Output Forward Voltage vs. Forward Input Current (only SFH6705) www.vishay.com 8 VCC = 5 V IF = 0 mA 38 -40 -20 0 20 40 60 80 100 TA - Temperature - °C isfh6700_09 Fig. 9 Typical Low Level Output Current vs. Temperature Document Number 83683 Rev. 1.3, 27-Apr-04 SFH6700/ 01/ 02/ 05/ 11/ 12/ 19 VISHAY VOL - Low Level Output Voltage - V 0.30 0.25 VCC = 5 V IF = 0 mA 0.20 IO = 16 mA 0.15 IO = 12.8 mA IO = 9.6 mA 0.10 0.05 -60 IO = 6.4 mA -40 -20 0 20 40 60 80 100 tPLH - Propagation Delay - ns Vishay Semiconductors TA - Temperature - °C 150 VCC = 5 V C = 15 pF (without peaking capacitor) IF = 1.6 mA 130 IF = 3 mA 110 IF = 5 mA 90 70 -60 -40 -20 0 20 40 60 80 100 TA - Temperature - °C isfh6700_10 isfh6700_24 Fig. 10 Typical Low Level Output Voltage vs. Temperature IOH - High Level Output Current - mA tPHL - Propagation Delay - ns 0 -1 -2 VCC = 4.5 V IF = 5 mA VOH = 2.7 V -3 -4 -5 VOH = 2.4 V -6 -7 -8 -60 -40 -20 0 20 40 60 80 Fig. 13 Typical Propagation Delay to Logic High vs. Temperature (except SFH6705) 100 TA - Temperature - °C 160 140 IF = 5 mA 120 IF = 3 mA 100 IF = 1.6 mA 80 60 -60 -40 -20 0 20 40 60 80 100 isfh6700_14 Fig. 11 Typical High Level Output Current vs. Temperature (except SFH6705 Fig. 14 Typical Propagation Delay to Logic LOw vs. Temperature (except SFH6705) tPLH - Propagation Delay - ns 60 54 VCC = 5 V 48 IF = 3 mA 42 36 30 tR 24 18 12 tF 6 0 -60 -40 -20 0 20 40 60 80 100 100 90 isfh6700_12 Fig. 12 Typical Rise, Fall Time vs. Temperature (except SFH6705) Document Number 83683 VCC = 5 V C1 = 120 pF (without peaking capacitor) 80 IF = 1.6, 3 and 5 mA 70 60 50 -60 -40 -20 0 20 40 60 80 100 TA - Temperature - °C TA - Temperature - °C Rev. 1.3, 27-Apr-04 VCC = 5 V C1 = 15 pF (without peaking capacitor) TA - Temperature - °C isfh6700_11 tR, tF -Rise, Fall Time - ns 180 isfh6700_15 Fig. 15 Typical Propagation Delays to Logic High vs. Temperature (except SFH6705) www.vishay.com 9 SFH6700/ 01/ 02/ 05/ 11/ 12/ 19 VISHAY tPLH - Propagation Delay - ns tPHL - Propagation Delay - ns Vishay Semiconductors 170 VCC = 5 V C1 = 120 pF (without peaking capacitor) 150 130 IF = 3 mA 110 IF = 5 mA 90 IF = 1.6 mA 70 50 -60 -40 -20 0 20 40 60 80 80 70 VCC = 5 V C1 = 120 pF (without peaking capacitor) 60 50 IF = 1.6, 3 and 5 mA 40 30 -60 100 -40 -20 isfh6700_16 VCC = 15 V C1 = 15 pF (without peaking capacitor) 80 100 180 IF = 1.6 mA tPHL -Propagation Delay - ns tPLH - Propagation Delay - ns 60 IF = 3 mA 90 80 IF = 5 mA 70 60 50 -60 -40 -20 0 20 40 60 80 Fig. 19 Typical Propagation Delays to Logic High vs. Temperature 100 VCC = 15 V 160 C1 = 120 pf (Peaking Capacitor is used) 140 120 IF = 5 mA IF = 3 mA 100 80 IF = 1.6 mA 60 -60 -40 -20 TA - Temperature - °C 0 20 40 60 80 100 TA - Temperature - °C isfh6700_17 isfh6700_20 Fig. 17 Typical Propagation Delays to Logic High vs. Temperature Fig. 20 Typical propagation delays to Logic Low vs. temperature (except SFH6705) 170 80 VCC = 5 V C1 = 15 pF (without peaking capacitor) 130 IF = 5 mA 110 IF = 3 mA 90 IF = 1.6 mA 70 50 -60 -40 -20 0 20 40 60 80 isfh6700_18 Fig. 18 Typical Propagation Delays to Logic Low vs.Temperature VCC = 15 V 60 50 40 tPLZ VCC = 4.5 V 30 20 10 0 -60 100 tPZL -40 VCC = 4.5 –15 V -20 0 20 40 60 80 100 TA - Temperature - °C TA - Temperature - °C www.vishay.com CL = 15 pF 70 tp - Enable Propagation Delay - ns tPHL - Propagation Delay - ns 40 isfh6700_19 Fig. 16 Typical Propagation Delay to Logic Low vs. Temperature 10 20 TA - Temperature - °C TA - Temperature - °C 150 0 isfh6700_21 Fig. 21 Typical Logic Low Enable Propagation Delays vs. Temperature (only SFH6700/11) Document Number 83683 Rev. 1.3, 27-Apr-04 SFH6700/ 01/ 02/ 05/ 11/ 12/ 19 VISHAY Vishay Semiconductors CL = 15 pF 70 tP - Enable Propagation Delay - ns tPHL - Propagation Delay - ns 80 60 VCC = 4.5 V tPHZ 50 40 30 tPZH VCC = 4.5 V –15 V 20 10 VCC = 15 V 0 -60 -40 -20 0 20 tPHZ 40 60 80 VCC = 5 V ˇ RL = 350 - 4 kΩ 140 130 IF = 5 mA 120 110 IF = 3 mA 100 IF = 1.6 mA 90 80 70 -60 100 -40 -20 TA - Temperature - °C Fig. 22 Typical Logic High Enable Propagation Delays vs. Temperature (only SFH6700/11) 40 60 80 100 Fig. 25 Typical Propagation Delays to Low Level vs. Temperature ( only SFH6705) 250 250 VCC = 5 V tR, tF -Rise, Fall Time - ns tP - Propagation Delay - ns 20 isfh6700_25 isfh6700_22 225 200 tPLH @ RL ˇ= 4 kΩ 150 tPLH @ RL = 1 ˇkΩ tPHL @ RL = 350 –4ˇ kΩ 100 tPLH @ RL =ˇ 35 kΩ 50 1 3 5 7 9 11 tR @ RL = 1 kΩ 50 tR @ RL = 350 kΩ 25 0 tF @ RL = 350-4 kΩ -25 -60 -40 -20 0 20 40 60 80 100 isfh6700_26 Fig. 23 Typical Propagation Delays vs. Pulse Input Current (only SFH6705) 200 tR @ RL = 4 kΩ TA - Temperature - °C isfh6700_23 220 VCC = 5V 200 IF - Pulse Input Current - mA tPLH - Propagation Delay - ns 0 TA - Temperature - °C Fig. 26 Typical Rise, Fall Time vs. Temperature (only SFH6705) VCC = 5 V IF = 3 mA 180 160 ˇ RL = 4 kΩ 140 RL = 1 ˇkΩ 120 RL = 350ˇkΩ 100 80 -60 -40 -20 0 20 40 60 80 100 TA - Temperature - °C isfh6700_24 Fig. 24 Typical Propagation Delays to High Level vs. Temperature (only SFH6705) Document Number 83683 Rev. 1.3, 27-Apr-04 www.vishay.com 11 SFH6700/ 01/ 02/ 05/ 11/ 12/ 19 VISHAY Vishay Semiconductors 5V VCC R3 = 619 Ohm Pulse generator tr, tf = 5 ns f = 100 kHz 10% Duty cycle VCC 8 Out* 7 1 IF 2 Input IF Monitoring Node Output Vo Monitoring Node 3 En* 4 Gnd D1 0.1 µF Bypass 6 D2 D3 5 D4 C2 = 15 pF R2 = 5 kOhm R1 C1 = 120 pF The Probe and Jig Capacitances are included in C1 and C2 All diodes are 1N916 or 1N3064 * SFH6701/02/11/12 without VEN * SFH6702/12 Pin 6 VOUT and Pin 7 n.c. R1 2.15 kOhm 1.1 kOhm 681 Ohm IF (ON) 1.6 mA 3 mA 5 mA IFon 50% IFon 0 mA Input IF VOH Output VO 1.3 V tPHL tPLH isfh6700_27 VOL Fig. 27 Test Circuit for tPLH, tPHL, tr and tf VCC Pulse generator tr, tf = 5 ns Zo = 50 Ohm 5V RL VCC 8 1 IF n.c. 7 2 Input IF Monitoring Node 3 VOUT 4 Gnd 6 0.1 µF Bypass 5 Output VO Monitoring Node C2 = 15 pF R1 C1 = 120 pF The Probe and Jig Capacitances are included in C1 and C2 R1 2.15 kOhm 1.1 kOhm 681 Ohm IF (ON) 1.6 mA 3 mA 5 mA IFon 50% IFon 0 mA Input IF VOH Output VO isfh6700_28 1.3 V tPLH VOL tPHL Fig. 28 Test Circuit for tPLH, tPHL, tr and - SFH6705 www.vishay.com 12 Document Number 83683 Rev. 1.3, 27-Apr-04 SFH6700/ 01/ 02/ 05/ 11/ 12/ 19 VISHAY Vishay Semiconductors VCC Pulse generator ZO = 50 Ohm tr, tf = 5 ns 2 Input VC Monitoring Node Output VO S1 Monitoring Node 619 Ohm D1 VCC 8 Out 7 1 IF 3 En 4 Gnd 5V 5 kOhm 6 D2 D3 D4 0.1µF C1 Bypass 5 S2 C1 = 15 pF including Probe and Jig Capacitances All diodes are 1N916 or 1N3064 3.0 V 1.3 V 0V Input VEN Output VO S1 closed S2 open 0.5 V S1 and S2 closed 1.3 V VOL t PZL tPLZ 0.5 V S1 open Output VO S2 closed 1.3 V VOH ca. 1.5 V S1 and S2 closed 0V isfh6700_29 t PZH t PHZ Fig. 29 Test Circuit for tPHZ, tPZH, tPLZ and tPZL-SFH6700/19 VCC Vcc 8 Out* 7 1 A 2 B R 3 En* 4 Gnd + Pulse Generator 6 Output VO Monitoring Node 0.1µF Bypass 5 – VCM * SFH6701/02/11/12 without VEN * SFH6702/12 Pin 6 VOUT and Pin 7 n.c. 400 V / 50 V VCM 0V VOH Switch at A: IF = 1.6 mA VO (min) Output VO isfh6700_30 VOL VO (max) Switch at B: IF = 0 mA Fig. 30 Test Circuit for Common Mode Transient Immunity and Typical Waveforms-SFH6700/01/02/11/12/19 Document Number 83683 Rev. 1.3, 27-Apr-04 www.vishay.com 13 SFH6700/ 01/ 02/ 05/ 11/ 12/ 19 VISHAY Vishay Semiconductors VCC 1 8 2 n.c. 7 5V RL A B R 3 Out 4 Gnd + Pulse Generator 0.1µF Bypass 6 Output VO Monitoring Node 5 – VCM 50 V VCM 0V Switch at A: IF = 1.6 mA VOH VO (min) Output VO VO (max) VOL Switch at B: IF = 0 mA isfh6700_31 Fig. 31 Test Circuit for Common Mode Transient Immunity and Typical Waveforms-SFH6705 Package Dimensions in Inches (mm) pin one ID 4 3 2 1 5 6 7 8 .255 (6.48) .268 (6.81) ISO Method A .379 (9.63) .390 (9.91) .030 (0.76) .045 (1.14) 4° typ. .031 (0.79) .300 (7.62) typ. .130 (3.30) .150 (3.81) .050 (1.27) .018 (.46) .022 (.56) i178006 www.vishay.com 14 .020 (.51 ) .035 (.89 ) .100 (2.54) typ. 10° 3°–9° .008 (.20) .012 (.30) .230(5.84) .110 (2.79) .250(6.35) .130 (3.30) Document Number 83683 Rev. 1.3, 27-Apr-04 SFH6700/ 01/ 02/ 05/ 11/ 12/ 19 VISHAY Vishay Semiconductors Option 6 Option 7 .407 (10.36) .391 (9.96) .307 (7.8) .291 (7.4) .300 (7.62) TYP. .180 (4.6) .160 (4.1) .0040 (.102) .315 (8.0) MIN. Document Number 83683 Rev. 1.3, 27-Apr-04 .375 (9.53) .395 (10.03) .300 (7.62) ref. .028 (0.7) MIN. .014 (0.35) .010 (0.25) .400 (10.16) .430 (10.92) Option 9 .331 (8.4) MIN. .406 (10.3) MAX. .0098 (.249) .012 (.30) typ. .020 (.51) .040 (1.02) .315 (8.00) min. 15° max. 18450 www.vishay.com 15 SFH6700/ 01/ 02/ 05/ 11/ 12/ 19 VISHAY Vishay Semiconductors Ozone Depleting Substances Policy Statement It is the policy of Vishay Semiconductor GmbH to 1. Meet all present and future national and international statutory requirements. 2. Regularly and continuously improve the performance of our products, processes, distribution and operatingsystems with respect to their impact on the health and safety of our employees and the public, as well as their impact on the environment. It is particular concern to control or eliminate releases of those substances into the atmosphere which are known as ozone depleting substances (ODSs). The Montreal Protocol (1987) and its London Amendments (1990) intend to severely restrict the use of ODSs and forbid their use within the next ten years. Various national and international initiatives are pressing for an earlier ban on these substances. Vishay Semiconductor GmbH has been able to use its policy of continuous improvements to eliminate the use of ODSs listed in the following documents. 1. Annex A, B and list of transitional substances of the Montreal Protocol and the London Amendments respectively 2. Class I and II ozone depleting substances in the Clean Air Act Amendments of 1990 by the Environmental Protection Agency (EPA) in the USA 3. Council Decision 88/540/EEC and 91/690/EEC Annex A, B and C (transitional substances) respectively. Vishay Semiconductor GmbH can certify that our semiconductors are not manufactured with ozone depleting substances and do not contain such substances. We reserve the right to make changes to improve technical design and may do so without further notice. Parameters can vary in different applications. All operating parameters must be validated for each customer application by the customer. Should the buyer use Vishay Semiconductors products for any unintended or unauthorized application, the buyer shall indemnify Vishay Semiconductors against all claims, costs, damages, and expenses, arising out of, directly or indirectly, any claim of personal damage, injury or death associated with such unintended or unauthorized use. Vishay Semiconductor GmbH, P.O.B. 3535, D-74025 Heilbronn, Germany Telephone: 49 (0)7131 67 2831, Fax number: 49 (0)7131 67 2423 www.vishay.com 16 Document Number 83683 Rev. 1.3, 27-Apr-04