PHOTOMULTIPLIER TUBE R7517 High QE, Bialkali Photocathode 28 mm (1-1/8 Inch) Diameter, 9-Stage, Side-On Type FEATURES ●Wide Spectral Response ......................... 185 nm to 760 nm ●High Cathode Sensitivity Luminous ................................................. 160 µA/lm Typ. Radiant at 420 nm ................................... 105 mA/W Typ. Quantum Efficiency at 220 nm ........................ 40 % Typ. ●High Anode Sensitivity (at 1000 V) Luminous ................................................. 1600 A/lm Typ. Radiant at 420 nm ............................ 10.5 × 105 A/W Typ. APPLICATIONS ●Fluorescence Spectrophotometers ●Fluorescence Immuno Assay ●SO2 Monitor (UV Fluorescence) SPECIFICATIONS GENERAL Figure 1: Typical Spectral Response Unit nm nm — mm — — — — pF pF — g °C °C — — 1000 CATHODE RADIANT SENSITIVITY (mA/W) QUANTUM EFFICIENCY (%) Parameter Description/Value 185 to 760 Spectral Response 420 Wavelength of Maximum Response MateriaI Bialkali Photocathode Minimum Effective Area 8 × 24 UV glass Window Material Secondary Emitting Surface Bialkali Structure Circular-cage Dynode Number of Stages 9 4 Direct Interelectrode Anode to Last Dynode 6 Anode to All Other Electrodes Capacitances Base 11-pin base JEDEC No. B11-88 Weight Approx. 45 Operating Ambient Temperature -30 to +50 Storage Temperature -30 to +50 SuitabIe Socket E678–11A (Sold Separately) E717–63 (Sold Separately) SuitabIe Socket Assembly E717–74 (Sold Separately) TPMSB0174EA CATHODE RADIANT SENSITIVITY 100 10 QUANTUM EFFICIENCY 1 0.1 0.01 100 200 300 400 500 600 700 WAVELENGTH (nm) Subject to local technical requirements and regulations, availability of products included in this promotional material may vary. Please consult with our sales office. Information furnished by HAMAMATSU is believed to be reliable. However, no responsibility is assumed for possible inaccuracies or omissions. Specifications are subject to change without notice. No patent rights are granted to any of the circuits described herein. ©2006 Hamamatsu Photonics K.K. 800 PHOTOMULTIPLIER TUBES R7517 MAXIMUM RATINGS (Absolute Maximum Values) Parameter Between Anode and Cathode Supply Voltage Between Anode and Last Dynode Average Anode Current A Value 1250 250 0.1 Unit V V mA CHARACTERISTlCS (at 25 °C) Parameter Quantum Efficiency (at Peak Wavelength) Luminous B at 210 nm Radiant at 420 nm Red/White Ratio C Blue Sensitivity Index D Luminous E at 210 nm Radiant at 420 nm Cathode Sensitivity Anode Sensitivity Min. Typ. 40 (at 220 nm) 160 71 105 0.01 13 1600 7.1 × 105 10.5 × 105 1.0 × 107 5 1.2 × 10-16 2.2 22 1.2 0.1 1.0 — 150 — — — 12 1200 — — — — — — — — — — Gain E Anode Dark Current F (After 30 min Storage in Darkness) ENI (Equivalent Noise Input) G Anode Pulse Rise Time H Time Response E Electron Transit Time I Transit Time Spread (TTS) J Light Hysteresis Anode Current Stability K Voltage Hysteresis Max. Unit — % — — — — — — — — — 50 — — — — — — µA/lm mA/W mA/W — — A/lm A/W A/W — nA W ns ns ns % % NOTES Table 1: Voltage Distribution Ratio Electrode K Distribution Ratio Dy1 Dy2 Dy3 Dy4 Dy5 Dy6 Dy7 Dy8 Dy9 1 1 1 1 1 1 1 1 1 P Dy: Dynode, F: Measured with the same supply voltage and voltage distribution ratio as Note E after removal of light. G:ENI is an indication of the photon-limited signal-to-noise ratio. It refers to the amount of light in watts to produce a signal-to-noise ratio of unity in the output of a photomultiplier tube. 2q.ldb.G.∆f S where q = Electronic charge (1.60 × 10-19 coulomb). ldb = Anode dark current (after 30 minute storage) in amperes. G = Gain. ∆f = Bandwidth of the system in hertz. 1 hertz is used. S = Anode radiant sensitivity in amperes per watt at the wavelength of peak response. l min. TIME 0 1 P: Anode l max. li Hysteresis = SuppIy Voltage: 1000 V, K: Cathode, ENI = H: The rise time is the time for the output pulse to rise from 10 % to 90 % of the peak amplitude when the entire photocathode is illuminated by a delta function light pulse. I: The electron transit time is the interval between the arrival of delta function light pulse at the entrance window of the tube and the time when the anode output reaches the peak amplitude. In measurement, the whole photocathode is illuminated. J: Also called transit time jitter. This is the fluctuation in electron transit time between individual pulses in the signal photoelectron mode, and may be defined as the FWHM of the frequency distribution of electron transit times. K: Hysteresis is temporary instability in anode current after light and voltage are applied. ANODE CURRENT A: Averaged over any interval of 30 seconds maximum. B: The light source is a tungsten filament lamp operated at a distribution temperature of 2856K. Supply voltage is 100 V between the cathode and all other electrodes connected together as anode. C: Red/White ratio is the quotient of the cathode current measured using a red filter (Toshiba R-68) interposed between the light source and the tube by the cathode current measured with the filter removed under the same conditions as Note B. D: The value is cathode output current when a blue filter (Corning CS 5-58 polished to 1/2 stock thickness) is interposed between the light source and the tube under the same condition as Note B. E: Measured with the same light source as Note B and with the voltage distribution ratio shown in Table 1 below. 5 6 7 (minutes) lmax. lmin. li TPMSB0002EA × 100 (%) (1) Light Hysteresis The tube is operated at 750 V with an anode current of 1 µA for 5 minutes. The light is then removed from the tube for a minute. The tube is then re-illuminated by the previous light level for a minute to measure the variation. (2) Voltage Hysteresis The tube is operated at 300 V with an anode current of 0.1 µA for 5 minutes. The light is then removed from the tube and the supply voltage is quickly increased to 800 V. After a minute, the supply voltage is then reduced to the previous value and the tube is re-illuminated for a minute to measure the variation. Figure 2: Anode Luminous Sensitivity and Gain Characteristics 105 TPMSB0175EB Figure 3: Typical Time Response 108 100 TPMSB0004EC 80 60 104 107 TRANS IT TIME 20 103 102 TYPICAL ANODE SENSITIVITY 105 TIME (ns) 106 10 8 6 4 MINIMUM ANODE SENSITIVITY 101 RISE T IME 104 2 100 500 103 1500 1000 700 Figure 4: Typical ENI with Wavelength TPMSB0176EA 10-12 10-13 10-14 10-15 10-16 100 200 300 400 500 600 WAVELENGTH (nm) 1 500 700 1000 SUPPLY VOLTAGE (V) SUPPLY VOLTAGE (V) EQUIVALENT NOISE INPUT (W) 40 GAIN ANODE LUMINOUS SENSITIVITY (A/lm) TYPICAL GAIN 700 800 1500 PHOTOMULTIPLIER TUBES R7517 Figure 5: Dimensional Outline and Basing Diagram (Unit: mm) Figure 6: Socket (Unit: mm) E678-11A 28.5 ± 1.5 49 8 MIN. T9 BULB Sold Separately 38 5 DY6 6 7 DY2 3.5 8 DY8 5 9 DY9 2 10 P 1 11 29 K DY1 DIRECTION OF LIGHT 18 80 MAX. DY7 DY3 3 94 MAX. 49.0 ± 0.25 24 MIN. DY4 4 4 DY5 33 PHOTOCATHODE Bottom View (Basing Diagram) 32.2 ± 0.5 11 PIN BASE JEDEC No.B11-88 TACCA0064EA TPMSA0005EB Figure 7: D Type Socket Assembly (Unit: mm) Sold Separately E717-63 E717-74 HOUSING (INSULATOR) 10 P R10 9 DY8 8 DY7 C2 R8 C1 26.0±0.2 4 5 R1 to R10 : 330 kΩ C1 to C3 : 10 nF DY4 A G 2.7 0.7 R5 31.0 ± 0.5 4 R4 HOUSING (INSULATOR) POTTING COMPOUND DY3 3 2 DY1 K 1 ° 10 R2 22.4±0.2 K 8 30° -HV AWG22 (VIOLET) C3 R9 C2 R8 C1 7 DY6 6 DY5 5 R6 R5 DY4 4 DY3 3 DY2 2 DY1 K 1 R1 to R10 : 330 kΩ C1 to C3 : 10 nF R4 R3 0.7 R1 11 DY8 R10 R7 SIDE VIEW R3 DY2 9 DY7 TOP VIEW 2 R6 DY9 32.0±0.5 7 6 SIGNAL OUTPUT (A) GND (G) 10 7 DY6 DY5 30.0 +0 -1 R9 SOCKET PIN No. P R7 29.0 ± 0.3 450 ± 10 C3 PMT 14.0±0.5 38.0 ± 0.3 49.0 ± 0.3 DY9 SIGNAL GND SIGNAL OUTPUT RG-174/U(BLACK) POWER SUPPLY GND AWG22 (BLACK) 26.0±0.2 SOCKET PIN No. 32.0±0.5 PMT 3.5 33.0 ± 0.3 5 R2 R1 11 -HV (K) 4- 2.8 R13 * "Wiring diagram applies when -HV is supplied." To supply +HV,connect the pin "G" to+HV, and the pin "K" to the GND. BOTTOM VIEW TACCA0002EH * Hamamatsu also provides C4900 series compact high voltage power supplies and C6270 series DP type socket assemblies which incorporate a DC to DC converter type high voltage power supply. TACCA0277EA Warning–Personal Safety Hazards Electrical Shock–Operating voltages applied to this device present a shock hazard. WEB SITE www.hamamatsu.com HAMAMATSU PHOTONICS K.K., Electron Tube Division 314-5, Shimokanzo, Iwata City, Shizuoka Pref., 438-0193, Japan, Telephone: (81)539/62-5248, Fax: (81)539/62-2205 U.S.A.: Hamamatsu Corporation: 360 Foothill Road, P. O. Box 6910, Bridgewater. N.J. 08807-0910, U.S.A., Telephone: (1)908-231-0960, Fax: (1)908-231-1218 E-mail: [email protected] Germany: Hamamatsu Photonics Deutschland GmbH: Arzbergerstr. 10, D-82211 Herrsching am Ammersee, Germany, Telephone: (49)8152-375-0, Fax: (49)8152-2658 E-mail: [email protected] France: Hamamatsu Photonics France S.A.R.L.: 19, Rue du Saule Trapu, Parc du Moulin de Massy, 91882 Massy Cedex, France, Telephone: (33)1 69 53 71 00, Fax: (33)1 69 53 71 10 E-mail: [email protected] United Kingdom: Hamamatsu Photonics UK Limited: 2 Howard Court, 10 Tewin Road Welwyn Garden City Hertfordshire AL7 1BW, United Kingdom, Telephone: 44-(0)1707-294888, Fax: 44(0)1707-325777 E-mail: [email protected] North Europe: Hamamatsu Photonics Norden AB: Smidesvägen 12, SE-171-41 SOLNA, Sweden, Telephone: (46)8-509-031-00, Fax: (46)8-509-031-01 E-mail: [email protected] Italy: Hamamatsu Photonics Italia: S.R.L.: Strada della Moia, 1/E, 20020 Arese, (Milano), Italy, Telephone: (39)02-935 81 733, Fax: (39)02-935 81 741 E-mail: [email protected] TPMS1059E02 JUL. 2006. IP