3.0x2.0mm SURFACE MOUNT LED LAMP Part Number: AA3020ARWC/Z PRELIMINARY SPEC WHITE ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Description The source color devices are made with InGaN Light Emitting Diode. Static electricity and surge damage the LEDS. Features z It is recommended to use a wrist band or anti-electrostatic 3.0MM X 2.0MM, 1.4MM HIGH, ONLY MINIMUM All devices, equipment and machinery must be electrically SPACE REQUIRED. z glove when handling the LEDs. SUITABLE FOR COMPACT OPTOELECTRONIC grounded. APPLICATIONS. z LOW POWER CONSUMPTION. Applications z PACKAGE : 2000PCS / REEL. z traffic signaling. z MOISTURE SENSITIVITY LEVEL : LEVEL 4. z backlighting (illuminated advertising , general lighting). z ELECTROSTATIC z TYP. DISCHARGE THRESHOLD (HBM):1000V. COLOR TEMPERATURE: 6500K z COLOR COORDINATES:X=0.31,Y=0.31 ACC. TO z COLOR z RoHS z substitution of micro incandescent lamps. z reading lamps. z signal and symbol luminaire for orientation. CIE1931(WHITE). z OPTICAL z interior and exterior automotive lighting. EFFICIENCY: 51.6 lm/W(TYP.) REPRODUCTION INDEX: 80 z marker lights (e.g. steps, exit ways, etc). z decorative and entertainment lighting. z indoor and outdoor commercial and residential COMPLIANT. architectural lighting. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.25(0.01") unless otherwise noted. 3. Specifications are subject to change without notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAH5317 APPROVED: WYNEC REV NO: V.2 CHECKED: Allen Liu DATE: JUN/27/2007 DRAWN: Y.L.LI PAGE: 1 OF 8 ERP: 1201003012 Handling Precautions Compare to epoxy encapsulant that is hard and brittle, silicone is softer and flexible. Although its characteristic significantly reduces thermal stress, it is more susceptible to damage by external mechanical force. As a result, special handling precautions need to be observed during assembly using silicone encapsulated LED products. Failure to comply might leads to damage and premature failure of the LED. 1. Handle the component along the side surfaces by using forceps or appropriate tools. 2. Do not directly touch or handle the silicone lens surface. It may damage the internal circuitry. 3. Do not stack together assembled PCBs containing exposed LEDs. Outside impact may scratch the silicone lens or damage the internal circuitry. 4. During surface-mounting, the pickup capillary diameter should be larger than the silicone lens to insure the capillary does not scratch or damage the lens. SPEC NO: DSAH5317 APPROVED: WYNEC REV NO: V.2 CHECKED: Allen Liu DATE: JUN/27/2007 DRAWN: Y.L.LI PAGE: 2 OF 8 ERP: 1201003012 Selection Guide Note2 Dice Part No. AA3020ARWC/Z WHITE (InGaN) luminous Intensity Iv(mcd) @ 20mA Lens Type Note3 Viewing Note1 Angle Φv (mlm) @ 20mA Min. Typ. Min. Typ. 2 θ 1/2 650 1200 1500 3300 120 ° WATER CLEAR Absolute Maximum Ratings at TA=25°C Parameter Symbol Value Unit Power dissipation Pt 111 mW Reverse Voltage VR 5 V Junction temperature TJ 110 °C Operating Temperature Top -40 To +85 °C Storage Temperature Tstg -40 To +100 °C IF 30 mA IFM 100 mA Rth JA Rth JS 300 140 °C/W °C/W DC Forward Current Peak Forward Current Note4 Thermal resistance Note5 Junction/ambient Junction/solder point Notes: 1 .θ 1/2 is the angle from optical centerline where the luminous intensity is 1/2 the optical centerline value. 2.Luminous intensity is measured by a current pulse of 10ms at a tolerance of ±15%. 3.The typical data of Luminous Flux can only reflect statistical figures, actual parameters of individual product could differ from the typical data. For the purpose of product enhancement, the typical data is subject to change without prior notice. 4.1/10 Duty Cycle, 0.1ms Pulse Width. 5.Rth(J-A) Results from mounting on PC board FR4 (pad size ≥ 16 mm 2 per pad), Electrical / Optical Characteristics at TA=25°C Parameter Symbol Chromaticity coordinate x acc.to CIE1931 IF=20mA [Typ.] X Chromaticity coordinate y acc.to CIE1931 IF=20mA [Typ.] Y Note1 Note1 Forward Voltage IF=20mA [Min.] Forward Voltage IF=20mA [Typ.] Forward Voltage [Typ.] Reverse Current (VR=5V) [Max.] Unit 0.31 - 0.31 - 2.7 VF Note2 IF=20mA [Max.] Reverse Current (VR=5V) Value 3.2 V 3.7 0.01 μA IR 10 Temperature coefficient of x IF=20mA, -10 ° C≤ T≤100 ° C [Typ.] TC x -0.1 10-3 / ° C Temperature coefficient of y IF=20mA, -10 ° C≤ T≤100 ° C [Typ.] TCy -0.2 10-3 / ° C Temperature coefficient of VF IF=20mA, -10 ° C≤ T≤100 ° C [Typ.] TCV -2.5 mV/ ° C Notes: 1.Chromaticity coordinates are measured by a current pulse of 20ms with a tolerance of ±0.01 in X and Y color coordinates. 2.Forward voltage is measured with a current pulse of 10ms at a tolerance of ±0.1V. SPEC NO: DSAH5317 APPROVED: WYNEC REV NO: V.2 CHECKED: Allen Liu DATE: JUN/27/2007 DRAWN: Y.L.LI PAGE: 3 OF 8 ERP: 1201003012 Brightness codes Note1 luminous Intensity Iv(mcd) @ 20mA Φv (mlm) @ 20mA Code. Min. Max. Typ. T 650 1200 3260 U 900 1500 3350 V 1200 1800 3400 Note2 Notes: 1.Luminous intensity is measured by a current pulse of 10ms at a tolerance of ±15%. 2.The typical data of Luminous Flux can only reflect statistical figures, actual parameters of individual product could differ from the typical data. For the purpose of product enhancement, the typical data is subject to change without prior notice. White SPEC NO: DSAH5317 APPROVED: WYNEC AA3020ARWC/Z REV NO: V.2 CHECKED: Allen Liu DATE: JUN/27/2007 DRAWN: Y.L.LI PAGE: 4 OF 8 ERP: 1201003012 AA3020ARWC/Z SPEC NO: DSAH5317 APPROVED: WYNEC REV NO: V.2 CHECKED: Allen Liu DATE: JUN/27/2007 DRAWN: Y.L.LI PAGE: 5 OF 8 ERP: 1201003012 AA3020ARWC/Z White CIE 0.44 0.43 0.42 0.41 0.40 0.39 c1 0.38 0.37 0.36 b4 0.35 c0 0.34 0.33 b3 b1 0.32 0.31 b2 0.30 a1 0.29 0.28 a0 0.27 0.26 0.25 0.24 0.23 0.22 0.21 0.22 0.23 0.24 0.25 0.26 0.27 0.28 0.29 0.30 0.31 0.32 0.33 0.34 0.35 0.36 0.37 0.38 a0 a1 b1 X 0.264 0.283 0.296 0.280 X 0.248 0.275 0.283 0.264 X 0.283 0.330 0.330 0.287 Y 0.267 0.305 0.276 0.248 Y 0.286 0.321 0.305 0.267 Y 0.305 0.360 0.339 0.295 Reference CCT: 14000~9000k Reference CCT: 14000~9000k Reference CCT: 9000~5600k b2 b3 b4 X 0.287 0.330 0.330 0.296 X 0.275 0.298 0.306 0.283 X 0.298 0.321 0.330 0.306 Y 0.295 0.339 0.318 0.276 Y 0.321 0.350 0.332 0.305 Y 0.350 0.379 0.360 0.332 Reference CCT: 9000~5600k Reference CCT: 9000~7000k c0 c1 X 0.330 0.361 0.356 0.330 X 0.321 0.366 0.361 0.330 Y 0.360 0.385 0.351 0.318 Y 0.379 0.419 0.385 0.360 Reference CCT: 5600~4600k SPEC NO: DSAH5317 APPROVED: WYNEC Reference CCT: 7600~5600k Reference CCT: 6000~4600k REV NO: V.2 CHECKED: Allen Liu DATE: JUN/27/2007 DRAWN: Y.L.LI PAGE: 6 OF 8 ERP: 1201003012 AA3020ARWC/Z Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Tape Specifications (Units : mm) SPEC NO: DSAH5317 APPROVED: WYNEC Reel Dimension REV NO: V.2 CHECKED: Allen Liu DATE: JUN/27/2007 DRAWN: Y.L.LI PAGE: 7 OF 8 ERP: 1201003012 PACKING & LABEL SPECIFICATIONS SPEC NO: DSAH5317 APPROVED: WYNEC REV NO: V.2 CHECKED: Allen Liu AA3020ARWC/Z DATE: JUN/27/2007 DRAWN: Y.L.LI PAGE: 8 OF 8 ERP: 1201003012