TI SN65LVDS310

SN65LVDS310
www.ti.com
SLLS836 – MAY 2007
PROGRAMMABLE 27-BIT SERIAL-TO-PARALLEL RECEIVER
FEATURES
•
•
•
•
•
•
•
•
•
•
•
Serial Interface Technology
Compatible With FlatLink™ 3G Transmitters
(E.g., SN65LVDS305 or SN65LVDS307)
Supports Video Interfaces up to 24-Bit RGB
Data and 3 Control Bits Received Over One
SubLVDS Differential Data Line
SubLVDS Differential Voltage Levels
Up to 405-Mbps Data Throughput
Three Operating Modes to Conserve Power
– Active mode QVGA: 17 mW
– Typical Shutdown: 0.7 µW
– Typical Standby Mode: 67 µW Typical
ESD Rating > 4 kV (HBM)
Pixel-Clock Range of 4 MHz–15 MHz
Failsafe on All CMOS Inputs
Packaged in 4-mm × 4-mm MicroStar
Junior™µBGA® With 0,5-mm Ball Pitch
Very Low EMI
When receiving, the PLL locks to the incoming clock,
CLK, and generates an internal high-speed clock at
the line rate of the data lines. The data is serially
loaded into a shift register using the internal
high-speed clock. The deserialized data is presented
on the parallel output bus with a recreation of the
pixel clock, PCLK, generated from the internal
high-speed clock. If no input CLK signal is present,
the output bus is held static with PCLK and DE held
low, while all other parallel outputs are pulled high.
The F/S conrol input selects between a slow CMOS
bus output rise time for best EMI and power
consumption and a fast CMOS output for increased
speed or higher-load designs.
Flatlinkä3G
LCD
Driver
APPLICATIONS
•
•
•
LVDS310
Small Low-Emission Interface Between
Graphics Controller and LCD Display
Mobile Phones and Smart Phones
Portable Multimedia Players
CLK
DATA
LVDS307
DESCRIPTION
The SN65LVDS310 receiver deserializes FlatLink
3G-compliant serial input data to 27 parallel data
outputs. The SN65LVDS310 receiver contains one
shift register to load 30 bits from one serial input and
latches the 24 pixel bits and 3 control bits out to the
parallel CMOS outputs after checking the parity bit. If
a parity error is detected, the data output bus
disregards the newly received pixel. Instead, the last
data word is held on the output bus for another clock
cycle.
1
2
3
4
5
6
7
8
9
*
0
#
Application
Processor
with
RGB
Video
Interface
M0056-04
The serial data and clock are received via
sub-low-voltage differential signalling (SubLVDS)
lines. The SN65LVDS310 supports three operating
power modes (shutdown, standby, and active) to
conserve power.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
FlatLink, MicroStar Junior are trademarks of Texas Instruments.
µBGA is a registered trademark of Tessera, Inc.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2007, Texas Instruments Incorporated
SN65LVDS310
www.ti.com
SLLS836 – MAY 2007
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
DESCRIPTION (CONTINUED)
The RXEN input can be used to put the SN65LVDS310 in a shutdown mode. The SN65LVDS310 enters an
active standby mode if the common mode voltage of the CLK input becomes shifted to VDDLVDS (e.g.,
transmitter releases CLK output into high-impedance). This minimizes power consumption without the need of
switching an external control pin. The SN65LVDS310 is characterized for operation over ambient air
temperatures of –40°C to 85°C. All CMOS and SubLVDS signals are 2-V tolerant with VDD = 0 V. This feature
allows powering up I/Os before VDD is stabilized.
FUNCTIONAL BLOCK DIAGRAM
VDDLVDS
RBBDC
iPCLK
D0+
50
Parity
Check
SubLVDS
50
F/S
AND
D0–
8
8
G[0:7]
0
Output Buffer
27-Bit Parallel
Register
Serial-to-Parallel Conversion
R[0:7]
1
RGB = 1
HS = VS = 1
DE = 0
VDDLVDS
8
B[0:7]
HS
VS
Standby or
Pwr Down
DE
RBBDC
CLK+
´15
50
50
PLL
Multiplier
SubLVDS
CLK–
´1
0
PCLK
1
Standby
Vthstby
RXEN
Standby or
Pwr Down
Glitch
Suppression
Control
B0177-04
2
Submit Documentation Feedback
SN65LVDS310
www.ti.com
SLLS836 – MAY 2007
PINOUT – TOP VIEW
ZQC PACKAGE
(TOP VIEW)
1
2
3
4
5
6
7
B4
B6
B7
G1
G3
G5
GND
B2
B3
B5
G2
G4
G7
R0
B0
GND
G0
G6
R1
VDD
GNDPLLD
VDD
GNDPLLD
B1
R3
R5
R2
NC
NC
VDDPLLA
RXEN
PCLK
R7
R4
CLK–
D0+
VS
HS
R6
GNDPLLA
D0–
DE
VDD
F/S
A
B
C
D
E
F
GNDLVDS GNDLVDS
G
VDDLVDS
CLK+
P0063-03
Submit Documentation Feedback
3
SN65LVDS310
www.ti.com
SLLS836 – MAY 2007
PINOUT – TOP VIEW (continued)
Table 1. Numeric Terminal List
TERMINAL
4
SIGNAL
TERMINAL
SIGNAL
TERMINAL
SIGNAL
TERMINAL
SIGNAL
A1
B4
B7
R0
D6
R5
F5
VS
A2
B6
C1
B0
D7
R2
F6
HS
A3
B7
C2
GND
E1
NC
F7
R6
A4
G1
C3
–
E2
NC
G1
VDDLVDS
A5
G3
C4
G0
E3
VDDPLLA
G2
CLK+
A6
G5
C5
G6
E4
RXEN
G3
GNDPLLA
A7
GND
C6
R1
E5
PCLK
G4
D0–
B1
B2
C7
VDD
E6
R7
G5
DE
B2
B3
D1
GNDPLLD
E7
R4
G6
VDD
B3
B5
D2
VDD
F1
GNDLVDS
G7
F/S
B4
G2
D3
GNDPLLD
F2
GNDLVDS
B5
G4
D4
B1
F3
CLK–
B6
G7
D5
R3
F4
D0+
Submit Documentation Feedback
SN65LVDS310
www.ti.com
SLLS836 – MAY 2007
Table 2. TERMINAL FUNCTIONS
NAME
D0+, D0–
CLK+, CLK–
I/O
SubLVDS in
DESCRIPTION
SubLVDS data link
SubLVDS input pixel clock; polarity is fixed.
R0–R7
Red-pixel data (8)
G0–G7
Green-pixel data (8)
B0–B7
HS
Blue-pixel data (8)
CMOS out
Horizontal sync
VS
Vertical sync
DE
Data enable
PCLK
Output pixel clock (rising clock polarity)
Disables the CMOS drivers and turns off the PLL, putting device in shutdown mode
1 – Receiver enabled
0 – Receiver disabled (shutdown)
RXEN
CMOS In
Note: The RXEN input incorporates glitch suppression logic to avoid unwanted switching. The input
must be pulled low for longer than 10 µs continuously to force the receiver to enter shutdown. The input
must be pulled high for at least 10 µs continuously to activate the receiver. An input pulse shorter than
5 µs is interpreted as a glitch and becomes ignored. At power up, the receiver is enabled immediately if
RXEN = H and disabled if RXEN = L.
CMOS bus rise time select
F/S
1 – fast output rise time
0 – slow output rise time
VDD
Supply voltage
GND
Supply ground
VDDLVDS
SubLVDS I/O supply voltage
GNDLVDS
VDDPLLA
Power supply
SubLVDS ground
PLL analog supply voltage
GNDPLLA
PLL analog GND
VDDPLLD
PLL digital supply voltage
GNDPLLD
PLL digital GND
Submit Documentation Feedback
5
SN65LVDS310
www.ti.com
SLLS836 – MAY 2007
FUNCTIONAL DESCRIPTION
DESERIALIZATION MODE
The SN65LVDS310 receives payload data over a single SubLVDS data pair D0. The PLL locks to the SubLVDS
clock input and internally multiplies the clock by a factor of 30. The internal high-speed clock is used to shift in
the data payload on D0 and deserialize the data. Figure 1 illustrates the timing and the mapping of the data
payload into the 30-bit frame. The internal high-speed clock is divided by a factor of 30 to recreate the pixel
clock, and the data payload with the pixel clock is presented on the output bus. The reserved bits and parity bit
are not output. The PLL can lock to a clock that is in the range of 4 MHz through 15 MHz.
CLK–
CLK+
D0+/– CHANNEL res res CP R7 R6 R5 R4 R3 R2 R1 R0 G7 G6 G5 G4 G3 G2 G1 G0 B7 B6 B5 B4 B3 B2 B1 B0 VS HS DE res res CP R7 R6
T0161-01
Figure 1. Data and Clock Input
POWER-DOWN MODES
The SN65LVDS310 receiver has two power-down modes to facilitate efficient power management.
Shutdown Mode
A low input signal on the RXEN pin puts the SN65LVDS310 into shutdown mode. This turns off most of the
receiver circuitry, including the SubLVDS receivers, PLL, and deserializers. The SubLVDS differential-input
resistance remains 100 Ω, and any input signal is ignored. All outputs hold a static output pattern:
R[0:7] = G[0:7] = B[0:7] = VS = HS = high; DE = PCLK = low.
The current draw in shutdown mode is nearly zero if the SubLVDS inputs are left open or pulled high.
Standby Mode
The SN65LVDS310 enters the standby mode when the SN65LVDS310 is not in shutdown mode but the
SubLVDS clock-input common-mode voltage is above 0.9 × VDDLVDS. The CLK input incorporates pullup
circuitry. This circuit shifts the SubLVDS clock-input common-mode voltage to VDDLVDS in the absence of an
input signal. All circuitry except the SubLVDS clock-input standby monitor is shut down. The SN65LVDS310 also
enters the standby mode when the input clock frequency on the CLK input is less than 500 kHz. The SubLVDS
input resistance remains 100 Ω, and any input signal on the data inputs D0+ and D0– is ignored. All outputs
hold a static output pattern:
R[0:7] = G[0:7] = B[0:7] = VS = HS = high; DE = PCLK = low.
The current drawn in standby mode is very low.
ACTIVE MODES
A high input signal on RXEN combined with a CLK input signal switching faster than 3 MHz and VICM smaller
than 1.3 V forces the SN65LVDS310 into the active mode. Current consumption in the active mode depends on
operating frequency and the number of data transitions in the data payload. CLK-input frequencies between 3
MHz and 4 MHz activate the device, but proper PLL functionality is not assured.
Acquire Mode (PLL Approaches Lock)
When the SN65LVDS310 is enabled and a SubLVDS clock input is present, the PLL pursues lock to the input
clock. While the PLL pursues lock, the output data bus holds a static output pattern:
R[0:7] = G[0:7] = B[0:7] = VS = HS = high; DE = PCLK = low.
6
Submit Documentation Feedback
SN65LVDS310
www.ti.com
SLLS836 – MAY 2007
FUNCTIONAL DESCRIPTION (continued)
For proper device operation, the pixel clock frequency must fall within the valid fPCLK range specified under
recommended operating conditions. If the pixel clock frequency is higher than 3 MHz but lower than fPCLK(MIN),
the SN65LVDS310 PLL is enabled. Under such conditions, it is possible for the PLL to lock temporarily to the
pixel clock, causing the PLL monitor to release the device into the active receive mode. If this happens, the PLL
may or may not be properly locked to the pixel clock input, potentially causing data errors, frequency oscillation,
and PLL deadlock (loss of VCO oscillation).
Receive Mode
After the PLL achieves lock, the device enters the normal receive mode. The output data bus presents the
deserialized data. The PCLK output pin outputs the recovered pixel clock.
PARITY ERROR DETECTION AND HANDLING
The SN65LVDS310 receiver performs error checking on the basis of a parity bit that is transmitted across the
LVDS interface from the transmitting device. Once the SN65LVDS310 detects the presence of the clock and the
PLL has locked onto PCLK, then the parity is checked. Parity-error detection ensures detection of all single-bit
errors in one pixel and 50% of all multibit errors.
The parity bit covers the 27-bit data payload consisting of 24 bits of pixel data plus VS, HS, and DE. Odd-parity
bit signalling is used. If the sum of the 27 data bits and the parity bit is an odd number, the receive data are
assumed to be valid. If the sum is an even number, parity error is declared.
If a parity error is detected, then the data on that PCLK cycle is not output. Instead, the last valid data from a
previous PCLK cycle is repeated on the output bus. This is to prevent any bit error that occurs on the LVDS link
from causing perturbations in VS, HS, or DE that might be visually disruptive to a display.
The reserved bits are not covered in the parity calculations.
R[0:7], G[0:7],
B[0:7], HS, VS, DE
PCLK
When a parity error is
detected, the receiver outputs
the previous pixel on the
bus. Hence, no data transitions
occur.
T0163-02
Figure 2. Output Response When Parity Error Is Detected
Submit Documentation Feedback
7
SN65LVDS310
www.ti.com
SLLS836 – MAY 2007
FUNCTIONAL DESCRIPTION (continued)
STATUS-DETECT AND OPERATING-MODES FLOW DIAGRAM
The SN65LVDS310 switches between the power-saving and active modes in the following way:
Power Up
RXEN = 1
CLK Input Inactive
RXEN Low
for > 10 ms
Power Up
RXEN = 0
Shutdown
Mode
Standby
Mode
RXEN High
for > 10 ms
VICM(CLK) > 0.9 VDDLVDS
RXEN Low
for > 10 ms
VICM(CLK) > 0.9 VDDLVDS
or fCLK < 500 kHz
CLK Input Active
Power Up
RXEN = 1
CLK Active
RXEN Low
for > 10 ms
Receive
Mode
PLL Achieved Lock
Acquire
Mode
F0017-01
Figure 3. Operating Modes Flow Diagram
Table 3. Status Detect and Operating Modes Descriptions
MODE
CONDITIONS
RXEN is set low for longer than 10 µs.
(1) (2)
Least amount of power consumption (most circuitry turned
off); all outputs held static:
R[0:7] = G[0:7] = B[0:7] = VS = HS = high; DE = PCLK =
low
Standby mode
Low power consumption (standby monitor circuit active; PLL RXEN is high for longer than 10 µs and CLK inputs are
is shut down to conserve power);
common-mode, VICM(CLK) is above 0.9 × VDDLVDS, or
All outputs held static:
CLK inputs are floating (2)
R[0:7] = G[0:7] = B[0:7] = VS = HS = high; DE = PCLK =
low
Acquire mode
PLL pursues lock; all outputs held static:
R[0:7] = G[0:7] = B[0:7] = VS = HS = high; DE = PCLK =
low
RXEN is high; CLK input monitor detected clock input
common mode and woke up receiver from standby
mode.
Receive mode
Data transfer (normal operation);
receiver deserializes data and provides data on parallel
output
RXEN is high and PLL is locked to incoming clock.
(1)
(2)
8
CHARACTERISTICS
Shutdown mode
In shutdown mode, all SN65LVDS310 internal switching circuits (e.g., PLL, serializer, etc.) are turned off to minimize power
consumption. The input stage of any input pin remains active.
Leaving CMOS control inputs unconnected can cause random noise to toggle the input stage and potentially harm the device. All CMOS
inputs must be tied to a valid logic level, VIL or VIH, during shutdown or standby mode. Exceptions are the SubLVDS inputs CLK and D0,
which can be left unconnected while not in use.
Submit Documentation Feedback
SN65LVDS310
www.ti.com
SLLS836 – MAY 2007
Table 4. Operating Mode Transitions
MODE TRANSITION
USE CASE
TRANSITION SPECIFICS
Shutdown → standby
Drive RXEN high to enable
receiver.
1. RXEN high > 10 µs
2. Receiver enters standby mode.
a. R[0:7] = G[0:7] = B[0:7] = VS = HS remain high and DE = PCLK low
b. Receiver activates clock input monitor.
Standby → acquire
Transmitter activity
detected
1. CLK input monitor detects clock input activity.
2. Outputs remain static.
3. PLL circuit is enabled.
Acquire → receive
Link is ready to receive
data.
1. PLL is active and approaches lock.
2. PLL achieves lock within twakeup.
3. Input D0 becomes active.
4. First data word is recovered.
5. Parallel output bus turns on switching from a static output pattern to output the
first valid data word.
Receive → standby
Receiver requested to enter
standby mode by input
common-mode voltage
VICM > 0.9 VDDLVDS (e.g.,
transmitter output clock
enters high-impedance
state)
1. Transmitter disables outputs within tsleep.
2. RX Input monitor detects VICM > 0.9 VDDLVDS.
3. R[0:7] = G[0:7] = B[0:7] = VS = HS transition to high and DE = PCLK to low on
next falling PLL clock edge.
4. PLL shuts down.
5. Clock activity input monitor remains active.
Receive/standby →
shutdown
Turn off receiver.
1. RXEN is pulled low for > tpwrdn.
2. Receiver switches all outputs to the high-impedance state.
3. Most IC circuitry is shut down for least power consumption.
ABSOLUTE MAXIMUM RATINGS (1)
VALUE
UNIT
Supply voltage range, VDD (2), VDDPLLA, VDDPLLD, VDDLVDS
–0.3 to 2.175
V
Voltage range at any input When VDDx > 0 V
or output terminal
When VDDx ≤ 0 V
–0.5 to 2.175
–0.5 to VDD + 2.175
±4
Human body model (3) (all pins)
Electrostatic discharge
Charged-device model (4) (all pins)
±1500
Machine model (5) (all pins)
±200
Continuous power dissipation
(2)
(3)
(4)
(5)
kV
V
See Dissipation Ratings table
±5
Ouput current, IO
(1)
V
mA
Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute maximum-rated conditions for extended periods may affect device reliability.
All voltage values are with respect to the GND terminals.
In accordance with JEDEC Standard 22, Test Method A114-B
In accordance with JEDEC Standard 22, Test Method C101
In accordance with JEDEC Standard 22, Test Method A115-A
DISSIPATION RATINGS
(1)
(2)
PACKAGE
CIRCUIT
BOARD MODEL
TA < 25°C
DERATING FACTOR (1)
ABOVE TA = 25°C
TA = 85°C
POWER RATING
ZQC
Low-K (2)
496 mW
6.21 mW/°C
124 mW
This is the inverse of the junction-to-ambient thermal resistance when board-mounted and with no air
flow.
In accordance with the low-K thermal metric definitions of EIA/JESD51-2.
Submit Documentation Feedback
9
SN65LVDS310
www.ti.com
SLLS836 – MAY 2007
DEVICE POWER DISSIPATION
PARAMETER
Device power
dissipation
PD
TEST CONDITIONS
TYP
VDDx = 1.8 V, TA = 25°C, all outputs terminated with 10 pF, fCLK at 4 MHz
MAX
16.8
VDDx = 1.95 V, TA = –40°C, all outputs terminated with 10 pF, fCLK at 15 MHz
48.8
UNIT
mW
RECOMMENDED OPERATING CONDITIONS (1)
VDD
VDDPLLA
VDDPLLD
VDDLVDS
Supply voltages
VDDn(PP)
Supply voltage noise magnitude
TA
Operating free-air temperature
MIN
TYP
MAX
UNIT
1.65
1.8
1.95
V
Test set-up shown in Figure 5;
fCLK ≤ 50 MHz; f(noise) = 1 Hz to 2 GHz
100
fCLK > 50 MHz; f(noise) = 1 Hz to 1 MHz
100
fCLK > 50 MHz; f(noise) > 1 MHz
mV
40
–40
85
°C
CLK+ and CLK–
fCLK±
Input pixel clock frequency
tDUTCLK
CLK input duty cycle
See Figure 1
4
15
MHz
500
kHz
35
65
%
|VD0+ – VD0–|, |VCLK+ – VCLK–|
during normal operation
70
200
mV
Receive or acquire mode
0.6
1.2
Standby mode (2), see Figure 14
D0+, D0–, CLK+, and CLK–
|VID|
Magnitude of differential input
voltage
VICM
Input voltage common-mode range
∆VICM
Input voltage common-mode
variation among all SubLVDS inputs
VICM(n) – VICM(m) with n = D0 or CLK and m
= D0 or CLK
–100
100
∆VID
Differential input voltage amplitude
variation among all SubLVDS inputs
VID(n) – VID(m) with n = D0 or CLK and m =
D0 or CLK
–10%
10%
tr/f
Input rise or fall time
RXEN at VDD; see Figure 8
∆tr/f
Input rise or fall time mismatch
among all SubLVDS inputs
tr(n) – tr(m) and tf(n) – tf(m) with n = D0 or CLK
and m = D0 or CLK
Standby mode
0.9 VDDLVDS
V
mV
800
ps
–100
100
ps
0.7 VDD
VDD
V
0
0.3 VDD
RXEN, F/S
VICMOSH
High-level input voltage
VICMOSL
Low-level input voltage
tinRXEN
RXEN input pulse duration
V
µs
10
R[7:0], G[7:0], B[7:0], VS, HS, PCLK
CL
(1)
(2)
10
Output load capacitance
10
pF
Unused single-ended inputs must be held high or low to prevent them from floating.
PCLK input frequencies lower than 500 kHz force the SN65LVDS310 into standby mode. Input frequencies between 500 kHz and 3
MHz may or may not activate the SN65LVDS310. Input frequencies beyond 3 MHz activate the SN65LVDS310. Input frequencies
between 500 kHz and 4 MHz are not recommended, and can cause PLL malfunction.
Submit Documentation Feedback
SN65LVDS310
www.ti.com
SLLS836 – MAY 2007
DEVICE ELECTRICAL CHARACTERISTICS
over recommended operating conditions (unless otherwise noted)
PARAMETER
Alternating 1010 test pattern (see Table 7); all CMOS outputs terminated with 10
pF; F/S and RXEN at VDD; VIH = VDD, VIL = 0 V; VDD = VDDPLLA = VDDPLLD =
VDDLVDS
IDD
RMS supply
current
Typical power test pattern (see Table 6); VID = 70 mV, all CMOS outputs
terminated with 10 pF; F/S at GND and RXEN at VDD; VIH = VDD, VIL = 0 V;
VDD = VDDPLLA = VDDPLLD = VDDLVDS
CLK and D inputs are left open; all control inputs held static high or low;
All CMOS outputs terminated with 10 pF;
VIH = VDD, VIL = 0 V; VDD = VDDPLLA = VDDPLLD = VDDLVDS
(1)
TYP (1)
MAX
fPCLK = 4 MHz
9.8
14
fPCLK = 6 MHz
11.7
15.9
fPCLK = 15 MHz
19.3
25
fPCLK = 4 MHz
4.7
TEST CONDITIONS
MIN
fPCLK = 6 MHz
UNIT
mA
6
fPCLK = 15 MHz
13.2
Standby mode;
RXEN = VIH
15
100
Shutdown
mode;
RXEN = VIL
0.4
10
µA
All typical values are at 25°C and with 1.8-V supply, unless otherwise noted.
INPUT ELECTRICAL CHARACTERISTICS
over operating free-air temperature range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP (1)
MAX
UNIT
D0+, D0–, CLK+, and CLK–
Vthstby
Input voltage common-mode threshold to
switch between receive/acquire mode and RXEN at VDD
standby mode
1.3
VTHL
Low-level differential input voltage
threshold
–40
0.9 VDDLVDS
V
mV
VD0+– VD0–, VCLK+ – VCLK–
VTHH
High-level differential input voltage
threshold
II+, II–
Input leakage current
VDD = 1.95 V; VI+ = VI–;
VI = 0.4 V or VI = 1.5 V
IIOFF
Power-off input current
VDD = GND; VI = 1.5 V
RID
Differential input termination resistor value
CIN
Input capacitance
∆CIN
Input capacitance variation
78
Measured between input terminal
and GND
100
mV
75
µA
–75
µA
122
Ω
1
Within one signal pair
pF
0.2
Between all signals
RBBDC Pullup resistor for standby detection
40
1
21
30
39
pF
kΩ
RXEN, F/S
VIK
Input clamp voltage
IICMOS Input
current (2)
II = –18 mA, VDD = VDD(min)
–1.2
V
0 V ≤ VDD ≤ 1.95 V; VI = GND or
VI = 1.95 V
100
nA
CIN
Input capacitance
IIH
High-level input current
VIN = 0.7 VDD
–200
200
nA
IIL
Low-level input current
VIN = 0.3 VDD
–200
200
nA
VIH
High-level input voltage
0.7 VDD
VDD
V
VIL
Low-level input voltage
0
0.3 VDD
V
(1)
(2)
2
pF
All typical values are at 25°C and with 1.8-V supply unless otherwise noted.
Do not leave any CMOS input unconnected or floating to minimize leakage currents. Every input must be connected to a valid logic
level, VIH or VOL, while power is supplied to VDD.
Submit Documentation Feedback
11
SN65LVDS310
www.ti.com
SLLS836 – MAY 2007
OUTPUT ELECTRICAL CHARACTERISTICS
over operating free-air temperature range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
0.8 VDD
VDD
V
0
0.2 VDD
V
R[0:7], G[0:7], B[0:7], VS, HS, PCLK
VOH
High-level output current
VOL
Low-level output current
IOH
High-level output current
IOL
Low-level output current
F/S = L, IOH = –250 µA
F/S = H, IOH = –500 µA
F/S = L, IOL = 250 µA
F/S = H, IOL = 500 µA
F/S = L
–250
F/S = H
–500
µA
F/S = L
250
F/S = H
500
µA
SWITCHING CHARACTERISTICS
over recommended operating conditions (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP (1)
MAX
UNIT
800
ps
–100
100
ps
F/S = L
8
16
F/S = H
4
8
D0+, D0–, CLK+, and CLK–
tr/f
Input rise and fall times
RXEN at VDD; see Figure 8
∆tr/f
Input rise or fall time
mismatch between all
SubLVDS inputs
tr(n) – tr(m) and tf(n) – tf(m) with n = D0 or CLK and m =
D0 or CLK
R[7:0], G[7:0], B[7:0], VS, HS, PCLK
tr/f
Rise and fall time
20%–80% of VDD
tOUTP
PCLK output duty cycle
tOSK
Output skew between PCLK
and R[0:7], G[0:7], B[0:7],
HS, VS, and DE
(2)
CL = 10 pF (3); see Figure 7
45%
See Figure 7.
50%
–500
ns
55%
500
ps
2.5/fPCLK
s
3.8
µs
INPUT-TO-OUTPUT RESPONSE TIME
tPD(L)
Propagation delay time from
CLK+ input to PCLK output
RXEN at VDD, VIH = VDD, VIL = GND, CL = 10 pF, see
Figure 12
tGS
RXEN glitch suppression
pulse duration (4)
VIH = VDD, VIL = GND, RXEN toggles between VIL and
VIH; see Figure 13 and Figure 14.
tpwrup
Enable time from power
down (↑RXEN)
Time from RXEN pulled high to data outputs enabled and
transmit valid data; see Figure 14.
2
ms
tpwrdn
Disable time from active
mode (↓RXEN)
RXEN is pulled low during receive mode; time
measurement until all outputs held static: R[0:7] = G[0:7]
= B[0:7] = VS = HS = high, DE = PCLK = low and PLL is
shut down; see Figure 14.
11
µs
twakeup
Enable time from standby
(↑↓CLK)
RXEN at VDD; device is in standby; time measurement
from CLK input starts switching to PCLK and data
outputs enabled and transmit valid data; see Figure 15.
2
ms
Disable time from active
mode (CLK transitions to
high-impedance)
RXEN at VDD; device is receiving data; time
measurement from CLK input signal stops (input open or
input common mode VICM exceeds threshold voltage
Vthstby) until all outputs held static:
R[0:7] = G[0:7] = B[0:7] = VS = HS = high;
DE = PCLK = low and PLL is shut down;
see Figure 15.
3
µs
tsleep
(1)
(2)
(3)
(4)
12
1.4/fPCLK
1.9/fPCLK
All typical values are at 25°C and with 1.8-V supply, unless otherwise noted.
tr/f depends on the F/S setting and the capacitive load connected to each output. Some application information of how to calculate tr/f
based on the output load and how to estimate the timing budget to interconnect to an LCD driver are provided in the application section
near the end of this data sheet.
The output rise and fall times are optimized for an output load of 10 pF. The rise and fall times can be adjusted by changing the output
load capacitance.
The RXEN input incorporates glitch-suppression logic to disregard short input pulses. tGS is the duration of either a high-to-low or
low-to-high transition that is suppressed.
Submit Documentation Feedback
SN65LVDS310
www.ti.com
SLLS836 – MAY 2007
SWITCHING CHARACTERISTICS (continued)
over recommended operating conditions (unless otherwise noted)
PARAMETER
(5)
TEST CONDITIONS
MAX
0.087 fPCLK
UNIT
MHz
When using the SN65LVDS310 receiver in conjunction with the SN65LVDS307 transmitter in one link, the PLL bandwidth of the
SN65LVDS310 receiver always exceeds the bandwidth of the SN65LVDS307 transmit PLL. This ensures stable PLL tracking under all
operating conditions and maximizes the receiver skew margin.
12
10.0
11
9.5
RX PLL BW
10
9
9%
8.5%
8.2%
8
7.7%
7
6
PLL Bandwidth – %
PLL BW [% of PCLK Frequency]
TYP (1)
MIN
PLL bandwidth (5)
fBW
4 MHz
9%
9.0
8.5
Spec Limit
8.0
15 MHz
8.1 %
TX PLL BW
7.5
5
7.0
4
0
100
200
300
400
0
5
PLL Frequency − MHz
10
15
20
PCLK Frequency – MHz
G001
Figure 4. SN65LVDS310 PLL Bandwidth (Also Showing the SN65LVDS307 PLL Bandwidth)
TIMING CHARACTERISTICS
PARAMETER
tRSKMx
(1) (2)
(1)
(2)
(3)
(4)
(5)
Receiver input skew
margin; see (3) and
Figure 29
TEST CONDITIONS
x = 0..29, fPCLK = 15 MHz; RXEN fCLK = 15 MHz (4)
at VDD, VIH = VDD, VIL = GND,
fCLK = 4 MHz to 15
RL = 100 Ω, test setup as in
MHz (5)
Figure 6, test pattern as in
Table 9
MIN
MAX
UNIT
630
1
- 480 ps
2 · 30 · fCLK
ps
Receiver input skew margin (tRSKM) is the timing margin available for transmitter output pulse position (tPPOS), interconnect skew, and
interconnect inter-symbol interference. tRSKM represents the remainder of the serial bit time not taken up by the receiver strobe
uncertainty. tRSKM assumes a bit error rate better than 10–12.
tRSKM is inversely proportional to the internal setup and hold time uncertainty, ISI, and duty-cycle distortion from the front-end receiver,
the skew missmatch between CLK and data D0, as well as the PLL cycle-to-cycle jitter.
This includes the receiver internal setup and hold time uncertainty, all PLL-related high-frequency random and deterministic jitter
components that impact the jitter budget, ISI and duty-cycle distortion from the front-end receiver, and the skew between CLK and data
D0; the pulse position minimum/maximum variation is given with a bit error rate target of 10–12; measurements of the total jitter are taken
over >1012 samples.
The minimum and maximum limits are based on statistical analysis of the device performance over process, voltage, and temperature
ranges.
These minimum and maximum limits are simulated only.
Submit Documentation Feedback
13
SN65LVDS310
www.ti.com
SLLS836 – MAY 2007
PARAMETER MEASUREMENT INFORMATION
1
1
Noise
Generator
100 mV
VDDPLLA
2
SN65LVDS310
VDDPLLD
VDD
10 mF
VDDLVDS
GND
1.8-V
Supply
Note: The generator regulates the
noise amplitude at point 1 to the
target amplitude given under the table
Recommended Operating Conditions
S0216-05
Figure 5. Power-Supply Noise Test Setup
To measure tRSKM CLK is advanced or delayed with respect to data until errors are observed at the receiver outputs. The advance
or delay is then reduced until there are no data errors observed over 10
tRSKM
Programmable Delay
CLK and Data
Pattern
Generator
–12
serial bit times. The magnitude of the advance or delay
CLK
D1
DUT:
SN65LVDS310
D2
Bit Error
Detector
D3
Ideal Receiver Strobe Position
tPG_ERROR
tRSKM(p)
C
tRSKM(n)
tbit
tRSKM
– is the smaller of the two measured values tRSKM(p) and tRSKM(n)
tPG_ERROR – Test equipment (pattern generator) intrinsic output pulse position timing uncertainty
tbit
– serial bit time
C
– LVDS310 set-up and hold-time uncertainty
Note: C can be derived by subtracting the receiver skew margin tRSKM(p) + tRSKM(p) from one serial bit time
T0164-04
Figure 6. Receiver Jitter-Budget Test Setup
14
Submit Documentation Feedback
SN65LVDS310
www.ti.com
SLLS836 – MAY 2007
PARAMETER MEASUREMENT INFORMATION (continued)
tf
t setup
80% (VOH -V OL )
R[7:0], G[7:0],
B[7:0], HS, VS, DE
20% (VOH -V OL )
t hold
t OSK
tr
VOH
80% (VOH -V OL )
PCLK
50% (VOH
- –VOL)
20% (VOH -VOL )
VOL
tr
tf
Note:
The Set-up and Hold-time of CMOS outputs R[7:0], G[7:0],
B[7:0], HS, VS, and DE in relation to PCLK can be
calulated by:
1
tS&H =
2 -rPCLK -tREF - tOSK - DtDUTP
T0256-01
Figure 7. Output Rise/Fall, Setup/Hold Time
VD0+ – VD0– , VCLK+ – VCLK–
tf
80%(VID)
100%(VIC)
tr
0V
20%(VID)
0%(VID)
T0167-03
Figure 8. SubLVDS Differential Input Rise and Fall Time Defintion
CLK+, D0+
VDDLVDS
RID/2
RBBDC
Gain
Stage
RID/2
CLK–, D0–
Standby
Detection
Line End
Termination
ESD
S0224-03
Figure 9. Equivalent Input Circuit Design
Submit Documentation Feedback
15
SN65LVDS310
www.ti.com
SLLS836 – MAY 2007
PARAMETER MEASUREMENT INFORMATION (continued)
IICMOS
RXEN, F/S
CMOS Input
(VI+ + VI–)/2
II+
VICMOS
CLK+, D0+
VID
RGB, VS,
HS, PCLK
IO
II–
CLK–, D0–
VICM
VI+
VO
VI–
SubLVDS Input
CMOS Output
S0217-04
Figure 10. I/O Voltage and Current Definition
RGB, VS,
HS, PCLK
VO
SN65LVDS310
CL=10 pF
S0218-04
Figure 11. CMOS Output Test Circuit, Signal, and Timing Definition
16
Submit Documentation Feedback
SN65LVDS310
www.ti.com
SLLS836 – MAY 2007
PARAMETER MEASUREMENT INFORMATION (continued)
Pixel(n–1)
R7(n–1)
R7(n–2)
D0+
R7 R6 R5 R4
Pixel(n)
Pixel(n+1)
R7(n)
R7(n+1)
CP R7
CP R7
CLK–
CLK+
tPD(L)
VDD/2
PCLK
Pixel(n–1)
CMOS Data Out
R7
R7(n–3)
R7(n–1)
R6
R6(n–3)
R6(n–1)
T0168-02
Figure 12. Propagation Delay, Input to Output
VDD/2
RXEN
tGS
CLK
tPLL
VCO Internal Signal
PLL Approaches Lock
tpwrup
PCLK
R[7:0], G[7:0], B[7:0], VS, HS
DE
T0257-01
Figure 13. Receiver Phase-Locked Loop Set Time and Receiver Enable Time
Submit Documentation Feedback
17
SN65LVDS310
www.ti.com
SLLS836 – MAY 2007
PARAMETER MEASUREMENT INFORMATION (continued)
3 ms
<20 ns
Glitch Shorter
Than tGS Will Be
Ignored
2 ms
Less Than 20 ns
Spike Will be
Rejected
Glitch Shorter
Than tGS Will Be
Ignored
RXEN
tpwrup
tpwrdn
CLK+
tGS
ICC
tGS
PCLK
Receiver Disabled
(OFF)
Receiver Aquires Lock
Receiver Enabled
(ON)
Receiver
Disabled
(OFF)
Receiver
Turns OFF
T0254-01
Figure 14. Receiver Enable/Disable Glitch Suppression Time
CLK
twakeup
tsleep
PCLK
R[7:0], G[7:0], B[7:0], VS, HS,
Receiver Disabled
(OFF)
Receiver Aquires Lock,
Outputs Still Disabled
RX Enabled
Output Data Valid
RX Enabled;
Output Data
Invalid
RX
Disabled
(OFF)
T0255-01
Figure 15. Standby Detection
POWER-CONSUMPTION TESTS
Table 5 shows an example test pattern word.
Table 5. Example Test Pattern Word
WORD
R[7:4], R[3:0], G[7:4], G[3:0], B[7:4], B[3:0], 0, VS, HS, DE
1
7
0x7C3E1E7
C
3
E
1
R7 R6 R5 R4 R3 R2 R1 R0 G7 G6 G5 G4 G3 G2 G1 G0 B7
0
18
1
1
1
1
1
0
0
0
0
1
1
1
1
1
0
E
7
B6
B5
B4
B3
B2
B1
B0
0
0
0
1
1
1
1
0
0
0
Submit Documentation Feedback
VS HS DE
1
1
1
SN65LVDS310
www.ti.com
SLLS836 – MAY 2007
TYPICAL IC POWER-CONSUMPTION TEST PATTERN
The typical power-consumption test pattern consists of 16 30-bit transmit words. The pattern repeats itself
throughout the entire measurement. It is assumed that every possible transmit code on RGB inputs has the
same probability to occur during typical device operation.
Table 6. Typical IC Power-Consumption Test Pattern
WORD
TEST PATTERN:
R[7:4], R[3:0], G[7:4], G[3:0], B[7:4], B[3:0], 0, VS, HS, DE
1
0x0000007
2
0xFFF0007
3
0x01FFF47
4
0xF0E07F7
5
0x7C3E1E7
6
0xE707C37
7
0xE1CE6C7
8
0xF1B9237
9
0x91BB347
10
0xD4CCC67
11
0xAD53377
12
0xACB2207
13
0xAAB2697
14
0x5556957
15
0xAAAAAB3
16
0xAAAAAA5
MAXIMUM POWER-CONSUMPTION TEST PATTERNS
The maximum (or worst-case) power consumption of the SN65LVDS310 is tested using the two different test
patterns shown in Table 7 and Table 8. Test patterns consist of 16 30-bit transmit words. The pattern repeats
itself throughout the entire measurement. It is assumed that every possible transmit code on RGB inputs has the
same probability to occur during typical device operation.
Table 7. Worst-Case Power-Consumption
Test Pattern 1
WORD
TEST PATTERN:
R[7:4], R[3:0], G[7:4], G[3:0], B[7:4], B[3:0], 0, VS, HS, DE
1
0xAAAAAA5
2
0x5555555
Table 8. Worst-Case Power-Consumption
Test Pattern 2
WORD
TEST PATTERN:
R[7:4], R[3:0], G[7:4], G[3:0], B[7:4], B[3:0], 0, VS, HS, DE
1
0x0000000
2
0xFFFFFF7
OUTPUT SKEW PULSE POSITION and JITTER PERFORMANCE
The test pattern of Table 9 is used to measure the output skew pulse position and the jitter performance of the
SN65LVDS310. The jitter test pattern stresses the interconnect, particularly to test for ISI, using very long
run-lengths of consecutive bits, and incorporating very high and low data rates, maximizing switching noise.
Each pattern is self-repeating for the duration of the test.
Submit Documentation Feedback
19
SN65LVDS310
www.ti.com
SLLS836 – MAY 2007
Table 9. Transmit Jitter Test Pattern
WORD
20
TEST PATTERN:
R[7:4], R[3:0], G[7:4], G[3:0], B[7:4], B[3:0], 0, VS, HS, DE
1
0x0000001
2
0x0000031
3
0x00000F1
4
0x00003F1
5
0x0000FF1
6
0x0003FF1
7
0x000FFF1
8
0x0F0F0F1
9
0x0C30C31
10
0x0842111
11
0x1C71C71
12
0x18C6311
13
0x1111111
14
0x3333331
15
0x2452413
16
0x22A2A25
17
0x5555553
18
0xDB6DB65
19
0xCCCCCC1
20
0xEEEEEE1
21
0xE739CE1
22
0xE38E381
23
0xF7BDEE1
24
0xF3CF3C1
25
0xF0F0F01
26
0xFFF0001
27
0xFFFC001
28
0xFFFF001
29
0xFFFFC01
30
0xFFFFF01
31
0xFFFFFC1
32
0xFFFFFF1
Submit Documentation Feedback
SN65LVDS310
www.ti.com
SLLS836 – MAY 2007
TYPICAL CHARACTERISTIC CURVES
Some of the plots in this section show more than one curve representing various device pin relationships. Taken together,
they represent a working range for the tested parameter.
QUIESCENT SUPPLY CURRENT vs TEMPERATURE
SUPPLY CURRENT vs FREQUENCY
100.0
40
35
STANDBY
30
10.0
IDD - mA
IDDQ - mA
25
F/S = 1, jitter test
20
F/S = 1,
typ pwr
F/S = 0, jitter test
15
1.0
10
POWERDOWN
0.1
-50
5
F/S = 0, typ pwr
0
0
-30
-10
10
30
50
Temperature - °C
70
5
90
Figure 16.
RECEIVER STROBE POSITION vs TEMPERATURE
20
PLL BANDWIDTH
10.0
Limit with RSKM = 130 ps
400
9.5
350
PLL Bandwidth – %
FL3G Limit
300
t(RSPOS)
15
Figure 17.
450
250
200
11 MHz (HVGA)
150
100
50
0
-40
10
f - Frequency - MHz
9.0
8.5
Spec Limit
8.0
7.5
-20
0
20
40
Temperature - °C
60
80
7.0
0
5
10
15
20
PCLK Frequency – MHz
Figure 18.
Figure 19.
Submit Documentation Feedback
21
SN65LVDS310
www.ti.com
SLLS836 – MAY 2007
TYPICAL CHARACTERISTIC CURVES (continued)
PCLK CYCLE-TO-CYCLE OUTPUT JITTER
1000
900
CC Jitter - ps
800
700
600
500
400
0
5
10
Frequency - MHz
15
20
Figure 20.
RSKM vs BIT RATE
2000
Receiver Strobe
Position uncertainty
1500
T(PPOS )
1000
Additional interconnect margin
RSKM - ps
500
225
Minimum desired interconnect budget
0
-225-
-500
-1000
-1500
-2000
120
170
220
270
320
370
420
dR - Mbps
Bit width
Trskm
Trskm - Tppos
Figure 21.
22
Submit Documentation Feedback
225ps
SN65LVDS310
www.ti.com
SLLS836 – MAY 2007
TYPICAL CHARACTERISTIC CURVES (continued)
INPUT COMMON-MODE NOISE REJECTION vs
FREQUENCY
QVGA OUTPUT WAVEFORM
0.0
249
-4.0
-6.0
0
CMNR - dB
Output Voltage Amplitude - mV
-2.0
190
f(PCLK) = 5.5 MHz
-8.0
-10.0
-12.0
-14.0
-16.0
–190
-18.0
-20.0
0
–251
1 ns/div
Response Over 80-inch of FR-4 + 1m Coax Cable
200 400 600 800 1000 1200 1400 1600 1800 2000
Frequency - MHz
Figure 22.
Figure 23.
INPUT RETURN LOSS
INPUT DIFFERENTIAL CROSSTALK vs FREQUENCY
0.0
0.0
-10.0
Differential Xtalk - dB
-20.0
-30.0
-40.0
-20.0
-30.0
-40.0
-50.0
-60.0
-50.0
-70.0
-60.0
-80.0
0
200 400 600 800 1000 1200 1400 1600 1800 2000
Frequency - MHz
0
200 400 600 800 1000 1200 1400 1600 1800 2000
Frequency - MHz
Figure 24.
Figure 25.
PHASE NOISE
-50
-60
-70
-80
-90
f(PCLK) = 65 MHz
-100
dBc/Hz
Differential S11 - dB
-10.0
-110
-120
-130
-140
-150
-160
-170
-180
1
10
100
1k
10k
100k
1M
10M
FREQUENCY - Hz
Figure 26.
Submit Documentation Feedback
23
SN65LVDS310
www.ti.com
SLLS836 – MAY 2007
APPLICATION INFORMATION
PREVENTING INCREASED LEAKAGE CURRENTS IN CONTROL INPUTS
A floating (left open) CMOS input allows leakage currents to flow from VDD to GND. Do not leave any CMOS
input unconnected or floating. Every input must be connected to a valid logic level, VIH or VOL, while power is
supplied to VDD. This also minimizes the power consumption of standby and power-down modes.
POWER-SUPPLY DESIGN RECOMMENDATION
For a multilayer PCB, it is recommended to keep one common GND layer underneath the device and connect all
ground terminals directly to this plane.
SN65LVDS310 DECOUPLING RECOMMENDATION
The SN65LVDS310 was designed to operate reliably in a constricted environment with other digital switching
ICs. In cell phone designs, the SN65LVDS310 often shares a power supply with various other ICs. The
SN65LVDS310 can operate with power-supply noise as specified in the (1) To minimize the power-supply noise
floor, provide good decoupling near the SN65LVDS310 power pins. The use of four ceramic capacitors (two
0.01-µF and two 0.1-µF) provides good performance. At the very least, it is recommended to install one 0.1-µF
and one 0.01-µF capacitor near the SN65LVDS310. To avoid large current loops and trace inductance, the trace
length between the decoupling capacitors and IC power input pins must be minimized. Placing the capacitor
underneath the SN65LVDS310 on the bottom of the PCB is often a good choice.
VGA APPLICATION
Figure 27 shows a possible implementation of a 640 × 480 VGA display. The SN65LVDS307 innterfaces to the
SN65LVDS310, which is the corresponding receiver device, to deserialize the data and drive the display driver.
The pixel-clock rate of 5.5 MHz assumes ~10% blanking overhead and a 60-Hz display refresh rate. The
application assumes 24-bit color resolution. Also shown is how the application processor provides a power-down
(reset) signal for both the serializer and the display driver. The signal count over the flexible printed circuit board
(FPC) could be further decreased by using the automatic standby detection feature of the SN65LVDS310 and
pulling RXEN permanently high.
2 ´ 0.1 mF
2 ´ 0.1 mF
FPC
165 Mbps
RXEN
SN65LVDS310
LS
TXEN
5.5 MHz
PCLK
R[7:0]
G[7:0]
B[7:0]
HS, VS, DE
SN65LVDS307
SPI
CLK+
CLK–
D0+
D0–
Video Mode Display
Driver
27
LCD With VGA
Resolution
5.5 MHz
R[7:0]
G[7:0]
B[7:0]
HS, VS, DE
RESET
GND
GND
ENABLE
27
GND
SPI
PCLK
D[23:0]
HS, VS, DE
1.8 V
CLK+
CLK–
D0+
D0–
5.5 MHz
Pixel CLK
1.8 V
VDDx
VDDx
Application
Processor
(e.g. OMAP)
2 ´ 0.01 mF
GND
2 ´ 0.01 mF
TXEN can also be pulled-up
high with a resistor if no
RESET signal is available from
the application processor
Serial Port Interface
(3-Wire IF)
If FPC wire count is critical, replace this
connection with a pull-up resistor at RXEN
3
B0178-04
Figure 27. Typical VGA Display Application
(1)
24
Unused single-ended inputs must be held high or low to prevent them from floating.
Submit Documentation Feedback
SN65LVDS310
www.ti.com
SLLS836 – MAY 2007
APPLICATION INFORMATION (continued)
TYPICAL APPLICATION FREQUENCIES
The SN65LVDS310 supports pixel clock frequencies from 4 MHz to 15 MHz. Table 10 provides a few typical
display resolution examples. The blanking overhead is assumed to be 20%. Often, blanking overhead is smaller,
resulting in a lower data rate.
Table 10. Typical Application Data Rates and Serial Lane Usage
Display Screen
Resolution
Visible Pixel
Count
Blanking
Overhead
Display
Refresh Rate
[Hz}
Pixel Clock Frequency on CLK
[MHz]
Serial Data
Rate [Mbps]
240 × 320 (QVGA)
76,800
20%
60
5.5
166
640 × 200
128,000
9.2
276
352 × 416 (CIF+)
146,432
10.5
316
352 × 440
154,880
11.2
335
320 × 480 (HVGA)
153,600
30
5.5
166
320 × 480 (HVGA)
153,600
60
11.1
332
800 × 250
200,000
14.4
432
640 × 320
204,800
14.7
442
640 × 480 (VGA)
307,200
11.1
332
30
CALCULATION EXAMPLE: HVGA DISPLAY
Display resolution:
480 × 320
Frame refresh rate:
58.4 Hz
Vertical visible pixels:
320 lines
Vertical front porch:
10 lines
Vertical sync:
5 lines
Vertical back porch:
3 lines
Horizontal visible pixels:
480 columns
Horizontal front porch:
20 columns
Horizontal sync:
5 columns
Horizontal back porch:
3 columns
Hsync = 5
HBP
The following calculation shows an example for a half-VGA display with the following parameters:
Visible Area = 480 Column
HFP = 20
Vsync = 5
VBP = 3
Visible Area
= 320 Lines
VFP = 10
Visible Area
Entire Display
M0086-01
Figure 28. HVGA Display
Calculation of the total number of pixel and blanking overhead:
Visible area pixel count:
480 × 320 = 153,600 pixels
Total frame pixel count:
(480 + 20 + 5 + 3) × (320 + 10 + 5 + 3) = 171,704 pixels
Blanking overhead:
(171,704 – 153,600) ÷ 153,600 ≈ 11.8 %
The application requires the following serial-link parameters:
Pixel clock frequency:
171,704 × 58.4 Hz = 10 MHz
Serial data rate:
10 MHz × 30 bits = 300 Mbps
Submit Documentation Feedback
25
SN65LVDS310
www.ti.com
SLLS836 – MAY 2007
HOW TO DETERMINE INTERCONNECT SKEW AND JITTER BUDGET
Designing a reliable data link requires examining the interconnect skew and jitter budget. The sum of all
transmitter, PCB, connector, FPC, and receiver uncertainties must be smaller than the available serial bit time.
The highest pixel clock frequency defines the available serial bit time. The transmitter timing uncertainty is
defined by tPPOS in the transmitter data sheet. For a bit-error-rate target of ≤ 10–12, the measurement duration for
tPPOS is ≥ 1012. The SN65LVDS310 receiver can tolerate a maximum timing uncertainty defined by tRSKM. The
interconnect budget is calculated by:
tinterconnect = tRSKM – tPPOS
Example:
fPCLK(max) = 11 MHz (HVGA display resolution, 60 Hz)
tPPOS(SN65LVDS305) = 330 ps
Target bit error rate: 10–12
tRSKM(SN65LVDS310) = 1/(2 × 30 × fPCLK) – 480 ps = 1035 ps
The interconnect budget for cable skew and ISI must be smaller than:
tinterconnect = tRSKM– tPPOS = 1035 ps – 330 ps = 705 ps
tinterconnect = tRSKM– tPPOS
Ideal t PPosn data transition
Serial bit width (1/dR)
D0
t PPosn(max)
t PPosn(min)
Ideal receiver strobe position
tinterconnect
tinterconnect
RX internal sampling clock
tRSPosn(min)
tRSPosn(max)
tppos: Transmitter output pulse position (min and max)
RSKM: Receiver Skew Margin
RSPosn: Receiver input strobe position (min and max)
t PPosx (max) -t PPosx(min) = TJ TXPLL(non-trackable) + tTXskew + tTXDJ
The interconnect budget compensates for:
RSKM = SKEW PCB + XTALK PCB + ISIPCB
RSPosn(max) - RSPosn(min) = SkewRX + S&HRX + TJ (RXPLL(non-trackable)
TJTXPLL(non-trackable): : non-trackable TX PLL jitter; this is
mainly cycle-to-cycle PLL jitter, which can not be
compensated for at the R PLL
tTXskew: : transmitter output skew (skew between CLK
and data)
tTXIDJ Transmitter Deterministic Jitter of TX output
stage (includes TX Intersymbol Interference ISI)
SKEWPCB: : PCB induced Skew
(trace + connector);
XTALKPCB: : PCB induced cross-talk;
SkewRX: Receiver input skew (skew between CLK and Dx input)
S&HRX: Receiver input latch Sample & Hold uncertainty
TJ(RXPLL(non-trackable): : Intrinsic RX PLL jitter above RX PLL
bandwidth; PLLTJ > f(BWRX); TJ=RJ[ps-rms]*14 + DJ[ps]
ISIPCB: : Inter-symbol interference of PCB;
is dependent on interconnect frequency
loss; may be zero for short interconnects.
T0165-04
Figure 29. Jitter Budget
F/S-PIN SETTING AND CONNECTING THE SN65LVDS310 TO AN LCD DRIVER
NOTE:
Receiver PLL tracking: To maximize the design margin for the interconnect, good
RX PLL tracking of the TX PLL is important. FlatLink 3G connection requires the RX
PLL to have a bandwidth higher than the bandwidth of the TX PLL. The
SN65LVDS310 PLL design is optimized to track the SN65LVDS307 PLL particularly
well, thus providing a very large receiver skew margin. A FlatLink 3G-compliant link
must provide at least ±225 ppm of receiver skew margin for the interconnect.
26
Submit Documentation Feedback
SN65LVDS310
www.ti.com
SLLS836 – MAY 2007
It is important to understand the tradeoff between power consumption, EMI, and maximum speed when selecting
the F/S signal. It is beneficial to choose the slowest rise time possible to minimize EMI and power consumption.
Unfortunately, a slower rise time also reduces the timing margin left for the LCD driver. Hence, it is necessary to
calculate the timing margin to select the correct F/S pin setting.
The output rise time depends on the output driver strength and the output load. An LCD driver typical capacitive
load is assumed with ~10 pF. The higher the capacitive load, the slower is the rise time. Rise time of the
SN65LVDS310 is measured as the time duration it takes the output voltage to rise from 20% of VDD to 80% of
VDD, and fall time is defined as the time for the output voltage to transition from 80% of VDD to 20% of VDD.
The rise time of the output stage is fixed and does not adjust to the pixel frequency. Only changing the F/S
setting changes the output rise time. Due to the short bit time at very fast pixel clock speeds and the real
capacitive load of the display driver, the output amplitude might not reach VDD and GND saturation fully. To
ensure sufficient signal swing and verify the design margin, it is necessary to determine that the output
amplitude under any circumstance reaches the display driver’s input stage logic threshold (usually 30% and 70%
of VDD).
HOW TO DETERMINE THE LCD DRIVER TIMING MARGIN
To determine the timing margin, it is necessary to specify the frequency of operation, identify the setup and hold
times of the LCD driver, and specify the output load of the SN65LVDS310 as a combination of the LCD driver
input parasitics plus any capacitance caused by the connecting PCB trace. Furthermore, the setting of pin F/S
and the SN65LVDS310 output skew impact the margin. The total remaining design margin calculates as follows:
t rise(max) C LOAD
1
t DM +
* t DUTP(max_error) *
* Ťt OSKŤ
2 ƒ PCLK
10 pF
(2)
where:
tDM – design margin
fPCLK – pixel clock frequency
tDUTP(max_error) – maximum duty cycle error
trise(max) – maximum rise or fall time; see tr/f under switching characteristics
CL – parasitic capacitance (sum of LCD driver input parasitics + connecting PCB trace)
tskew – clock-to-data output skew, SN65LVDS310
Example:
At a pixel clock frequeny of 11 MHz (HVGA), and an assumed LCD driver load of 15 pF, the remaining timing
margin is:
t DUTP(max_error) +
t DM +
2
ŤtDUTP(max) * 50%Ť
100%
1
* 9 ns *
5.5 MHz
t PCLK + 5%
100%
16 ns (FńS+GND)
10 pF
1
+ 4.5 ns
11 MHz
15 pF
* 500 ps + 16 ns
As long as the setup and hold times of the LCD driver are BOTJ less than 16 ns, the timing budget is met
sufficiently.
Submit Documentation Feedback
27
PACKAGE OPTION ADDENDUM
www.ti.com
26-Sep-2007
PACKAGING INFORMATION
Orderable Device
Status (1)
SN65LVDS310ZQCR
ACTIVE
BGA MI
CROSTA
R JUNI
OR
ZQC
48
2500 Green (RoHS &
no Sb/Br)
SNAGCU
Level-3-260C-168 HR
SN65LVDS310ZQCT
ACTIVE
BGA MI
CROSTA
R JUNI
OR
ZQC
48
250
SNAGCU
Level-3-260C-168 HR
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
Green (RoHS &
no Sb/Br)
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
16-Feb-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
SN65LVDS310ZQCR
BGA MI
CROSTA
R JUNI
OR
ZQC
48
2500
330.0
12.4
4.3
4.3
1.5
8.0
12.0
Q1
SN65LVDS310ZQCT
BGA MI
CROSTA
R JUNI
OR
ZQC
48
250
330.0
12.4
4.3
4.3
1.5
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
16-Feb-2012
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
SN65LVDS310ZQCR
BGA MICROSTAR
JUNIOR
ZQC
48
2500
338.1
338.1
20.6
SN65LVDS310ZQCT
BGA MICROSTAR
JUNIOR
ZQC
48
250
338.1
338.1
20.6
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Mobile Processors
www.ti.com/omap
Wireless Connectivity
www.ti.com/wirelessconnectivity
TI E2E Community Home Page
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated