150, 200 WATTS 300, 400 WATTS (PFC AVAILABLE) WIDE RANGE ADJUSTABLE MULTIPLE OUTPUTS ZPS-150 ZPS-200 ZPS-300 ZPS-400 Featuring: • Models rated at 150 W, 200 W, 300 W and 400 W continuous power (180 W, 240 W, 360 W and 480 W peak power respectively) • An auto-ranging input (ZPS-150 A, 200 A) or jumper selectable input (ZPS-300 A, 400 A) or power factor corrected, wide range input (ZPS300 AP, 400 AP) for 115 V or 230 V, 47-65Hz, single phase AC • Typical power factor of 0.99 (ZPS300 AP, 400 AP) • Four independently isolated and regulated outputs • Wide range of adjustability on auxiliary outputs (up to 3.3:1) • Up to 50% greater peak currents on auxiliary outputs • Low ripple and noise on all outputs • Typical 70%-75% efficiency • Meets international safety requirements • Meets international Class B EMI requirements (except for ZPS300 AP which meets Class A) • DC Power good signal • Remote start (Enable) and remote sense features • Optional cover available • Medically approved version available STANDARD ZPS SERIES MODEL PWR PFC ZPS-150A 150 ZPS-200A 200 ZPS-300A 300 ZPS-300AP ZPS-400A 400 ZPS-400AP OUTPUT #1 OUTPUT #2 4.75V To 5.25V 11.5V To 25.2V NO @ @ 2A To 20A 0.3A To 3A/4.5A pk 4.75V To 5.25V 11.5V To 25.2V NO @ @ 3A To 30A 0.4A To 4A/6A pk NO 4.75V To 5.25V 11.5V To 25.2V @ @ YES 4.5A To 45A 0.6A To 6A/9A pk NO 4.75V To 5.25V 11.5V To 25.2V @ @ YES 5.5A To 55A 0.7A To 7A/10.5A pk Flexibility is the key word for these models. Since all four outputs are independently isolated and regulated, they can be connected as required to meet the needs of the system. Outputs can be connected in either polarity or stacked to obtain greater voltages. An outstanding feature of these models is the wide range adjustability of the auxiliary outputs (up to 3.3:1). The user can adjust the auxiliary outputs to meet almost any combination of voltage requirements from 4.75 V to 25.2 V. Most of the models provide a wide input range OUTPUT #3 9.5V To 15.8V @ 0.3A To 4A/5A pk 9.5V To 15.8V @ 0.4A To 5A/6A pk 4.75V To 15.8V @ 0.8A To 8A/12A pk 4.75V To 15.8V @ 1A To 10 A/15A pk OUTPUT #4 4.75V To 12.6V @ 0.2A To 2A 4.75V To 12.6V @ 0.2A To 2A 4.75V To 15.8V @ 0.4A To 4A/6A pk 4.75V To 15.8V @ 0.6A To 6A/9A pk for operation anywhere in the world. Two of the models feature power factor corrected inputs to meet the international standards for input current harmonics. All models are fully approved to international safety and EMI standards (including the CE low voltage directive), simplifying approvals at the system level. All models feature highly reliable designs to ensure years of trouble free operation. Condor D.C. Power Supplies, Inc., A subsidiary of SL Industries, Inc. 805-486-4565 • (800) 235-5929 Fax: (805) 487-8911 http://www.condorpower.com 150, 200 WATTS 11”x 5”x 2.5” ZPS-150A, 200A, 250A, 300A 300, 400 WATTS (PFC AVAILABLE) 13”x 6”x 2.5” ZPS-400A ZPS-150A, 200A ZPS-250A, 250AP, 300A, 300AP ZPS-400A, 400AP 4.0 lbs - 1.8 kgs 5.0 lbs - 2.3 kgs 7.0 lbs - 3.2 kgs Dimensions: Inches Millimeters SPECIFICATIONS: ALL MODELS INPUT AC Input: Auto-ranging (ZPS-150A & 200A) or Jumper selectable (ZPS-300 A & 400 A) or power factor corrected wide range (ZPS-300AP & 400AP)- input for 115 V or 230 Vac, 47-65Hz internally fused with appropriate fuses (6A-10A) Power Factor: Typical 0.99 for ZPS-300AP & 400AP. Meets EN 61000-3-2. Inrush: Cold start AC current is less than 70 A peak for one half cycle of applied power at 230 Vac, limited by a thermistor. Brownout Protection: Holds regulation to 85 Vac. Hold-up Time: 20 ms @ after removal of power at nominal line and full load. Efficiency: 70%-75% typical OUTPUT Adjustability: Output #1 is adjustable ±5%. Wide range on auxiliary outputs up to 3.3:1 (see table). Line Load Cross Regulation: ± 0.6% on all outputs, over AC input range and loads within the ranges specified in the table. Ripple & Noise: Less than 1% p-p on all outputs. Remote Sense Compensates for 250 mV total line drop. Open sense lead protection. Temperature Coefficient: 0.03% per degree C. Stability: 0.1% over 8 hours after 30 minutes warm up. Transient Response: Output voltage returns to within 1% in less than 500 µSec for a 25% load change. Peak transient does not exceed 3%. Overload Protection: All outputs protected against short circuit. Input cycling off/on is required to reset latched-off protection mode. Overvoltage Protection (Output #1): Protects against power supply induced overvoltage. Trip point is factory set so that the output does not exceed 6.4 V. Peak output Current: Peak current should be limited to a maximum of 15 seconds. Enable: TTL level ”0” or contact closure to the ve-sense line inhibits DC outputs. DC Power Good: Provides a TTL level “1” when output #1 is above 4.6 V nominal. ENVIRONMENTAL Thermal Protection: Automatic shutdown if power supply temperature exceeds 90° C. Temperature Range: 0° C to 40° C at full ratings. Output power linearly derated by 1.7% per deg. C over 50° C to 70° C. Safety Agencies: UL 1950, CSA C 22.2 234 level 5, VDE 0805 /EN 60950, CE marking to low voltage directive. Conducted EMI: All models except ZPS-300AP, meet FCC Part 15 Subpart J, Class B, VDE 0871/B, EN 55022/B. ZPS-300AP meets Class A. Output Isolation: Isolated from ground at 50 Vdc. Cooling: 5 CFM ZPS-150, 15 CFM ZPS-200, 25 CFM ZPS-300 & 300AP, 30 CFM ZPS-400, 35 CFM ZPS-400AP. Forced air required to achieve full ratings. OPTIONS: Option “C”: Available with an enclosed cover Option “M”: Intended for MEDICAL APPLICATIONS Approved to UL 544, IEC 601/VDE 0750 safety and MDS-201-0004 EMI. Leakage Current is less than 500 µA. Option “AP”: For 300 watt and 400 watt power supplies, Power Factor corrected. AC INPUT (90-264 VAC Continuous Range Except ZPS-300A, 400A which require input jumpers to be set for 115V or 230V) 115V 230V Neutral Line 2 Line Line 1 Safety Ground TB1-(1) TB1-(2) TB1-(3) CONNECTOR Barrier strip #6-32 screws 0.375” centers DC OUTPUT FUNCTION Output #1 MODEL ZPS-150A & ZPS-200A ZPS-300A/AP & 400A/AP Output #2 ZPS-150A & ZPS-200A ZPS-300A/AP & 400A/AP Output #3 ZPS-150A & ZPS-200A ZPS-300A/AP & 400A/AP Output #4 ZPS-150A & ZPS-200A ZPS-300A /AP & 400A/AP LOCATION TB2-1 TB-22 TB4-1 TB4-2 TB3-1 TB3-2 TB2-3 TB2-4 TB3-3 TB3-4 TB2-5 TB2-6 TB3-5 TB3-6 TB2-7 TB2-8 NOTES 4.75V-5.25V Rtn (Isolated) 4.75V-5.25V Rtn (Isolated) 11.5V-25.2V Rtn (Isolated) 11.5V-25.2V Rtn (Isolated) 9.5V-15.8V Rtn (Isolated) 4.75V-15.8V Rtn (Isolated) 4.75V-12.6V Rtn (Isolated)) 4.75V-15.8V Rtn (Isolated) CONNECTOR Bus bars #8-32 screws Barrier Strip #6-32 Screws .375” centers STATUS AND CONTROL FUNCTION MODEL ZPS-150A & ZPS-200A Enable ZPS-300A/AP & ZPS-400A/AP DC Power Good ZPS-150A & ZPS-200A ZPS-300A/AP & ZPS-400A/AP Remote Sense ZPS-150A & ZPS200A ZPS-300A/AP & ZPS-400A/AP Consult factory for other available options. ZPS-300A, 300AP ZPS-400A, 400AP 115V 230V Line Line 1 Neutral Line 2 Safety Ground ZPS-150A & ZPS-200A FUNCTION LOCATION J1-1 J1-2 J3-1 J3-2 J1-4 J1-3 J3-4 J3-3 J2-2 J2-1 TB2-1 TB2-2 NOTES Enable Output #1 Rtn Enable Output #1 Rtn DC Power Good Output #1 Rtn DC Power Good Output #1 Rtn Output #1 Sense+ Output #1 SenseOutput #1 Sense+ Output #1 Sense- CONNECTOR Molex Part # 22-23-2041 Mates with Molex Part # 22-01-3047 Molex Part # 22-23-2021Mates with 22-01-3027 Barrier Strip # 6-32 Screws .375” Centers Condor D.C. Power Supplies, Inc., A subsidiary of SL Industries, Inc. 805-486-4565 • (800) 235-5929 Fax: (805) 487-8911 http://www.condorpower.com