SLES150 − OCTOBER 2005
D VCO (Voltage-Controlled Oscillator):
D
D
D
D
− Complete Oscillator Using Only One
External Bias Resistor (RBIAS)
− Lock Frequency:
13 MHz to 32 MHz (VDD = 3 V +5%,
TA = –205C to 755C, x1 Output)
13 MHz to 35 MHz (VDD = 3.3 V +5%,
TA = –205C to 755C, x1 Output)
15 MHz to 55 MHz (VDD = 5 V +5%,
TA = –205C to 755C, x1 Output)
− Selectable Output Frequency
D PFD (Phase Frequency Detector):
High Speed, Edge-Triggered Detector
with Internal Charge Pump
Independent VCO, PFD Power-Down Mode
Thin Small-Outline Package (14 Terminal)
CMOS Technology
Pin Compatible TLC2932IPW
14-PIN TSOP (PW PACKAGE)
(TOP VIEW)
LOGIC VDD
SELECT
VCO OUT
FIN −A
FIN −B
PFD OUT
LOGIC GND
1
2
3
4
5
6
7
14
13
12
11
10
9
8
VCO VDD
RBIAS
VCO IN
VCO GND
VCO INHIBIT
PFD INHIBIT
TEST
description
The TLC2932A is designed for phase-locked loop (PLL) systems and is composed of a voltage-controlled
oscillator (VCO) and an edge-triggered type phase frequency detector (PFD). The oscillation frequency range
of the VCO is set by an external bias resistor (RBIAS). The VCO has a 1/2 frequency divider at the output stage.
The high speed PFD with internal charge pump detects the phase difference between the reference frequency
input and signal frequency input from the external counter. Both the VCO and the PFD have inhibit functions,
which can be used as power-down mode. Due to the TLC2932A high speed and stable oscillation capability,
the TLC2932A is suitable for use as a high-performance PLL.
AVAILABLE OPTIONS
PACKAGE
TA
SMALL OUTLINE (PW)
–20°C to 75°C
TLC2932AIPW
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright 2005, Texas Instruments Incorporated
!!"# $%&!# '" (" %"#) $'#" %"("*$"+ '!"#! % % '"
#$"!!# " %"#) )*#+ ",# #&"# "#"("# '" )' !')" %#!&" '"#" $%&!# -'& !"+
TI.COM
1
SLES150 − OCTOBER 2005
functional block diagram
FIN−A
FIN−B
PFD INHIBIT
VCO IN
4
Phase
Frequency
Detector
5
9
6
BIAS
PFD OUT
VCO INHIBIT
SELECT
12
13
10
Voltage
Controlled
Oscillator
3
VCO OUT
2
Terminal Functions
TERMINAL
I/O
DESCRIPTION
NAME
NO.
LOGIC VDD
1
SELECT
2
I
VCO output frequency select. When SELECT is high, the VCO output frequency is ×1/2 and when
low. The output frequency is ×1.
VCO OUT
3
O
VCO output. When the VCO INHIBIT is high, VCO output is low.
FIN−A
4
I
Input reference frequency f(REF IN) is applied to FIN−A.
FIN−B
5
I
Input for VCO external counter output frequency f(FIN−B). FIN−B is nominally provided from the
external counter.
PFD OUT
6
O
PFD output. When the PFD INHIBIT is high, PFD output is in the high-impedance state.
LOGIC GND
7
TEST
8
PFD INHIBIT
9
I
PFD inhibit control. When PFD INHIBIT is high, PFD output is in the high-impedance state.
VCO INHIBIT
10
I
VCO inhibit control. When VCO INHIBIT is high, VCO output is low.
Power supply for the internal logic. This power supply should be separated from VCO VDD to reduce
cross-coupling between supplies.
GND for the internal logic.
Connect to GND.
VCO GND
11
VCO IN
12
I
GND for VCO.
VCO control voltage input. Nominally the external loop filter output connects to VCO IN to control
VCO oscillation frequency.
RBIAS
13
I
Bias supply. An external resistor (RBIAS) between VCO VDD and RBIAS supplies bias for adjusting the
oscillation frequency range.
VCO VDD
14
Power supply for VCO. This power supply should be separated from LOGIC VDD to reduce
cross-coupling between supplies.
2
TI.COM
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SLES150 − OCTOBER 2005
detailed description
VCO oscillation frequency
The VCO oscillation frequency is determined by an external register (RBIAS) connected between the VCO VDD
and the BIAS terminals. The oscillation frequency and range depends on this resister value. For the lock
frequency range refer to the recommended operating conditions. Figure 1 shows the typical frequency variation
and VCO control voltage.
VCO Oscillation Frequency − fOSC
VCO Oscillation Frequency Range
Bias Resistor (RBIAS)
1/2 VDD
VCO Control Voltage (VCO IN)
Figure 1. Oscillation Frequency
VCO output frequency 1/2 divider
The TLC2932A SELECT terminal sets the fOSC VCO output frequency as shown in Table 1. The 1/2 fOSC output
should be used for minimum VCO output jitter.
Table 1. VCO Output 1/2 Divider Function
SELLECT
VCO OUTPUT
Low
fOSC
1/2 fOSC
High
VCO inhibit function
The VCO has an externally controlled inhibit function which inhibit the VCO output. A high level on the VCO
INHIBIT terminal stops the VCO oscillation and powers down the VCO. The output maintains a low level during
the power−down mode as shown in Table 2.
Table 2. VCO Inhibit Function
VCO INHIBIT
VCO OSCILLATOR
VCO OUT
Low
Active
Active
IDD(VCO)
Normal
High
Stopped
Low level
Power Down
PFD operation
The PFD is a high-speed, edge-triggered detector with an internal charge pump. The PFD detects the phase
difference between two frequency inputs supplied to FIN−A and FIN−B as shown in Figure 2. Normally the
reference is supplied to FIN−A and the frequency from the external counter output is fed to FIN−B. For clock
recovery PLL system, other types of phase detectors should be used.
TI.COM
3
SLES150 − OCTOBER 2005
FIN−A
FIN−B
VOH
PFD OUT
HI-Z
VOL
Figure 2. PFD Function Timing Chart
PFD inhibit control
A high level on the PFD INHIBIT terminal places PFD OUT in the high-impedance state and the PFD stops
phase detection as shown in Table 3. A high level on the PFD INHIBIT terminal can also be used as the
power-down mode for the PFD.
Table 3. VCO Output Control Function
PFD INHIBIT
DETECTION
PFD OUT
Low
Active
Active
IDD(PFD)
Normal
High
Stopped
Hi−Z
Power Down
VCO block schematic
PFD block schematic
Charge Pump
VDD
FIN−A
PFD OUT
Detector
FIN−B
PFD INHIBIT
4
TI.COM
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SLES150 − OCTOBER 2005
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage (each supply), VDD (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Input voltage range (each input), VIN (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to VDD + 0.5 V
Input current (each input), IIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20 mA
Output current (each output), IO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20 mA
Operating free-air temperature range, TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –20°C to 75°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltages are with respect to GND.
2. For operation above 25_C free-air temperature, derate linearly at the rate of 5.6 mW/°C.
recommended operating conditions
PARAMETERS
VDD = 3 V
Supply voltage (each supply, see Note 3)
VDD = 3.3 V
VDD = 5 V
Input voltage, (inputs except VCO IN)
Output current, (each output)
VCO control voltage at VCO IN
Lock frequency
VDD = 3 V
VDD = 3.3 V
VDD = 5 V
VDD = 3 V
MIN
2.85
TYP
3
MAX
3.15
UNIT
3.135
3.3
3.465
V
4.75
5
5.25
0
0
0.9
13
VDD
±2
VDD
32
V
mA
V
13
35
MHz
15
55
2.2
5.1
VDD = 3.3 V
2.2
5.1
kΩ
VDD = 5 V
2.2
5.1
NOTE 3: It is recommended that the logic supply terminal (LOGIC VDD) and the VCO supply terminal (VCO VDD) should be at the same voltage
and separated from each other.
Bias Resisitor
electrical characteristics, VDD = 3 V, TA = 25°C (unless otherwise noted)
VCO section
PARAMETER
TEST CONDITIONS
VOH
VOL
High level output voltage
VTH
II
Input threshold voltage at select, VCO inhibit
ZI(VCOIN)
IDD(INH)
VCO IN input impedance
VI = VDD or GND
VCO IN = 1/2 VDD
VCO supply current (inhibit)
See Note 4
Low level output voltage
Input current at Select, VCO inhibit
IOH = –2 mA
IOL = 2 mA
MIN
TYP
MAX
2.4
V
0.3
0.9
UNIT
1.5
2.1
V
±1
µA
10
0.35
V
MΩ
1
µA
IDD(VCO) VCO supply current
See Note 5
8.4
17
mA
NOTES: 4. Current into VCO VDD, when VCO INHIBIT = high, PFD is inhibited.
5. Current into VCO VDD, when VCO IN = 1/2 VDD, RBIAS = 3.3 kΩ, VCOOUT = 15−pF Load, VCO INHIBIT = GND, and PFD INHIBIT
= GND.
TI.COM
5
SLES150 − OCTOBER 2005
electrical characteristics, VDD = 3 V, TA = 25°C (unless otherwise noted) (continued)
PFD section
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
VOH
VOL
High level output voltage
Low level output voltage
IOH = –2 mA
IOL = 2 mA
2.4
IOZ
VIH
High impedance state output current
PFD inhibit = high, VO = VDD or GND
VIL
VTH
Low level input voltage at Fin−A, Fin−B
CIN
Input capacitance at Fin−A, Fin−B
5.6
pF
ZIN
IDD(Z)
Input impedance at Fin−A, Fin−B
10
MΩ
High level input voltage at Fin−A, Fin−B
V
±1
µA
2.1
V
0.5
Input threshold voltage at PFD inhibit
High impedance state PFD supply current
V
0.3
0.9
1.5
V
2.1
See Note 6
µA
1
IDD(PFD) PFD supply current
See Note 7
3
mA
NOTES: 6. The current into LOGIC VDD when FIN−A and FIN−B = ground, PFD INHIBIT = VDD, PFD OUT open, and VCO OUT is inhibited.
7. The current into LOGIC VDD when FIN−A = 1 MHz and FIN−B = 1 MHz (VI(PP) = 3 V, rectangular wave), PFD INHIBIT = GND, PFD
OUT open, and VCO OUT is inhibited.
operation characteristics, VDD = 3 V, TA = 25°C (unless otherwise noted)
VCO section
Parameter
TEST CONDITIONS
RBIAS = 3.3 kΩ, VCO IN = 1/2 VDD
MIN
TYP
MAX
UNIT
17
25
33
MHz
10
µs
9
14
ns
7.6
12
ns
fOSC
fSTB
Operation oscillation frequency
tr
tf
Rise time
CL = 15 pF
Fall time
CL = 15 pF
50%
55%
Time to stable oscillation (see Note 8)
Duty cycle at VCO OUT
RBIAS = 3.3 kΩ, VCO IN = 1/2 VDD
α (fOSC)
Temperature coefficient of oscillation
frequency
VCO IN = 1/2 VDD, TA = –20°C to
75°C
kSVS
(fosc)
Supply voltage coefficient of oscillation
frequency
VCO IN = 1/2 VDD, VDD = 4.75 V to
5.25 V
45%
–0.264
%/°C
0.004
%/mV
Jitter absolute (see Note 9)
PLL jitter, N = 128
325
ps
NOTES: 8. The time period to the stable VCO oscillation frequency after the VCO INHIBIT terminal is changed to a low level.
9. Jitter performance is highly dependent on circuit layout and external device characteristics. The jitter specification was made with
a carefully deigned PCB with no device socket.
PFD section
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
17
UNIT
fmax
tPLZ
Maximum operation frequency
PFD output disable time from low level
22
50
ns
tPHZ
tPZL
PFD output disable time from high level
21
50
ns
PFD output enable time to low level
6.5
30
ns
tPZH
tr
PFD output enable time to high level
7
30
ns
Rise time
CL = 15 pF
3.4
10
ns
tf
Fall time
CL = 15 pF
1.9
10
ns
6
TI.COM
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
MH
SLES150 − OCTOBER 2005
electrical characteristics, VDD = 3.3 V, TA = 25°C (unless otherwise noted)
VCO section
PARAMETER
TEST CONDITIONS
VOH
VOL
High level output voltage
VTH
II
Input threshold voltage at select, VCO inhibit
ZI(VCOIN)
IDD(INH)
VCO IN input impedance
VI = VDD or GND
VCO IN = 1/2 VDD
VCO supply current (inhibit)
See Note 10
Low level output voltage
Input current at Select, VCO inhibit
IOH = –2 mA
IOL = 2 mA
MIN
TYP
MAX
UNIT
2.64
V
0.33
1.05
1.65
V
2.25
V
±1
µA
10
MΩ
0.38
µA
1
IDD(VCO) VCO supply current
See Note 11
10.8
22
mA
NOTES: 10. Current into VCO VDD, when VCO INHIBIT = high, PFD is inhibited.
11. Current into VCO VDD, when VCO IN = 1/2 VDD, RBIAS = 3.3 kΩ, VCOOUT = 15−pF Load, VCO INHIBIT = GND, and PFD INHIBIT
= GND.
PFD section
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
2.97
UNIT
VOH
VOL
High level output voltage
Low level output voltage
IOH = –2 mA
IOL = 2 mA
IOZ
VIH
High impedance state output current
PFD inhibit = high, VO = VDD or GND
VIL
VTH
Low level input voltage at Fin−A, Fin−B
CIN
Input capacitance at Fin−A, Fin−B
5.6
pF
ZIN
IDD(Z)
Input impedance at Fin−A, Fin−B
10
MΩ
High level input voltage at Fin−A, Fin−B
V
±1
µA
2.1
V
0.5
Input threshold voltage at PFD inhibit
High impedance state PFD supply current
V
0.2
1.05
1.65
See Note 12
V
2.25
1
µA
IDD(PFD) PFD supply current
See Note 13
3
mA
NOTES: 12. The current into LOGIC VDD when FIN−A and FIN−B = ground, PFD INHIBIT = VDD, PFD OUT open, and VCO OUT is inhibited.
13. The current into LOGIC VDD when FIN−A = 1 MHz and FIN−B = 1 MHz (VI(PP) = 3.3 V, rectangular wave), PFD INHIBIT = GND,
PFD OUT open, and VCO OUT is inhibited.
operation characteristics, VDD = 3.3 V, TA = 25°C (unless otherwise noted)
VCO section
PARAMETER
TEST CONDITIONS
RBIAS = 3.3 kΩ, VCO IN = 1/2 VDD
MIN
TYP
MAX
UNIT
18
30
43
MHz
10
µs
14
ns
7.3
12
ns
50
55
fOSC
fstb
Operation oscillation frequency
tr
Rise time
CL = 15 pF
8.5
tf
fDUTY
Fall time
CL = 15 pF
Duty cycle at VCO OUT
RBIAS=3.3 kΩ, VCO IN = 1/2 VDD
α (fOSC)
Temperature coefficient of oscillation
frequency
VCO IN = 1/2 VDD, TA = –20°C to 75°C
–0.28
7
%/°C
kSVS(fOSC)
Supply voltage coefficient of oscillation
frequency
VCO IN = 1/2 VDD, VDD = 4.75 V to 5.25 V
0.004
%/m
V
Time to stable oscillation (see Note 14)
45
%
Jitter absolute (see Note 15)
PLL jitter, N = 128
245
ps
NOTES: 14. The time period to the stable VCO oscillation frequency after the VCO INHIBIT terminal is changed to a low level.
15. Jitter performance is highly dependent on circuit layout and external device characteristics. The jitter specification was made with
a carefully deigned PCB with no device socket.
TI.COM
7
SLES150 − OCTOBER 2005
operation characteristics, VDD = 3.3 V, TA = 25°C (unless otherwise noted) (continued)
PFD section
PARAMETER
TEST CONDITIONS
TYP
MAX
21
50
ns
PFD output disable time from high level
21
50
ns
PFD output enable time to low level
5.8
30
ns
6.2
30
ns
3
10
ns
1.7
10
ns
TYP
MAX
fmax
tPLZ
Maximum operation frequency
tPHZ
tPZL
tPZH
tr
PFD output enable time to high level
Rise time
CL = 15 pF
tf
Fall time
CL = 15 pF
MIN
22
PFD output disable time from low level
UNIT
MHz
electrical characteristics, VDD = 5 V, TA = 25°C (unless otherwise noted)
VCO section
PARAMETER
TEST CONDITIONS
VOH
VOL
High level output voltage
IOH = –2 mA
IOL = 2 mA
VTH
Input threshold voltage at select, VCO
inhibit
II
ZI(VCOIN)
Input current at Select, VCO inhibit
VCO IN input impedance
VI = VDD or GND
VCO IN = 1/2 VDD
IDD(inh)
VCO supply current (inhibit)
See Note 16
Low level output voltage
MIN
4
1.5
UNIT
V
2.5
0.5
V
3.5
V
±1
µA
1
µA
10
0.56
M(
IDD(vco)
VCO supply current
See Note 17
28
50
mA
NOTES: 16. Current into VCO VDD, when VCO INHIBIT = high, PFD is inhibited.
17. Current into VCO VDD, when VCO IN = 1/2 VDD, RBIAS = 3.3 kΩ, VCOOUT = 15−pF Load, VCO INHIBIT = GND, and PFD INHIBIT
= GND.
PFD section
PARAMETER
TEST CONDITIONS
VOH
VOL
High level output voltage
IOH = –2 mA
IOL = 2 mA
IOZ
High impedance state output current
VIH
VIL
High level input voltage at Fin−A, Fin−B
VTH
CIN
Input threshold voltage at PFD inhibit
Input capacitance at Fin−A, Fin−B
5.6
pF
ZIN
IDD(Z)
Input impedance at Fin−A, Fin−B
10
MΩ
Low level output voltage
MIN
TYP
PFD inhibit = high, Vo = VDD or
GND
0.2
V
±1
µA
4.5
V
1
1.5
See Note 18
UNIT
V
Low level input voltage at Fin−A, Fin−B
High impedance state PFD supply current
MAX
4.5
2.5
V
3.5
1
µA
IDD(PFD) PFD supply current
See Note 19
0.5
3
mA
NOTES: 18. The current into LOGIC VDD when FIN−A and FIN−B = ground, PFD INHIBIT = VDD, PFD OUT open, and VCO OUT is inhibited.
19. The current into LOGIC VDD when FIN−A = 1 MHz and FIN−B = 1 MHz (VI(PP) = 5 V, rectangular wave), PFD INHIBIT = GND, PFD
OUT open, and VCO OUT is inhibited
8
TI.COM
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SLES150 − OCTOBER 2005
operation characteristics, VDD = 5 V, TA = 25°C (unless otherwise noted)
VCO section
PARAMETER
TEST CONDITIONS
RBIAS = 3.3 kΩ, VCO IN = 1/2 VDD
MIN
TYP
MAX
UNIT
37
57
75
MHz
10
us
10
ns
6.4
10
ns
50%
55%
fOSC
fSTB
Operation oscillation frequency
tr
tf
Rise time
CL = 15 pF
Fall time
CL = 15 pF
fDUTY
α (fOSC)
Duty cycle at VCO OUT
RBIAS = 3.3 kΩ, VCO IN = 1/2 VDD
Temperature coefficient of oscillation
frequency
VCO IN = 1/2 VDD, TA = –20°C to
75°C
–0.346
%/°C
kSVS(fOS
C)
Supply voltage coefficient of oscillation
frequency
VCO IN = 1/2 VDD, VDD = 4.75 V
to 5.25 V
0.002
%/mV
Time to stable oscillation (see Note 20)
7.5
45%
Jitter absolute (see Note 21)
PLL jitter, N = 128
145
ps
NOTES: 20. The time period to the stable VCO oscillation frequency after the VCO INHIBIT terminal is changed to a low level.
21. Jitter performance is highly dependent on circuit layout and external device characteristics. The jitter specification was made with
a carefully deigned PCB with no device socket.
PFD section
PARAMETER
TYP
MAX
PFD output disable time from low level
20
40
ns
tPHZ
tPZL
PFD output disable time from high level
20
40
ns
4
20
ns
tPZH
tr
PFD output enable time to high level
4.3
20
ns
Rise time
CL = 15 pF
2.1
10
ns
tf
Fall time
CL = 15 pF
1.3
10
ns
fmax
tPLZ
Maximum operation frequency
TEST CONDITIONS
MIN
38
PFD output enable time to low level
TI.COM
UNIT
MHz
9
SLES150 − OCTOBER 2005
PARAMETER MEASUREMENT INFORMATION
90%
VCO OUT
90%
10%
10%
tr
tf
Figure 3. VCO Output Voltage Waveform
FIN−A
VDD
50%
GND
FIN−B
VDD
50%
GND
VDD
PFD INHIBIT
50%
50%
GND
VDD
90%
PFD OUT
90%
50%
GND
50%
50%
50%
10%
10%
tPZH
tPHZ
tPZL
tr
tPLZ
tf
Figure 4. PFD Output Voltage Waveform
Table 4. PFD Output Test Conditions
PARAMETER
RL
CL
1 kΩ
15 pF
tPZH
tPHZ
tr
tPZL
tPLZ
S1
S2
OPEN
CLOSE
CLOSE
OPEN
tf
10
TI.COM
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SLES150 − OCTOBER 2005
PARAMETER MEASUREMENT INFORMATION
Measurement
Point
S1
DUT
RL
CL
S2
Figure 5. PFD Output Test Conditions
TYPICAL CHARACTERISTICS
VCO OSCILATION FREQUENCY
VS
VCO CONTROL VOLTAGE
Vdd=3.0V Rbias=3.3kohm
VCO OSCILATION FREQUENCY
VS
VCO CONTROL VOLTAGE
Vdd=3.0V Rbias=2.2kohm
100
100
90
90
80
fosc − VCO Oscilation Frequency NHz
fosc − VCO Oscilation Frequency NHz
−25°C
25°C
70
85°C
60
50
40
30
20
80
−25°C
70
25°C
60
85°C
50
40
30
20
10
10
0
0
0
1
2
3
0
4
1
2
3
4
VCOIN − VCO Control Voltage − V
VCOIN − VCO Control Voltage − V
Figure 7.
Figure 6.
TI.COM
11
SLES150 − OCTOBER 2005
TYPICAL CHARACTERISTICS
VCO OSCILATION FREQUENCY
VS
VCO CONTROL VOLTAGE
Vdd=3.3V Rbias=2.2kohm
VCO OSCILATION FREQUENCY
VS
VCO CONTROL VOLTAGE
Vdd=3.0V Rbias=5.1kohm
100
100
90
90
80
80
fosc − VCO Oscilation Frequency NHz
fosc − VCO Oscilation Frequency NHz
−25°C
70
−25°C
25°C
60
85°C
50
40
30
20
25°C
70
85°C
60
50
40
30
20
10
10
0
0
0
1
2
3
0
4
1
3
4
Figure 9.
Figure 8.
VCO OSCILATION FREQUENCY
VS
VCO CONTROL VOLTAGE
Vdd=3.3V Rbias=5.1kohm
VCO OSCILATION FREQUENCY
VS
VCO CONTROL VOLTAGE
Vdd=3.3V Rbias=3.3kohm
100
100
90
90
−25°C
80
fosc − VCO Oscilation Frequency NHz
fosc − VCO Oscilation Frequency NHz
2
VCOIN − VCO Control Voltage − V
VCOIN − VCO Control Voltage − V
25°C
70
85°C
60
50
40
30
20
80
−25°C
70
25°C
60
85°C
50
40
30
20
10
10
0
0
0
1
2
3
0
4
1
2
VCOIN − VCO Control Voltage − V
VCOIN − VCO Control Voltage − V
Figure 11.
Figure 10.
12
TI.COM
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
3
4
SLES150 − OCTOBER 2005
TYPICAL CHARACTERISTICS
VCO OSCILATION FREQUENCY
VCO OSCILATION FREQUENCY
VS
VS
VCO CONTROL VOLTAGE
Vdd=5.0V Rbias=3.3kohm
VCO CONTROL VOLTAGE
Vdd=5.0V Rbias=2.2kohm
140
140
−25°C
120
120
fosc − VCO Oscilation Frequency NHz
fosc − VCO Oscilation Frequency NHz
25°C
100
85°C
80
60
40
20
−25°C
100
25°C
85°C
80
60
40
20
0
0
0
1
2
3
4
5
0
6
1
2
3
4
5
6
5
6
VCOIN − VCO Control Voltage − V
VCOIN − VCO Control Voltage − V
Figure 13.
Figure 12.
VCO Oscilation frequency
VCO OSCILATION FREQUENCY
VS
VCO CONTROL VOLTAGE
Vs
Vdd=5.0V Rbias=5.1kohm
Bias resister
Vdd=3V, VCOIN=1.5V, Ta=25’C
140
35
VCO Oscilationfrequency MHz
fosc − VCO Oscilation Frequency NHz
120
100
−25°C
80
25°C
85°C
60
40
20
0
0
1
2
3
4
5
33
31
29
27
25
23
21
19
17
15
1
6
VCOIN − VCO Control Voltage − V
2
3
4
Rbias(kohm)
Figure 15.
Figure 14.
TI.COM
13
SLES150 − OCTOBER 2005
TYPICAL CHARACTERISTICS
VCO Oscilation frequency
VCO Oscilation frequency
Vs
Bias resister
Bias resister
Vs
Vdd=5V, VCOIN=2.5V, Ta=25’C
Vdd=3.3V, VCOIN=1.6V, Ta=25’C
65
VCO Oscilationfrequency MHz
VCO Oscilationfrequency MHz
40
38
36
34
32
30
28
26
24
22
20
1
2
3
4
5
63
61
59
57
55
53
51
49
47
45
1
6
2
3
5
6
Rbias(kohm)
Rbias(kohm)
Figure 17.
Figure 16.
Temperature Coefficient Oscilation frequency
Temperature Coefficient Oscilation frequency
Vs
Vs
Bias resister
Bias resister
Vdd=3.3V, VCOIN=1.6V, Ta=−20’C to 75’C
Vdd=3V, VCOIN=1.5V, Ta=−20’C to 75’C
0.000
0.000
−0.050
−0.050
−0.100
−0.100
Temperature Coefficient of Oscilation frequency %/’C
Temperature Coefficient of Oscilationfrequency %/’C
4
−0.150
−0.200
−0.250
−0.300
−0.350
−0.400
−0.450
−0.150
−0.200
−0.250
−0.300
−0.350
−0.400
−0.450
−0.500
−0.500
1
2
3
4
5
1
6
2
3
4
Rbias(kohm)
Rbias(kohm)
Figure 19.
Figure 18.
14
TI.COM
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
5
6
SLES150 − OCTOBER 2005
TYPICAL CHARACTERISTICS
VCO Oscilation frequency
Temperature Coefficient Oscilation frequency
Vs
Vs
VCO Supply Voltage
Bias resister
VCOIN=1.5V, Ta=25’C
0.000
35
−0.050
33
−0.100
31
−0.150
29
VCO Oscilation frequency MHz
Temperature Coefficient of Oscilation frequency %/’C
Vdd=5.0V, VCOIN=2.5V, Ta=−20’C to 75’C
−0.200
−0.250
−0.300
−0.350
27
25
23
21
−0.400
19
−0.450
17
15
−0.500
1
2
3
4
5
2.5
6
2.7
2.9
3.3
3.5
Figure 21.
Figure 20.
VCO Oscilation frequency
VCO Oscilation frequency
Vs
Vs
VCO Supply Voltage
VCO Supply Voltage
VCOIN=2.5V, Ta=25’C
VCOIN=1.6V, Ta=25’C
40
65
38
63
36
61
34
59
VCO Oscilation frequency MHz
VCO Oscilation frequency MHz
3.1
VCO Supply Voltage (V)
Rbias(kohm)
32
30
28
26
57
55
53
51
24
49
22
47
45
20
2.8
3
3.2
3.4
3.6
4
3.8
4.5
5
5.5
6
VCO Supply Voltage (V)
VCO Supply Voltage (V)
Figure 23.
Figure 22.
TI.COM
15
SLES150 − OCTOBER 2005
TYPICAL CHARACTERISTICS
Supply Voltage Coefficient of Oscilation frequency
Supply Voltage Coefficient of Oscilation frequency
Vs
Vs
Bias resister
Bias resister
Vdd=3.0V to 3.6V,VCOIN=1.6V, Ta=25’C
0.100
0.100
0.080
0.080
0.060
0.060
Supply Voltage Coefficient of Oscilation frequency %/mV
Supply Voltage Coefficient of Oscilation frequency %/mV
Vdd=2.7V to 3.3V,VCOIN=1.5V, Ta=25’C
0.040
0.020
0.000
−0.020
−0.040
−0.060
−0.080
0.040
0.020
0.000
−0.020
−0.040
−0.060
−0.080
−0.100
−0.100
1
2
3
4
5
1
6
2
3
5
6
5
6
Figure 25.
Figure 24.
Recommended Lock frequency
Supply Voltage Coefficient of Oscilation frequency
Vs
Vs
Bias resister
Bias resister
Vdd=2.85V to 3.15V, Ta=−20’C to 75’C
Vdd=4.5V to 5.5V,VCOIN=2.5V, Ta=25’C
0.100
50
0.080
45
0.060
40
RECOMMENDED LOCK FREQUENCY MHz
Supply Voltage Coefficient of Oscilation frequency %/mV
4
Rbias (kohm)
Rbias (kohm)
0.040
0.020
0.000
−0.020
−0.040
−0.060
35
30
25
20
15
10
5
−0.080
0
−0.100
1
2
3
4
5
1
6
2
3
4
Rbias (kohm)
Rbias (kohm)
Figure 27.
Figure 26.
16
TI.COM
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SLES150 − OCTOBER 2005
TYPICAL CHARACTERISTICS
Recommended Lock frequency
Recommended Lock frequency
Vs
Vs
Bias resister
Bias resister
Vdd=4.75V to 5.25V, Ta=−20’C to 75’C
Vdd=3.135V to 3.465V, Ta=−20’C to 75’C
80
50
45
70
RECOMMENDED LOCK FREQUENCY MHz
RECOMMENDED LOCK FREQUENCY MHz
40
35
30
25
20
15
10
60
50
40
30
20
10
5
0
0
1
2
3
4
5
1
6
2
3
4
5
6
Rbias (kohm)
Rbias (kohm)
Figure 29.
Figure 28.
TI.COM
17
PACKAGE OPTION ADDENDUM
www.ti.com
30-Jul-2011
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package
Drawing
Pins
Package Qty
Eco Plan
(2)
Lead/
Ball Finish
MSL Peak Temp
TLC2932AIPW
ACTIVE
TSSOP
PW
14
90
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TLC2932AIPWG4
ACTIVE
TSSOP
PW
14
90
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TLC2932AIPWR
ACTIVE
TSSOP
PW
14
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TLC2932AIPWRG4
ACTIVE
TSSOP
PW
14
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
(3)
Samples
(Requires Login)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
TLC2932AIPWR
Package Package Pins
Type Drawing
TSSOP
PW
14
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
2000
330.0
12.4
Pack Materials-Page 1
6.9
B0
(mm)
K0
(mm)
P1
(mm)
5.6
1.6
8.0
W
Pin1
(mm) Quadrant
12.0
Q1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
TLC2932AIPWR
TSSOP
PW
14
2000
367.0
367.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All
semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time
of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Mobile Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated