MAXIM MAX8744ETJ+

19-3796; Rev 0; 4/06
KIT
ATION
EVALU
E
L
B
A
AVAIL
High-Efficiency, Quad Output, Main PowerSupply Controllers for Notebook Computers
♦
♦
♦
♦
♦
♦
♦
♦
♦
♦
♦
♦
♦
♦
Fixed-Frequency, Current-Mode Control
40/60 Optimal Interleaving
Internal BST Switches
Internal 5V, 100mA Linear Regulator
Auxiliary Linear-Regulator Driver (12V or
Adjustable Down to 1V)
Dual Mode™ Feedback—3.3V/5V Fixed or
Adjustable Output Voltages
200kHz/300kHz/500kHz Switching Frequency
Undervoltage and Thermal-Fault Protection
Overvoltage-Fault Protection (MAX8744 Only)
6V to 26V Input Range
2V ±0.75% Reference Output
Independent Enable Inputs and Power-Good
Outputs
Soft-Start and Soft-Shutdown (Voltage Ramp)
8µA (typ) Shutdown Current
Ordering Information
TEMP RANGE
PINPACKAGE
MAX8744ETJ+
-40°C to +85°C
32 Thin QFN
T3255-4
(5mm x 5mm)
MAX8745ETJ+
-40°C to +85°C
32 Thin QFN
T3255-4
(5mm x 5mm)
PART
PKG
CODE
+Denotes lead-free package.
IN
LDO5
PGND
DL5
LX5
24
DL3
TOP VIEW
PGOODA
Pin Configuration
LX3
The MAX8744/MAX8745 are dual step-down, switchmode, power-supply (SMPS) controllers with synchronous rectification, intended for main 5V/3.3V power
generation in battery-powered systems. Fixed-frequency operation with optimal interleaving minimizes input
ripple current from the lowest input voltages up to the
26V maximum input. Optimal 40/60 interleaving allows
the input voltage to go down to 8.3V before duty-cycle
overlap occurs, compared to 180° out-of-phase regulators where the duty-cycle overlap occurs when the
input drops below 10V.
Output current sensing provides peak current-limit protection, using either an accurate sense resistor or using
lossless inductor DCR current sensing. A low-noise
mode maintains high light-load efficiency while keeping
the switching frequency out of the audible range.
An internal, fixed 5V, 100mA linear regulator powers up
the MAX8744/MAX8745 and their gate drivers, as well
as external keep-alive loads. When the main PWM regulator is in regulation, an automatic bootstrap switch
bypasses the internal linear regulator, providing current
up to 200mA. An additional adjustable linear-regulator
driver with an external pnp transistor may be used with
a secondary winding to provide a 12V supply, or powered directly from the main outputs to generate lowvoltage outputs as low as 1V.
Independent enable controls and power-good signals
allow flexible power sequencing. Voltage soft-start
gradually ramps up the output voltage and reduces
inrush current, while soft-shutdown gradually ramps the
output voltage down, preventing negative voltage dips.
The MAX8744/MAX8745 feature output undervoltage
and thermal-fault protection. The MAX8744 also
includes output overvoltage-fault protection.
Features
23
22
21
20
19
18
17
The MAX8744/MAX8745 are available in a 32-pin, 5mm
x 5mm, thin QFN package. The exposed backside pad
improves thermal characteristics for demanding linear
keep-alive applications.
DH3 25
16
DH5
BST3 26
15
BST5
Applications
PGOOD3 27
14
PGOOD5
CSL3 28
13
CSL5
12
CSH5
Dual Mode is a trademark of Maxim Integrated Products, Inc.
11
FB5
FBA 31
10
SKIP
9
FSEL
+
1
2
3
4
5
6
7
8
ON3
ON5
REF
GND
OUTA 32
SHDN
PDAs and Mobile Communicators
FB3 30
ILIM
Notebook and Subnotebook Computers
CSH3 29
ONA
2 to 4 Li+ Cell Battery-Powered Devices
MAX8744
MAX8745
DRVA
Main Power Supplies
THIN QFN
5mm x 5mm
________________________________________________________________ Maxim Integrated Products
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
1
MAX8744/MAX8745
General Description
MAX8744/MAX8745
High-Efficiency, Quad Output, Main PowerSupply Controllers for Notebook Computers
ABSOLUTE MAXIMUM RATINGS
IN, SHDN, DRVA, OUTA to GND............................-0.3V to +28V
LDO5, ON3, ON5, ONA to GND ..............................-0.3V to +6V
PGOODA, PGOOD3, PGOOD5 to GND...................-0.3V to +6V
CSL3, CSH3, CSL5, CSH5 to GND ..........................-0.3V to +6V
REF, FB3, FB5, FBA to GND...................-0.3V to (VLDO5 + 0.3V)
SKIP, FSEL, ILIM to GND........................-0.3V to (VLDO5 + 0.3V)
DL3, DL5 to PGND..................................-0.3V to (VLDO5 + 0.3V)
BST3, BST5 to PGND .............................................-0.3V to +34V
BST3 to LX3..............................................................-0.3V to +6V
DH3 to LX3 ..............................................-0.3V to (VBST3 + 0.3V)
BST5 to LX5..............................................................-0.3V to +6V
DH5 to LX5 ..............................................-0.3V to (VBST5 + 0.3V)
GND to PGND .......................................................-0.3V to +0.3V
BST3, BST5 LDO5 .................................................-0.3V to +0.3V
LDO Short Circuit to GND ..........................................Momentary
REF Short Circuit to GND ...........................................Momentary
DRVA Current (Sinking) ......................................................30mA
OUTA Shunt Current ...........................................................30mA
Continuous Power Dissipation (TA = +70°C)
Multilayer PC Board
32-Pin, 5mm x 5mm TQFN
(derated 34.5mW/°C above +70°C) .........................2459mW
Operating Temperature Range ...........................-40°C to +85°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) ................................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(Circuit of Figure 1, VIN = 12V, both SMPS enabled, FSEL = REF, SKIP = GND, ILIM = LDO5, FBA = LDO5, IREF = ILDO5 = IOUTA =
no load, TA = 0°C to +85°C, unless otherwise noted. Typical values are at TA = +25°C.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
INPUT SUPPLIES (Note 1)
VIN Input Voltage Range
VIN
VIN Operating Supply Current
IIN
LDO5 in regulation
5.4
26.0
IN = LDO5, VCSL5 < 4.4V
4.5
5.5
V
LDO5 switched over to CSL5, either
SMPS on
20
36
µA
VIN Standby Supply Current
IIN(STBY)
VIN = 6V to 26V, both SMPS off, includes
ISHDN
65
120
µA
VIN Shutdown Supply Current
IIN(SHDN)
VIN = 6V to 26V
8
20
µA
3.5
4.5
mW
Quiescent Power Consumption
PQ
Both SMPS on, FB3 = FB5 = LDO5,
SKIP = GND, VCSL3 = 3.5V, VCSL5 = 5.3V,
VOUTA = 15V,
PIN + PCSL3 + PCSL5 + POUTA
MAIN SMPS CONTROLLERS
3.3V Output Voltage in Fixed
Mode
VOUT3
VIN = 6V to 26V, SKIP = FB3 = LDO5,
0 < VCSH3 - VCSL3 < 50mV (Note 2)
3.265
3.315
3.365
V
5V Output Voltage in Fixed Mode
VOUT5
VIN = 6V to 26V, SKIP = FB5 = LDO5,
0 < VCSH5 - VCSL5 < 50mV (Note 2)
4.94
5.015
5.09
V
VIN = 6V to 26V, FB3 or FB5
duty factor = 20% to 80%
1.980
2.010
2.040
VIN = 6V to 26V, FB3 or FB5
duty factor = 50%
1.990
2.010
2.030
Feedback Voltage in Adjustable
Mode (Note 2)
2
VFB_
V
_______________________________________________________________________________________
High-Efficiency, Quad Output, Main PowerSupply Controllers for Notebook Computers
(Circuit of Figure 1, VIN = 12V, both SMPS enabled, FSEL = REF, SKIP = GND, ILIM = LDO5, FBA = LDO5, IREF = ILDO5 = IOUTA =
no load, TA = 0°C to +85°C, unless otherwise noted. Typical values are at TA = +25°C.)
PARAMETER
SYMBOL
Output Voltage Adjust Range
CONDITIONS
Either SMPS
3.0
Feedback Input Leakage Current
VFB3 = VFB5 = 2.1V
DC Load Regulation
Either SMPS, SKIP = LDO5,
0 < VCSH_ - VCSL_ < 50mV
Line Regulation Error
Either SMPS, 6V < VIN < 26V
Maximum Duty Factor
DMAX
Minimum On-Time
tONMIN
SMPS3-to-SMPS5 Phase Shift
MAX
UNITS
5.5
V
VLOO5
- 1.0
VLOO5
- 0.4
V
+0.1
µA
-0.1
FSEL = GND
fOSC
TYP
2.0
FB3, FB5 Dual Mode Threshold
Operating Frequency (Note 1)
MIN
-0.1
%
0.03
170
200
%/V
230
FSEL = REF
270
300
330
FSEL = LDO5
425
500
575
(Note 1)
97.5
SMPS5 starts after SMPS3
kHz
99
%
100
ns
40
%
144
Deg
CURRENT LIMIT
ILIM Adjustment Range
Current-Sense Input Leakage
Current
Current-Limit Threshold (Fixed)
CSH3 = CSH5 = GND or LDO5
VLIMIT
Current-Limit Threshold
(Adjustable)
VLIMIT
Current-Limit Threshold
(Negative)
VNEG
Current-Limit Threshold
(Zero Crossing)
VZX
VCSH_ - VCSL _, ILIM = LDO5
VCSH_ - VCSL _
ILIM Leakage Current
V
-1
+1
µA
mV
45
50
55
185
200
215
VILIM = 1.00V
94
100
106
-67
-60
-53
VCSH_ - VCSL _, SKIP = ILIM = LDO5
VCSH_ - VCSL _, SKIP = LDO5, adjustable
mode, percent of current limit
VCSH_ - VCSL _, SKIP = GND,
ILIM = LDO5
VIDLE
VCSH_ - VCSL _,
SKIP = GND
VIDLE
VCSH_ - VCSL _,
SKIP = REF
ILIM = GND or REF
-120
mV
mV
%
0
3
6
mV
6
10
14
mV
With respect to
current-limit
threshold (VLIMIT)
ILIM = LDO5
Idle Mode Threshold
(Low Audible-Noise Mode)
VREF
VILIM = 2.00V
ILIM = LDO5
Idle Mode™ Threshold
0.5
20
2.5
With respect to
current-limit
threshold (VLIMIT)
5
%
7.5
10
-1
mV
%
+1
µA
Idle Mode is a trademark of Maxim Integrated Products, Inc.
_______________________________________________________________________________________
3
MAX8744/MAX8745
ELECTRICAL CHARACTERISTICS (continued)
MAX8744/MAX8745
High-Efficiency, Quad Output, Main PowerSupply Controllers for Notebook Computers
ELECTRICAL CHARACTERISTICS (continued)
(Circuit of Figure 1, VIN = 12V, both SMPS enabled, FSEL = REF, SKIP = GND, ILIM = LDO5, FBA = LDO5, IREF = ILDO5 = IOUTA =
no load, TA = 0°C to +85°C, unless otherwise noted. Typical values are at TA = +25°C.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
Soft-Start Ramp Time
tSSTART
Measured from the rising edge of ON_ to
full scale
2
ms
Soft-Stop Ramp Time
tSSTOP
Measured from the falling edge of ON_ to
full scale
4
ms
INTERNAL FIXED LINEAR REGULATORS
LDO5 Output Voltage
VLDO5
ON5 = GND, 6V < VIN < 26V,
0 < ILDO5 < 100mA
LDO5 Undervoltage-Lockout Fault
Threshold
Rising edge, hysteresis = 1% (typ)
LDO5 Bootstrap Switch Threshold
Rising edge of CSL5, hysteresis = 1% (typ)
LDO5 Bootstrap Switch Resistance
LDO5 to CSL5, VCSL5 = 5V, ILDO5 = 50mA
Short-Circuit Current
LDO5 = GND, ON5 = GND
Short-Circuit Current (Switched
over to CSL_)
LDO5 = GND, VCSL5 > 4.7V
4.85
4.35
200
4.95
5.10
V
225
450
mA
4.55
4.70
V
1
5
Ω
225
450
mA
425
mA
AUXILIARY LINEAR REGULATOR
DRVA Voltage Range
VDRVA
DRVA Drive Current
FBA Regulation Threshold
0.5
VFBA = 0.965V, VDRVA = 5V
VFBA
FBA Load Regulation
VDRVA = 5V, IDRVA = 1mA (sink)
0.4
10
0.98
VDRA = 5V, IDRVA = 0.5mA to 5mA
OUTA Shunt Trip Level
Rising edge
FBA Leakage Current
VFBA = 1.035V
Secondary Feedback Regulation
Threshold
VDRVA - VOUTA
25
IOUTA
VDRVA = VOUTA = 25V
VREF
LDO5 in regulation, IREF = 0
V
mA
1.00
1.02
V
-1.2
-2.2
%
26
-0.1
DL5 Pulse Width
OUTA Leakage Current
26.0
VFBA = 1.05V, VDRVA = 5V
27
V
+0.1
µA
0
V
1/
3fOSC
µs
50
µA
2.015
V
+10
mV
REFERENCE (REF)
Reference Voltage
Reference Load-Regulation Error
REF Lockout Voltage
ΔVREF
VREF(UVLO)
IREF = -5µA to +50µA
1.985
2.00
-10
Rising edge, hysteresis = 100mV (typ)
1.90
V
FAULT DETECTION
Output Overvoltage Trip
Threshold (MAX8744 Only)
Output Overvoltage Fault
Propagation Delay (MAX8744 Only)
4
With respect to error-comparator
threshold
tOVP
50mV overdrive
8
11
10
_______________________________________________________________________________________
14
%
µs
High-Efficiency, Quad Output, Main PowerSupply Controllers for Notebook Computers
(Circuit of Figure 1, VIN = 12V, both SMPS enabled, FSEL = REF, SKIP = GND, ILIM = LDO5, FBA = LDO5, IREF = ILDO5 = IOUTA =
no load, TA = 0°C to +85°C, unless otherwise noted. Typical values are at TA = +25°C.)
PARAMETER
SYMBOL
Output Undervoltage Protection
Trip Threshold
Output Undevoltage Fault
Propagation Delay
Output Undervoltage Protection
Blanking Time
With respect to error-comparator
threshold
tUVP
tBLANK
tPGOOD_
PGOOD_ Output Low Voltage
PGOOD_ Leakage Current
Thermal-Shutdown Threshold
MIN
TYP
MAX
UNITS
65
70
75
%
50mV overdrive
10
From rising edge of ON_ with respect to
fSW
With respect to error-comparator
threshold, hysteresis = 1% (typ)
PGOOD_ Lower Trip Threshold
PGOOD_ Propagation Delay
CONDITIONS
5000
6144
7000
1/fOSC
-12
-10
-8
%
Falling edge, 50mV overdrive
10
Rising edge, 50mV overdrive
1
ISINK = 1mA
IPGOOD_
tSHDN
µs
High state, PGOOD_ forced to 5.5V
Hysteresis = 15°C
µs
0.4
V
1
µA
+160
°C
GATE DRIVERS
DH_ Gate-Driver On-Resistance
RDH
DL_ Gate-Driver On-Resistance
RDL
DH_ Gate-Driver Source/Sink
Current
DL_ Gate-Driver Source Current
DL_ Gate-Driver Sink Current
1.3
1.7
5
DL_, low state
0.6
3
DH_ forced to 2.5V, BST_ – LX_ forced to
5V
IDL (SOURCE) DL_ forced to 2.5V
IDL (SINK)
DL_ forced to 2.5V
tDEAD
Internal BST_ Switch OnResistance
RBST
5
DL_, high state
IDH
Dead Time
BST_ Leakage Current
BST_ – LX_ forced to 5V
Ω
Ω
2
A
1.7
A
3.3
A
DH_low to DL_high
15
45
DL_low to DH_high
15
44
IBST = 10mA
5
VBST_ = 26V
2
ns
Ω
20
µA
INPUTS AND OUTPUTS
SHDN Input Trip Level
ONA Logic Input Voltage
Rising trip level
1.1
1.6
2.2
Falling trip level
0.96
1
1.04
Hysteresis = 600mV (typ)
High
2.4
Low
0.8
SMPS off level/clear fault level
ON3, ON5 Input Voltage
V
V
0.8
Delay start level
1.9
SMPS on level
2.4
2.1
V
_______________________________________________________________________________________
5
MAX8744/MAX8745
ELECTRICAL CHARACTERISTICS (continued)
MAX8744/MAX8745
High-Efficiency, Quad Output, Main PowerSupply Controllers for Notebook Computers
ELECTRICAL CHARACTERISTICS (continued)
(Circuit of Figure 1, VIN = 12V, both SMPS enabled, FSEL = REF, SKIP = GND, ILIM = LDO5, FBA = LDO5, IREF = ILDO5 = IOUTA =
no load, TA = 0°C to +85°C, unless otherwise noted. Typical values are at TA = +25°C.)
PARAMETER
SYMBOL
CONDITIONS
SKIP, FSEL
Tri-Level Input Logic
MIN
High
VLDO5
- 0.4
REF
1.65
TYP
GND
Input Leakage Current
MAX
2.35
UNITS
V
0.5
SKIP, FSEL forced to GND or LDO5
-1
+1
SHDN forced to GND or 26V
-1
+1
µA
ELECTRICAL CHARACTERISTICS
(Circuit of Figure 1, VIN = 12V, both SMPS enabled, FSEL = REF, SKIP = GND, ILIM = LDO5, FBA = LDO5, IREF = ILDO5 = IOUTA =
no load, TA = -40°C to +85°C, unless otherwise noted.) (Note 3)
PARAMETER
SYMBOL
CONDITIONS
MIN
MAX
LDO5 in regulation
5.4
26.0
IN = LDO5, VCSL5 < 4.4V
4.5
5.5
UNITS
INPUT SUPPLIES (Note 1)
VIN Input Voltage Range
VIN
VIN Operating Supply Current
IIN
LDO5 switched over to CSL5, either SMPS on
40
µA
VIN = 6V to 26V, both SMPS off, includes
ISHDN
120
µA
20
µA
4.5
mW
VIN Standby Supply Current
IIN(STBY)
VIN Shutdown Supply Current
IIN(SHDN) VIN = 6V to 26V
Quiescent Power Consumption
PQ
V
Both SMPS on, FB3 = FB5 = LDO5; SKP =
GND, VCSL3 = 3.5V, VCSL5 = 5.3V,
VOUTA = 15V,
PIN + PCSL3 + PCSL5
MAIN SMPS CONTROLLERS
3.3V Output Voltage in Fixed
Mode
VOUT3
VIN = 6V to 26V, SKIP = FB3 = LDO5,
0 < VCSH3 - VCSL3 < 50mV (Note 2)
3.255
3.375
V
5V Output Voltage in Fixed Mode
VOU5
VIN = 6V to 26V, SKIP = FB5 = LDO5,
0 < VCSH5 - VCSL5 < 50mV (Note 2)
4.925
5.105
V
Feedback Voltage in Adjustable
Mode
VFB_
VIN = 6V to 26V, FB3 or FB5
duty factor = 20% to 80% (Note 2)
1.974
2.046
V
2.0
5.5
V
3V
VLDO5
- 0.4
V
170
230
Output Voltage Adjust Range
Either SMPS
FB3, FB5 Dual Mode Threshold
FSEL = GND
Operating Frequency (Note 1)
Maximum Duty Factor
6
fOSC
DMAX
FSEL = REF
270
330
FSEL = LDO5
425
575
97
_______________________________________________________________________________________
kHz
%
High-Efficiency, Quad Output, Main PowerSupply Controllers for Notebook Computers
(Circuit of Figure 1, VIN = 12V, both SMPS enabled, FSEL = REF, SKIP = GND, ILIM = LDO5, FBA = LDO5, IREF = ILDO5 = IOUTA =
no load, TA = -40°C to +85°C, unless otherwise noted.) (Note 3)
PARAMETER
SYMBOL
CONDITIONS
MIN
MAX
UNITS
0.5
VREF
V
44
56
mV
CURRENT LIMIT
ILIM Adjustment Range
Current-Limit Threshold (Fixed)
VLIMIT
VCSH_ - VCSL _, ILIM = LDO5
Current-Limit Threshold
(Adjustable)
VLIMIT
VCSH_ - VCSL _
VILIM = 2.00V
185
215
VILIM = 1.00V
93
107
ON5 = GND, 6V < VIN < 26V,
0 < ILDO5 < 100mA
4.85
5.10
V
Rising edge, hysteresis = 1% (typ)
3.7
4.1
V
LDO5 Bootstrap Switch Threshold
Rising edge of CSL5, hysteresis = 1% (typ)
4.30
4.75
V
Short-Circuit Current
LDO5 = GND, ON5 = GND
450
mA
Short-Circuit Current (Switched
over to CSL_)
LDO5 = GND, VCSL5 > 4.7V
mV
INTERNAL FIXED LINEAR REGULATORS
LDO5 Output Voltage
VLDO5
LDO5 Undervoltage-Lockout Fault
Threshold
200
mA
AUXILIARY LINEAR REGULATOR
DRVA Voltage Range
VDRVA
0.5
VFBA = 1.05V, VDRVA = 5V
DRVA Drive Current
VFBA = 0.965V, VDRVA = 5V
FBA Regulation Threshold
VFBA
VDRVA = 5V, IDRVA = 1mA (sink)
OUTA Shunt Trip Level
26
0.4
10
V
mA
0.98
1.02
V
25
27
V
1.980
2.020
V
REFERENCE (REF)
Reference Voltage
VREF
LDO5 in regulation, IREF = 0
_______________________________________________________________________________________
7
MAX8744/MAX8745
ELECTRICAL CHARACTERISTICS (continued)
MAX8744/MAX8745
High-Efficiency, Quad Output, Main PowerSupply Controllers for Notebook Computers
ELECTRICAL CHARACTERISTICS (continued)
(Circuit of Figure 1, VIN = 12V, both SMPS enabled, FSEL = REF, SKIP = GND, ILIM = LDO5, FBA = LDO5, IREF = ILDO5 = IOUTA =
no load, TA = -40°C to +85°C, unless otherwise noted.) (Note 3)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
FAULT DETECTION
Output Overvoltage Trip
Threshold (MAX8744 Only)
With respect to error comparator threshold
8
14
%
Output Undervoltage Protection
With respect to error comparator threshold
65
75
%
PGOOD_ Lower Trip Threshold
With respect to error comparator threshold,
hysteresis = 1%
-12
-8
%
PGOOD_ Output Low Voltage
ISINK = 1mA
0.4
V
BST_ – LX_ forced to 5V
5
Ω
DL_, high state
5
DL_, low state
3
GATE DRIVERS
DH_ Gate-Driver On-Resistance
DL_ Gate-Driver On-Resistance
RDH
RDL
Ω
INPUTS AND OUTPUTS
SHDN Input Trip Level
ONA Logic Input Voltage
Rising trip level
1.0
2.3
Falling trip level
0.96
1.04
Hysteresis = 600mV
High
2.4
Low
0.8
SMPS off level/clear fault level
ON3, ON5 Input Voltage
Tri-Level Input Logic
V
0.8
Delay start level
1.9
SMPS on level
2.4
SKIP, FSEL
V
High
VLDO5 - 0.4
REF
1.65
GND
2.1
V
2.35
V
0.5
Note 1: The MAX8744/MAX8745 cannot operate over all combinations of frequency, input voltage (VIN), and output voltage. For
large input-to-output differentials and high switching-frequency settings, the required on-time may be too short to maintain
the regulation specifications. Under these conditions, a lower operating frequency must be selected. The minimum on-time
must be greater than 150ns, regardless of the selected switching frequency. On-time and off-time specifications are measured from 50% point to 50% point at the DH_ pin with LX_ = GND, VBST_ = 5V, and a 250pF capacitor connected from
DH_ to LX_. Actual in-circuit times may differ due to MOSFET switching speeds.
Note 2: When the inductor is in continuous conduction, the output voltage has a DC-regulation level lower than the error-comparator
threshold by 50% of the ripple. In discontinuous conduction (SKIP = GND, light load), the output voltage has a DC regulation level higher than the trip level by approximately 1% due to slope compensation.
Note 3: Specifications from -40°C to +85°C are guaranteed by design, not production tested.
8
_______________________________________________________________________________________
High-Efficiency, Quad Output, Main PowerSupply Controllers for Notebook Computers
5V OUTPUT EFFICIENCY
vs. LOAD CURRENT
90
70
20V
60
80
70
LOW-NOISE
MODE
60
SKIP MODE
PWM MODE
0.1
1
LOAD CURRENT (A)
50
10
3.3V OUTPUT EFFICIENCY
vs. LOAD CURRENT
70
1.0
70
LOW-NOISE
MODE
0.1
1
LOAD CURRENT (A)
SKIP MODE
3.36
PWM MODE
0.01
0.1
1
LOAD CURRENT (A)
PWM MODE
SUPPLY CURRENT (mA)
5.0V OUTPUT
-1
3.30
PWM MODE
10
100
MAX8744 toc07
0
LOW-NOISE MODE
3.33
3.27
0
NO-LOAD INPUT SUPPLY CURRENT
vs. INPUT VOLTAGE
1
5.0
3.24
0.001
OUTPUT VOLTAGE DEVIATION
vs. INPUT VOLTAGE
3.3V OUTPUT
4.0
3.39
50
10
2.0
3.0
LOAD CURRENT (A)
3.3V OUTPUT VOLTAGE
vs. LOAD CURRENT
80
60
SKIP MODE
PWM MODE
2
0.0
OUTPUT VOLTAGE (V)
20V
3
PWM MODE
10
SKIP MODE
EFFICIENCY (%)
EFFICIENCY (%)
12V
80
0.01
0.1
1
LOAD CURRENT (A)
90
60
OUTPUT VOLTAGE DEVIATION (%)
0.01
100
MAX8744 toc04
7V
90
0.001
5.00
3.3V OUTPUT EFFICIENCY
vs. LOAD CURRENT
100
50
LOW-NOISE MODE
4.90
0.001
1
2
3
LOAD CURRENT (A)
4
5
STANDBY AND SHUTDOWN INPUT CURRENT
vs. INPUT VOLTAGE
100
STANDBY (ONx = GND)
SUPPLY CURRENT (μA)
0.01
5.05
4.95
MAX8744 toc05
0.001
PWM MODE
MAX8744 toc08
50
SKIP MODE
OUTPUT VOLTAGE (V)
EFFICIENCY (%)
EFFICIENCY (%)
12V
80
5.10
MAX8744 toc06
90
SKIP MODE
10
LOW-NOISE MODE
MAX8744 toc09
7V
MAX8744 toc02
100
MAX8744 toc01
100
5V OUTPUT VOLTAGE
vs. LOAD CURRENT
MAX8744 toc03
5V OUTPUT EFFICIENCY
vs. LOAD CURRENT
SHUTDOWN
(SHDN = GND)
10
-2
SKIP MODE
1
-3
0
4
8
12
INPUT VOLTAGE (V)
16
20
1
0
4
8
12
INPUT VOLTAGE (V)
16
20
0
4
8
12
INPUT VOLTAGE (V)
16
20
_______________________________________________________________________________________
9
MAX8744/MAX8745
Typical Operating Characteristics
(Circuit of Figure 1, VIN = 12V, SKIP = GND, FSEL = REF, TA = +25°C, unless otherwise noted.)
Typical Operating Characteristics (continued)
(Circuit of Figure 1, VIN = 12V, SKIP = GND, FSEL = REF, TA = +25°C, unless otherwise noted.)
3.3V SWITCHING FREQUENCY
vs. LOAD CURRENT
2
1
LOW-NOISE MODE
SKIP = REF
0
4
8
12
INPUT VOLTAGE (V)
16
100
LOW-NOISE SKIP
PULSE SKIPPING
10
LDO5 OUTPUT VOLTAGE
vs. LOAD CURRENT
0.1
1
20
-10
-6
-2
2
6
2V REF OFFSET VOLTAGE (mV)
OUTA OUTPUT VOLTAGE
vs. LOAD CURRENT
LDO5 POWER-UP
10
MAX8744 toc15
12V
A
OUTPUT VOLTAGE (V)
5V
4.8
4.7
12.1
2V
1V
B
5V
12.0
0
5V
C
0
D
11.9
4.5
0
20
40
60
LOAD CURRENT (mA)
80
100
MAX8744 toc12
30
LOAD CURRENT (A)
4.6
10
40
10
MAX8744 toc14
4.9
SAMPLE SIZE = 125
0
0.01
12.2
MAX8744 toc13
5.0
+85°C
+25°C
10
1
0.001
20
50
MAX8744 toc11
FORCED-PWM
0
REFERENCE OFFSET VOLTAGE
DISTRIBUTION
SAMPLE PERCENTAGE (%)
IDLE-MODE CURRENT (A)
SKIP MODE
SKIP = GND
1000
SWITCHING FREQUENCY (kHz)
3
MAX8744 toc10
3.3V IDLE-MODE CURRENT
vs. INPUT VOLTAGE
OUTPUT VOLTAGE (V)
MAX8744/MAX8745
High-Efficiency, Quad Output, Main PowerSupply Controllers for Notebook Computers
0
50
100
LOAD CURRENT (mA)
150
1ms/div
A. INPUT SUPPLY, 5V/div
B. REF, 2V/div
SHDN = IN
______________________________________________________________________________________
C. LDO5, 5V/div
D. PGOOD5, 5V/div
High-Efficiency, Quad Output, Main PowerSupply Controllers for Notebook Computers
SMPS DELAYED STARTUP SEQUENCE
(ON3 = REF)
SOFT-START WAVEFORM
MAX8744 toc17
MAX8744 toc16
3.3V
0
SMPS DELAYED STARTUP SEQUENCE
(ON5 = REF)
A
3.3V
0
MAX8744 toc18
A
5V
5V
B
0
C
0
12V
B
0
0
5A
C
0
E
0
A. ON5, 5V/div
B. 5V OUTPUT (VOUT5), 5V/div
C. PGOOD5, 5V/div
ON3 = REF
D. AUX LDO OUTPUT
(VOUTA), 10V/div
E. L5 INDUCTOR CURRENT,
5A/div
SMPS SHUTDOWN WAVEFORMS
D
0
E
0
1ms/div
D. 3.3V OUTPUT (VOUT3),
5V/div
E. PGOOD3, 5V/div
A. ON3, 5V/div
B. 5V OUTPUT (VOUT5), 5V/div
C. PGOOD5, 5V/div
ON5 = REF
A
5V
B
0
0
C
3.3V
0
5V
D
MAX8744 toc21
3A
1A
5.1V
A
5.0V
B
4.9V
5A
B
3.30V
3.25V
C
1A
12V
3A
1A
C
12V
D
0
D
0
20μs/div
D. 3.3V OUTPUT (VOUT3),
5V/div
E. PGOOD3, 5V/div
A
1A
3.35V
E
1ms/div
D. 3.3V OUTPUT (VOUT3),
5V/div
E. PGOOD3, 5V/div
OUT3 LOAD TRANSIENT
MAX8744 toc20
5A
A. SHDN, 5V/div
B. 5V OUTPUT (VOUT5), 5V/div
C. PGOOD5, 5V/div
NO LOAD
C
0
OUT5 LOAD TRANSIENT
MAX8744 toc19
3.3V
0
B
1ms/div
400μs/div
A. ON3 AND ON5, 5V/div
B. 5V OUTPUT (VOUT5), 5V/div
C. PGOOD5, 5V/div
5V
3.3V
D
0
E
0
A
0
3.3V
D
3.3V
0
A. IOUT5 = 1A TO 5A, 5A/div
B. VOUT5, 50mV/div
20μs/div
C. INDUCTOR CURRENT,
5A/div
D. LX5, 10V/div
A. IOUT3 = 1A TO 3A, 5A/div
B. VOUT3, 50mV/div
C. INDUCTOR CURRENT,
5A/div
D. LX3, 10V/div
______________________________________________________________________________________
11
MAX8744/MAX8745
Typical Operating Characteristics (continued)
(Circuit of Figure 1, VIN = 12V, SKIP = GND, FSEL = REF, TA = +25°C, unless otherwise noted.)
MAX8744/MAX8745
High-Efficiency, Quad Output, Main PowerSupply Controllers for Notebook Computers
Typical Operating Characteristics (continued)
(Circuit of Figure 1, VIN = 12V, SKIP = GND, FSEL = REF, TA = +25°C, unless otherwise noted.)
OUTPUT OVERVOLTAGE
FAULT PROTECTION (MAX8744 ONLY)
SKIP TRANSITION
OUTPUT UNDERVOLTAGE
(SHORT-CIRCUIT) FAULT PROTECTION
MAX8744 toc23
MAX8744 toc22
3.3V
MAX8744 toc24
5V
A
0
A
0
3.35V
A
0
3.3V
3.3
B
3.25V
5V
B
B
0
2A
0
5V
C
12V
0
D
0
C
0
12V
5V
D
D
0
40μs/div
A. SKIP, 5V/div
B. 3.3V OUTPUT (VOUT3),
100mV/div
0.5A LOAD
0
5V
C
0
1ms/div
C. INDUCTOR CURRENT,
2A/div
D. LX3, 10V/div
A.PGOOD3, 5V/div
B. 3.3V OUTPUT (VOUT3),
2V/div
20μs/div
C. 5V OUTPUT (VOUT5),
5V/div
D. DL3, 5V/div
A. LOAD FET GATE, 5V/div
C. DL3, 5V/div
B. 3.3V OUTPUT (VOUT3), 1V/div D. DH3, 10V/div
30mΩ MOSFET
LDOHA LOAD TRANSIENT
LDOH5 LOAD TRANSIENT
MAX8744 toc26
MAX8744 toc25
5V
A
0
5.00V
A
4.95V
15.0V
B
14.5V
100mA
B
12.0V
C
11.9V
0
20μs/div
A. LDO5 OUTPUT, 50mV/div
B. LOAD CURRENT, 50mA/div
12
20μs/div
A. LOAD FET GATE, 5V/div
C. AUX LDO OUTPUT (VOUTA),
B. AUX LDO INPUT, 0.5V/div
0.1V/div
0 TO 150mA LOAD TRANSIENT
______________________________________________________________________________________
High-Efficiency, Quad Output, Main PowerSupply Controllers for Notebook Computers
PIN
NAME
FUNCTION
1
ONA
Auxiliary LDO Enable Input. When ONA is pulled low, OUTA is high impedance and the secondary
feedback control is disabled. When ONA is driven high, the controller enables the auxiliary LDO.
2
DRVA
Auxiliary LDO Transistor Base Driver. Connect DRVA to the base of a pnp power transistor. Add a
680Ω pullup resistor between the base and emitter.
ILIM
Peak Current-Limit Threshold Adjustment. The current-limit threshold defaults to 50mV if ILIM is pulled
up to LDO5. In adjustable mode, the current-limit threshold across CSH_ and CSL_ is precisely 1/10
the voltage seen at ILIM over a 0.5V to 2.0V range. The logic threshold for switchover to the 50mV
default value is approximately VLDO5 - 1V.
4
SHDN
Shutdown Control Input. The device enters its 8µA supply-current shutdown mode if V SHDN is less
than the SHDN input falling edge trip level and does not restart until V SHDN is greater than the SHDN
input rising-edge trip level. Connect SHDN to VIN for automatic startup. SHDN can be connected to
VIN through a resistive voltage-divider to implement a programmable undervoltage lockout.
5
ON3
3.3V SMPS Enable Input. Driving ON3 high enables the 3.3V SMPS, while pulling ON3 low disables
the 3.3V SMPS. If ON3 is connected to REF, the 3.3V SMPS starts after the 5V SMPS reaches
regulation (delayed start). Drive ON3 below the clear fault level to reset the fault latch.
6
ON5
5V SMPS Enable Input. Driving ON5 high enables the 5V SMPS, while pulling ON5 low disables the
5V SMPS. If ON5 is connected to REF, the 5V SMPS starts after the 3.3V SMPS reaches regulation
(delayed start). Drive ON5 below the clear fault level to reset the fault latch.
7
REF
2.0V Reference Voltage Output. Bypass REF to analog ground with a 0.1µF or greater ceramic
capacitor. The reference sources up to 50µA for external loads. Loading REF degrades outputvoltage accuracy according to the REF load-regulation error. The reference shuts down when the
system pulls SHDN low.
8
GND
Analog Ground. Connect the exposed backside pad to GND.
9
FSEL
Frequency Select Input. This three-level logic input sets the controllers’ switching frequency. Connect
to LDO5, REF, or GND to select the following typical switching frequencies:
LDO5 = 500kHz, REF = 300kHz, GND = 200kHz.
10
SKIP
Pulse-Skipping Control Input. Connect to LDO5 for low-noise, forced-PWM operation. Connect to REF
for automatic, low-noise, pulse-skipping operation at light loads. Connect to GND for automatic, highefficiency, pulse-skipping operation at light loads.
11
FB5
Feedback Input for the 5V SMPS. Connect to LDO5 for the preset 5V output. In adjustable mode, FB5
regulates to 2V.
12
CSH5
Positive Current-Sense Input for the 5V SMPS. Connect to the positive terminal of the current-sense
element. Figure 7 describes two different current-sensing options—using accurate sense resistors or
lossless inductor DCR sensing.
13
CSL5
Output-Sense and Negative Current-Sense Input for the 5V SMPS. When using the internal preset 5V
feedback-divider (FB5 = LDO5), the controller uses CSL5 to sense the output voltage. Connect to the
negative terminal of the current-sense element. CSL5 also serves as the bootstrap input for LDO5.
14
PGOOD5
3
Open-Drain, Power-Good Output for the 5V SMPS. PGOOD5 is pulled low if CSL5 drops more than
10% (typ) below the normal regulation point. PGOOD5 is held low during soft-start and shutdown.
PGOOD5 becomes high impedance when CSL5 is in regulation.
______________________________________________________________________________________
13
MAX8744/MAX8745
Pin Description
High-Efficiency, Quad Output, Main PowerSupply Controllers for Notebook Computers
MAX8744/MAX8745
Pin Description (continued)
PIN
NAME
15
BST5
16
DH5
High-Side Gate-Driver Output for the 5V SMPS. DH5 swings from LX5 to BST5.
LX5
Inductor Connection for the 5V SMPS. Connect LX5 to the switched side of the inductor. LX5 serves
as the lower supply rail for the DH5 high-side gate driver.
18
DL5
Low-Side Gate-Driver Output for the 5V SMPS. DL5 swings from PGND to LDO5.
19
PGND
Power Ground
20
LDO5
5V Internal Linear-Regulator Output. Bypass with 4.7µF minimum (1µF/25mA). Provides at least
100mA for the DL_ low-side gate drivers, the DH_ high-side drivers through the BST switches, the
PWM controller, logic, reference, and external loads. If CSL5 is greater than 4.5V and soft-start is
complete, the linear regulator shuts down, and LDO5 connects to CSL5 through a 1Ω switch rated for
loads up to 200mA.
21
IN
22
PGOODA
23
DL3
24
LX3
25
DH3
26
BST3
27
PGOOD3
Open-Drain, Power-Good Output for the 3.3V SMPS. PGOOD3 is pulled low if CSL3 drops more than
10% (typ) below the normal regulation point. PGOOD3 is held low during soft-start and shutdown.
PGOOD3 becomes high impedance when CSL3 is in regulation.
28
CSL3
Output Sense and Negative Current Sense for the 3.3V SMPS. When using the internal preset 3.3V
feedback divider (FB3 = LDO5), the controller uses CSL3 to sense the output voltage. Connect to the
negative terminal of the current-sense element.
29
CSH3
Positive Current-Sense Input for the 3.3V SMPS. Connect to the positive terminal of the current-sense
element. Figure 7 describes two different current-sensing options—using accurate sense resistors or
lossless inductor DCR sensing.
30
FB3
Feedback Input for the 3.3V SMPS. Connect to LDO5 for fixed 3.3V output. In adjustable mode, FB3
regulates to 2V.
17
14
FUNCTION
Boost Flying Capacitor Connection for the 5V SMPS. The MAX8744/MAX8745 include an internal
boost switch connected between LDO5 and BST5. Connect to an external capacitor as shown in
Figure 1.
Input of the Startup Circuitry and the LDO5 Internal 5V Linear Regulator. Bypass to PGND with a
0.22µF or greater ceramic capacitor close to the IC.
Open-Drain, Power-Good Output for the Auxiliary LDO. PGOODA is pulled low if FBA drops more
than 10% (typ) below the normal regulation point, and when the auxiliary LDO is shut down. PGOODA
becomes high impedance when FBA is in regulation.
Low-Side Gate-Driver Output for the 3.3V SMPS. DL3 swings from PGND to LDO5.
Inductor Connection for the 3.3V SMPS. Connect LX3 to the switched side of the inductor. LX3 serves
as the lower supply rail for the DH3 high-side gate driver.
High-Side Gate-Driver Output for the 3.3V SMPS. DH3 swings from LX3 to BST3.
Boost Flying Capacitor Connection for the 3.3V SMPS. The MAX8744/MAX8745 include an internal
boost switch connected between LDO5 and BST3. Connect to an external capacitor as shown in
Figure 1.
______________________________________________________________________________________
High-Efficiency, Quad Output, Main PowerSupply Controllers for Notebook Computers
PIN
NAME
31
FBA
32
OUTA
EP
EP
FUNCTION
Auxiliary LDO Feedback Input. Connect a resistive voltage-divider from OUTA to analog ground to
adjust the auxiliary linear-regulator output voltage. FBA regulates at 1V.
Adjustable Auxiliary Linear-Regulator Output. Bypass OUTA to GND with 1µF or greater capacitor
(1µF/25mA). When DRVA < OUTA, the secondary feedback control triggers the DL5 for 1µs forcing
the controller to recharge the auxiliary storage capacitor. When DRVA exceeds 25V, the
MAX8744/MAX8745 enable a 10mA shunt on OUTA, preventing the storage capacitor from rising to
unsafe levels due to the transformer’s leakage inductance. Pulling ONA high enables the linearregulator driver and the secondary feedback control.
Exposed Pad. Connect the exposed backside pad to analog ground.
Table 1. Component Selection for Standard Applications
300kHz
5V AT 5A
3.3V AT 6A
COMPONENT
500kHz
5V AT 3A
3.3V AT 5A
INPUT VOLTAGE
VIN = 7V TO 24V
VIN = 7V TO 24V
CIN_, Input Capacitor
(3) 10µF, 25V
Taiyo Yuden TMK432BJ106KM
(3) 10µF, 25V
Taiyo Yuden TMK432BJ106KM
COUT5, Output Capacitor
2x 100µF, 6V, 35mΩ
Sanyo 6TPE100MAZB
2x 100µF, 6V, 35mΩ
Sanyo 6TPE100MAZB
L5/T5 Inductor/Transformer
6.8µH, 6.4A, 18mΩ (max) 1:2
Sumida 4749-T132
—
NH5 High-Side MOSFET
Fairchild Semiconductor
FDS6612A
International Rectifier
IRF7807V
Fairchild Semiconductor
FDS6612A
International Rectifier
IRF7807V
NL5 Low-Side MOSFET
Fairchild Semiconductor
FDS6670S
International Rectifier
IRF7807VD1
Fairchild Semiconductor
FDS6670S
International Rectifier
IRF7807VD1
COUT3, Output Capacitor
2x 150µF, 4V, 35mΩ
Sanyo 4TPE150MAZB
2x 100µF, 6V, 35mΩ
Sanyo 6TPE100MAZB
L3, Inductor
5.7µH, 9A, 8.5mΩ
TDK RLF12560T-5R6N9R2
3.9µH, 6.5A, 15mΩ
Sumida CDRH124-3R9NC
NH3 High-Side MOSFET
Fairchild Semiconductor
FDS6612A
International Rectifier
IRF7807V
Fairchild Semiconductor
FDS6612A
International Rectifier
IRF7807V
NL3 Low-Side MOSFET
Fairchild Semiconductor
FDS6670S
International Rectifier
IRF7807VD1
Fairchild Semiconductor
FDS6670S
International Rectifier
IRF7807VD1
5V OUTPUT
3V OUTPUT
______________________________________________________________________________________
15
MAX8744/MAX8745
Pin Description (continued)
MAX8744/MAX8745
High-Efficiency, Quad Output, Main PowerSupply Controllers for Notebook Computers
CIN
INPUT (VIN)
CIN
IN
21
D1
NH1
25
26
CBST1
0.1μF
L1
3.3V PWM
OUTPUT
COUT1
R1
5.62kΩ
R2
3.92kΩ
24
23
DL1
DH3
DH5
BST3
BST5
LX3
LX5
DL5
DL3
NL1
28
CSH3
CSH5
CSL3
CSL5
C3
1000pF
ILIM
REF
(300kHz)
9
7
FSEL
FB5
REF
FB3
CREF
0.22μF
LDO5
SECONDARY
OUTPUT
2
32
CLDOA
4.7μF
T1
CBST2
0.1μF
17
5V PWM
OUTPUT
18
NL2
DL2
12
R3
10.5kΩ
R4
4.02kΩ
13
C2
0.22μF
3
C4
1000pF
COUT2
11
30
20
CLDO5
4.7μF
5V LDO OUTPUT
DRVA
SKIP
10
OUTA
R5
110kΩ
31
CONNECT
TO 5V OR 3.3V
FBA
R7
100kΩ
R6
10kΩ
PGOODA
PGOOD3
4
5
ON OFF
6
1
SHDN
PGOOD5
R8
100kΩ
R9
100kΩ
22
27
POWER-GOOD
14
ON3
ON5
ONA
POWER GROUND
ANALOG GROUND
SEE TABLE 1 FOR COMPONENT SPECIFICATIONS.
Figure 1. Standard Application Circuit
16
SECONDARY
OUTPUT
MAX8744
MAX8745
R10
680Ω
12V LDO
OUTPUT
CAUX
4.7μF
15
19
PGND
8
GND
29
C1
0.22μF
NH2
16
______________________________________________________________________________________
High-Efficiency, Quad Output, Main PowerSupply Controllers for Notebook Computers
SUPPLIER
WEBSITE
AVX
www.avx.com
Central Semiconductor
Fairchild
www.centralsemi.com
International Rectifier
www.irf.com
www.fairchildsemi.com
Kemet
www.kemet.com
NEC/Tokin
www.nec-tokin.com
Panasonic
www.panasonic.com/industrial
Phillips
www.phillips.com
Pulse
www.pulseeng.com
Renesas
www.renesas.com
Sanyo
www.secc.co.jp
Sumida
www.sumida.com
Taiyo Yuden
www.t-yuden.com
TDK
www.component.tdk.com
TOKO
www.tokoam.com
Vishay (Dale, Siliconix)
www.vishay.com
Detailed Description
The MAX8744/MAX8745 standard application circuit
(Figure 1) generates the 5V/5A and 3.3V/5A typical of the
main supplies in a notebook computer. The input supply
range is 7V to 24V. See Table 1 for component selections, while Table 2 lists the component manufacturers.
The MAX8744/MAX8745 contain two interleaved, fixedfrequency, step-down controllers designed for low-voltage power supplies. The optimal interleaved architecture
guarantees out-of-phase operation, reducing the input
capacitor ripple. One internal LDO generates the keepalive 5V power. The MAX8744/MAX8745 have an auxiliary LDO with an adjustable output for generating either
the 3.3V keep-alive supply or regulating the low-power
12V system supply.
Fixed 5V Linear Regulator (LDO5)
An internal linear regulator produces a preset 5V lowcurrent output. LDO5 powers the gate drivers for the
external MOSFETs, and provides the bias supply
required for the SMPS analog controller, reference, and
logic blocks. LDO5 supplies at least 100mA for external and internal loads, including the MOSFET gate
drive, which typically varies from 5mA to 50mA,
depending on the switching frequency and external
MOSFETs selected. Bypass LDO5 with a 4.7µF or
greater ceramic capacitor (1µF per 25mA of load) to
guarantee stability under the full-load conditions.
The MAX8744/MAX8745 switch-mode power supplies
(SMPS) require a 5V bias supply in addition to the highpower input supply (battery or AC adapter). This 5V bias
supply is generated by the controller’s internal 5V linear
regulator (LDO5). This bootstrapped LDO allows the
controller to power up independently. The gate-driver
input supply is connected to the fixed 5V linear-regulator
output (LDO5). Therefore, the 5V LDO supply must provide LDO5 (PWM controller) and the gate-drive power,
so the maximum supply current required is:
IBIAS = ICC + fSW (QG(LOW) + QG(HIGH))
= 5mA to 50mA (typ)
where ICC is 0.7mA (typ), fSW is the switching frequency,
and Q G(LOW) and Q G(HIGH) are the MOSFET data
sheet’s total gate-charge specification limits at VGS = 5V.
SMPS to LDO Bootstrap Switchover
When the 5V main output voltage is above the LDO5
bootstrap-switchover threshold and has completed
soft-start, an internal 1Ω (typ) p-channel MOSFET
shorts CSL5 to LDO5, while simultaneously shutting
down the LDO5 linear regulator. This bootstraps the
device, powering the internal circuitry and external
loads from the 5V SMPS output (CSL5), rather than
through the linear regulator from the battery. Bootstrapping reduces power dissipation due to gate
charge and quiescent losses by providing power from
a 90%-efficient switch-mode source, rather than from a
much-less-efficient linear regulator. The current capability increases from 100mA to 200mA when the LDO5
output is switched over to CSL5. When ON5 is pulled
low, the controller immediately disables the bootstrap
switch and reenables the 5V LDO.
Reference (REF)
The 2V reference is accurate to ±1% over temperature
and load, making REF useful as a precision system reference. Bypass REF to GND with a 0.1µF or greater
ceramic capacitor. The reference sources up to 50µA
and sinks 5µA to support external loads. If highly accurate specifications are required for the main SMPS output voltages, the reference should not be loaded.
Loading the reference reduces the LDO5, CSL5
(OUT5), CSL3 (OUT3), and OUTA output voltages
slightly because of the reference load-regulation error.
System Enable/Shutdown (SHDN)
Drive SHDN below the precise SHDN input falling-edge
trip level to place the MAX8744/MAX8745 in its lowpower shutdown state. The controller consumes only
8µA of quiescent current while in shutdown mode.
When shutdown mode activates, the reference turns off
after the controller completes the shutdown sequence
______________________________________________________________________________________
17
MAX8744/MAX8745
Table 2. Component Suppliers
MAX8744/MAX8745
High-Efficiency, Quad Output, Main PowerSupply Controllers for Notebook Computers
IN
FSEL
SHDN
5V LINEAR
REGULATOR
OSC
LDO5
LDO BYPASS
CIRCUITRY
ILIM
SKIP
CSH5
CSL5
CSH3
CSL3
LDO5
BST3
PWM5
CONTROLLER
(FIGURE 3)
PWM3
CONTROLLER
(FIGURE 3)
DH3
LX3
BST5
DH5
LX5
LDO5
DL5
LDO5
DL3
PGND
FB3
ON5
FB
DECODE
(FIGURE 5)
FB
DECODE INTERNAL
(FIGURE 5) FB
FB5
ON3
REF
PGOODA
POWER-GOOD AND FAULT
PROTECTION
(FIGURE 6)
R
SECONDARY
FEEDBACK
PGOOD3
FAULT
PGOOD5
2.0V
REF
GND
R
DRVA
AUXILIARY
LINEAR REGULATOR
OUTA
FBA
ONA
MAX8744
MAX8745
Figure 2. Functional Diagram
18
______________________________________________________________________________________
High-Efficiency, Quad Output, Main PowerSupply Controllers for Notebook Computers
INPUTS*
MODE
OUTPUTS
SHDN
ON5
ON3
Shutdown Mode
Low
X
X
OFF
OFF
OFF
Standby Mode
High
Low
Low
ON
OFF
OFF
Normal Operation
High
High
High
ON
ON
ON
3.3V SMPS Active
High
Low
High
ON
OFF
ON
5V SMPS Active
High
High
Low
OFF
LDO5 to CSL5 bypass
switch enabled
ON
OFF
Normal Operation
(Delayed 5V SMPS
Startup)
High
Ref
High
OFF
LDO5 to CSL5 bypass
switch enabled
ON
Power-up after 3.3V
SMPS is in regulation
ON
Normal Operation
(Delayed 3.3V SMPS
Startup)
High
High
Ref
OFF
LDO5 to CSL5 bypass
switch enabled
ON
ON
Power-up after 5V
SMPS is in regulation
LDO5
5V SMPS
3V SMPS
*SHDN is an accurate, low-voltage logic input with 1V falling-edge threshold voltage and 1.6V rising-edge threshold voltage. ON3
and ON5 are tri-level CMOS logic inputs, a logic-low voltage is less than 0.8V, a logic-high voltage is greater than 2.4V, and the middle-logic level is between 1.7V and 2.3V (see the Electrical Characteristics table).
making the threshold to exit shutdown less accurate. To
guarantee startup, drive SHDN above 2V (SHDN input
rising-edge trip level). For automatic shutdown and
startup, connect SHDN to VIN. The accurate 1V fallingedge threshold on SHDN can be used to detect a specific input voltage level and shut the device down. Once
in shutdown, the 1.6V rising-edge threshold activates,
providing sufficient hysteresis for most applications.
reach their nominal regulation voltage 2ms after the
SMPS controllers are enabled (see the Soft-Start
Waveforms in the Typical Operating Characteristics).
This gradual slew rate effectively reduces the input
surge current by minimizing the current required to
charge the output capacitors (IOUT = ILOAD + COUT
VOUT(NOM) / tSLEW).
SMPS POR, UVLO, and Soft-Start
ON3 and ON5 control SMPS power-up sequencing.
ON3 or ON5 rising above 2.4V enables the respective
outputs. ON3 or ON5 falling below 1.6V disables the
respective outputs. Driving ON_ below 0.8V clears the
overvoltage, undervoltage, and thermal fault latches.
Power-on reset (POR) occurs when LDO5 rises above
approximately 1V, resetting the undervoltage, overvoltage, and thermal-shutdown fault latches. The POR circuit also ensures that the low-side drivers are pulled
high until the SMPS controllers are activated. Figure 2
is the MAX8744/MAX8745 block diagram.
The LDO5 input undervoltage-lockout (UVLO) circuitry
inhibits switching if the 5V bias supply (LDO5) is below
its 4V UVLO threshold. Once the 5V bias supply
(LDO5) rises above this input UVLO threshold and the
SMPS controllers are enabled (ON_ driven high), the
SMPS controllers start switching, and the output voltages begin to ramp up using soft-start. If the LDO5
voltage drops below the UVLO threshold, the controller
stops switching and pulls the low-side gate drivers low
until the LDO5 voltage recovers or drops below the
POR threshold.
The internal soft-start gradually increases the feedback
voltage with a 1V/ms slew rate. Therefore, the outputs
SMPS Enable Controls (ON3, ON5)
SMPS Power-Up Sequencing
Connecting ON3 or ON5 to REF forces the respective
outputs off while the other output is below regulation
and starts after that output regulates. The second
SMPS remains on until the first SMPS turns off, the
device shuts down, a fault occurs, or LDO5 goes into
UVLO. Both supplies begin their power-down
sequence immediately when the first supply turns off.
Output Discharge (Soft-Shutdown)
When the switching regulators are disabled—when ON_
or SHDN is pulled low, or when an output undervoltage
fault occurs—the internal soft-shutdown gradually
decreases the feedback voltage with a 0.5V/ms slew
rate. Therefore, the regulation voltage drops to 0V with-
______________________________________________________________________________________
19
MAX8744/MAX8745
Table 3. Operating Mode Truth Table
MAX8744/MAX8745
High-Efficiency, Quad Output, Main PowerSupply Controllers for Notebook Computers
FROM FB
(SEE FIGURE 5)
REF
SOFTSTART/STOP
SLOPE COMP
ON_
SKIP
OSC
AGND
FSEL
TRI-LEVEL
DECODE
R
Q
DH DRIVER
S
0.2 x VLIMIT
0.1 x VLIMIT
IDLE MODE
CURRENT
ILIM
A = 1/10
PEAK CURRENT
LIMIT
A = 1.2
NEG CURRENT
LIMIT
CSL_
S
Q
CSH_
R
DL DRIVER
ZERO
CROSSING
PGND
DRVA
ONE-SHOT
OUTA
5V SMPS ONLY
Figure 3. PWM Controller Functional Diagram
in 4ms after the SMPS controllers are disabled (see the
soft-shutdown waveforms in the Typical Operating
Characteristics). This slowly discharges the output
capacitance, eliminating the negative output voltages
caused by quickly discharging the output through the
inductor and low-side MOSFET. When an SMPS target
20
voltage discharges to 0.1V, its low-side driver (DL_) is
forced high, clamping the respective SMPS output to
GND. The reference remains active to provide an accurate threshold and to provide overvoltage protection.
Both SMPS controllers contain separate soft-shutdown
circuits.
______________________________________________________________________________________
High-Efficiency, Quad Output, Main PowerSupply Controllers for Notebook Computers
FSEL
SWITCHING FREQUENCY (kHz)
LDO5
500
REF
300
GND
200
Fixed-Frequency, Current-Mode
PWM Controller
The heart of each current-mode PWM controller is a
multi-input, open-loop comparator that sums two signals: the output-voltage error signal with respect to the
reference voltage and the slope-compensation ramp
(Figure 3). The MAX8744/MAX8745 use a direct-summing configuration, approaching ideal cycle-to-cycle
control over the output voltage without a traditional
error amplifier and the phase shift associated with it.
Frequency Selection (FSEL)
The FSEL input selects the PWM mode switching frequency. Table 4 shows the switching frequency based
on FSEL connection. High-frequency (500kHz) operation
optimizes the application for the smallest component
size, trading off efficiency due to higher switching losses.
This may be acceptable in ultraportable devices where
the load currents are lower. Low-frequency (200kHz)
operation offers the best overall efficiency at the expense
of component size and board space.
Forced-PWM Mode
The low-noise forced-PWM mode (SKIP = LDO5) disables the zero-crossing comparator, which controls the
low-side switch on-time. This forces the low-side gatedrive waveform to be constantly the complement of the
high-side gate-drive waveform, so the inductor current
reverses at light loads while DH_ maintains a duty factor
of VOUT/VIN. The benefit of forced-PWM mode is to keep
the switching frequency fairly constant. However, forcedPWM operation comes at a cost: the no-load 5V supply
current remains between 20mA to 50mA, depending on
the external MOSFETs and switching frequency.
Forced-PWM mode is most useful for avoiding audiofrequency noise and improving load-transient
response. Since forced-PWM operation disables the
zero-crossing comparator, the inductor current reverses under light loads.
Light-Load Operation Control (SKIP)
The MAX8744/MAX8745 include a light-load operating
mode control input (SKIP) used to enable or disable
the zero-crossing comparator for both switching regulators. When the zero-crossing comparator is enabled,
the regulator forces DL_ low when the current-sense
inputs detect zero inductor current. This keeps the
inductor from discharging the output capacitors and
forces the regulator to skip pulses under light-load conditions to avoid overcharging the output. When the
zero-crossing comparator is disabled, the regulator is
forced to maintain PWM operation under light-load conditions (forced-PWM).
Idle Mode Current-Sense Threshold
When pulse-skipping mode is enabled, the on-time of the
step-down controller terminates when the output voltage
exceeds the feedback threshold and when the currentsense voltage exceeds the Idle Mode current-sense
threshold. Under light-load conditions, the on-time duration depends solely on the Idle Mode current-sense
threshold, which is 20% (SKIP = GND) of the full-load
current-limit threshold set by ILIM, or the low-noise current-sense threshold, which is 10% (SKIP = REF) of the
full-load current-limit threshold set by ILIM. This forces
the controller to source a minimum amount of power with
each cycle. To avoid overcharging the output, another
on-time cannot begin until the output voltage drops
below the feedback threshold. Since the zero-crossing
comparator prevents the switching regulator from sinking
current, the controller must skip pulses. Therefore, the
controller regulates the valley of the output ripple under
light-load conditions.
Automatic Pulse-Skipping Crossover
In skip mode, an inherent automatic switchover to PFM
takes place at light loads (Figure 4). This switchover is
affected by a comparator that truncates the low-side
switch on-time at the inductor current’s zero crossing.
The zero-crossing comparator senses the inductor current across CSH_ to CSL_. Once VCSH_ - VCSL_ drops
below the 3mV zero-crossing, current-sense threshold,
the comparator forces DL_ low (Figure 3). This mechanism causes the threshold between pulse-skipping
PFM and nonskipping PWM operation to coincide with
the boundary between continuous and discontinuous
inductor-current operation (also known as the “critical
conduction” point). The load-current level at which
PFM/PWM crossover occurs, ILOAD(SKIP), is given by:
ILOAD(SKIP) =
(VIN − VOUT )VOUT
2VINfOSCL
The switching waveforms may appear noisy and asynchronous when light loading causes pulse-skipping
operation, but this is a normal operating condition that
results in high light-load efficiency. Trade-offs in PFM
noise vs. light-load efficiency are made by varying the
inductor value. Generally, low inductor values produce
______________________________________________________________________________________
21
MAX8744/MAX8745
Table 4. FSEL Configuration Table
a broader efficiency vs. load curve, while higher values
result in higher full-load efficiency (assuming that the
coil resistance remains fixed) and less output-voltage
ripple. Penalties for using higher inductor values
include larger physical size and degraded load-transient response (especially at low input-voltage levels).
Output Voltage
DC output accuracy specifications in the Electrical
Characteristics table refer to the error comparator’s
threshold. When the inductor continuously conducts,
the MAX8744/MAX8745 regulate the peak of the output
ripple, so the actual DC output voltage is lower than the
slope-compensated trip level by 50% of the output ripple voltage. For PWM operation (continuous conduction), the output voltage is accurately defined by the
following equation:
⎛ A
⎞ ⎛V
V
⎞
VOUT(PWM) = VNOM ⎜1− SLOPE RIPPLE ⎟ − ⎜ RIPPLE ⎟
⎠
2
VIN
⎝
⎠ ⎝
where V NOM is the nominal output voltage, A SLOPE
equals 1%, and VRIPPLE is the output ripple voltage
(V RIPPLE = ESR x ΔI INDUCTOR, as described in the
Output Capacitor Selection section).
In discontinuous conduction (IOUT < ILOAD(SKIP)), the
MAX8744/MAX8745 regulate the valley of the output
ripple, so the output voltage has a DC regulation level
higher than the error-comparator threshold. For PFM
operation (discontinuous conduction), the output voltage is approximately defined by the following equation:
VOUT(PFM) = VNOM +
1 ⎛ fSW ⎞
IIDLEESR
2 ⎜⎝ fOSC ⎟⎠
where VNOM is the nominal output voltage, fOSC is the
maximum switching frequency set by the internal oscillator, fSW is the actual switching frequency, and IIDLE is
the Idle Mode inductor current when pulse skipping.
Connect FB3 and FB5 to LDO5 to enable the fixed
SMPS output voltages (3.3V and 5V, respectively), set
by a preset, internal resistive voltage-divider connected
between the output (CSL_) and analog ground.
Connect a resistive voltage-divider at FB_ between the
output (CSL_) and GND to adjust the respective output
voltage between 2V and 5.5V (Figure 5). Choose RFBLO
(resistance from FB to AGND) to be approximately
10kΩ and solve for RFBHI (resistance from the output to
FB) using the equation:
⎛ VOUT _ ⎞
RFBHI = RFBLO ⎜
−1⎟
⎝ VFB _
⎠
where VFB_ = 2V nominal.
When adjusting both output voltages, set the 3.3V
SMPS lower than the 5V SMPS. LDO5 connects to the
TO ERROR
AMPLIFIER
ADJUSTABLE
OUTPUT
FB
tON(SKIP) =
LDO5
VOUT
VINfOSC
INDUCTOR CURRENT
MAX8744/MAX8745
High-Efficiency, Quad Output, Main PowerSupply Controllers for Notebook Computers
R
9R
IPK
ILOAD = IPK / 2
OUT
0
FIXED OUTPUT
FB = LDO5
TIME
ON-TIME
Figure 4. Pulse-Skipping/Discontinuous Crossover Point
22
Figure 5. Dual Mode Feedback Decoder
______________________________________________________________________________________
High-Efficiency, Quad Output, Main PowerSupply Controllers for Notebook Computers
Current-Limit Protection (ILIM)
The current-limit circuit uses differential current-sense
inputs (CSH_ and CSL_) to limit the peak inductor current. If the magnitude of the current-sense signal
exceeds the current-limit threshold, the PWM controller
turns off the high-side MOSFET (Figure 3). The actual
maximum load current is less than the peak currentlimit threshold by an amount equal to half of the inductor ripple current. Therefore, the maximum load
capability is a function of the current-sense resistance,
inductor value, switching frequency, and duty cycle
(VOUT/VIN).
In forced-PWM mode, the MAX8744/MAX8745 also
implement a negative current limit to prevent excessive
reverse inductor currents when VOUT is sinking current.
The negative current-limit threshold is set to approximately 120% of the positive current limit and tracks the
positive current limit when ILIM is adjusted.
Connect ILIM to LDO5 for the 50mV default threshold,
or adjust the current-limit threshold with an external
resistor-divider at ILIM. Use a 2µA to 20µA divider current for accuracy and noise immunity. The current-limit
threshold adjustment range is from 50mV to 200mV. In
the adjustable mode, the current-limit threshold voltage
equals precisely 1/10 the voltage seen at ILIM. The
logic threshold for switchover to the default value is
approximately VLDO5 - 1V.
MOSFET Gate Drivers (DH_, DL_)
The DH_ and DL_ drivers are optimized for driving
moderate-sized high-side and larger low-side power
MOSFETs. This is consistent with the low duty factor
seen in notebook applications, where a large V IN V OUT differential exists. The high-side gate drivers
(DH_) source and sink 2A, and the low-side gate drivers (DL_) source 1.7A and sink 3.3A. This ensures
robust gate drive for high-current applications. The
DH_ floating high-side MOSFET drivers are powered by
charge pumps at BST_ while the DL_ synchronous-rectifier drivers are powered directly by the fixed 5V linear
regulator (LDO5).
Adaptive dead-time circuits monitor the DL_ and DH_
drivers and prevent either FET from turning on until the
other is fully off. The adaptive driver dead-time allows
operation without shoot-through with a wide range of
MOSFETs, minimizing delays and maintaining efficiency.
There must be a low-resistance, low-inductance path
from the DL_ and DH_ drivers to the MOSFET gates for
the adaptive dead-time circuits to work properly; otherwise, the sense circuitry in the MAX8744/ MAX8745 interprets the MOSFET gates as “off” while charge actually
remains. Use very short, wide traces (50 mils to 100 mils
wide if the MOSFET is in from the driver).
The internal pulldown transistor that drives DL_ low is
robust, with a 0.6Ω (typ) on-resistance. This helps prevent
DL_ from being pulled up due to capacitive coupling from
the drain to the gate of the low-side MOSFETs when the
inductor node (LX_) quickly switches from ground to VIN.
FAULT
PROTECTION
POWER GOOD
0.9 x INT REF_
0.7 x INT REF_
1.11 x INT REF_
INTERNAL FB
Carefully observe the PC board layout guidelines to
ensure that noise and DC errors do not corrupt the differential current-sense signals seen by CSH_ and
CSL_. Place the IC close to the sense resistor with
short, direct traces, making a Kelvin-sense connection
to the current-sense resistor.
ENABLE OVP
ENABLE UVP
6144
CLK
FAULT
LATCH
FAULT
POWER-GOOD
POR
Figure 6. Power-Good and Fault Protection
______________________________________________________________________________________
23
MAX8744/MAX8745
5V output (CSL5) through an internal switch only when
CSL5 is above the LDO5 bootstrap threshold (4.5V)
and the soft-start sequence for the CSL5 side has completed. Bootstrapping works most effectively when the
fixed output voltages are used. Once LDO5 is bootstrapped from CSL5, the internal 5V linear regulator
turns off. This reduces the internal power dissipation
and improves efficiency at higher input voltages.
MAX8744/MAX8745
High-Efficiency, Quad Output, Main PowerSupply Controllers for Notebook Computers
Table 5. Operating Modes Truth Table
MODE
CONDITION
COMMENT
Power-Up
LDO5 < UVLO threshold
Transitions to discharge mode after VIN POR and after REF
becomes valid. LDO5, REF remain active. DL_ is active
(high).
Run
SHDN = high, ON3 or ON5 enabled
Normal operation.
Output Overvoltage
(OVP) Protection
(MAX8744)
Either output > 111% of nominal level
Exited by POR or cycling SHDN, ON3, or ON5.
Output Undervoltage
Protection (UVP)
Either output < 70% of nominal level,
UVP is enabled 6144 clock cycles
(1/fOSC) after the output is enabled
Exited by POR or cycling SHDN, ON3, or ON5.
Standby
ON5 and ON3 < startup threshold,
SHDN = high
DL_ stays high. LDO5 active.
Shutdown
SHDN = low
All circuitry off.
Thermal Shutdown
TJ > +160°C
Exited by POR or cycling SHDN, ON3, or ON5.
DL3 and DL5 go high before LDO5 turns off. They remain
high as long as possible thereafter.
Switchover Fault
Excessive current on LDO5 switchover
transistors
Exited by POR or cycling SHDN, ON3, or ON5.
Applications with high input voltages and long inductive
driver traces may require additional gate-to-source
capacitance to ensure fast-rising LX_ edges do not pull
up the low-side MOSFETs gate, causing shoot-through
currents. The capacitive coupling between LX_ and DL_
created by the MOSFET’s gate-to-drain capacitance
(CGD = CRSS), gate-to-source capacitance (CGS = CISS
- C GD ), and additional board parasitics should not
exceed the following minimum threshold.
⎛C
⎞
VGS(TH) > VIN ⎜ RSS ⎟
⎝ CISS ⎠
Lot-to-lot variation of the threshold voltage may cause
problems in marginal designs.
Power-Good Output (PGOOD_)
PGOOD_ is the open-drain output of a comparator that
continuously monitors both SMPS output voltages and
the auxiliary LDO output for undervoltage conditions.
PGOOD_ is actively held low in shutdown (SHDN =
GND), standby (ON3 = ON5 = ONA = GND), soft-start,
and soft-shutdown. Once the soft-start sequence terminates, PGOOD_ becomes high impedance as long as
the outputs are above 90% of the nominal regulation voltage set by FB_. PGOOD_ goes low once the respective
output drops 10% below its nominal regulation point, an
24
SMPS output overvoltage fault occurs, or ON_ or SHDN
is low. For a logic-level PGOOD_ output voltage, connect
an external pullup resistor between PGOOD_ and LDO5.
A 100kΩ pullup resistor works well in most applications.
Fault Protection
Output Overvoltage Protection (OVP)—
MAX8744 Only
If the output voltage of either SMPS rises above 111% of
its nominal regulation voltage and the OVP protection is
enabled, the controller sets the fault latch, pulls PGOOD
low, shuts down the SMPS controllers that tripped the
fault, and immediately pulls DH_ low and forces DL_
high. This turns on the synchronous-rectifier MOSFETs
with 100% duty, rapidly discharging the output capacitors and clamping both outputs to ground. However,
immediately latching DL_ high typically causes slightly
negative output voltages due to the energy stored in the
output LC at the instant the OVP occurs. If the load cannot tolerate a negative voltage, place a power Schottky
diode across the output to act as a reverse-polarity
clamp. If the condition that caused the overvoltage persists (such as a shorted high-side MOSFET), the battery
blows. The other output is shut down using the soft-shutdown sequence. Cycle LDO5 below 1V or toggle either
ON3, ON5, or SHDN to clear the fault latch and restart
the SMPS controllers.
______________________________________________________________________________________
High-Efficiency, Quad Output, Main PowerSupply Controllers for Notebook Computers
Thermal Fault Protection
The MAX8744/MAX8745 feature a thermal fault-protection circuit. When the junction temperature rises above
+160°C, a thermal sensor activates the fault latch, pulls
PGOOD low, and shuts down both SMPS controllers
using the soft-shutdown sequence. When an SMPS output voltage drops to 0.1V, its synchronous rectifier
turns on, clamping the discharged output to GND.
Toggle either ON3, ON5, or SHDN to clear the fault
latch and restart the controllers after the junction temperature cools by 15°C.
Auxiliary LDO Detailed Description
The MAX8744/MAX8745 include an auxiliary linear regulator (OUTA) that can be configured for 12V, ideal for
PCMCIA power requirements, and for biasing the gates
of load switches in a portable device. OUTA can also be
configured for outputs from 1V to 23V. The auxiliary regulator has an independent ON/OFF control, allowing it to
be shut down when not needed, reducing power consumption when the system is in a low-power state.
A flyback-winding control loop regulates a secondary
winding output, improving cross-regulation when the primary output is lightly loaded or when there is a low inputoutput differential voltage. If VDRVA - VOUTD, the low-side
switch is turned on for a time equal to 33% of the switching period. This reverses the inductor (primary) current,
pulling current from the output filter capacitor and causing the flyback transformer to operate in forward mode.
The low impedance presented by the transformer secondary in forward mode dumps current into the secondary output, charging up the secondary capacitor and
bringing VINA - VOUTA back into regulation. The secondary feedback loop does not improve secondary output accuracy in normal flyback mode, where the main
(primary) output is heavily loaded. In this condition, secondary output accuracy is determined by the secondary
rectifier drop, transformer turns ratio, and accuracy of
the main output voltage.
SMPS Design Procedure
Firmly establish the input voltage range and maximum
load current before choosing a switching frequency
and inductor operating point (ripple-current ratio). The
primary design trade-off lies in choosing a good switching frequency and inductor operating point, and the following four factors dictate the rest of the design:
• Input Voltage Range. The maximum value
(VIN(MAX)) must accommodate the worst-case, high
AC-adapter voltage. The minimum value (VIN(MIN))
must account for the lowest battery voltage after
drops due to connectors, fuses, and battery selector
switches. If there is a choice at all, lower input voltages result in better efficiency.
•
Maximum Load Current. There are two values to
consider. The peak load current (I LOAD(MAX) )
determines the instantaneous component stresses
and filtering requirements and thus drives output
capacitor selection, inductor saturation rating, and
the design of the current-limit circuit. The continuous load current (ILOAD) determines the thermal
stresses and thus drives the selection of input
capacitors, MOSFETs, and other critical heat-contributing components.
•
Switching Frequency. This choice determines the
basic trade-off between size and efficiency. The optimal frequency is largely a function of maximum input
voltage, due to MOSFET switching losses that are
proportional to frequency and VIN2. The optimum frequency is also a moving target, due to rapid improvements in MOSFET technology that are making higher
frequencies more practical.
•
Inductor Operating Point. This choice provides
trade-offs between size vs. efficiency and transient
response vs. output ripple. Low inductor values provide better transient response and smaller physical
size, but also result in lower efficiency and higher output ripple due to increased ripple currents. The minimum practical inductor value is one that causes the
circuit to operate at the edge of critical conduction
(where the inductor current just touches zero with
every cycle at maximum load). Inductor values lower
than this grant no further size-reduction benefit. The
optimum operating point is usually found between
20% and 50% ripple current. When pulse skipping
(SKIP low and light loads), the inductor value also
determines the load-current value at which
PFM/PWM switchover occurs.
Inductor Selection
The switching frequency and inductor operating point
determine the inductor value as follows:
______________________________________________________________________________________
25
MAX8744/MAX8745
Output Undervoltage Protection (UVP)
Each SMPS controller includes an output UVP protection circuit that begins to monitor the output 6144 clock
cycles (1/fOSC) after that output is enabled (ON_ pulled
high). If either SMPS output voltage drops below 70%
of its nominal regulation voltage and the UVP protection
is enabled, the UVP circuit sets the fault latch, pulls
PGOOD low, and shuts down both controllers using the
soft-shutdown sequence. When an SMPS output voltage drops to 0.1V, its synchronous rectifier turns on,
clamping the discharged output to GND. Cycle LDO5
below 1V or toggle either ON3, ON5, or SHDN to clear
the fault latch and restart the SMPS controllers.
MAX8744/MAX8745
High-Efficiency, Quad Output, Main PowerSupply Controllers for Notebook Computers
L=
VOUT (VIN − VOUT )
VINfOSCILOAD(MAX)LIR
For example: ILOAD(MAX) = 5A, VIN = 12V, VOUT = 5V,
fOSC = 300kHz, 30% ripple current or LIR = 0.3:
L=
5V x (12V − 5V )
12V x 300kHz x 5A x 0.3
= 6.50μH
Find a low-loss inductor having the lowest possible DC
resistance that fits in the allotted dimensions. Most inductor manufacturers provide inductors in standard values,
such as 1.0µH, 1.5µH, 2.2µH, 3.3µH, etc. Also look for
non-standard values, which can provide a better compromise in LIR across the input voltage range. If using a
swinging inductor (where the no-load inductance
decreases linearly with increasing current), evaluate the
LIR with properly scaled inductance values. For the
selected inductance value, the actual peak-to-peak
inductor ripple current (ΔIINDUCTOR) is defined by:
V
(V − VOUT )
ΔIINDUCTOR = OUT IN
VINfOSCL
Ferrite cores are often the best choice, although powdered iron is inexpensive and can work well at 200kHz.
The core must be large enough not to saturate at the
peak inductor current (IPEAK):
I PEAK = I LOAD(MAX) +
ΔIINDUCTOR
2
Transformer Design (for
MAX8744/MAX8745 Auxiliary Output)
A coupled inductor or transformer can be substituted
for the inductor in the 5V SMPS to create an auxiliary
output (Figure 1). The MAX8744/MAX8745 is particularly well suited for such applications because the secondary feedback threshold automatically triggers DL5
even if the 5V output is lightly loaded.
The power requirements of the auxiliary supply must be
considered in the design of the main output. The transformer must be designed to deliver the required current
in both the primary and the secondary outputs with the
proper turns ratio and inductance. The power ratings of
the synchronous-rectifier MOSFETs and the current limit
in the MAX8744/MAX8745 must also be adjusted
accordingly. Extremes of low input-output differentials,
26
widely different output loading levels, and high turns
ratios can further complicate the design due to parasitic
transformer parameters such as interwinding capacitance, secondary resistance, and leakage inductance.
Power from the main and secondary outputs is combined to get an equivalent current referred to the main
output. Use this total current to determine the current
limit (see the Setting the Current Limit section):
ITOTAL = PTOTAL / VOUT5
where ITOTAL is the equivalent output current referred
to the main output, and PTOTAL is the sum of the output
power from both the main output and the secondary
output:
N=
VSEC + VFWD
VOUT5 + VRECT + VSENSE
where LPRIMARY is the primary inductance, N is the
transformer turns ratio, VSEC is the minimum required
rectified secondary voltage, VFWD is the forward drop
across the secondary rectifier, VOUT5(MIN) is the minimum value of the main output voltage, and VRECT is the
on-state voltage drop across the synchronous-rectifier
MOSFET. The transformer secondary return is often connected to the main output voltage instead of ground in
order to reduce the necessary turns ratio. In this case,
subtract VOUT5 from the secondary voltage (VSEC VOUT5) in the transformer turns-ratio equation above.
The secondary diode in coupled-inductor applications
must withstand flyback voltages greater than 60V.
Common silicon rectifiers, such as the 1N4001, are also
prohibited because they are too slow. Fast silicon rectifiers such as the MURS120 are the only choice. The flyback voltage across the rectifier is related to the VIN VOUT difference, according to the transformer turns ratio:
VFLYBACK = VSEC + (VIN – VOUT5) x N
where N is the transformer turns ratio (secondary windings/primary windings), and VSEC is the maximum secondary DC output voltage. If the secondary winding is
returned to VOUT5 instead of ground, subtract VOUT5
from V FLYBACK in the equation above. The diode’s
reverse breakdown voltage rating must also accommodate any ringing due to leakage inductance. The
diode’s current rating should be at least twice the DC
load current on the secondary output.
Transient Response
The inductor ripple current also impacts transientresponse performance, especially at low VIN - VOUT differentials. Low inductor values allow the inductor
______________________________________________________________________________________
High-Efficiency, Quad Output, Main PowerSupply Controllers for Notebook Computers
MAX8744/MAX8745
INPUT (VIN)
CIN
MAX8744
MAX8745
DH_
SENSE RESISTOR
NH
L
LESL
RSENSE
LX_
DL_
NL
DL
R1
CEQ
COUT
L
CEQR1 = SENSE
RSENSE
PGND
CSH_
CSL_
A) OUTPUT SERIES RESISTOR SENSING
INPUT (VIN)
CIN
MAX8744
MAX8745
DH_
INDUCTOR
NH
L
RDCR
RCS =
LX_
DL_
NL
PGND
COUT
DL
R1
R2
RDCR =
( R1R2+ R2) R
L
CEQ
DCR
[R11 + R21 ]
CEQ
CSH_
CSL_
B) LOSSLESS INDUCTOR SENSING
Figure 7. Current-Sense Configurations
______________________________________________________________________________________
27
MAX8744/MAX8745
High-Efficiency, Quad Output, Main PowerSupply Controllers for Notebook Computers
current to slew faster, replenishing charge removed
from the output filter capacitors by a sudden load step.
The total output voltage sag is the sum of the voltage
sag while the inductor is ramping up, and the voltage
sag before the next pulse can occur:
VSAG =
(
L ΔILOAD(MAX)
(
)
V
VILIM
RCS = LIMIT =
10 x ILIMIT
ILIMIT
2
2COUT VIN x DMAX − VOUT
ΔILOAD(MAX) (T − ΔT)
)
+
COUT
where DMAX is maximum duty factor (see the Electrical
Characteristics), T is the switching period (1 / fOSC), and
ΔT equals VOUT/ VIN x T when in PWM mode, or L x 0.2 x
IMAX / (VIN - VOUT) when in skip mode. The amount of
overshoot during a full-load to no-load transient due to
stored inductor energy can be calculated as:
VSOAR
tighter accuracy, but also dissipate more power. Most
applications employ a current-limit threshold (VLIMIT) of
50mV to 100mV, so the sense resistor may be determined by:
For the best current-sense accuracy and overcurrent
protection, use a 1% tolerance current-sense resistor
between the inductor and output as shown in Figure
7A. This configuration constantly monitors the inductor
current, allowing accurate current-limit protection.
However, the parasitic inductance of the current-sense
resistor can cause current-limit inaccuracies, especially
when using low-value inductors and current-sense
resistors. This parasitic inductance (LSENSE) can be
canceled by adding an RC circuit across the sense
resistor with an equivalent time constant:
2
ΔILOAD(MAX) ) L
(
≈
L
CEQR1 = SENSE
RSENSE
2COUT VOUT
Setting the Current Limit
The minimum current-limit threshold must be great
enough to support the maximum load current when the
current limit is at the minimum tolerance value. The
peak inductor current occurs at ILOAD(MAX) plus half
the ripple current; therefore:
Alternatively, high-power applications that do not
require highly accurate current-limit protection may
reduce the overall power dissipation by connecting a
series RC circuit across the inductor (Figure 7B) with
an equivalent time constant:
⎛ R2 ⎞
RCS = ⎜
⎟ RDCR
⎝ R1 + R2 ⎠
ILIMIT > ILOAD(MAX) + ⎛⎜ ΔIINDUCTOR ⎞⎟
⎝
2
⎠
and:
where ILIMIT_ equals the minimum current-limit threshold voltage divided by the current-sense resistance
(RSENSE_). For the default setting, the minimum currentlimit threshold is 45mV.
Connect ILIM to LDO5 for a default 50mV current-limit
threshold. In adjustable mode, the current-limit threshold is precisely 1/10 the voltage seen at ILIM. For an
adjustable threshold, connect a resistive divider from
REF to analog ground (GND) with ILIM connected to
the center tap. The external 0.5V to 2V adjustment
range corresponds to a 50mV to 200mV current-limit
threshold. When adjusting the current limit, use 1% tolerance resistors and a divider current of approximately
10mA to prevent significant inaccuracy in the currentlimit tolerance.
The current-sense method (Figure 7) and magnitude
determines the achievable current-limit accuracy and
power loss. Typically, higher current-sense limits provide
28
RDCR =
L ⎡1
1⎤
+
⎢
CEQ ⎣ R1 R2 ⎥⎦
where RCS is the required current-sense resistance,
and RDCR is the inductor’s series DC resistance. Use
the worst-case inductance and RDCR values provided
by the inductor manufacturer, adding some margin for
the inductance drop over temperature and load.
Output Capacitor Selection
The output filter capacitor must have low enough equivalent series resistance (ESR) to meet output ripple and
load-transient requirements, yet have high enough ESR
to satisfy stability requirements. The output capacitance must be high enough to absorb the inductor
energy while transitioning from full-load to no-load conditions without tripping the overvoltage fault protection.
When using high capacitance, low-ESR capacitors
______________________________________________________________________________________
High-Efficiency, Quad Output, Main PowerSupply Controllers for Notebook Computers
In Idle Mode, the inductor current becomes discontinuous, with peak currents set by the Idle Mode currentsense threshold (VIDLE = 0.2VLIMIT). In Idle Mode, the
no-load output ripple may be determined as follows:
V
R
VRIPPLE(P–P) = IDLE ESR
RSENSE
The actual capacitance value required relates to the
physical size needed to achieve low ESR, as well as to
the chemistry of the capacitor technology. Thus, the
capacitor is usually selected by ESR and voltage rating
rather than by capacitance value (this is true of tantalums, OS-CONs, polymers, and other electrolytics).
When using low-capacity filter capacitors, such as
ceramic capacitors, size is usually determined by the
capacity needed to prevent V SAG and V SOAR from
causing problems during load transients. Generally,
once enough capacitance is added to meet the overshoot requirement, undershoot at the rising load edge
is no longer a problem (see the VSAG and VSOAR equations in the Transient Response section). However, lowcapacity filter capacitors typically have high ESR zeros
that may affect the overall stability (see the OutputCapacitor Stability Considerations section).
Output-Capacitor Stability Considerations
Stability is determined by the value of the ESR zero relative to the switching frequency. The boundary of instability is given by the following equation:
f
fESR ≤ OSC
π
where:
fESR =
1
2πRESR COUT
For a typical 300kHz application, the ESR zero frequency must be well below 95kHz, preferably below 50kHz.
Tantalum and OS-CON capacitors in widespread use
at the time of publication have typical ESR zero frequencies of 25kHz. In the design example used for
inductor selection, the ESR needed to support 25mVP-P
ripple is 25mV/1.5A = 16.7mΩ. One 220µF/4V Sanyo
polymer (TPE) capacitor provides 15mΩ (max) ESR.
This results in a zero at 48kHz, well within the bounds
of stability.
For low-input voltage applications where the duty cycle
exceeds 50% (VOUT/VIN ≥ 50%), the output ripple voltage should not be greater than twice the internal slopecompensation voltage:
VRIPPLE ≤ 0.02 x VOUT
where VRIPPLE equals ΔIINDUCTOR x RESR. The worstcase ESR limit occurs when VIN = 2 x VOUT, so the
above equation may be simplified to provide the following boundary condition:
RESR ≤ 0.04 x L x fSW
Do not put high-value ceramic capacitors directly
across the feedback sense point without taking precautions to ensure stability. Large ceramic capacitors can
have a high ESR zero frequency and cause erratic,
unstable operation. However, it is easy to add enough
series resistance by placing the capacitors a couple of
inches downstream from the feedback sense point,
which should be as close as possible to the inductor.
Unstable operation manifests itself in two related but
distinctly different ways: short/long pulses and cycle
skipping resulting in lower frequency operation.
Instability occurs due to noise on the output or because
the ESR is so low that there is not enough voltage ramp
in the output voltage signal. This “fools” the error comparator into triggering too early or into skipping a cycle.
Cycle skipping is more annoying than harmful, resulting
in nothing worse than increased output ripple.
However, it can indicate the possible presence of loop
instability due to insufficient ESR. Loop instability can
result in oscillations at the output after line or load
steps. Such perturbations are usually damped, but can
cause the output voltage to rise above or fall below the
tolerance limits.
The easiest method for checking stability is to apply a
very fast zero-to-max load transient and carefully
observe the output-voltage-ripple envelope for overshoot and ringing. It may help to simultaneously monitor the inductor current with an AC current probe. Do
not allow more than three cycles of ringing after the initial step-response under/overshoot.
Input Capacitor Selection
The input capacitor must meet the ripple current
requirement (IRMS) imposed by the switching currents.
For an out-of-phase regulator, the total RMS current in
the input capacitor is a function of the load currents,
______________________________________________________________________________________
29
MAX8744/MAX8745
(see stability requirements), the filter capacitor’s ESR
dominates the output voltage ripple. So the output capacitor’s size depends on the maximum ESR required to meet
the output voltage ripple (VRIPPLE(P-P)) specifications:
VRIPPLE(P-P) = RESRILOAD(MAX)LIR
MAX8744/MAX8745
High-Efficiency, Quad Output, Main PowerSupply Controllers for Notebook Computers
INPUT CAPACITOR RMS CURRENT
vs. INPUT VOLTAGE
5.0
4.5
4.0
IN PHASE
IRMS (A)
3.5
3.0
50/50 INTERLEAVING
2.5
2.0
1.5
40/60 OPTIMAL
INTERLEAVING
1.0
0.5
0
0
8
10
12
14
16
18
20
VIN (V)
INPUT RMS CURRENT FOR INTERLEAVED OPERATION:
IRMS =
( OUT5
(
− IIN ) (DLX5 − DOL ) + (IOUT3 − IIN ) (DLX3 − DOL ) + IOUT5 + IOUT3 − IIN
2
2
V
V
DLX5 = OUT5
DLX3 = OUT3
VIN
VIN
VOUT5IOUT5 + VOUT3IOUT3
IIN =
VIN
)
2
DOL + IIN2 (1 − DLX5 − DLX3 + DOL
)
DOL = DUTY − CYCLE OVERLAP FRACTION
INPUT RMS CURRENT FOR SINGLE-PHASE OPERATION:
(
⎛
V
V − VOUT
⎜ OUT IN
IRMS = ILOAD ⎜
VIN
⎜
⎝
) ⎞⎟
⎟
⎟
⎠
Figure 8. Input RMS Current
the input currents, the duty cycles, and the amount of
overlap as defined in Figure 8.
The 40/60 optimal interleaved architecture of the
MAX8744/MAX8745 allows the input voltage to go as
low 8.3V before the duty cycles begin to overlap. This
offers improved efficiency over a regular 180° out-ofphase architecture where the duty cycles begin to
overlap below 10V. Figure 8 shows the input-capacitor
RMS current vs. input voltage for an application that
requires 5V/5A and 3.3V/5A. This shows the improvement of the 40/60 optimal interleaving over 50/50 interleaving and in-phase operation.
For most applications, nontantalum chemistries (ceramic, aluminum, or OS-CON) are preferred due to their
resistance to power-up surge currents typical of systems with a mechanical switch or connector in series
30
with the input. Choose a capacitor that has less than
10°C temperature rise at the RMS input current for optimal reliability and lifetime.
Power MOSFET Selection
Most of the following MOSFET guidelines focus on the
challenge of obtaining high load-current capability
when using high-voltage (> 20V) AC adapters. Lowcurrent applications usually require less attention.
The high-side MOSFET (NH) must be able to dissipate
the resistive losses plus the switching losses at both
VIN(MIN) and VIN(MAX). Ideally, the losses at VIN(MIN)
should be roughly equal to the losses at VIN(MAX), with
lower losses in between. If the losses at VIN(MIN) are
significantly higher, consider increasing the size of NH.
Conversely, if the losses at VIN(MAX) are significantly
higher, consider reducing the size of NH. If VIN does not
______________________________________________________________________________________
High-Efficiency, Quad Output, Main PowerSupply Controllers for Notebook Computers
Power MOSFET Dissipation
Worst-case conduction losses occur at the duty-factor
extremes. For the high-side MOSFET (NH), the worstcase power dissipation due to resistance occurs at minimum input voltage:
⎛V
⎞
2
PD (NH Re sistive) = ⎜ OUT ⎟ (ILOAD ) RDS(ON)
⎝ VIN ⎠
Generally, use a small high-side MOSFET to reduce
switching losses at high input voltages. However, the
RDS(ON) required to stay within package power-dissipation limits often limits how small the MOSFET can be. The
optimum occurs when the switching losses equal the
conduction (RDS(ON)) losses. High-side switching losses
do not become an issue until the input is greater than
approximately 15V.
Calculating the power dissipation in high-side MOSFETs
(NH) due to switching losses is difficult, since it must
allow for difficult-to-quantify factors that influence the turnon and turn-off times. These factors include the internal
gate resistance, gate charge, threshold voltage, source
inductance, and PC board layout characteristics. The following switching-loss calculation provides only a very
rough estimate and is no substitute for breadboard evaluation, preferably including verification using a thermocouple mounted on NH:
PD (NH Switching) =
COSS VIN(MAX) ⎞
⎛ ILOADQG(SW )
+
⎜
⎟ VIN(MAX)fSW
IGATE
2
⎝
⎠
where COSS is the output capacitance of NH, QG(SW) is
the charge needed to turn on the NH MOSFET, and IGATE
is the peak gate-drive source/sink current (1A typ).
Switching losses in the high-side MOSFET can become
a heat problem when maximum AC adapter voltages
are applied, due to the squared term in the switchingloss equation (C x VIN2 x fSW). If the high-side MOSFET
chosen for adequate RDS(ON) at low battery voltages
becomes extraordinarily hot when subjected to
V IN(MAX) , consider choosing another MOSFET with
lower parasitic capacitance.
For the low-side MOSFET (NL), the worst-case power
dissipation always occurs at maximum battery voltage:
PD (NL Re sistive) =
⎡ ⎛ VOUT ⎞ ⎤
2
⎢1 − ⎜
⎟ ⎥(ILOAD ) RDS(ON)
⎢⎣ ⎝ VIN(MAX) ⎠ ⎥⎦
The absolute worst case for MOSFET power dissipation
occurs under heavy overload conditions that are
greater than ILOAD(MAX) but are not high enough to
exceed the current limit and cause the fault latch to trip.
To protect against this possibility, “overdesign” the circuit to tolerate:
⎛ ΔI
⎞
ILOAD = ILIMIT − ⎜ INDUCTOR ⎟
⎝
⎠
2
where ILIMIT is the peak current allowed by the currentlimit circuit, including threshold tolerance and senseresistance variation. The MOSFETs must have a
relatively large heatsink to handle the overload power
dissipation.
Choose a Schottky diode (DL) with a forward-voltage
drop low enough to prevent the low-side MOSFET’s
body diode from turning on during the dead time. As a
general rule, select a diode with a DC current rating
equal to a 1/3 the load current. This diode is optional
and can be removed if efficiency is not critical.
Boost Capacitors
The boost capacitors (CBST) must be selected large
enough to handle the gate-charging requirements of
the high-side MOSFETs. Typically, 0.1µF ceramic
capacitors work well for low-power applications driving
medium-sized MOSFETs. However, high-current applications driving large, high-side MOSFETs require boost
capacitors larger than 0.1µF. For these applications,
select the boost capacitors to avoid discharging the
capacitor more than 200mV while charging the highside MOSFETs’ gates:
CBST =
QGATE
200mV
where QGATE is the total gate charge specified in the
high-side MOSFET’s data sheet. For example, assume
______________________________________________________________________________________
31
MAX8744/MAX8745
vary over a wide range, maximum efficiency is achieved
by selecting a high-side MOSFET (NH) that has conduction losses equal to the switching losses.
Choose a low-side MOSFET (NL) that has the lowest possible on-resistance (RDS(ON)), comes in a moderate-sized
package (i.e., 8-pin SO, DPAK, or D2PAK), and is reasonably priced. Ensure that the MAX8744/MAX8745 DL_
gate driver can supply sufficient current to support the
gate charge and the current injected into the parasitic
drain-to-gate capacitor caused by the high-side MOSFET
turning on; otherwise, cross-conduction problems may
occur. Switching losses are not an issue for the low-side
MOSFET since it is a zero-voltage switched device when
used in the step-down topology.
MAX8744/MAX8745
High-Efficiency, Quad Output, Main PowerSupply Controllers for Notebook Computers
the FDS6612A n-channel MOSFET is used on the high
side. According to the manufacturer’s data sheet, a single FDS6612A has a maximum gate charge of 13nC
(VGS = 5V). Using the above equation, the required
boost capacitance would be:
CBST =
13nC
= 0.065μF
200mV
Selecting the closest standard value, this example
requires a 0.1µF ceramic capacitor.
LDOA Design Procedure
Output Voltage Selection
Adjust the auxiliary linear regulator’s output voltage by
connecting a resistive divider between OUTA and analog ground with the center tap connected to FBA
(Figure 1). Select R6 in the 10kΩ to 30kΩ range, and
calculate R5 with the following equation:
⎛V
⎞
R5 = R6⎜ OUTA − 1⎟
⎝ VFBA
⎠
where VFBA = 1.0V.
Transistor Selection
The pass transistor must meet specifications for current
gain (β), input capacitance, collector-emitter saturation
voltage, and power dissipation. The transistor’s current
gain limits the guaranteed maximum output current to:
⎛
ILOAD(MAX) = ⎜IDRV − VBE
R BE
⎝
⎞
⎟ βMIN
⎠
where IDRV is the minimum guaranteed base drive current, VBE is the base-to-emitter voltage of the transistor,
and RBE is the pullup resistor connected between the
transistor’s base and emitter. Furthermore, the transistor’s current gain increases the linear regulator’s DC
loop gain (see the LDOA Stability Requirements section), so excessive gain destabilizes the output.
Therefore, transistors with current gain over 100 at the
maximum output current can be difficult to stabilize and
are not recommended. The transistor’s input capaci-
32
tance and input resistance also create a second pole,
which could be low enough to make the output unstable when heavily loaded.
The transistor’s saturation voltage at the maximum output current determines the minimum input-to-output
voltage differential that the linear regulator supports.
Alternatively, the package’s power dissipation could
limit the useable maximum input-to-output voltage differential. The maximum power dissipation capability of
the transistor’s package and mounting must exceed the
actual power dissipation in the device. The power dissipation equals the maximum load current times the maximum input-to-output differential:
PWR = ILOAD(MAX) (VINA -VOUTA)
PWR = ILOAD(MAX) VCE
LDOA Stability Requirements
The MAX8744/MAX8745 linear-regulator controller uses
an internal transconductance amplifier to drive an external pnp pass transistor. The transconductance amplifier,
the pass transistor, the base-to-emitter resistor, and the
output capacitor determine the loop stability.
The transconductance amplifier regulates the output
voltage by controlling the pass transistor’s base current. The total DC loop gain is approximately:
⎛ 5.5V ⎞ ⎛
IBIAShFE ⎞
A V(LDO) = ⎜
⎟ ⎜1 + I
⎟
V
⎝ T ⎠⎝
LOAD ⎠
where VT is 26mV at room temperature, hFE is the pass
transistor’s DC gain, and IBIAS is the current through
the base-to-emitter resistor (RBE). The 680Ω base-toemitter resistor used in Figure 1 was chosen to provide
a 1mA bias current (IBIAS).
______________________________________________________________________________________
High-Efficiency, Quad Output, Main PowerSupply Controllers for Notebook Computers
1) First, calculate the dominant pole set by the linear
regulator’s output capacitor and the load resistor:
fPOLE(LDO) =
1
2πCOUTARLOAD
where COUTA is the output capacitance of the auxiliary LDO and RLOAD is the load resistance corresponding to the maximum load current. The unitygain crossover of the linear regulator is:
fCROSSOVER = AV(LDO)fPOLE(LDO)
2) The pole caused by the internal amplifier delay is at
approximately 1MHz:
f POLE(AMP) ≈ 1MHz
3) Next, calculate the pole set by the transistor’s input
capacitance, the transistor’s input resistance, and
the base-to-emitter pullup resistor. Since the transistor’s input resistance (hFE/gm) is typically much
greater than the base-to-emitter pullup resistance,
the pole can be determined from the simplified
equation:
1
fPOLE(CIN) ≈
2πCINRIN
g
CIN = m
2πfT
where gm is the transconductance of the pass transistor, and fT is the transition frequency. Both parameters can be found in the transistor’s data sheet.
Therefore, the equation can be further reduced to:
f
f POLE(CIN) ≈ T
hFE
4) Next, calculate the pole set by the linear regulator’s
feedback resistance and the capacitance between
FBA and ground (approximately 5pF including
stray capacitance):
f POLE(FBA) =
1
2πCFBA (R5 || R6)
5) Next, calculate the zero caused by the output
capacitor’s ESR:
fZERO(ESR) =
1
2πCOUTARESR
where RESR is the equivalent series resistance of
COUTA.
6) To ensure stability, choose COUTA large enough so
that the crossover occurs well before the poles and
zero calculated in steps 2 through 5. The poles in
steps 3 and 4 generally occur at several MHz, and
using ceramic output capacitors ensures the ESR
zero occurs at several MHz as well. Placing the
crossover frequency below 500kHz is typically sufficient to avoid the amplifier delay pole and generally works well, unless unusual component
selection or extra capacitance moves the other
poles or zero below 1MHz.
A capacitor connected between the linear regulator’s output and the feedback node can improve
the transient response and reduce the noise coupled into the feedback loop.
If a low-dropout solution is required, an external pchannel MOSFET pass transistor could be used.
However, a pMOS-based linear regulator requires
higher output capacitance to stabilize the loop. The
high gate capacitance of the p-channel MOSFET
lowers the fPOLE(CIN) and can cause instability. A
large output capacitance must be used to reduce
the unity-gain bandwidth and ensure that the pole
is well above the unity-gain crossover frequency.
Applications Information
Duty-Cycle Limits
Minimum Input Voltage
The minimum input operating voltage (dropout voltage)
is restricted by the maximum duty-cycle specification
(see the Electrical Characteristics table). For the best
dropout performance, use the slowest switching frequency setting (200kHz, FSEL = GND). However, keep
in mind that the transient performance gets worse as
the step-down regulators approach the dropout voltage, so bulk output capacitance must be added (see
the voltage sag and soar equations in the SMPS Design
Procedure and Transient Response sections). The
absolute point of dropout occurs when the inductor current ramps down during the off-time (ΔIDOWN) as much
as it ramps up during the on-time (ΔIUP). This results in
a minimum operating voltage defined by the following
equation:
______________________________________________________________________________________
33
MAX8744/MAX8745
The output capacitor and the load resistance create the
dominant pole in the system. However, the internal amplifier delay, the pass transistor’s input capacitance, and the
stray capacitance at the feedback node create additional
poles in the system, and the output capacitor’s ESR generates a zero. For proper operation, use the following
steps to ensure the linear-regulator stability:
MAX8744/MAX8745
High-Efficiency, Quad Output, Main PowerSupply Controllers for Notebook Computers
⎛ 1
⎞
VIN(MIN) = VOUT + VCHG + h⎜
− 1⎟ (VOUT + VDIS )
⎝ DMAX
⎠
where VCHG and VDIS are the parasitic voltage drops in
the charge and discharge paths, respectively. A reasonable minimum value for h is 1.5, while the absolute
minimum input voltage is calculated with h = 1.
Maximum Input Voltage
The MAX8744/MAX8745 controllers include a minimum
on-time specification, which determines the maximum
input operating voltage that maintains the selected
switching frequency (see the Electrical Characteristics
table). Operation above this maximum input voltage
results in pulse-skipping operation, regardless of the
operating mode selected by SKIP. At the beginning of
each cycle, if the output voltage is still above the feedback threshold voltage, the controller does not trigger
an on-time pulse, effectively skipping a cycle. This
allows the controller to maintain regulation above the
maximum input voltage, but forces the controller to
effectively operate with a lower switching frequency.
This results in an input threshold voltage at which the
controller begins to skip pulses (VIN(SKIP)):
⎛
⎞
1
VIN(SKIP) = VOUT ⎜
⎟
⎝ fOSCt ON(MIN) ⎠
where fOSC is the switching frequency selected by FSEL.
PC Board Layout Guidelines
Careful PC board layout is critical to achieving low
switching losses and clean, stable operation. The
switching power stage requires particular attention
(Figure 9). If possible, mount all the power components
on the top side of the board, with their ground terminals
flush against one another. Follow these guidelines for
good PC board layout:
Keep the high-current paths short, especially at the
ground terminals. This practice is essential for stable,
jitter-free operation.
Keep the power traces and load connections short.
This practice is essential for high efficiency. Using thick
copper PC boards (2oz vs. 1oz) can enhance full-load
efficiency by 1% or more. Correctly routing PC board
34
traces is a difficult task that must be approached in
terms of fractions of centimeters, where a single milliohm of excess trace resistance causes a measurable
efficiency penalty.
Minimize current-sensing errors by connecting CSH_
and CSL_ directly across the current-sense resistor
(RSENSE_).
When trade-offs in trace lengths must be made, it is
preferable to allow the inductor charging path to be
made longer than the discharge path. For example, it is
better to allow some extra distance between the input
capacitors and the high-side MOSFET than to allow distance between the inductor and the low-side MOSFET
or between the inductor and the output filter capacitor.
Route high-speed switching nodes (BST_, LX_, DH_,
and DL_) away from sensitive analog areas (REF, FB_,
CSH_, CSL_).
Layout Procedure
Place the power components first, with ground terminals adjacent (N L _ source, C IN , C OUT _, and D L _
anode). If possible, make all these connections on the
top layer with wide, copper-filled areas.
Mount the controller IC adjacent to the low-side MOSFET,
preferably on the back side opposite NL_ and NH_ in
order to keep LX_, GND, DH_, and the DL_ gate-drive
lines short and wide. The DL_ and DH_ gate traces must
be short and wide (50 mils to 100 mils wide if the MOSFET
is 1in from the controller IC) to keep the driver impedance
low and for proper adaptive dead-time sensing.
Group the gate-drive components (BST_ diode and
capacitor, LDO5 bypass capacitor) together near the
controller IC.
Make the DC-DC controller ground connections as
shown in Figures 1 and 9. This diagram can be viewed
as having two separate ground planes: power ground,
where all the high-power components go, and an analog ground plane for sensitive analog components. The
analog ground plane and power ground plane must
meet only at a single point directly at the IC.
Connect the output power planes directly to the output
filter capacitor positive and negative terminals with multiple vias. Place the entire DC-DC converter circuit as
close to the load as is practical.
______________________________________________________________________________________
High-Efficiency, Quad Output, Main PowerSupply Controllers for Notebook Computers
MAX8744/MAX8745
MAX8744/MAX8745
CONNECT THE
EXPOSED PAD TO
ANALOG GND
VIA TO POWER
GROUND
CONNECT GND AND PGND TO THE
CONTROLLER AT ONE POINT
ONLY AS SHOWN
REF BYPASS
CAPACITOR
DUAL
n-CHANNEL
MOSFET
KELVIN SENSE VIAS
UNDER THE SENSE
RESISTOR
(REFER TO THE EVALUATION KIT)
SINGLE
n-CHANNEL
MOSFETS
INDUCTOR
INDUCTOR
DH
LX
DL
CIN
COUT
CIN
INPUT
COUT
INPUT
COUT
GROUND
OUTPUT
HIGH-POWER LAYOUT
OUTPUT
GROUND
LOW-POWER LAYOUT
Figure 9. PC Board Layout
Chip Information
TRANSISTOR COUNT: 6897
PROCESS: BiCMOS
______________________________________________________________________________________
35
Package Information
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information
go to www.maxim-ic.com/packages.)
QFN THIN.EPS
MAX8744/MAX8745
High-Efficiency, Quad Output, Main PowerSupply Controllers for Notebook Computers
PACKAGE OUTLINE,
16, 20, 28, 32, 40L THIN QFN, 5x5x0.8mm
21-0140
K
1
2
PACKAGE OUTLINE,
16, 20, 28, 32, 40L THIN QFN, 5x5x0.8mm
21-0140
K
2
2
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
36
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2006 Maxim Integrated Products
is a registered trademark of Maxim Integrated Products, Inc.