DM100E Series UltraMiniature, 1W SIP Single & Dual Output DC/DC Converters Electrical Specifications Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Key Features: Input • 1W Output Power • UltraMiniature SIP Case • Low 0.3 Inch Profile • Single & Dual Outputs • 1,000 VDC Isolation • >3.5 MHour MTBF • 12 Standard Models • LOWEST COST!! Parameter Input Voltage Range Conditions Min. Typ. Max. 5 VDC Input 4.5 5.0 5.5 12 VDC Input 10.8 12.0 13.2 Input Filter VDC Internal Capacitor Reverse Polarity Input Current 0.3 A Units Output Parameter Conditions Min. Typ. Max. ±1.0 ±3.0 % Dual Output , Balanced Loads ±0.1 ±1.0 % For Vin Change of 1% ±1.2 Output Voltage Accuracy Output Voltage Balance Line Regulation Load Regulation (Note 1) % See Model Selection Guide Ripple & Noise (20 MHz) (Note 2) Output Power Protection 50 75 mV P - P ±0.02 ±0.03 %/ºC Max. Units 120 Temperature Coefficient RoHS Compliant Units Output Short Circuit % Momentary (1.0 Sec.) General Parameter Conditions Isolation Voltage Isolation Resistance Isolation Capacitance Min. 60 Seconds 1,000 500 VDC 1,000 100 kHz, 1V Switching Frequency Typ. VDC MΩ 60 pF 100 kHz Environmental Min. Typ. Max. Units Operating Temperature Range Parameter Conditions Ambient -40 +25 +85 ºC Operating Temperature Range Case -40 +90 ºC -55 +125 ºC 95 % Storage Temperature Range Cooling MicroPower Direct 292 Page Street Suite D Stoughton, MA 02072 USA Humidity Free Air Convection RH, Non-condensing Physical Case Size 0.65 x 0.23 x 0.30 Inches (16.5 x 5.9 x 7.5 mm) Case Material Non-Conductive Black Plastic (UL94-V0) Weight T: (781) 344-8226 F: (781) 344-8481 E: [email protected] W: www.micropowerdirect.com 0.07 Oz (2.1g) Reliability Specifications Parameter MTBF Conditions Min. MIL HDBK 217F, 25ºC, Gnd Benign Typ. Max. 3.5 Units MHours Absolute Maximum Ratings Parameter Input Voltage Surge (1 Sec) Lead Temperature Internal Power Dissipation Conditions Min. Typ. Max. 5 VDC Input -0.7 9.0 12 VDC Input -0.7 18.0 Units VDC 1.5 mm From Case For 10 Sec 300 ºC All Models 450 mW Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. Model Selection Guide Model Number Input Voltage (VDC) Output Load Regulation Voltage Current Current No-Load (VDC) (mA, Max) (mA, Min) (%, Max) Current (mA) Efficiency (%, Typ) Fuse Rating Slow-Blow (mA) Nominal Range Full-Load DM101E 5 4.5 - 5.5 273 30 5.0 200.0 20.0 15 73 500 DM102E 5 4.5 - 5.5 270 30 12.0 83.0 9.0 15 74 500 DM103E 5 4.5 - 5.5 263 30 15.0 67.0 7.0 15 76 500 DM104E 5 4.5 - 5.5 278 30 ±5.0 ±100.0 ±10.0 15 72 500 DM105E 5 4.5 - 5.5 256 30 ±12.0 ±42.0 ±5.0 15 78 500 DM106E 5 4.5 - 5.5 256 30 ±15.0 ±33.0 ±4.0 15 78 500 DM111E 12 10.8 - 13.2 107 15 5.0 200.0 20.0 15 78 200 DM112E 12 10.8 - 13.2 103 15 12.0 83.0 9.0 15 81 200 DM113E 12 10.8 - 13.2 105 15 15.0 67.0 7.0 15 79 200 DM114E 12 10.8 - 13.2 114 15 ±5.0 ±100.0 ±10.0 15 73 200 DM115E 12 10.8 - 13.2 105 15 ±12.0 ±42.0 ±5.0 15 79 200 DM116E 12 10.8 - 13.2 105 15 ±15.0 ±33.0 ±4.0 15 79 200 Notes: 1. Output load regulation is specified for a load change of 10% to 100%. 2. These units should not be operated with a load under 10% of full load. Operation at no-load may cause damage to the unit. 3. These converters will operate without external components. However, when measuring output ripple, it is recommended that an external ceramic capacitor be placed from the +Vout pin to the -Vout pin for single output units and from each output to common for dual output units. An input capacitor will enhace stability over temperature and input line variations. Recommended capacitor values are given in Vin Input Capacitor 5 VDC 12 VDC 4.7 µF 2.2 µF Derating Curve Output Capacitor Single Dual 5 VDC 10.0 µF 4.7 µF 12 VDC 2.2 µF 1.0 µF 15 VDC 1.0 µF 0.47 µF Vout the table above. For applications requiring very low output noise levels, a simple LC filter should be effective. 4. Dual output units may be connected to provide a 10V, 24V or 30 VDC output. To do this, connect the load across the positive (+Vout) and negative (-Vout) outputs and float the output common 5. It is recommended that a fuse be used on the input of a power supply for protection. See the Model Selection table above for the correct rating. Mechanical Dimensions Pin Connections Pin Single Dual Pin Single Dual 1 2 4 +Vin -Vin -Vout +Vin -Vin -Vout 5 6 No Pin +Vout Common +Vout Notes: • All dimensions are typical in inches (mm) • Tolerance x.xx = ±0.01 (±0.25) • Pin 1 is marked by a “dot” or indentation on the side of the unit MicroPower Direct www.micropowerdirect.com 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: [email protected]