SEMICONDUCTOR TECHNICAL DATA The MC10E/100E241 is an 8-bit shiftable register. Unlike a standard universal shift register such as the E141, the E241 features internal data feedback organized so that the SHIFT control overrides the HOLD/LOAD control. This enables the normal operations of HOLD and LOAD to be toggled with a single control line without the need for external gating. It also enables switching to scan mode with the single SHIFT control line. The eight inputs D0 – D7 accept parallel input data, while S-IN accepts serial input data when in shift mode. Data is accepted a set-up time before the positive-going edge of CLK; shifting is also accomplished on the positive clock edge. A HIGH on the Master Reset pin (MR) asynchronously resets all the registers to zero. • • • • • • 8-BIT SCANNABLE REGISTER SHIFT overrides HOLD/LOAD Control 1000ps Max. CLK to Q Asynchronous Master Reset Pin-Compatible with E141 Extended 100E VEE Range of – 4.2V to – 5.46V 75kΩ Input Pulldown Resistors FN SUFFIX PLASTIC PACKAGE CASE 776-02 Pinout: 28-Lead PLCC (Top View) SEL0 NC D7 D6 D5 VCCO Q7 25 24 23 22 21 20 19 SEL1 26 18 Q6 CLK 27 17 Q5 MR 28 16 VCC VEE 1 15 NC S-IN 2 14 VCCO D0 3 13 Q4 D1 4 12 Q3 5 6 7 8 9 10 11 D2 D3 D4 VCCO Q0 Q1 Q2 LOGIC DIAGRAM S-IN D Q D0 R D Q D1 – D6 * All VCC and VCCO pins are tied together on the die. Q0 Q1 – Q6 R BITS 1–6 PIN NAMES Pin D0 – D7 S-IN SEL0 SEL1 CLK MR Q0 – Q7 Function D Q Parallel Date Inputs Serial Data Inputs SHIFT Control HOLD/LOAD Control Clock Master Reset Data Outputs D7 R HOLD/LOAD SHIFT CLK MR 7/96 Motorola, Inc. 1996 2–1 REV 3 Q7 MC10E241 MC100E241 DC CHARACTERISTICS (VEE = VEE(min) to VEE(max); VCC = VCCO = GND) 0°C Symbol Characteristic IIH Input HIGH Current IEE Power Supply Current 10E 100E min typ 25°C max min typ 150 85°C max min typ 150 max Unit 150 µA Condition MA 125 125 150 150 125 125 150 150 125 144 150 173 AC CHARACTERISTICS (VEE = VEE(min) to VEE(max); VCC = VCCO = GND) 0°C Symbol Characteristic min typ 25°C max min typ 700 900 625 600 750 725 85°C max min typ 700 900 625 600 750 725 fSHIFT Max. Shift Frequency 700 900 tPLH tPHL Propagation Delay to Output Clk MR 625 600 750 725 ts Setup Time D SEL0 (SHIFT) SEL1 (HOLD/LOAD) S-IN 175 350 400 125 25 200 250 –100 175 350 400 125 25 200 250 –100 175 350 400 125 25 200 250 –100 Hold Time D SEL0 (SHIFT) SEL1 (HOLD/LOAD) S-IN 200 100 50 300 – 25 – 200 – 250 100 200 100 50 300 – 25 – 200 – 250 100 200 100 50 300 – 25 – 200 – 250 100 tRR Reset Recovery Time 900 600 900 600 900 600 tPW Minimum Pulse Width Clk, MR 400 th tSKEW Within-Device Skew tr tf Rise/Fall Times 20 - 80% max Unit Condition MHz ps 975 975 975 975 975 975 ps ps ps ps 400 60 400 60 60 ps 1 ps 300 525 800 300 525 800 300 525 800 1. Within-device skew is defined as identical transitions on similar paths through a device. FUNCTION TABLE MR SEL0 SEL1 1 0 0 0 X 1 0 0 X X 1 0 MOTOROLA Function Outputs LOW Shift Data Hold Data Load Data 2–2 ECLinPS and ECLinPS Lite DL140 — Rev 4 MC10E241 MC100E241 OUTLINE DIMENSIONS FN SUFFIX PLASTIC PLCC PACKAGE CASE 776–02 ISSUE D 0.007 (0.180) B Y BRK -N- T L –M M U 0.007 (0.180) X G1 M S N T L –M S S N S D Z -L- -M- D W 28 V 1 C A 0.007 (0.180) M R 0.007 (0.180) M T L –M S T L –M S N S N S H S N S 0.007 (0.180) M T L –M N S S 0.004 (0.100) G J -T- K SEATING PLANE F VIEW S G1 T L –M S N 0.007 (0.180) M T L –M S N S VIEW S S NOTES: 1. DATUMS -L-, -M-, AND -N- DETERMINED WHERE TOP OF LEAD SHOULDER EXITS PLASTIC BODY AT MOLD PARTING LINE. 2. DIM G1, TRUE POSITION TO BE MEASURED AT DATUM -T-, SEATING PLANE. 3. DIM R AND U DO NOT INCLUDE MOLD FLASH. ALLOWABLE MOLD FLASH IS 0.010 (0.250) PER SIDE. 4. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 5. CONTROLLING DIMENSION: INCH. 6. THE PACKAGE TOP MAY BE SMALLER THAN THE PACKAGE BOTTOM BY UP TO 0.012 (0.300). DIMENSIONS R AND U ARE DETERMINED AT THE OUTERMOST EXTREMES OF THE PLASTIC BODY EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS, GATE BURRS AND INTERLEAD FLASH, BUT INCLUDING ANY MISMATCH BETWEEN THE TOP AND BOTTOM OF THE PLASTIC BODY. 7. DIMENSION H DOES NOT INCLUDE DAMBAR PROTRUSION OR INTRUSION. THE DAMBAR PROTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE GREATER THAN 0.037 (0.940). THE DAMBAR INTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE SMALLER THAN 0.025 (0.635). ECLinPS and ECLinPS Lite DL140 — Rev 4 T L –M K1 E S S VIEW D-D Z 0.010 (0.250) 0.010 (0.250) 2–3 DIM A B C E F G H J K R U V W X Y Z G1 K1 INCHES MIN MAX 0.485 0.495 0.485 0.495 0.165 0.180 0.090 0.110 0.013 0.019 0.050 BSC 0.026 0.032 0.020 — 0.025 — 0.450 0.456 0.450 0.456 0.042 0.048 0.042 0.048 0.042 0.056 — 0.020 2° 10° 0.410 0.430 0.040 — MILLIMETERS MIN MAX 12.32 12.57 12.32 12.57 4.20 4.57 2.29 2.79 0.33 0.48 1.27 BSC 0.66 0.81 0.51 — 0.64 — 11.43 11.58 11.43 11.58 1.07 1.21 1.07 1.21 1.07 1.42 — 0.50 2° 10° 10.42 10.92 1.02 — MOTOROLA MC10E241 MC100E241 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA/EUROPE/Locations Not Listed: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 or 602–303–5454 JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center, 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–81–3521–8315 MFAX: [email protected] – TOUCHTONE 602–244–6609 INTERNET: http://Design–NET.com ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298 ◊ MOTOROLA 2–4 *MC10E241/D* MC10E241/D ECLinPS and ECLinPS Lite DL140 — Rev 4