0RODUCT$ATA3HEET Contact Factory for Replacement Model 7!44 ! !#$#0 /7%23500,9 .8 $%3#2)04)/. 4HE.8ISACOMPACTWATT0OWER&ACTOR#ORRECTEDMULTIPLE OUTPUTPOWERSUPPLY!LLOUTPUTSAREFULLYISOLATEDANDREGULATED !CTIVECURRENTSHARINGCIRCUITRYTOGETHERWITHCONTROLFUNCTIONS ANDALARMOPTIONSSIMPLIFIES.ANDREDUNDANTAPPLICATIONS &ANANDDISKDRIVEAPPLICATIONSAREHANDLEDBYTHEPEAKCURRENT RATINGSOFTHEAUXILIARYOUTPUTS &%!452%3 !CTIVE0OWER&ACTOR#ORRECTION &ULLY)SOLATED/UTPUTS ,OW0ROFILEvXvXv /NE4WO4HREEAND&OUR/UTPUT-ODELS !'%.#9!002/6!,3 .#URRENT3HARING &##6$%#LASS"%-)&ILTER3TANDARD /PTIONAL&AN-OUNTED/N#OVER )NTERNETHTTPWWWCDPOWERELECTRONICSCOM 0OWER%LECTRONICS$IVISION5NITED3TATES %"RITANNIA$RIVE4UCSON!RIZONA 0HONE&AX .82%6" 0OWER%LECTRONICS$IVISION%UROPE #$4ECHNOLOGIES0OWER%LECTRONICS,TD 3HANNON)NDUSTRIAL%STATE 3HANNON#O#LARE)RELAND 4EL &AX 0AGE Input Specifications Parameter Operating Range Conditions Min 47-63 Hz Typ 90 Max Units 264 VAC Inrush Current Limiting 120VAC, cold start 37 APK 240VAC cold start 70 APK Efficiency 120V, full load 240V, full load Power Factor Correction (PFC) 70 % 75 % 0.99 Meets IEC 1000-4-7/EN61000-3-2 (formerly IEC 555-2) Remote Sense Remote Sense is provided on Output #1 and will compensate for 0.7V of line drop. Remote Sense leads are protected against open, short and reversal. Remote On/Of The power supply is turned on with a TTL logic ‘1’ (or open) signal and turned off by a switch closure or TTL logic ‘0’ referenced to (-) sense terminal. Consult the factory for other options. Over Voltage Protection Output #1: 6.5V ± 0.5 VDC. The power supply will latch off until AC power is cycled. Over Current Protection Individual current limit on all outputs. Automatic recovery upon fault removal. Transient Response The peak output voltage excursion will not exceed 2% and will recover within 1% in 200 μsec for a 25% load step change. Power Fail Signal Upon AC input voltage removal, the power fail signal drops to logic zero at least 5msec before loss of DC output. On AC input turn-on, signal remains low until outputs are in regulation. Consult the factory for other options. N+1 Load Share Output #1 has active load sharing circuitry. Units will load share within 1.5% of Maximum Rated Load. Over Temperature Protection Thermal switch turns off power supply if overheating occurs and automatically restarts. Safety UL Recognized: UL File Number E14675 (1950 & 1012) CSA Certified: CSA File Number LR 9070-154C (C22.2 No. 234-M90, Level 6) TUV License Number: R9576031 (EN60950) (IEC950) Cooling The unit is designed to operate with 30 CFM of airflow. Output Isolation All outputs are fully isolated. Page 2 NX350 3/98 REV B Output Voltages and Maximum Rated Loads OUTPUT #1 IMAX VOUT OUTPUT #2 VNOM IMAX/IPK OUTPUT #3 VNOM IMAX/IPK NX350-U3A ± 5V 50A ± 12V 10A/12A ± 12V 8A/10A - - NX350-U3B ± 5V 50A ± 15V 10A/12A ± 15V 8A/10A - - NX350-U4C ± 5V 50A ± 12V 10A/12A ± 12V 8A/10A ± 5V 3.0A/4.0A NX350-U4D ± 5V 50A ± 12V 10A/12A ± 12V 8A/10A ± 24V 1.5A/2.0A NX350-U4E ± 5V 50A ± 12V 10A/12A ± 12V 8A/10A ± 12V 3.0A/4.0A NX350-U4F ± 5V 50A ± 15V 10A/12A ± 15V 8A/10A ± 5V NX350-U4G ± 5V 50A ± 15V 10A/12A ± 15V 8A/10A ± 24V 1.5A/2.0A NX350-U4H ± 5V 50A ± 15V 10A/12A ± 15V 8A/10A ± 12V 3.0A/4.0A MODEL NUMBER OUTPUT #4 VNOM IMAX/IPK 3.0A/4.0A Note: Peak current ratings are for 10sec maximum. Total power not to exceed 350 watts. Output Specifications Parameter Limits Regulation Line ± 0.03% Load ±0.25% Cross ±0.05% Minimum Load Output #1 3.0A Auxiliary Outputs 0.1A Hold-Up Time 20mSec at Full Load Parameter Conditions Voltage Adustment Range Nominal line on all outputs PARD Min Typ Max ±5 Peak-to-peak 20 MHz bandwidth Units % 1 % 50 °C 70 °C +85 °C Temperature Operating 0 Derates to half power Storage Temperature Coefficient (TC) NX350 3/98 REV B -20 After half hour warm-up ± 0.02 %/°C Page 3 Mechanical TOP VIEW 0.040 1.95 8.50 0.25 COVER 0.55 1 TB2 3.90 4.85 1 J9 OUTPUT NO. 1 1 5v RETURN 9.00 TB1 6-32 THD 4 PLC’S Maximum depth of mounting screws is 0.156 inches 5v NOTES: All measurements are in inches FAN MOUNTED ON COVER WILL ADD 1.30”. COOLING: The NX350 is designed to operate with 30 CM airflow. SHOCK AND VIBRATION: The NX350 meets the requirements of MIL STD-810D. (Vibration-Method 514.3 Procedure I; Shock-Method 516.3 Procedure I.) WEIGHT: Approximately 3 lbs. Terminal Block 1 POS FUNCTION J9 Connector Terminal Block 2 POS FUNCTION PIN FUNCTION 1 AC Line 1 -V2 1 + Sense 2 AC Neutral 2 +V2 2 - Sense 3 Ground 3 -V3 3 N/C 4 +V3 4 N/C 5 -V4 5 Start Up Sync. 6 +V4 6 Power Fail 7 Remote Inhibit 8 Current Share 9 Cntl Signal Rtn J9 Connector Molex No. Connector 22-28-1090 Standard Options are shown, consult factory for other available options. The information provided herein is believed to be reliable; however, C&D Technologies assumes no responsibility for inaccuracies or omissions. C&D Technologies assumes no responsibility for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specifications are subject to change without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. C&D Technologies does not authorize or warrant any C&D Technologies product for use in life support devices/systems or in aircraft control applications. Page 4 NX350 3/98 REV B