S102T02 Series S202T02 Series IT(rms)≤2A, Zero Cross type Low profile SIP 4pin Triac output SSR S102T02 Series S202T02 Series ∗ Non-zero cross type is also available. (S102T01 Series/ S202T01 Series) ■ Description ■ Agency approvals/Compliance S102T02 Series and S202T02 Series Solid State Relays (SSR) are an integration of an infrared emitting diode (IRED), a Phototriac Detector and a main output Triac. These devices are ideally suited for controlling high voltage AC loads with solid state reliability while providing 3.0kV isolation (Viso(rms)) from input to output. 1. Recognized by UL508, file No. E94758 (as models No. S102T02/S202T02) 2. Approved by CSA 22.2 No.14, file No. LR63705 (as models No. S102T02/S202T02) 3. Package resin : UL flammability grade (94V-0) ■ Applications 1. Isolated interface between high voltage AC devices and lower voltage DC control circuitry. 2. Switching motors, fans, heaters, solenoids, and valves. 3. Power control in applications such as lighting and temperature control equipment. ■ Features 1. Output current, IT(rms)≤2.0A 2. Zero crossing functionary (VOX : MAX. 35V) 3. Slim 4 pin low profile SIP package 4. High repetitive peak off-state voltage (VDRM : 600V, S202T02 Series) (VDRM : 400V, S102T02 Series) 5. High isolation voltage between input and output (Viso(rms) : 3.0kV) 6. Lead-free terminal components are also available (see Model Line-up section in this datasheet) 7. Screw hole for heat sink Notice The content of data sheet is subject to change without prior notice. In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. 1 Sheet No.:D4-A01601EN Date Apr. 28. 2004 © SHARP Corporation S102T02 Series S202T02 Series ■ Internal Connection Diagram 1 2 3 4 1 2 Output (Triac T1) Output (Triac T2) Input (+) Input (−) 3 4 Zero Crossing Circuit ■ Outline Dimensions (Unit : mm) Common to pin No.2 1 2 1.8±0.3 0.4±0.1 (1.8) 3 4 1.6±0.2 1 2 (3.5) 1.8±0.3 (5.08) Product mass : approx. 3.5g Date code (2 digit) 3-1.2±0.2 3-1.4±0.2 4-0.8±0.2 0.4±0.1 (1.8) 3 4 (2.54) (3.8) (2.54) (10.16) + − 10±0.2 2A265VAC ~ ∗ 3.8MIN. 4-0.8±0.2 S202T02 6.2 Date code (2 digit) 3-1.2±0.2 3-1.4±0.2 3±0.2 Common to pin No.2 UL mark CSA mark Epoxy resin MIN. (3.5) (3.8) (5.08) + − (0.8) 3.8MIN. 6.2 1.6±0.2 0.2MIN. 2A125VAC ~ ∗ (25.8) S102T02 10±0.2 11.5±0.2 UL mark CSA mark Epoxy resin 6.4±0.2 φ3.7±0.2 (0.8) Common to pin No.2 0.2MIN. 3±0.2 4.5±0.3 6.4±0.2 φ3.7±0.2 MIN. (25.8) 4.5±0.3 Common to pin No.2 4±0.2 7±0.2 11.5±0.2 7 23±0.2 4±0.2 ±0.2 1.8±0.2 23±0.2 1.8±0.2 S202T02 S102T02 (10.16) Product mass : approx. 3.5g ∗ : Do not allow external connection. ( ) : Typical dimensions Sheet No.: D4-A01601EN 2 S102T02 Series S202T02 Series Date code (2 digit) A.D. 1990 1991 1992 1993 1994 1995 1996 1997 1998 1999 2000 2001 1st digit Year of production A.D Mark 2002 A 2003 B 2004 C 2005 D 2006 E 2007 F 2008 H 2009 J 2010 K 2011 L 2012 M ·· N · Mark P R S T U V W X A B C ·· · 2nd digit Month of production Month Mark January 1 February 2 March 3 April 4 May 5 June 6 July 7 August 8 September 9 October O November N December D repeats in a 20 year cycle Country of origin Japan Rank mark There is no rank mark indicator and currently there are no rank offered for this device. Sheet No.: D4-A01601EN 3 S102T02 Series S202T02 Series (Ta=25˚C) Parameter Symbol Rating Unit *3 Forward current IF 50 mA Input Reverse voltage VR 6 V RMS ON-state current IT (rms) 2 *3 A *4 Peak one cycle surge current Isurge 20 A Repetitive S102T02 400 VDRM V peak OFF-state voltage S202T02 600 Output Non-Repetitive S102T02 400 VDSM V peak OFF-state voltage S202T02 600 Critical rate of rise of ON-state current dIT/dt 40 A/µs Operating frequency 45 to 65 f Hz *1 Isolation voltage 3.0 Viso(rms) kV Operating temperature Topr −25 to +100 ˚C Storage temperature Tstg −30 to +125 ˚C *2 Soldering temperature Tsol 260 ˚C 1.5mm ■ Absolute Maximum Ratings Soldering area *1 40 to 60%RH, AC for 1minute, f=60Hz *2 For 10s *3 Refer to Fig.1, Fig.2 *4 f=60Hz sine wave, Tj=25˚C start ■ Electro-optical Characteristics (Ta=25˚C) Parameter Symbol Conditions MIN. − VF IF=20mA Forward voltage Input − IR VR=3V Reverse current IDRM − VD=VDRM Repetitive peak OFF-state current V (rms) I (rms)=2A, Resistance load, I =20mA − ON-state voltage T T F IH − − Output Holding current dV/dt VD=2/3•VDRM 30 Critical rate of rise of OFF-state voltage Critical rate of rise of OFF-state voltage at commutaion (dV/dt)c Tj=125˚C, VD=2/3•VDRM, dIT/dt=−1.0A/ms 4 IFT VD=6V, RL=30Ω Minimum trigger current − VOX IF=8mA Zero cross voltage − RISO DC500V, 40 to 60%RH Isolation resistance 1010 VD(rms)=100V, AC50Hz, IF=20mA − S102T02 IT(rms)=2A, Resistance load Transfer Turn-on time ton VD(rms)=200V, AC50Hz, IF=20mA charac− S202T02 teristics IT(rms)=2A, Resistance load VD(rms)=100V, AC50Hz, IF=20mA − S102T02 IT(rms)=2A, Resistance load toff Turn-off time VD(rms)=200V, AC50Hz, IF=20mA − S202T02 IT(rms)=2A, Resistance load TYP. 1.2 − − − − − − − − − MAX. 1.4 100 100 1.7 25 − − 8 35 − − 10 Unit V µA µA V mA V/µs V/µs mA V Ω ms − 10 − 10 − 10 ms Sheet No.: D4-A01601EN 4 S102T02 Series S202T02 Series ■ Model Line-up (1) (Lead-free terminal components) 25pcs/sleeve VDRM [V] IFT[mA] (VD=6V, RL=30Ω) S102T02F S202T02F 400 600 MAX.8 MAX.8 Sleeve Shipping Package Model No. ■ Model Line-up (2) (Lead solder plating components) 25pcs/sleeve VDRM [V] IFT[mA] (VD=6V, RL=30Ω) S102T02 S202T02 400 600 MAX.8 MAX.8 Sleeve Shipping Package Model No. Please contact a local SHARP sales representative to see the actual status of the production. Sheet No.: D4-A01601EN 5 S102T02 Series S202T02 Series Fig.2 RMS ON-state Current vs. Ambient Temperature 60 3.0 50 2.5 RMS ON-state current IT(rms) (A) Forward current IF (mA) Fig.1 Forward Current vs. Ambient Temperature 40 30 20 10 0 −25 0 25 50 75 100 2.0 1.5 1.0 0.5 0 −25 125 0 40 50 75 100 125 Ambient temperature Ta (˚C) Ambient temperature Ta (˚C) Fig.3 Forward Current vs. Forward Voltage Fig.4 Surge Current vs. Power-on Cycle 25 100 f=60Hz Tj=25˚C start 20 Ta=75˚C 50˚C Surge current Isurge (A) Forward current IF (mA) 25 10 25˚C 0˚C −25˚C 1 15 10 5 0.1 0.6 0 0.8 1.0 1.2 1.4 1.6 1 1.8 10 Forward voltage VF (mA) Power-on cycle (Times) Fig.5 Minimum Trigger Current vs. Ambient Temperature Fig.6 Maximum ON-state Power Dissipation vs. RMS ON-state Current 2.5 Maximum ON-state power dissipation (W) 10 Minimum trigger current IFT (mA) VD=6V 8 6 4 2 0 −25 100 Ta=25˚C 2 1.5 1 0.5 0 0 25 50 75 0 100 0.5 1 1.5 2 RMS ON-state current IT (rms)(A) Ambient temperature Ta (˚C) Sheet No.: D4-A01601EN 6 S102T02 Series S202T02 Series Fig.7-a Repetitive Peak OFF-state Current vs. Ambient Temperature (S102T02) Fig.7-b Repetitive Peak OFF-state Current vs. Ambient Temperature (S202T02) 10−3 10−3 VD=600V Repetitive peak OFF-state current IDRM (A) Repetitive peak OFF-state current IDRM (A) VD=400V 10−4 10−5 10−6 10−7 10−8 10−9 −25 0 25 50 75 10−4 10−5 10−6 10−7 10−8 10−9 −25 100 0 25 50 75 100 Ambient temperature Ta (˚C) Ambient temperature Ta (˚C) Remarks : Please be aware that all data in the graph are just for reference. Sheet No.: D4-A01601EN 7 S102T02 Series S202T02 Series ■ Design Considerations ● Recommended Operating Conditions Input Output Symbol Parameter Input signal current at ON state IF(ON) Input signal current at OFF state IF(OFF) S102T02 Load supply voltage VOUT(rms) S202T02 Load supply current Frequency Operating temperature IOUT(rms) f Topr Conditions − − − Locate snubber circuit between output terminals (Cs=0.022µF, Rs=47Ω) − − MIN. 16 0 80 80 0.1 47 −20 MAX. 24 0.1 120 240 IT(rms) ×80%(∗) 63 80 Unit mA mA V mA Hz ˚C (∗) See Fig.2 about derating curve (IT(rms) vs. ambient temperature). ● Design guide In order for the SSR to turn off, the triggering current (lF) must be 0.1mA or less. When the input current (IF) is below 0.1mA, the output Triac will be in the open circuit mode. However, if the voltage across the Triac, VD, increases faster than rated dV/dt, the Triac may turn on. To avoid this situation, please incorporate a snubber circuit. Due to the many different types of load that can be driven, we can merely recommend some circuit vales to start with : Cs=0.022µF and Rs=47Ω. The operation of the SSR and snubber circuit should be tested and if unintentional switching occurs, please adjust the snubber circuit component values accordingly. When making the transition from On to Off state, a snubber circuit should be used ensure that sudden drops in current are not accompanied by large instantaneous changes in voltage across the Triac. This fast change in voltage is brought about by the phase difference between current and voltage. Primarily, this is experienced in driving loads which are inductive such as motors and solenoids. Following the procedure outlined above should provide sufficient results. For over voltage protection, a Varistor may be used. Any snubber or Varistor used for the above mentioned scenarios should be located as close to the main output triac as possible. Particular attention needs to be paid when utilizing SSRs that incorporate zero crossing circuitry. If the phase difference between the voltage and the current at the output pins is large enough, zero crossing type SSRs cannot be used. The result, if zero crossing SSRs are used under this condition, is that the SSR may not turn on and off irregardless of the input current. In this case, only a non zero cross type SSR should be used in combination with the above mentioned snubber circuit selection process. The load current should be within the bounds of derating curve. (Refer to Fig.2) Also, please use the optional heat sink when necessary. In case the optional heat sink is used and the isolation voltage between the device and the optional heat sink is needed, please locate the insulation sheet between the device and the heat sink. When the optional heat sink is equipped, please set up the M3 screw-fastening torque at 0.3 to 0.5N•m. In order to dissipate the heat generated from the inside of device effectively, please follow the below suggestions. Sheet No.: D4-A01601EN 8 S102T02 Series S202T02 Series (a) Make sure there are no warps or bumps on the heat sink, insulation sheet and device surface. (b) Make sure there are no metal dusts or burrs attached onto the heat sink, insulation sheet and device surface. (c) Make sure silicone grease is evenly spread out on the heat sink, insulation sheet and device surface. Silicone grease to be used is as follows; 1) There is no aged deterioration within the operating temperature ranges. 2) Base oil of grease is hardly separated and is hardly permeated in the device. 3) Even if base oil is separated and permeated in the device, it should not degrade the function of a device. Recommended grease : G-746 (Shin-Etsu Chemical Co., Ltd.) : G-747 (Shin-Etsu Chemical Co., Ltd.) : SC102 (Dow Corning Toray Silicone Co., Ltd.) In case the optional heat sink is screwed up, please solder after screwed. In case of the lead frame bending, please keep the following minimum distance and avoid any mechanical stress between the base of terminals and the molding resin. 3.8mm MIN. Some of AC electromagnetic counters or solenoids have built-in rectifier such as the diode. In this case, please use the device carefully since the load current waveform becomes similar with rectangular waveform and this results may not make a device turn off. ● Degradation In general, the emission of the IRED used in SSR will degrade over time. In the case where long term operation and / or constant extreme temperature fluctuations will be applied to the devices, please allow for a worst case scenario of 50% degradation over 5years. Therefore in order to maintain proper operation, a design implementing these SSRs should provide at least twice the minimum required triggering current from initial operation. ● Standard Circuit S102T02 S202T02 R1 +VCC 3 SSR D1 4 V1 Load 2 ZS AC Line 1 Tr1 ZS : Surge absorption circuit (Snubber circuit) ✩ For additional design assistance, please review our corresponding Optoelectronic Application Notes. Sheet No.: D4-A01601EN 9 S102T02 Series S202T02 Series ■ Manufacturing Guidelines ● Soldering Method Flow Soldering (No solder bathing) Flow soldering should be completed below 260˚C and within 10s. Preheating is within the bounds of 100 to 150˚C and 30 to 80s. Please solder within one time. Other notices Please test the soldering method in actual condition and make sure the soldering works fine, since the impact on the junction between the device and PCB varies depending on the tooling and soldering conditions. Sheet No.: D4-A01601EN 10 S102T02 Series S202T02 Series ● Cleaning instructions Solvent cleaning : Solvent temperature should be 45˚C or below. Immersion time should be 3minutes or less. Ultrasonic cleaning : The impact on the device varies depending on the size of the cleaning bath, ultrasonic output, cleaning time, size of PCB and mounting method of the device. Therefore, please make sure the device withstands the ultrasonic cleaning in actual conditions in advance of mass production. Recommended solvent materials : Ethyl alcohol, Methyl alcohol and Isopropyl alcohol. In case the other type of solvent materials are intended to be used, please make sure they work fine in actual using conditions since some materials may erode the packaging resin. ● Presence of ODC This product shall not contain the following materials. And they are not used in the production process for this device. Regulation substances : CFCs, Halon, Carbon tetrachloride, 1.1.1-Trichloroethane (Methylchloroform) Specific brominated flame retardants such as the PBBOs and PBBs are not used in this product at all. Sheet No.: D4-A01601EN 11 S102T02 Series S202T02 Series ■ Package specification ● Sleeve package Package materials Sleeve : HIPS Stopper : Olefine-Elastomer Package method MAX. 25pcs of products shall be packaged in a sleeve. Both ends shall be closed by stoppers. MAX. 20 sleeves in one case. ±2 17.8 620 10.6 1.1 1.1 (30.0) 12.0 Sleeve outline dimensions 4.7 7.6 (8.5) (Unit : mm) Sheet No.: D4-A01601EN 12 S102T02 Series S202T02 Series ■ Important Notices with equipment that requires higher reliability such as: --- Transportation control and safety equipment (i.e., aircraft, trains, automobiles, etc.) --- Traffic signals --- Gas leakage sensor breakers --- Alarm equipment --- Various safety devices, etc. (iii) SHARP devices shall not be used for or in connection with equipment that requires an extremely high level of reliability and safety such as: --- Space applications --- Telecommunication equipment [trunk lines] --- Nuclear power control equipment --- Medical and other life support equipment (e.g., scuba). · The circuit application examples in this publication are provided to explain representative applications of SHARP devices and are not intended to guarantee any circuit design or license any intellectual property rights. SHARP takes no responsibility for any problems related to any intellectual property right of a third party resulting from the use of SHARP's devices. · Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. SHARP reserves the right to make changes in the specifications, characteristics, data, materials, structure, and other contents described herein at any time without notice in order to improve design or reliability. Manufacturing locations are also subject to change without notice. · If the SHARP devices listed in this publication fall within the scope of strategic products described in the Foreign Exchange and Foreign Trade Law of Japan, it is necessary to obtain approval to export such SHARP devices. · Observe the following points when using any devices in this publication. SHARP takes no responsibility for damage caused by improper use of the devices which does not meet the conditions and absolute maximum ratings to be used specified in the relevant specification sheet nor meet the following conditions: (i) The devices in this publication are designed for use in general electronic equipment designs such as: --- Personal computers --- Office automation equipment --- Telecommunication equipment [terminal] --- Test and measurement equipment --- Industrial control --- Audio visual equipment --- Consumer electronics (ii) Measures such as fail-safe function and redundant design should be taken to ensure reliability and safety when SHARP devices are used for or in connection · This publication is the proprietary product of SHARP and is copyrighted, with all rights reserved. Under the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP. Express written permission is also required before any use of this publication may be made by a third party. · Contact and consult with a SHARP representative if there are any questions about the contents of this publication. Sheet No.: D4-A01601EN 13