CYPRESS STK12C68

STK12C68-5 (SMD5962-94599)
64 Kbit (8K x 8) AutoStore nvSRAM
Features
Functional Description
■
35 ns and 55 ns access times
■
Hands off automatic STORE on power down with external
68 µF capacitor
■
STORE to QuantumTrap™ nonvolatile elements is initiated
by software, hardware, or AutoStore™ on power down
■
RECALL to SRAM initiated by software or power up
■
Unlimited Read, Write, and Recall cycles
■
1,000,000 STORE cycles to QuantumTrap
■
100 year data retention to QuantumTrap
The Cypress STK12C68-5 is a fast static RAM with a nonvolatile element in each memory cell. The embedded nonvolatile
elements incorporate QuantumTrap technology producing the
world’s most reliable nonvolatile memory. The SRAM provides
unlimited read and write cycles, while independent nonvolatile
data resides in the highly reliable QuantumTrap cell. Data
transfers from the SRAM to the nonvolatile elements (the
STORE operation) takes place automatically at power down.
On power up, data is restored to the SRAM (the RECALL
operation) from the nonvolatile memory. Both the STORE and
RECALL operations are also available under software control.
A hardware STORE is initiated with the HSB pin.
■
Single 5V+10% operation
■
Military temperature
■
28-pin (300mil) CDIP and 28-pad LCC packages
Logic Block Diagram
Quantum Trap
128 X 512
A5
STORE
ROW DECODER
A6
A7
A8
A9
A 11
STATIC RAM
ARRAY
128 X 512
RECALL
VCC
VCAP
POWER
CONTROL
STORE/
RECALL
CONTROL
HSB
SOFTWARE
DETECT
A 12
DQ 0
A0
- A12
COLUMN I/O
INPUT BUFFERS
DQ 1
DQ 2
DQ 3
DQ 4
DQ 5
DQ 6
COLUMN DEC
A 0 A 1 A 2 A 3 A 4 A 10
DQ 7
OE
CE
WE
Cypress Semiconductor Corporation
Document Number: 001-51026 Rev. **
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised March 02, 2009
[+] Feedback
STK12C68-5 (SMD5962-94599)
Pinouts
Figure 1. Pin Diagram - 28-Pin DIP
Figure 2. Pin Diagram - 28-Pin LLC
Pin Definitions
Pin Name
Alt
A0–A12
IO Type
Input
DQ0-DQ7
Description
Address Inputs. Used to select one of the 8,192 bytes of the nvSRAM.
Input or Output Bidirectional Data IO Lines. Used as input or output lines depending on operation.
WE
W
Input
Write Enable Input, Active LOW. When the chip is enabled and WE is LOW, data on the IO
pins is written to the specific address location.
CE
E
Input
Chip Enable Input, Active LOW. When LOW, selects the chip. When HIGH, deselects the
chip.
OE
G
Input
Output Enable, Active LOW. The active LOW OE input enables the data output buffers during
read cycles. Deasserting OE HIGH causes the IO pins to tri-state.
VSS
Ground
Ground for the Device. The device is connected to ground of the system.
VCC
Power Supply Power Supply Inputs to the Device.
HSB
Input or Output Hardware Store Busy (HSB). When LOW, this output indicates a Hardware Store is in
progress. When pulled low external to the chip, it initiates a nonvolatile STORE operation. A
weak internal pull up resistor keeps this pin high if not connected (connection optional).
VCAP
Power Supply AutoStore Capacitor. Supplies power to nvSRAM during power loss to store data from SRAM
to nonvolatile elements.
Document Number: 001-51026 Rev. **
Page 2 of 18
[+] Feedback
STK12C68-5 (SMD5962-94599)
Device Operation
The STK12C68-5 nvSRAM is made up of two functional components paired in the same physical cell. These are an SRAM
memory cell and a nonvolatile QuantumTrap cell. The SRAM
memory cell operates as a standard fast static RAM. Data in the
SRAM is transferred to the nonvolatile cell (the STORE
operation) or from the nonvolatile cell to SRAM (the RECALL
operation). This unique architecture enables the storage and
recall of all cells in parallel. During the STORE and RECALL
operations, SRAM Read and Write operations are inhibited. The
STK12C68-5 supports unlimited reads and writes similar to a
typical SRAM. In addition, it provides unlimited RECALL operations from the nonvolatile cells and up to one million STORE
operations.
During normal operation, the device draws current from VCC to
charge a capacitor connected to the VCAP pin. This stored
charge is used by the chip to perform a single STORE operation.
If the voltage on the VCC pin drops below VSWITCH, the part
automatically disconnects the VCAP pin from VCC. A STORE
operation is initiated with power provided by the VCAP capacitor.
Figure 3 shows the proper connection of the storage capacitor
(VCAP) for automatic store operation. A charge storage capacitor
between 68 µF and 220 µF (+20%) rated at 6V must be provided.
The voltage on the VCAP pin is driven to 5V by a charge pump
internal to the chip. A pull up is placed on WE to hold it inactive
during power up.
Figure 3. AutoStore Mode
9FF
:(
N2KP
9&$3
5)
%\SDVV
+6%
5)
Y
The STK12C68-5 performs a Read cycle whenever CE and OE
are LOW while WE and HSB are HIGH. The address specified
on pins A0–12 determines the 8,192 data bytes accessed. When
the Read is initiated by an address transition, the outputs are
valid after a delay of tAA (Read cycle 1). If the Read is initiated
by CE or OE, the outputs are valid at tACE or at tDOE, whichever
is later (Read cycle 2). The data outputs repeatedly respond to
address changes within the tAA access time without the need for
transitions on any control input pins, and remains valid until
another address change or until CE or OE is brought HIGH, or
WE or HSB is brought LOW.
N2KP
SRAM Read
SRAM Write
A Write cycle is performed whenever CE and WE are LOW and
HSB is HIGH. The address inputs must be stable prior to entering
the Write cycle and must remain stable until either CE or WE
goes HIGH at the end of the cycle. The data on the common IO
pins DQ0–7 are written into the memory if it has valid tSD, before
the end of a WE controlled Write or before the end of an CE
controlled Write. Keep OE HIGH during the entire Write cycle to
avoid data bus contention on common IO lines. If OE is left LOW,
internal circuitry turns off the output buffers tHZWE after WE goes
LOW.
AutoStore Operation
The STK12C68-5 stores data to nvSRAM using one of three
storage operations:
1. Hardware store activated by HSB
2. Software store activated by an address sequence
3. AutoStore on device power down
AutoStore operation is a unique feature of QuantumTrap
technology and is enabled by default on the STK12C68-5.
Document Number: 001-51026 Rev. **
9VV
In system power mode, both VCC and VCAP are connected to the
+5V power supply without the 68 μF capacitor. In this mode, the
AutoStore function of the STK12C68-5 operates on the stored
system charge as power goes down. The user must, however,
guarantee that VCC does not drop below 3.6V during the 10 ms
STORE cycle.
To reduce unnecessary nonvolatile stores, AutoStore, and
Hardware Store operations are ignored, unless at least one Write
operation has taken place since the most recent STORE or
RECALL cycle. Software initiated STORE cycles are performed
regardless of whether a Write operation has taken place. An
optional pull up resistor is shown connected to HSB. The HSB
signal is monitored by the system to detect if an AutoStore cycle
is in progress.
Page 3 of 18
[+] Feedback
STK12C68-5 (SMD5962-94599)
9FF
:(
N2KP
9&$3
N2KP
5)
%\SDVV
Figure 4. AutoStore Inhibit Mode
+6%
During any STORE operation, regardless of how it is initiated,
the STK12C68-5 continues to drive the HSB pin LOW,
releasing it only when the STORE is complete. After
completing the STORE operation, the STK12C68-5 remains
disabled until the HSB pin returns HIGH.
If HSB is not used, it is left unconnected.
Hardware RECALL (Power Up)
During power up or after any low power condition (VCC <
VRESET), an internal RECALL request is latched. When VCC
once again exceeds the sense voltage of VSWITCH, a RECALL
cycle is automatically initiated and takes tHRECALL to complete.
If the STK12C68-5 is in a Write state at the end of power up
RECALL, the SRAM data is corrupted. To help avoid this
situation, a 10 Kohm resistor is connected either between WE
and system VCC or between CE and system VCC.
Software STORE
9VV
If the power supply drops faster than 20 us/volt before Vcc
reaches VSWITCH, then a 2.2 ohm resistor must be connected
between VCC and the system supply to avoid momentary
excess of current between VCC and VCAP.
AutoStore Inhibit Mode
If an automatic STORE on power loss is not required, then VCC
is tied to ground and +5V is applied to VCAP (Figure 4). This is
the AutoStore Inhibit mode, where the AutoStore function is
disabled. If the STK12C68-5 is operated in this configuration,
references to VCC are changed to VCAP throughout this data
sheet. In this mode, STORE operations are triggered through
software control or the HSB pin. To enable or disable Autostore
using an IO port pin see Preventing Store on page 5. It is not
permissible to change between these three options “on the
fly”.
Hardware STORE (HSB) Operation
The STK12C68-5 provides the HSB pin for controlling and
acknowledging the STORE operations. The HSB pin is used
to request a hardware STORE cycle. When the HSB pin is
driven LOW, the STK12C68-5 conditionally initiates a STORE
operation after tDELAY. An actual STORE cycle only begins if a
Write to the SRAM takes place since the last STORE or
RECALL cycle. The HSB pin also acts as an open drain driver
that is internally driven LOW to indicate a busy condition, while
the STORE (initiated by any means) is in progress.
SRAM Read and Write operations, that are in progress when
HSB is driven LOW by any means, are given time to complete
before the STORE operation is initiated. After HSB goes LOW,
the STK12C68-5 continues SRAM operations for tDELAY.
During tDELAY, multiple SRAM Read operations take place. If
a Write is in progress when HSB is pulled LOW, it allows a
time, tDELAY to complete. However, any SRAM Write cycles
requested after HSB goes LOW are inhibited until HSB returns
HIGH.
Document Number: 001-51026 Rev. **
Data is transferred from the SRAM to the nonvolatile memory
by a software address sequence. The STK12C68-5 software
STORE cycle is initiated by executing sequential CE controlled
Read cycles from six specific address locations in exact order.
During the STORE cycle, an erase of the previous nonvolatile
data is first performed followed by a program of the nonvolatile
elements. When a STORE cycle is initiated, input and output
are disabled until the cycle is completed.
Because a sequence of Reads from specific addresses is
used for STORE initiation, it is important that no other Read or
Write accesses intervene in the sequence. If they intervene,
the sequence is aborted and no STORE or RECALL takes
place.
To initiate the software STORE cycle, the following Read
sequence is performed:
1. Read address 0x0000, Valid READ
2. Read address 0x1555, Valid READ
3. Read address 0x0AAA, Valid READ
4. Read address 0x1FFF, Valid READ
5. Read address 0x10F0, Valid READ
6. Read address 0x0F0F, Initiate STORE cycle
The software sequence is clocked with CE controlled Reads
or OE controlled Reads. When the sixth address in the
sequence is entered, the STORE cycle commences and the
chip is disabled. It is important that Read cycles and not Write
cycles are used in the sequence. It is not necessary that OE
is LOW for a valid sequence. After the tSTORE cycle time is
fulfilled, the SRAM is again activated for Read and Write
operation.
Software RECALL
Data is transferred from the nonvolatile memory to the SRAM
by a software address sequence. A software RECALL cycle is
initiated with a sequence of Read operations in a manner
similar to the software STORE initiation. To initiate the
RECALL cycle, the following sequence of CE controlled Read
operations is performed:
1. Read address 0x0000, Valid READ
2. Read address 0x1555, Valid READ
3. Read address 0x0AAA, Valid READ
Page 4 of 18
[+] Feedback
STK12C68-5 (SMD5962-94599)
4. Read address 0x1FFF, Valid READ
5. Read address 0x10F0, Valid READ
6. Read address 0x0F0E, Initiate RECALL cycle
Figure 5. Current Versus Cycle Time (Read)
Internally, RECALL is a two step procedure. First, the SRAM data
is cleared; then, the nonvolatile information is transferred into the
SRAM cells. After the tRECALL cycle time, the SRAM is again
ready for Read and Write operations. The RECALL operation
does not alter the data in the nonvolatile elements. The nonvolatile data can be recalled an unlimited number of times.
Data Protection
The STK12C68-5 protects data from corruption during low
voltage conditions by inhibiting all externally initiated STORE
and Write operations. The low voltage condition is detected
when VCC is less than VSWITCH. If the STK12C68-5 is in a Write
mode (both CE and WE are low) at power up after a RECALL or
after a STORE, the Write is inhibited until a negative transition
on CE or WE is detected. This protects against inadvertent writes
during power up or brown out conditions.
Figure 6. Current Versus Cycle Time (Write)
Noise Considerations
The STK12C68-5 is a high speed memory. It must have a high
frequency bypass capacitor of approximately 0.1 µF connected
between VCC and VSS, using leads and traces that are as short
as possible. As with all high speed CMOS ICs, careful routing of
power, ground, and signals reduce circuit noise.
Hardware Protect
The STK12C68-5 offers hardware protection against inadvertent
STORE operation and SRAM Writes during low voltage conditions. When VCAP<VSWITCH, all externally initiated STORE
operations and SRAM Writes are inhibited. AutoStore can be
completely disabled by tying VCC to ground and applying +5V to
VCAP. This is the AutoStore Inhibit mode; in this mode, STOREs
are only initiated by explicit request using either the software
sequence or the HSB pin.
Low Average Active Power
CMOS technology provides the STK12C68-5 the benefit of
drawing significantly less current when it is cycled at times longer
than 50 ns. Figure 5 and Figure 6 shows the relationship
between ICC and Read or Write cycle time. Worst case current
consumption is shown for both CMOS and TTL input levels
(commercial temperature range, VCC = 5.5V, 100% duty cycle
on chip enable). Only standby current is drawn when the chip is
disabled. The overall average current drawn by the STK12C68-5
depends on the following items:
■
The duty cycle of chip enable
■
The overall cycle rate for accesses
■
The ratio of Reads to Writes
■
CMOS versus TTL input levels
■
The operating temperature
■
The VCC level
Document Number: 001-51026 Rev. **
Preventing Store
The STORE function is disabled by holding HSB high with a
driver capable of sourcing 30 mA at a VOH of at least 2.2V,
because it must overpower the internal pull down device. This
device drives HSB LOW for 20 μs at the onset of a STORE.
When the STK12C68-5 is connected for AutoStore operation
(system VCC connected to VCC and a 68 μF capacitor on VCAP)
and VCC crosses VSWITCH on the way down, the STK12C68-5
attempts to pull HSB LOW. If HSB does not actually get below
VIL, the part stops trying to pull HSB LOW and abort the STORE
attempt.
Page 5 of 18
[+] Feedback
STK12C68-5 (SMD5962-94599)
Best Practices
nvSRAM products have been used effectively for over 15
years. While ease-of-use is one of the product’s main system
values, experience gained working with hundreds of applications has resulted in the following suggestions as best
practices:
■
The nonvolatile cells in an nvSRAM are programmed on the
test floor during final test and quality assurance. Incoming
inspection routines at customer or contract manufacturer’s
sites sometimes reprograms these values. Final NV patterns
are typically repeating patterns of AA, 55, 00, FF, A5, or 5A.
The end product’s firmware must not assume that an NV
array is in a set programmed state. Routines that check
memory content values to determine first time system configuration, cold or warm boot status, and so on must always
program a unique NV pattern (for example, complex 4-byte
pattern of 46 E6 49 53 hex or more random bytes) as part of
the final system manufacturing test to ensure these system
routines work consistently.
■
Power up boot firmware routines must rewrite the nvSRAM
into the desired state. While the nvSRAM is shipped in a
preset state, best practice is to again rewrite the nvSRAM
into the desired state as a safeguard against events that
might flip the bit inadvertently (program bugs, incoming
inspection routines, and so on).
■
The Vcap value specified in this data sheet includes a
minimum and a maximum value size. The best practice is to
meet this requirement and not exceed the maximum Vcap
value because the higher inrush currents may reduce the
reliability of the internal pass transistor. Customers who want
to use a larger Vcap value to make sure there is extra store
charge must discuss their Vcap size selection with Cypress.
Table 1. Hardware Mode Selection
CE
WE
HSB
A12–A0
Mode
IO
Power
H
X
H
X
Not Selected
Output High Z
Standby
L
H
H
X
Read SRAM
Output Data
Active[3]
L
L
H
X
Write SRAM
Input Data
Active
X
X
L
X
Nonvolatile STORE
Output High Z
ICC2[1]
L
H
H
0x0000
0x1555
0x0AAA
0x1FFF
0x10F0
0x0F0F
Read SRAM
Read SRAM
Read SRAM
Read SRAM
Read SRAM
Nonvolatile STORE
Output Data
Output Data
Output Data
Output Data
Output Data
Output High Z
Active ICC2[2, 3]
L
H
H
0x0000
0x1555
0x0AAA
0x1FFF
0x10F0
0x0F0E
Read SRAM
Read SRAM
Read SRAM
Read SRAM
Read SRAM
Nonvolatile RECALL
Output Data
Output Data
Output Data
Output Data
Output Data
Output High Z
Active[2, 3]
Notes
1. HSB STORE operation occurs only if an SRAM Write is done since the last nonvolatile cycle. After the STORE (If any) completes, the part goes into standby
mode, inhibiting all operations until HSB rises.
2. The six consecutive addresses must be in the order listed. WE must be high during all six consecutive CE controlled cycles to enable a nonvolatile cycle.
3. IO state assumes OE < VIL. Activation of nonvolatile cycles does not depend on state of OE.
Document Number: 001-51026 Rev. **
Page 6 of 18
[+] Feedback
STK12C68-5 (SMD5962-94599)
Maximum Ratings
Voltage on DQ0-7 or HSB .......................–0.5V to Vcc + 0.5V
Exceeding maximum ratings may shorten the useful life of the
device. These user guidelines are not tested.
Storage Temperature ................................. –65°C to +150°C
Power Dissipation.......................................................... 1.0W
DC output Current (1 output at a time, 1s duration) .... 15 mA
Operating Range
Temperature under Bias ............................. –55°C to +125°C
Range
Voltage on Input Relative to GND.....................–0.5V to 7.0V
Voltage on Input Relative to Vss............ –0.6V to VCC + 0.5V
Ambient Temperature
VCC
-55°C to +125°C
4.5V to 5.5V
Military
DC Electrical Characteristics
Over the operating range (VCC = 4.5V to 5.5V) [4]
Max
Unit
ICC1
Parameter
Average VCC Current
Description
tRC = 35 ns
tRC = 55 ns
Dependent on output loading and cycle rate. Values
obtained without output loads.
IOUT = 0 mA.
Test Conditions
Min
75
55
mA
mA
ICC2
Average VCC Current
during STORE
All Inputs Do Not Care, VCC = Max
Average current for duration tSTORE
3
mA
ICC3
Average VCC Current at WE > (VCC – 0.2V). All other inputs cycling.
tRC= 200 ns, 5V, 25°C Dependent on output loading and cycle rate. Values
obtained without output loads.
Typical
10
mA
ICC4
Average VCAP Current All Inputs Do Not Care, VCC = Max
during AutoStore Cycle Average current for duration tSTORE
2
mA
ISB1[5]
VCC Standby Current tRC = 35 ns, CE > VIH
(Standby, Cycling TTL tRC = 55 ns, CE > VIH
Input Levels)
24
19
mA
mA
ISB2 [5]
VCC Standby Current
2.5
mA
IIX
-1
+1
μA
IOZ
Input Leakage Current VCC = Max, VSS < VIN < VCC
Off State Output
VCC = Max, VSS < VIN < VCC, CE or OE > VIH or WE < VIL
Leakage Current
-5
+5
μA
VIH
Input HIGH Voltage
2.2
VCC + 0.5
V
VIL
Input LOW Voltage
VSS – 0.5
0.8
V
VOH
Output HIGH Voltage
IOUT = –4 mA
VOL
Output LOW Voltage
IOUT = 8 mA
0.4
V
VBL
Logic ‘0’ Voltage on
HSB Output
IOUT = 3 mA
0.4
V
VCAP
Storage Capacitor
Between Vcap pin and Vss, 6V rated. 68 µF +20% nom.
260
µF
CE > (VCC – 0.2V). All others VIN < 0.2V or > (VCC – 0.2V).
Standby current level after nonvolatile cycle is complete.
Inputs are static. f = 0 MHz.
2.4
54
V
Notes
4. VCC reference levels throughout this data sheet refer to VCC if that is where the power supply connection is made, or VCAP if VCC is connected to ground.
5. CE > VIH does not produce standby current levels until any nonvolatile cycle in progress has timed out.
Document Number: 001-51026 Rev. **
Page 7 of 18
[+] Feedback
STK12C68-5 (SMD5962-94599)
Data Retention and Endurance
Parameter
Description
DATAR
Data Retention
NVC
Nonvolatile STORE Operations
Min
Unit
100
Years
1,000
K
Capacitance
In the following table, the capacitance parameters are listed.[6]
Parameter
Description
CIN
Input Capacitance
COUT
Output Capacitance
Test Conditions
Max
TA = 25°C, f = 1 MHz,
VCC = 0 to 3.0 V
Unit
8
pF
7
pF
Thermal Resistance
In the following table, the thermal resistance parameters are listed.[6]
Parameter
ΘJA
ΘJC
Description
Thermal Resistance
(Junction to Ambient)
Thermal Resistance
(Junction to Case)
Test Conditions
28-CDIP 28-LCC
Test conditions follow standard test methods and
procedures for measuring thermal impedance, per
EIA / JESD51.
Unit
TBD
TBD
°C/W
TBD
TBD
°C/W
Figure 7. AC Test Loads
R1 963Ω
R1 963Ω For Tri-state Specs
5.0V
5.0V
Output
Output
30 pF
R2
512Ω
5 pF
R2
512Ω
AC Test Conditions
Input Pulse Levels .................................................... 0V to 3V
Input Rise and Fall Times (10% to 90%) ...................... <5 ns
Input and Output Timing Reference Levels .......................1.5
Note
6. These parameters are guaranteed by design and are not tested.
Document Number: 001-51026 Rev. **
Page 8 of 18
[+] Feedback
STK12C68-5 (SMD5962-94599)
AC Switching Characteristics
SRAM Read Cycle
Parameter
Cypress
Parameter
tACE
tRC
[7]
35 ns
Description
Alt
Min
tELQV
Chip Enable Access Time
tAVAV, tELEH
Read Cycle Time
tAVQV
Address Access Time
tDOE
tGLQV
Output Enable to Data Valid
tOHA [8]
tAXQX
Output Hold After Address Change
5
[9]
tELQX
Chip Enable to Output Active
5
tHZCE [9]
tEHQZ
Chip Disable to Output Inactive
[9]
tGLQX
Output Enable to Output Active
tHZOE [9]
tGHQZ
Output Disable to Output Inactive
tPU [6]
tELICCH
Chip Enable to Power Active
tPD [6]
tEHICCL
Chip Disable to Power Standby
tLZOE
Max
Min
Max
35
tAA [8]
tLZCE
55 ns
35
55
55
15
55
ns
35
ns
5
ns
5
ns
10
12
ns
12
ns
55
ns
0
ns
10
0
ns
ns
35
0
Unit
0
ns
35
Switching Waveforms
Figure 8. SRAM Read Cycle 1: Address Controlled [7, 8]
W5&
$''5(66
W $$
W2+$
'4'$7$287
'$7$9$/,'
Figure 9. SRAM Read Cycle 2: CE and OE Controlled [7]
W5&
$''5(66
W$&(
W3'
W/=&(
&(
W+=&(
2(
W+=2(
W'2(
W/=2(
'4'$7$287
'$7$9$/,'
W 38
,&&
$&7,9(
67$1'%<
Notes
7. WE and HSB must be High during SRAM Read cycles.
8. Device is continuously selected with CE and OE both Low.
9. Measured ±200 mV from steady state output voltage.
Document Number: 001-51026 Rev. **
Page 9 of 18
[+] Feedback
STK12C68-5 (SMD5962-94599)
SRAM Write Cycle
Parameter
Cypress
Alt
Parameter
tWC
tAVAV
tPWE
tWLWH, tWLEH
tSCE
tELWH, tELEH
tSD
tDVWH, tDVEH
tHD
tWHDX, tEHDX
tAW
tAVWH, tAVEH
tSA
tAVWL, tAVEL
tHA
tWHAX, tEHAX
tHZWE [9,10]
tWLQZ
tLZWE [9]
tWHQX
35 ns
Description
Min
Write Cycle Time
Write Pulse Width
Chip Enable To End of Write
Data Setup to End of Write
Data Hold After End of Write
Address Setup to End of Write
Address Setup to Start of Write
Address Hold After End of Write
Write Enable to Output Disable
Output Active After End of Write
55 ns
Max
Min
35
25
25
12
0
25
0
0
Max
55
45
45
25
0
45
0
0
13
15
5
5
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Switching Waveforms
Figure 10. SRAM Write Cycle 1: WE Controlled [11, 12]
tWC
ADDRESS
tHA
tSCE
CE
tAW
tSA
tPWE
WE
tHD
tSD
DATA VALID
DATA IN
tHZWE
DATA OUT
HIGH IMPEDANCE
PREVIOUS DATA
tLZWE
Figure 11. SRAM Write Cycle 2: CE Controlled [11, 12]
tWC
ADDRESS
CE
WE
tHA
tSCE
tSA
tAW
tPWE
tSD
DATA IN
DATA OUT
tHD
DATA VALID
HIGH IMPEDANCE
Notes
10. If WE is Low when CE goes Low, the outputs remain in the high impedance state.
11. HSB must be high during SRAM Write cycles.
12. CE or WE must be greater than VIH during address transitions.
Document Number: 001-51026 Rev. **
Page 10 of 18
[+] Feedback
STK12C68-5 (SMD5962-94599)
AutoStore or Power Up RECALL
Parameter
STK12C68-5
Alt
Description
tRESTORE
Power up RECALL Duration
550
μs
tSTORE [14, 15, 16] tHLHZ
STORE Cycle Duration
10
ms
tDELAY [9, 15]
Time Allowed to Complete SRAM Cycle
tHRECALL [13]
tHLQZ , tBLQZ
VSWITCH
Low Voltage Trigger Level
VRESET
Low Voltage Reset Level
tVCCRISE
VCC Rise Time
tVSBL[11]
Low Voltage Trigger (VSWITCH) to HSB Low
Min
Max
μs
1
4.0
Unit
4.5
3.9
V
V
μs
150
300
ns
Switching Waveform
Figure 12. AutoStore/Power Up RECALL
WE
Notes
13. tHRECALL starts from the time VCC rises above VSWITCH.
14. CE and OE low for output behavior.
15. CE and OE low and WE high for output behavior.
16. HSB is asserted low for 1us when VCAP drops through VSWITCH. If an SRAM Write has not taken place since the last nonvolatile cycle, HSB is released and no store
takes place.
Document Number: 001-51026 Rev. **
Page 11 of 18
[+] Feedback
STK12C68-5 (SMD5962-94599)
Software Controlled STORE/RECALL Cycle
The software controlled STORE/RECALL cycle follows. [18]
Parameter
Alt
35 ns
Description
Min
55 ns
Max
Min
Max
Unit
tRC[14]
tAVAV
STORE/RECALL Initiation Cycle Time
35
55
ns
tSA[17]
tAVEL
Address Setup Time
0
0
ns
tCW[17]
tHACE[17]
tELEH
Clock Pulse Width
25
30
ns
tELAX
Address Hold Time
20
20
ns
tRECALL
RECALL Duration
20
20
μs
Switching Waveform
Figure 13. CE Controlled Software STORE/RECALL Cycle [18]
tRC
ADDRESS # 1
ADDRESS
tSA
tRC
ADDRESS # 6
tSCE
CE
tHACE
OE
t STORE / t RECALL
DQ (DATA)
DATA VALID
DATA VALID
HIGH IMPEDANCE
Notes
17. The software sequence is clocked on the falling edge of CE without involving OE (double clocking aborts the sequence).
18. The six consecutive addresses must be read in the order listed in Table 1 on page 6. WE must be HIGH during all six consecutive cycles.
Document Number: 001-51026 Rev. **
Page 12 of 18
[+] Feedback
STK12C68-5 (SMD5962-94599)
Hardware STORE Cycle
Parameter
Alt
Description
tSTORE [9, 14]
tHLHZ
tDHSB [14, 19]
tRECOVER, tHHQX Hardware STORE High to Inhibit Off
tPHSB
tHLHX
tHLBL
STK12C68-5
Min
STORE Cycle Duration
Hardware STORE Pulse Width
Hardware STORE Low to STORE Busy
Max
Unit
10
ms
700
ns
15
ns
300
ns
Switching Waveform
Figure 14. Hardware STORE Cycle
Note
19. tDHSB is only applicable after tSTORE is complete.
Document Number: 001-51026 Rev. **
Page 13 of 18
[+] Feedback
STK12C68-5 (SMD5962-94599)
Part Numbering Nomenclature
STK12C68 - 5 C 35 M
Temperature Range:
M - Military (-55 to 125°C)
Speed:
35 - 35 ns
55 - 55 ns
Package:
C = Ceramic 28-pin 300 mil DIP (gold lead finish)
K = Ceramic 28-pin 300 mil DIP (Solder dip finish)
L = Ceramic 28-pin LLC
Retention / Endurance
5 = Military (10 years or 105 cycles)
SMD5962 - 94599 01 MX X
Lead Finish
A = Solder DIP lead finish
C = Gold lead DIP finish
X = Lead finish “A” or “C” is acceptable
Case Outline
X = Ceramic 28-pin 300 mil DIP
Y = Ceramic 28-pin LLC
Device Class Indicator - Class M
Device Type:
01 = 55 ns
03 = 35 ns
Document Number: 001-51026 Rev. **
Page 14 of 18
[+] Feedback
STK12C68-5 (SMD5962-94599)
Ordering Information
Speed (ns)
35
55
Ordering Code
Package Diagram
Package Type
STK12C68-5C35M
001-51695
28-pin CDIP (300 mil)
STK12C68-5K35M
001-51695
28-pin CDIP (300 mil)
STK12C68-5L35M
001-51696
28-pin LCC (350 mil)
STK12C68-5C55M
001-51695
28-pin CDIP (300 mil)
STK12C68-5K55M
001-51695
28-pin CDIP (300 mil)
STK12C68-5L55M
001-51696
28-pin LCC (350 mil)
Operating Range
Military
The above table contains Final information. Contact your local Cypress sales representative for availability of these parts
Document Number: 001-51026 Rev. **
Page 15 of 18
[+] Feedback
STK12C68-5 (SMD5962-94599)
Package Diagrams
Figure 15. 28-Pin (300-Mil) Side Braze DIL (001-51695)
001-51695 **
Document Number: 001-51026 Rev. **
Page 16 of 18
[+] Feedback
STK12C68-5 (SMD5962-94599)
Package Diagrams (continued)
Figure 16. 28-Pad (350-Mil) LCC (001-51696)
1. ALL DIMENSION ARE IN INCHES AND MILLIMETERS [MIN/MAX]
2. JEDEC 95 OUTLINE# MO-041
3. PACKAGE WEIGHT : TBD
001-51696 **
Document Number: 001-51026 Rev. **
Page 17 of 18
[+] Feedback
STK12C68-5 (SMD5962-94599)
Document History Page
Document Title: STK12C68-5 (SMD5962-94599), 64 Kbit (8K x 8) AutoStore nvSRAM
Document Number: 001-51026
Rev
ECN No.
Orig. of
Change
Submission
Date
**
2666844
GVCH/PYRS
03/02/09
Description of Change
New data sheet
Sales, Solutions, and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office
closest to you, visit us at cypress.com/sales.
Products
PSoC
Clocks & Buffers
PSoC Solutions
psoc.cypress.com
clocks.cypress.com
General
Low Power/Low Voltage
psoc.cypress.com/solutions
psoc.cypress.com/low-power
Wireless
wireless.cypress.com
Precision Analog
Memories
memory.cypress.com
LCD Drive
psoc.cypress.com/lcd-drive
image.cypress.com
CAN 2.0b
psoc.cypress.com/can
USB
psoc.cypress.com/usb
Image Sensors
psoc.cypress.com/precision-analog
© Cypress Semiconductor Corporation, 2009. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any
circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical,
life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical
components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems
application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign),
United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of,
and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress
integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without
the express written permission of Cypress.
Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not
assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where
a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer
assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Use may be limited by and subject to the applicable Cypress software license agreement.
Document Number: 001-51026 Rev. **
Revised March 02, 2009
Page 18 of 18
AutoStore and QuantumTrap are registered trademarks of Cypress Semiconductor Corporation. All products and company names mentioned in this document may be the trademarks of their respective
holders.
[+] Feedback