VECTRON TFS140G

tfs 140G.doc
Version 1.3
VI TELEFILTER
Filter Specification
28.11.2000
TFS 140G - 1/5
1. Measurement condition
Ambient temperature TA:
Input power level:
Terminating impedances at fc:
23 °C
0 dBm.
for input:
Q-value of matching elements:
Source impedance:
Load impedance:
for output:
70
50 Ω
50 Ω
180 Ω  - 16,5 pF.
200 Ω  - 12,0 pF.
2. Characteristics
Remark:
Reference level for the relative attenuation arel of the TFS 140G is the minimum of the pass band attenuation amin. The minimum of the pass
band attenuation amin is defined as the insertion loss ae. The reference frequency fc is the arithmetic mean value of the upper and lower
frequencies at the 3 dB filter attenuation level relative to the insertion loss ae. The temperature coefficient of frequency Tcf is valid both for the
reference frequency fc and the frequency response of the filter in the operating temperature range. The frequency shift of the filter in the operating
temperature range is not included in the production tolerance scheme
Data
typ. value
Insertion loss (Reference level)
18...18,5 dB
ae
fc at ambient temperature TA (fCAT)
Centre frequency
tolerance / limit
max.
140,01 MHz
140 ± 0,06 MHz
Pass band (PB) at ambient temperature TA:
Amplitude ripple (p-p):
Bandwidth
1
3
20
40
45
20 dB
fC - 0,85 MHz.....fC + 0,85 MHz
fC ..... fC ± 0,70 MHz
0,5...0,6 dB
max.
1 dB
at ambient temperature:
dB - band width
dB - band width
dB - band width
dB - band width
dB - band width
Relative attenuation
fC
fC ± 0,70
fC ± 1,30
fC ± 2,30
1,50
1,74
2,29
2,55
2,65...3,10
MHz
MHz
MHz
MHz
MHz
min. 1,40 MHz
min. 1,70 MHz
max. 2,60 MHz
max. 4,60 MHz
dB
dB
dB
dB
max.
max.
min.
min.
arel
............
MHz .....
MHz .....
MHz .....
fC ±
fC ±
fC ±
fC ±
0,70
0,85
2,30
40
MHz
MHz
MHz
MHz
Group delay ( mean value in PB ):
Group delay ripple in PB (p-p):
Deviation from linear phase in PB (p-p):
Input VSWR (S11) in PB :
Output VSWR (S22) in PB :
Triple transit attenuation compared to main signal
Crosstalk
Substrate material
Frequency inversion temperature ( To )
Temperature coefficient of frequency ( Tcf )
Frequency deviation of fc over temperature: * )
0,6
2,5
42...55
55....70
1
3
40
45
dB
dB
dB
dB
2,54 µs
140...160 ns
2,8°...4,5° ( r.m.s. 0,8° )
max. 3,0 µs
max. 200 ns
max. 5°
(1,6...1,8) : 1
(1,4...1,8) : 1
41...42 dB
55...65 dB
max. 2 : 1
max. 2 : 1
min. 40 dB
Quartz
25°...30° C
-0,036...0,045
ppm/K²
∆fc(Hz) = Tcf(ppm/K) x (T - To)² x fTo (MHz)
Operating temperature range
Storage temperature range
0 °C ... + 70 °C
- 40 °C ... + 85 °C
* ) fTo is reference frequence fc at frequency inversion temperature (To )
Generated:
Dunzow W.P.
Checked/Approved:
Dr. Bert Wall
VI TELEFILTER
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International, Inc.
267 Lowell Road
Hudson, NH 03051 / USA
Tel: (603) 598-0070 Fax: (603) 598-0075
E-Mail: [email protected]
VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed
as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.
tfs 140G.doc
Version 1.3
VI TELEFILTER
Filter Specification
28.11.2000
TFS 140G - 2/5
3. Package
D atecode:
L
M
N
.......
TF S 140
140G
TFS
G1
19
MM
44
P in
P in
P in
P in
P in
10
1
5
6
2 - 4, 7 - 9
Y ear+w eek
1999
2000
2001
..........
In put
Input R F R eturn
O utput
O utput R F R eturn
P ackage G round
4. 50 Ω matching networks ( see Application Note ):
L1
50 Ω
L3
10
9
8
7
TFS
.
R1
1
6
140 G
M 42
2
3
4
R2
L4
50 Ω
L2
5
Schem e 1
L1
10
50 Ω
C1
9
8
7
TFS
.
R1
1
2
6
140 G
M 42
3
4
5
R2
C2
=
50 Ω
L2
Schem e 2
For final test we use Scheme 1.
VI TELEFILTER
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International, Inc.
267 Lowell Road
Hudson, NH 03051 / USA
Tel: (603) 598-0070 Fax: (603) 598-0075
E-Mail: [email protected]
VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed
as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.
tfs 140G.doc
Version 1.3
VI TELEFILTER
Filter Specification
28.11.2000
TFS 140G - 3/5
5. Stability Characteristics
After the following tests the filter shall meet the whole specification:
1. Shock:
500g, 18 ms, half sine wave, 3 shocks each plane;
DIN IEC 68 T2 - 27
2. Vibration:
10 Hz to 500 Hz, 0,35 mm or 5g respectively, 1 octave per min, 10 cycles per plan, 3 plans;
DIN IEC 68 T2 - 6
3. Damp heat:
(cycle)
25 °C to 55°C / 95% r.H. / 10 cycles
DIN IEC 68 - 2 – 30 Db
4. Resistance to
solder heat (reflow):
max. 2 times reflow process;
for temperature conditions refer to the attached "Air reflow temperature conditions" on page 4;
6. Packing
Tape & Reel:
DIN IEC 286 - 3, with exception of value for N and minimum bending radius;
tape type II, embossed carrier tape with top cover tape on the upper side;
max. pieces of filters per reel:
Real of empty components at start:
Real of empty components at start including leader:
Trailer
2000
min 300 mm
min 500 mm
min 300 mm
EMBOSSED CARRIER TAPE
Tape (all dimensions in mm)
Do
W
Po
Do
E
F
G (min)
P2
P1
D1(min)
Ao
Bo
t
CT
:
:
:
:
:
:
:
:
:
:
:
:
:
32
± 0,3
4
± 0,1
1,5
+ 0,1
1,75 ± 0,1
14,2 ± 0,1
0,6
2
± 0,1
12
± 0,1
2,0
7,1
± 0,1
19,6 ± 0,
0,3
± 0,05
25,5 ± 0,1
Po
P
2
E
A
o
F
D
CT
1
W
Bo
G
P1
COVER TAPE
W 2
Reel (all dimensions in mm):
A
:
W1
W2 (max) :
:
N (min)
:
330
32,4 +2
38,4
100
C
C
:
13 +0,5/-0,2
A
N
W 1
The minimum bending radius is 45 mm. The mounting surface of the filters faces the bottom side of the embossed carrier tape.
The marking of the filters is able to read if the view is directed on the upper side of the carrier tape with the sprocket holes on
the right side of the tape.
VI TELEFILTER
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International, Inc.
267 Lowell Road
Hudson, NH 03051 / USA
Tel: (603) 598-0070 Fax: (603) 598-0075
E-Mail: [email protected]
VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed
as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.
tfs 140G.doc
Version 1.3
VI TELEFILTER
Filter Specification
28.11.2000
TFS 140G - 4/5
7. Air reflow temperature conditions
1st and 2nd air reflow profile
Name:
Temperature:
Time:
pre-heating periods
150 °C - 170 °C
60 sec. - 90 sec.
main-heating periods
over 200 °C
20 sec. - 25 sec.
peak temperature
255 °C ± 5 °C
Air reflow profile
260
240
220
200
temperature / °C
180
160
140
120
100
80
60
40
20
0
0
20
40
60
80
100
120
140
160
180
200
220
240
time / sec.
Table for temperature vs. time during the air reflow process
Tolerance of temperatures: ± 5 °C
time / sec.
0
10
20
30
40
50
60
70
80
90
100
110
120
130
temperature / °C
23
34
46
60
80
103
121
134
143
150
154
156
158
159
VI TELEFILTER
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
time / sec.
140
150
160
170
180
190
195
200
205
210
215
220
230
240
temperature / °C
160
161
164
170
180
205
230
255
230
205
180
165
140
120
Vectron International, Inc.
267 Lowell Road
Hudson, NH 03051 / USA
Tel: (603) 598-0070 Fax: (603) 598-0075
E-Mail: [email protected]
VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed
as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.
tfs 140G.doc
Version 1.3
VI TELEFILTER
Filter Specification
28.11.2000
TFS 140G - 5/5
8. History
Version
Reason of Changes
Name
Date
1.0
Generate specification according to customer requirements
Modify insertion loss and triple transit attenuation according to our simulations
Dunzow W.
03.05.2000
1.1
Change next parameters according to customer requirements :
- filter name from TFS 140G1 to TFS 140G,
- limit value of ILo from ILo = max. 19 dB to ILo = max. 20 dB,
- limit value of Centre frequency from 140 ± 0,03 MHz to 140 ± 0,06 MHz,
- limit value of Pass band from fC ± 0,77 MHz to fC ± 0,80 MHz,
- limit value of Stop band from fC ± 1,20 MHz to fC ± 1,25 MHz,
- limit value of TTS from min. 37 dB to min. 40 dB,
- input and output pin positions.
Add next parameters according to customer requirements:
- limit value of VSWR : max. 2 : 1 ,
- theoretical matching network scheme.
Dunzow W.
22.06.2000
1.2
Change the following parameters according to customer requirements :
- limit value of Pass band from fC ± 0,8 MHz to fC ± 0,85 MHz,
- Relative attenuation (3 dB) from fC ± 0,8 MHz to fC ± 0,85 MHz,
- Relative attenuation (40 dB) from fC ± 1,25 MHz to fC ± 1,3 MHz,
A Jaffer
13.09.2000
1.3
Generate Filter specification.
Add limit value of ripple in fC - 0,7 MHz .... fC + 0,7 MHz. max. 1 dB.
Dunzow W.
28.11.2000
VI TELEFILTER
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International, Inc.
267 Lowell Road
Hudson, NH 03051 / USA
Tel: (603) 598-0070 Fax: (603) 598-0075
E-Mail: [email protected]
VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed
as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.