ThunderLAN TNETE100 PCI ETHERNET CONTROLLER SINGLE-CHIP 10 BASE-T WITH MII FOR 100 BASE-T/100VG-AnyLAN SPWS017B – APRIL 1995 – REVISED AUGUST 1996 D D D D D D D D D Single-Chip Ethernet Adapter for the Peripheral Component Interconnect (PCI) Local Bus – 32-Bit PCI† Glueless Host Interface – Compliant With PCI Local-Bus Specification (Revision 2.0) – 0-MHz to 33-MHz Operation – 3-V or 5-V Input/Output (I/O) Operation – Adaptive Performance Optimization (APO) by Texas Instruments (TI ) for Highest Available PCI Bandwidth – High-Performance Bus Master Architecture With Byte-Aligning Direct Memory Access (DMA) Controller for Low Host CPU and Bus Utilization – Plug-and-Play Compatible Supports 32-Bit Data Streaming on PCI Bus – Time Division Multiplexed Static Random-Access Memory (SRAM) – 2-Gbps Internal Bandwidth Driver Compatible With All Previous ThunderLAN Components Switched-Ethernet Compatible Full-Duplex Compatible – Independent Transmit and Receive Channels – Two Transmit Channels for Demand Priority Supports Multiple Protocols With a Single Driver Suite – Optimized Shared Interrupts No On-Board Memory Required Auto-Negotiation (N-Way) Compatible Multimedia-Ready Architecture D D D D D D D D Integrated 10 Base-T and 10 Base-5 Attachment Unit Interface (AUI) Physical Layer Interface – Single-Chip IEEE 802.3 and Blue Book Ethernet-Compliant Solution – DSP-Based Digital Phase-Locked Loop (PLL) – Smart Squelch Allows for Transparent Link Testing – Transmission Waveshaping – Autopolarity (Reverse Polarity Correction) – External/Internal Loopback Including Twisted Pair and AUI – 10 Base-2 Supported via AUI Interface Media-Independent Interface (MII) for Connecting 100-Mbps External Transceivers – Compliant MII for IEEE 802.3u Transceivers – Supports 100 Base-Tx, 100 Base-T4, and 100 Base-Fx – Super Set Supports IEEE 802.12 Transceivers – Supports Ethernet and Token-Ring Framing Formats for 100VG-AnyLAN – Link-Pulse Detection for Determining Wire Rate Low-Power CMOS Technology – Green PC Compatible – Microsoft Advanced Power Management EEPROM Interface Supports Jumperless Design and Autoconfiguration Hardware Statistics Registers for Management Information Base (MIB) DMTF (Desktop Management Task Force) Compatible IEEE Standard 1149.1‡ Test-Access Port 144-Pin Quad Flat Package (PCE Suffix) Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. † The PCI Local-Bus Specification, Revision 2.0 should be used as a reference with this document. ‡ IEEE Standard 1149.1 – 1990, IEEE Standard Test-Access Port and Boundary-Scan Architecture. AnyLAN is a trademark of the Hewlett-Packard Company. ThunderLAN, Adaptive Performance Optimization, and TI are trademarks of Texas Instruments Incorporated. Ethernet is a trademark of Xerox Corporation. Microsoft is a registered trademark of Microsoft Corp. Copyright 1996, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443 1 ThunderLAN TNETE100 PCI ETHERNET CONTROLLER SINGLE-CHIP 10 BASE-T WITH MII FOR 100 BASE-T/100VG-AnyLAN SPWS017B – APRIL 1995 – REVISED AUGUST 1996 pin assignments 109 113 112 111 110 117 116 115 114 121 120 119 118 125 124 123 122 129 128 127 126 133 132 131 130 108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 69 70 71 72 65 66 67 68 61 62 63 64 57 58 59 60 53 54 55 56 49 50 51 52 45 46 47 48 PAD9 PAD8 VSSI PC/BE0 PAD7 PAD6 VSSL PAD5 PAD4 PAD3 V DDI PAD2 PAD1 PAD0 VSSI PCLKRUN EAD7 EAD6 EAD5 EAD4 VDDL EAD3 EAD2 EAD1 EAD0 VSSL EOE EALE EXLE VSSI EDCLK EDIO VDDL MTCLK MTXD0 40 41 42 43 44 36 VDDL 2 137 136 135 134 1 2 37 38 39 PAD24 PC/BE3 VSSI PIDSEL PAD23 VDDI PAD22 PAD21 PAD20 VSSI PAD19 PAD18 PAD17 VDDI PAD16 PC/BE2 PFRAME VSSL PIRDY PTRDY PDEVSEL VDDL PSTOP PPERR PSERR VSSI PPAR PC/BE1 PAD15 PAD14 VSSI PAD13 PAD12 VDDI PAD11 PAD10 141 140 139 138 144 143 142 PAD25 PAD26 VDDI PAD27 PAD28 VSSI PAD29 PAD30 VDDI PAD31 PREQ VSSL PGNT PCLK VDDL PRST PINTA VSSI TDI TDO TCLK TMS VDDI TRST FONLY VSSVCO FATEST VDDVCO FIREF VDDOSC FXTL2 FXTL1 VSSOSC ACOLN VSSR ACOLP PCE PACKAGE ( TOP VIEW ) POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443 ARCVN VDDR ARCVP FRCVN VDDR FRCVP VSSR VSST AXMTN AXMTP FXMTN FXMTP VDDT MRST VDDL MDIO VSSL MDCLK MRXER MRXDV VSSI MRXD3 MRXD2 MRXD1 VDDL MRXD0 MRCLK MCRS MCOL VDDL MTXER MTXEN MTXD3 VSSL MTXD2 MTXD1 ThunderLAN TNETE100 PCI ETHERNET CONTROLLER SINGLE-CHIP 10 BASE-T WITH MII FOR 100 BASE-T/100VG-AnyLAN SPWS017B – APRIL 1995 – REVISED AUGUST 1996 description ThunderLAN is a high-speed networking architecture that provides a complete PCI-to-10 Base-T/AUI Ethernet solution with the flexibility to handle 100-Mbps Ethernet protocols as the user’s networking demands grow. FIFO Registers PCI Bus PCI Bus Master Control Multiplexed SRAM FIFO Ethernet LAN Controller 10 / 100 Mbps 10 Base-T Physical Layer Interface 10 Base-T Ethernet 10 Base-5 (AUI) MediaIndependent Interface Figure 1. ThunderLAN Architecture The TNETE100, an implementation of the ThunderLAN architecture, is an intelligent-network protocol interface. The ThunderLAN SRAM FIFO-based architecture eliminates the need for external memory and offers a single-chip glueless PCI-to-10 Base-T/AUI (IEEE 802.3) solution with an on-board physical layer interface. Modular support for 100 Base-T (IEEE 802.3u) and 100VG-AnyLAN (IEEE 802.12) is provided by a superset of the industry-standard Media Independent Interface (MII). ThunderLAN uses a single driver suite to support multiple networking protocols. The glueless PCI interface supports 32-bit streaming, operates at speeds up to 33 MHz and is capable of internal data transfer rates up to 2 Gbps, taking full advantage of all available PCI bandwidth. The TNETE100 offers jumperless autoconfiguration using PCI configuration read / write cycles. Customizable configuration registers, which can be autoloaded from an external serial EEPROM, allow designers of TNETE100-based systems to give their systems a unique identification code. The TNETE100 PCI interface, developed in conjunction with other leaders in the semiconductor and computer industries, has been tested vigorously on multiple platforms to ensure compatibility across a wide array of available PCI products. In addition, the ThunderLAN drivers and ThunderLAN architecture use TI’s patented Adaptive Performance Optimization (APO) technology to adjust dynamically critical parameters for minimum latency, minimum host CPU utilization, and maximum system performance. This technology ensures that the maximum capabilities of the PCI interface are used by automatically tuning the adapter to the specific system in which it is operating. The MII, an industry-standard interface for connecting a variety of external IEEE 802.3u physical layer interfaces, is supported fully by the TNETE100. In addition, the TNETE100 features an IEEE 802.12-compliant superset of the MII to allow for support of 100VG-AnyLAN physical layer interfaces. This allows TNETE100-based systems to support 100 Base-Tx, 100 Base-T4, and 100VG-AnyLAN cabling schemes for maximum flexibility as each new physical layer interface becomes available in the marketplace. An intelligent protocol handler (PH) implements the serial protocols of the network. The PH is designed for minimum overhead related to multiple protocols, using common state machines to implement 95% of the total protocol handler. On transmit, the PH serializes data, adds framing and cyclic redundancy check (CRC) fields, and interfaces to the network physical layer (PHY) chip. On receive, it provides address recognition, CRC and error checking, frame disassembly, and deserialization. Data for multiple channels is passed to and from the PH by way of circular buffer pointers in the FIFO SRAM. ThunderLAN is the first multimedia-ready architecture and is capable of handling prioritized data regardless of the selected protocol. The demand-priority protocol supports two priorities of frames: normal and priority. The two transmit channels provide independent host channels for these two frame types. Carrier-sense multiple access with collision detection (CSMA / CD) protocols only support a single priority of frame, but the two channels can be used to prioritize network access. All received frames pass through the single receive channel. Compliant with IEEE Standard 1149.1 (JTAG), the TNETE100 provides a 5-pin test-access port that is used for boundary-scan testing. The TNETE100 is available in a 144-pin quad flat package. POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443 3 ThunderLAN TNETE100 PCI ETHERNET CONTROLLER SINGLE-CHIP 10 BASE-T WITH MII FOR 100 BASE-T/100VG-AnyLAN SPWS017B – APRIL 1995 – REVISED AUGUST 1996 functional block diagram TNETE100 ( ThunderLAN) TRST IEEE 1149.1 TestAccess Port TCLK TDO AXMTN Test-Access Port (TAP) ARCVP ARCVN TDI EDCLK Config EEPROM Interface EAD[7 :0] BIOS ROM and LED I/F EXLE EALE EOE ACOLN 10-Mbps Ethernet Physical Layer (PHY) Interface Config & I/O Memory Registers EDIO AUI Interface ACOLP PCI Interface (PCIIF) Configuration EEPROM Interface AXMTP TMS FXMTP FXMTN FRCVP FRCVN FXTL1 10 Base-T Interface FXTL2 S l a v e FIREF FATEST FPREGs (FIFO Pointer Registers) BIOS ROM / LED Driver Interface MTCLK MTXEN MTXER MCOL PAD[31 :0] MTXD[3 : 0] Address and Data FSRAM (FIFO SRAM) PC/BE[3 : 0] PPAR 64 PTRDY 1.5K-Byte Rx Buffer 64 PIRDY PSTOP PDEVSEL PIDSEL M a DMA Controller s t e r Bus Arbitration MRXDV MRXER 0.75K-Byte Tx Buffer MRST PSERR PREQ PGNT PCLKRUN PRST PINTA 4 MRCLK MDCLK PCLK System Control MII 0.75K-Byte Tx Buffer PPERR Error Reporting MRXD[3 : 0] MCRS 3 128Byte List PFRAME Interface Control Protocol Handler (PH) POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443 MDIO MII ThunderLAN TNETE100 PCI ETHERNET CONTROLLER SINGLE-CHIP 10 BASE-T WITH MII FOR 100 BASE-T/100VG-AnyLAN SPWS017B – APRIL 1995 – REVISED AUGUST 1996 Pin Functions PIN NAME NO. TYPE† DESCRIPTION TEST PORT TCLK 124 I Test clock. TCLK is used to clock state information and test data into and out of the device during operation of the test port. TDI 126 I Test data input. TDI is used to shift serially test data and test instructions into the device during operation of the test port. TDO 125 O Test data output. TDO is used to shift serially test data and test instructions out of the device during operation of the test port. TMS 123 I Test mode select. TMS is used to control the state of the test port controller within TNETE100. TRST 121 I Test reset. TRST is used for asynchronous reset of the test port controller. PCI INTERFACE PAD31 135 PAD30 137 PAD29 138 PAD28 140 PAD27 141 PAD26 143 PAD25 144 PAD24 1 PAD23 5 PAD22 7 PAD21 8 PAD20 9 PAD19 11 PAD18 12 PAD17 13 PAD16 15 PAD15 29 PAD14 30 PAD13 32 PAD12 33 PAD11 35 PAD10 36 PAD9 38 I/O PCI address / data bus. bus Byte 3 (most significant) of the PCI address / data bus I/O PCI address / data bus. bus Byte 2 of the PCI address / data bus I/O PCI address / data bus. bus Byte 1 of the PCI address / data bus PAD8 39 † I = input, O = output, I / O = 3-state input / output POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443 5 ThunderLAN TNETE100 PCI ETHERNET CONTROLLER SINGLE-CHIP 10 BASE-T WITH MII FOR 100 BASE-T/100VG-AnyLAN SPWS017B – APRIL 1995 – REVISED AUGUST 1996 Pin Functions (Continued) PIN NAME NO. TYPE† DESCRIPTION PCI INTERFACE (CONTINUED) PAD7 42 PAD6 43 PAD5 45 PAD4 46 PAD3 47 PAD2 49 PAD1 50 PAD0 51 PCLK 131 I PCI clock. PCLK is the clock reference for all PCI bus operations. All other PCI pins except PRST and PINTA are sampled on the rising edge of PCLK. All PCI bus timing parameters are defined with respect to this edge. PCLKRUN 53 I/O‡ Clock run control. PCLKRUN is the active-low PCI clock request /grant signal that allows the TNETE100 to indicate when an active PCI clock is required. (This is an open drain.) PC / BE3 PC / BE2 PC / BE1 PC / BE0 2 16 28 41 I/O PCI bus command and byte enables: PC / BE3 enables byte 3 (MSbyte) of the PCI address/data bus. PC / BE2 enables byte 2 of the PCI address / data bus. PC / BE1 enables byte 1 of the PCI address / data bus. PC / BE0 enables byte 0 (LSbyte) of the PCI address / data bus. I/O PCI address / data bus. bus Byte 0 (least significant) of the PCI address / data bus PDEVSEL 21 I/O PCI device select. PDEVSEL indicates that the driving device has decoded one of its addresses as the target of the current access. The TNETE100 drives PDEVSEL when it decodes an access to one of its registers. As a bus master, the TNETE100 monitors PDEVSEL to detect accesses to illegal memory addresses. PFRAME 17 I/O PCI cycle frame. PFRAME is driven by the active bus master to indicate the beginning and duration of an access. It is asserted to indicate the start of a bus transaction. PFRAME remains asserted during the transaction, and is deasserted only in the final data phase. PGNT 132 I PCI bus grant. PGNT is asserted by the system arbiter to indicate that the TNETE100 has been granted control of the PCI bus. 4 I PCI initialization device select. PIDSEL is the chip select for access to the PCI configuration registers. 128 O/D PCI interrupt. PINTA is the interrupt request from the TNETE100. PCI interrupts are shared, so this is an open-drain (wired-OR) output. PIDSEL PINTA PIRDY 19 I/O PCI initiator ready. PIRDY is driven by the active bus master to indicate that it is ready to complete the current data phase of a transaction. A data phase is not completed until both PIRDY and PTRDY are sampled asserted. When the TNETE100 is a bus master, it uses PIRDY to align incoming data on reads or outgoing data on writes with its internal RAM access synchronization (maximum one cycle at the beginning of burst). When the TNETE100 is a bus slave, it extends the access appropriately until both PIRDY and PTRDY are asserted. PTRDY 20 I/O PCI target ready. PTRDY is driven by the selected device (bus slave or target) to indicate that it is ready to complete the current data phase of a transaction. A data phase is not completed until both PIRDY and PTRDY are sampled asserted. ThunderLAN uses PTRDY to ensure every direct I/O (DIO) operation is interlocked correctly. PPAR 27 I/O PCI parity. PPAR carries even parity across PAD[31:0] and PC / BE[3:0]. It is driven by the TNETE100 during all address and write cycles as a bus master and during all read cycles as a bus slave. PPERR 24 I/O PCI parity error. PPERR indicates a data parity error on all PCI transactions except special cycles. † I = input, I / O = 3-state input / output, O / D = open-drain output ‡ Open drain 6 POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443 ThunderLAN TNETE100 PCI ETHERNET CONTROLLER SINGLE-CHIP 10 BASE-T WITH MII FOR 100 BASE-T/100VG-AnyLAN SPWS017B – APRIL 1995 – REVISED AUGUST 1996 Pin Functions (Continued) PIN NAME NO. TYPE† DESCRIPTION PCI INTERFACE (CONTINUED) I/O PCI bus request. PREQ is asserted by the TNETE100 to request control of the PCI bus. This is not a shared signal. PREQ 134 PRST 129 I PSERR 25 O/D PCI system error. PSERR indicates parity errors or special-cycle data-parity errors. PSTOP 23 I/O PCI stop. PSTOP indicates the current target is requesting the master to stop the current transaction. PCI reset signal BIOS ROM / LED DRIVER INTERFACE EAD7 EAD6 EAD5 EAD4 EAD3 EAD2 EAD1 EAD0 54 55 56 57 59 60 61 62 I/O EPROM address / data. EAD[7:0] is a multiplexed byte bus that is used to address and read data from an external BIOS ROM. • On the cycle when EXLE is asserted low, EAD[7:0] is driven with the high byte of the address. • On the cycle when EALE is asserted low, EAD[7:0] is driven with the low byte of the address. • When EOE is asserted, BIOS ROM data should be placed on the bus. These pins can be used also to drive external status LEDs. Low-current (2 – 5 mA) LEDs can be connected directly (through appropriate resistors). High-current LEDs can be driven through buffers or from the BIOS ROM address latches. EALE 65 O EPROM address latch enable. EALE is driven low to latch the low (least significant) byte of the BIOS ROM address from EAD[0 :7]. EOE 64 O EPROM output enable. When EOE is active (low), EAD[0 :7] is 3-stated, and the output of the BIOS ROM should be placed on EAD[0 :7]. EXLE 66 O EPROM extended address-latch enable. EXLE is driven low to latch the high (most significant) byte of the BIOS ROM address from EAD[0 :7]. CONFIGURATION EEPROM INTERFACE EDCLK 68 O EEPROM data clock. EDCLK transfers serial clocked data to the 2K-bit serial EEPROMs (24C02) (see Note 1). EDIO 69 I/O EEPROM data I / O. EDIO is the bidirectional serial data / address line to the 2K-bit serial EEPROM (24C02). EDIO requires an external pullup for EEPROM operation. Tying EDIO to ground disables the EEPROM interface and prevents autoconfiguration of the PCI configuration register. MEDIA-INDEPENDENT INTERFACE (100-Mbps CSMA / CD AND DEMAND PRIORITY) MCOL 80 I Collision sense • In CSMA / CD mode, assertion of MCOL indicates a network collision. • In demand-priority mode, MCOL (active low) is used to acknowledge a transmission request. The TNETE100 begins frame transmission 50 MTCLK cycles after the assertion (low) of MCOL. MCRS 81 I Carrier sense. MCRS indicates a frame-carrier signal is being received. MDCLK 91 O Management data clock. MDCLK is part of the serial management interface to physical-media independent (PMI) / PHY chip. MDIO 93 I/O Management data I / O. MDIO is part of the serial management interface to PMI / PHY chip. MRCLK 82 I Receive clock. MRCLK is the receive clock source from the attached PHY and PMI device. MRST 95 O MII reset. MRST is the reset signal to the PMI / PHY front-end (active low). † I = input, O = output, I / O = 3-state input / output, O / D = open-drain output NOTE 1: This pin should be tied to VDD with a 4.7-kW – 10-kW pullup resistor. POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443 7 ThunderLAN TNETE100 PCI ETHERNET CONTROLLER SINGLE-CHIP 10 BASE-T WITH MII FOR 100 BASE-T/100VG-AnyLAN SPWS017B – APRIL 1995 – REVISED AUGUST 1996 Pin Functions (Continued) PIN NAME NO. TYPE† DESCRIPTION MEDIA-INDEPENDENT INTERFACE (100-Mbps CSMA / CD AND DEMAND PRIORITY) (CONTINUED) MRXD0 MRXD1 MRXD2 MRXD3 83 85 86 87 I Receive data. MRXD[3 : 0] is the nibble that receives data from the physical-media-dependent (PMD) front end. In demand-priority mode, ThunderLAN reads the frame priority of incoming frames on these pins on the cycle before assertion of MRXDV (the cycle before frame reception begins). • MRXD1 indicates the transmission priority of the received frame. A value of zero indicates normal transmission, and a value of one indicates priority transmission. Data on these pins is always synchronous to MRCLK. MRXDV 89 I Receive data valid. MRXDV indicates data on MRXD[3 : 0] is valid. MRXER 90 I Receive error. MRXER indicates reception of a coding error on received data. MTCLK 71 I Transmit clock. MTCLK is the transmit clock source from the attached PHY and PMI device. MTXD0 MTXD1 MTXD2 MTXD3 72 73 74 76 O Transmit data. MTXD[3 : 0] is the nibble that transmits data from TNETE100. When MTXEN is asserted, these pins carry data to be transmitted. In demand-priority mode, the TNETE100 drives the request state of the adapter on these pins when MTXEN is not asserted (frame transmission not in progress). • MTXD0 asserted indicates the TNETE100 is requesting frame transmission. • MTXD1 indicates the transmission priority required. A value of zero indicates normal transmission, and a value of one indicates high-priority transmission. Data on these pins is always synchronous to MTCLK. MTXER 78 O Transmit error. MTXER allows coding errors to be propagated across the MII. MTXEN 77 O Transmit enable. MTXEN indicates valid transmit data on MTXD[3 : 0]. ACOLN ACOLP 111 109 A AUI receive pair. ACOLN and ACOLP are differential line receiver inputs and connect to receive pair through transformer isolation, etc. ARCVN ARCVP 108 106 A AUI receive pair. ARCVN and ARCVP are differential line receiver inputs and connect to receive pair through transformer isolation, etc. AXMTP AXMTN 99 100 A AUI transmit pair. AXMTP and AXMTN are differential line transmitter outputs. FATEST 118 A Analog test pin. FATEST provides access to the filter of the reference PLL. This pin should be left as a “no connect.” FIREF 116 A Current reference. FIREF is used to set a current reference for the analog circuitry. FONLY 120 A Front-end only pin. When FONLY is tied high, all TNETE100 functions other than the on-chip front end are disabled. The MII interface pins allow the PHY to be used as a stand-alone 10 Base-T front end. FRCVN FRCVP 105 103 A 10 Base-T receive pair. FRCVN and FRCVP are differential line receiver inputs and connect to receive pair through transformer isolation, etc. FXTL1 FXTL2 113 114 A Crystal oscillator pins. Drive FXTL1 from a 20-MHz crystal oscillator module NETWORK INTERFACE (10 Base-T AND AUI) FXMTP 97 A FXMTN 98 † I = input, O = output, A = Analog 8 10 Base-T transmit pair. FXMTP and FXMTN are differential line transmitter outputs. POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443 ThunderLAN TNETE100 PCI ETHERNET CONTROLLER SINGLE-CHIP 10 BASE-T WITH MII FOR 100 BASE-T/100VG-AnyLAN SPWS017B – APRIL 1995 – REVISED AUGUST 1996 Pin Functions (Continued) PIN NAME NO. TYPE† DESCRIPTION POWER VDDI 6, 14, 34, 48, 122, 136, 142 PWR PCI VDD pins. VDDI pins provide power for the PCI I/O pin drivers. Connect VDDI pins to a 5-V power supply when using 5-V signals on the PCI bus. Connect VDDI pins to a 3-V power supply when using 3-V signals on the PCI bus VDDL 22, 37, 58, 70, 79, 84, 94, 130 PWR Logic VDD pins (5 V). VDDL pins provide power for internal TNETE100 logic, and they should always be connected to a 5-V power supply. VDDOSC 115 PWR Analog power pin. VDDOSC is the 5-V power for the crystal oscillator circuit. VDDR 104 107 PWR Analog power pin. VDDR is the 5-V power for the receiver circuitry. 96 PWR Analog power pin. VDDT is the 5-V power for the transmitter circuitry. VDDT VDDVCO 117 PWR Analog power pin. VDDVCO is the 5-V power for the voltage controller oscillator (VCO) and filter input. VSSI 3, 10, 26, 31, 40, 52, 67, 88, 127, 139 PWR PCI I / O ground pins VSSL 18, 44, 63, 75, 92, 133 PWR Logic ground pins VSSOSC 112 PWR Analog power pin. Ground for crystal oscillator circuit VSSR 102 110 PWR Analog power pin. Ground for receiver circuitry VSST 101 PWR Analog power pin. Ground for transmitter circuitry 119 PWR Analog power pin. Ground for VCO and filter input VSSVCO † PWR = power architecture The major blocks of the TNETE100 include the PCI interface (PCIIF), protocol handler (PH), physical layer (PHY), FIFO pointer registers (FPREGS), FIFO SRAM (FSRAM), and a test-access port (TAP). The functionality of these blocks is described in the following sections. PCI interface (PCIIF) The TNETE100 PCIIF contains a byte-aligning DMA controller that allows frames to be fragmented into any byte length and transferred to any byte address while supporting 32-bit data streaming. For multipriority networks, it can provide multiple data channels, each with separate lists, commands, and status. Data for the channels is passed to and from the PH by way of circular buffer FIFOs in the SRAM, controlled through FIFO registers. The configuration EEPROM interface, BIOS ROM /LED driver interface, configuration and I / O memory registers, and DMA controller are subblocks of the PCIIF. The features of these subblocks are described in the following subsections. configuration EEPROM interface (CEI) The CEI provides a means for autoconfiguration of the PCI configuration registers. Certain registers in the PCI configuration space can be loaded using the CEI. Autoconfiguration allows builders of TNETE100-based systems to customize the contents of these registers to identify their own system, rather than to use the TI defaults. The EEPROM is read at power up and can then be read from, and written to, under program control. POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443 9 ThunderLAN TNETE100 PCI ETHERNET CONTROLLER SINGLE-CHIP 10 BASE-T WITH MII FOR 100 BASE-T/100VG-AnyLAN SPWS017B – APRIL 1995 – REVISED AUGUST 1996 PCI interface (PCIIF) (continued) BIOS ROM/LED driver interface (BRI) The BRI addresses and reads data from an external BIOS ROM through a multiplexed byte-wide bus. The ROM address/ data pins can also be multiplexed to drive external status LEDs. configuration and I/O memory registers (CIOREGS) The CIOREGS reside in the configuration space, which is 256 bytes in length. The first 64 bytes of the configuration space is the header region, which is defined explicitly by the PCI standard. DMA controller (DMAC) The DMAC is responsible for coordinating TNETE100 requests for mastership of the PCI bus. The DMAC provides byte-aligning DMA control, allowing byte-size fragmented frames to be transferred to any byte address while supporting 32-bit data streaming. protocol handler (PH) The PH implements the serial protocols of the network. On transmit, it serializes data, adds framing and CRC fields, and interfaces to the network PHY. On receive, it provides address recognition, CRC and error checking, frame disassembly, and deserialization. Data for multiple channels is passed to and from the PH by way of circular buffer FIFOs in the FSRAM controlled through FPREGS. The PH supports a MII that is compatible with the IEEE 802.12 and IEEE 802.3u logic. media-independent interface (MII) The MII provides both MAC-level 100 Base-T (IEEE 802.3u) and 100VG-AnyLAN (IEEE 802.12) controller functions to external PHY chips that handle the PHY functions for 100-Mbps CSMA / CD and demand priority. The MII also is used to communicate with the on-chip 10 Base-T PHY. 10 Base-T physical layer (PHY) The PHY acts as an on-chip front-end providing physical layer functions for both 10 Base-5 (AUI) and 10 Base-T (twisted pair). The PHY provides Manchester encoding / decoding from MII nibble format data, smart squelch, jabber detection, link pulse detection, autopolarity control, 10 Base-T transmission waveshaping, and antialiasing filtering. Connection to the AUI drop cable for the 10 Base-T twisted pair is made through simple isolation transformers (see Figure 2) and no external filter networks are required. Suitable external termination components allow the use of either shielded or unshielded twisted-pair cable (150 W or 100 W). Some of the key features of the on-chip PHY are listed below. D D D D D D D D 10 Integrated filters Integrated MII including encoder / decoder 10 Base-T transceiver AUI transceiver Autopolarity (reverse polarity correction) Loopback for twisted pair and AUI Full-duplex mode for simultaneous 10 Base-T transmission and reception Low power POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443 ThunderLAN TNETE100 PCI ETHERNET CONTROLLER SINGLE-CHIP 10 BASE-T WITH MII FOR 100 BASE-T/100VG-AnyLAN SPWS017B – APRIL 1995 – REVISED AUGUST 1996 10 Base-T physical layer (continued) FXMTP PCI TNETE100 FXMTN RJ-45 FRCVP FRCVN Figure 2. Schematic for 10 Base-T Network Interface Using TNETE100 FIFO pointer registers (FPREGS) The FPREGS are used to implement circular buffer FIFOs in the SRAM. They are a collection of pointer and counter registers used to maintain the FIFO operation. Both the PCIIF and PH use FPREGS to determine where to read or write data in the SRAM and to determine how much data the FIFO contains. Unique receive and transmit FIFO registers are needed for each data channel supported. FIFO SRAM (FSRAM) The FSRAM is a conventional SRAM array accessed synchronously to the PCI bus clock. Access to the RAM is allocated on a time-division multiplexed (TDM) basis, rather than through a conventional shared bus. This removes the need for bus arbitration and provides guaranteed bandwidth. Half the RAM accesses (every other cycle) are allocated to the PCI controller. It has a 64-bit access port to the RAM, giving it 1 Gbps of bandwidth, sufficient to support 32-bit data streaming on the PCI bus. The PH has one-quarter the RAM accesses, and its port may be up to 64 bits wide. A 64-bit port for the PH provides 512 Mbps of bandwidth, more than sufficient for a full-duplex 100-Mbps network. The remaining RAM accesses can be allocated toward providing even more PH bandwidth. The RAM is also accessible (for diagnostic purposes) from the TNETE100 internal data bus. Host DIO (mapped I / O) accesses are used by the host to access internal TNETE100 registers and for adapter test. D D 3.375K bytes of FSRAM – 1.5K-byte FIFO for receive – Two 0.75K-byte FIFOs for the two transmit channels – Three 128-byte lists In one-channel mode, the two transmit channels are combined giving a single 1.5K-byte FIFO for a single transmit channel. Supporting 1.5K bytes of FIFO per channel allows full frame buffering of Ethernet frames. PCI latency is such that a minimum of 500 bytes of storage is required to support 100-Mbps LANs. test-access port (TAP) Compliant with IEEE Standard 1149.1, the TAP is comprised of five pins that are used to interface serially with the device and with the board on which it is installed for boundary-scan testing. POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443 11 ThunderLAN TNETE100 PCI ETHERNET CONTROLLER SINGLE-CHIP 10 BASE-T WITH MII FOR 100 BASE-T/100VG-AnyLAN SPWS017B – APRIL 1995 – REVISED AUGUST 1996 absolute maximum ratings over operating case temperature range (unless otherwise noted)† Supply voltage range, VDD (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.5 V to 7 V Input voltage range (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.5 V to 7 V Output voltage range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.5 V to 7 V Power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.6 W Operating case temperature range, TC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 95°C Junction-to-ambient package thermal impedance, airflow = 0 lfpm, TJA(0) . . . . . . . . . . . . . . . . . . . . 28.8°C/W Junction-to-ambient package thermal impedance, airflow = 100 lfpm, TJA(100) . . . . . . . . . . . . . . . . 24.8°C/W Junction-to-case package thermal impedance, TJC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.0°C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTE 2: Voltage values are with respect to VSS, and all VSS pins should be routed so as to minimize inductance to system ground. The recommended operating conditions and the electrical characteristics tables are divided into groups, depending on pin function: D D D PCI interface pins Logic pins Physical layer pins The PCI signal pins may be operated in one of two modes shown in the PCI tables. D D 5-V signal mode 3-V signal mode recommended operating conditions (PCI interface pins only) (see Note 3) 3-V SIGNALING OPERATION VDD VIH VIL IOH Supply voltage (PCI) High-level input voltage 0.5 Low-level input voltage, TTL-level signal (see Note 4) High-level output current MIN NOM 3 3.3 VDD‡ – 0.5‡ 5-V SIGNALING OPERATION MAX MIN NOM 3.6 4.75 5 VDD + 0.5‡ 0.5‡ TTL outputs – 0.5 2.0 – 0.5 UNIT MAX 5.25 V VDD + 0.5 0.8 V –2 V mA IOL Low-level output current (see Note 5) TTL outputs 1.5 6 mA ‡ Assured by design SPICE IV Curve (See PCI specification revision 2.1 section 4.2 paragraph 2 for explanation.) NOTES: 3. PCI interface pins include VDDI, PCLKRUN, PFRAME, PTRDY, PIRDY, PSTOP, PDEVSEL, PIDSEL, PPERR, PSERR, PREQ, PGNT, PCLK, PPAR, PRST, PINTA, PAD[31 : 0], and PC/BE[3 : 0]. 4. The algebraic convention, where the more negative (less positive) limit is designated as a minimum, is used for logic-voltage levels only. 5. Output current of 2 mA is sufficient to drive five low-power Schottky TTL loads or ten advanced low-power Schottky TTL loads (worst case). 12 POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443 ThunderLAN TNETE100 PCI ETHERNET CONTROLLER SINGLE-CHIP 10 BASE-T WITH MII FOR 100 BASE-T/100VG-AnyLAN SPWS017B – APRIL 1995 – REVISED AUGUST 1996 electrical characteristics over recommended ranges of supply voltage (unless otherwise noted) (PCI interface pins) 3-V SIGNALING OPERATION TEST CONDITIONS † PARAMETER MIN VOH High-level output voltage, TTL-level signal (see Note 6) VOL Low-level output voltage, TTL-level signal IOZ High impedance output current High-impedance II Ci Input current, any input or input / output Input capacitance, any input§ Co Output capacitance, any output or input / output§ VDD = MIN, IOH = MAX 2.4‡ VDD = MAX, VDD = MAX, IOL = MAX VO = 0 V ‡ VDD = MAX, VO = VDD VI = VSS to VDD MAX 5-V SIGNALING OPERATION MIN UNIT MAX 2.4 V 0.45 0.5 10 10 – 10 – 10 V µA " 10 " 10 µA f = 1 MHz, Others at 0 V 10 10 pF f = 1 MHz, Others at 0 V 10 10 pF † For conditions shown as MIN / MAX, use the appropriate value specified under the recommended operating conditions. ‡ Assured by SPICE IV Curve (See PCI specification revision 2.1 section 4.2 paragraph 2 for explanation.) § Assured by design NOTE 6: The following signals require an external pullup resistor: PSERR, PINTA. recommended operating conditions (logic pins) (see Note 4) VDD VIH Supply voltage (5 V only) VIL IOH Low-level input voltage, TTL-level signal (see Note 5) MIN NOM 4.75 5 High-level input voltage 2 High-level output current – 0.3 MAX UNIT 5.25 V VDD + 0.3 0.8 V TTL outputs –4 V mA IOL Low-level output current (see Note 7) TTL outputs 4 mA NOTES: 4. The algebraic convention, where the more negative (less positive) limit is designated as a minimum, is used for logic-voltage levels only. 5. Output current of 2 mA is sufficient to drive five low-power Schottky TTL loads or ten advanced low-power Schottky TTL loads (worst case). 7. Logic pins include VDDL, EAD[7:0], EXLE, EALE, EOE, EDCLK, EDIO, FONLY, MTCLK, MTXEN, MTXER, MCOL, MTXD[3:0], MRXD[3:0], MCRS, MRCLK, MRXDV, MRXER, MDCLK, MDIO, MRST. electrical characteristics over recommended ranges of supply voltage (unless otherwise noted) (logic pins) TEST CONDITIONS † PARAMETER VOH VOL High-level output voltage, TTL-level signal IOZ High impedance output current High-impedance II IDD Input current Supply current VI = VSS to VDD VDD = MAX Ci Input capacitance, any input§ f = 1 MHz, Low-level output voltage, TTL-level signal VDD = MIN, VDD = MAX, IOH = MAX IOL = MAX VDD = MIN, VDD = MIN, VO = VDD VO = 0 V Output capacitance, any output or input / output§ MIN Others at 0 V Co f = 1 MHz, Others at 0 V † For conditions shown as MIN / MAX, use the appropriate value specified under the recommended operating conditions. § Assured by design POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443 MAX 2.4 UNIT V 0.5 10 – 10 V µA "10 µA 320 mA 10 pF 10 pF 13 ThunderLAN TNETE100 PCI ETHERNET CONTROLLER SINGLE-CHIP 10 BASE-T WITH MII FOR 100 BASE-T/100VG-AnyLAN SPWS017B – APRIL 1995 – REVISED AUGUST 1996 recommended operating conditions (physical layer pins) (see Note 8) JEDEC SYMBOL MIN NOM MAX UNIT VDD Supply voltage 4.75 5 5.25 V NOTE 8: Physical layer pins include VDDOSC, VDDR, VDDT, VDDVCO, ACOLN, ACOLP, ARCVN, ARCVP, AXMTP, AXMTN, FATEST, FIREF, FRCVN, FRCVP, FXTL1, FXTL2, FXMTP, and FXMTN. recommended operating conditions (10 Base-T receiver input pins) JEDEC SYMBOL VI(DIFF) Differential input voltage† I(CM) Common-mode current† † Recommended operating conditions VID IIC MIN MAX 0.6 2.8 4 UNIT V mA recommended operating conditions (AUI receiver input pins) JEDEC SYMBOL VI(DIFF)1 Differential input voltage 1† VID(1) † VI(DIFF)2 Differential input voltage 2 VID(2) † Recommended operating conditions NOTES: 9. Common-mode frequency range: 0 Hz to 40 kHz 10. Common-mode frequency range: 40 kHz to 10 MHz TEST CONDITIONS MIN MAX See Note 9 0 3 See Note 10 0 100 UNIT V mV electrical characteristics over recommended ranges of supply voltage (unless otherwise noted) (physical layer pins) 10 Base-T receiver input (FRCVP, FRCVN) JEDEC SYMBOL PARAMETER VSQ+ VSQ – TEST CONDITIONS Rising input pair squelch threshold VCM = VSB, See Note 11 Falling input pair squelch threshold VCM = VSB, See Note 11 MIN MAX UNIT 270 mV – 270 mV NOTE 11: VSB is the self-bias voltage of the input FRCVP and FRCVN. 10 Base-T transmitter drive characteristics (FXMTP, FXMTN) JEDEC SYMBOL PARAMETER VSLW VO(CM) Differential voltage at specified slew rate VO(DIFF) VO(I) Differential voltage output Common-mode output voltage Output idle differential voltage VOD(SLEW) VOC VOD VOD(IDLE) TEST CONDITIONS See Figure 3 (d) and 3 (e) Into open circuit IO(FC) Output current, fault condition‡ ‡ Assured by design IO(FC) 14 • HOUSTON, TEXAS 77251–1443 POST OFFICE BOX 1443 MIN MAX UNIT "2.2 "2.8 V 0 4 V 5.25 V "50 mV 300 mA ThunderLAN TNETE100 PCI ETHERNET CONTROLLER SINGLE-CHIP 10 BASE-T WITH MII FOR 100 BASE-T/100VG-AnyLAN SPWS017B – APRIL 1995 – REVISED AUGUST 1996 electrical characteristics over recommended ranges of supply voltage (unless otherwise noted) (physical interface pins) (continued) AUI receiver input (ARCVP, ARCVN, ACOLP, ACOLN) JEDEC SYMBOL PARAMETER VSQ– TEST CONDITIONS Falling input pair squelch threshold MIN MAX – 325 UNIT mV AUI transmitter drive characteristics (AXMTP, AXMTN) JEDEC SYMBOL PARAMETER VO(DIFF)1 Differential output voltage VOD(1) VOI(DIFF) Output idle differential voltage† VOD(IDLE) VOI(DIFF)U Output differential undershoot‡ TEST CONDITIONS See Note 12 MIN MAX "500 "1315 "40† UNIT mV mV 100‡ mV 150‡ mA MIN MAX UNIT VOD(IDLE)U IO(FC) Output current, fault condition ‡ IO(FC) † Assured by design ‡ Characterized but not tested NOTE 12: The differential voltage is measured as per Figure 3(b) on page 17. crystal oscillator characteristics JEDEC SYMBOL PARAMETER VSB(FXTL1) Input self-bias voltage TEST CONDITIONS VIB IOH(FXTL2) High-level output current (see Note 4) IOH V(FXTL2) = VSB(FXTL1) V(FXTL1) = VSB(FXTL1) + 0.5 V IOL(FXTL2) Low-level output current IOL V(FXTL2) = VSB(FXTL1) V(FXTL1) = VSB(FXTL1) – 0.5 V 1.7 2.8 V – 1.3 –5 mA 0.4 1.5 mA NOTE 4: The algebraic convention, where the more negative (less positive) limit is designated as a minimum, is used for logic-voltage levels only. POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443 15 ThunderLAN TNETE100 PCI ETHERNET CONTROLLER SINGLE-CHIP 10 BASE-T WITH MII FOR 100 BASE-T/100VG-AnyLAN SPWS017B – APRIL 1995 – REVISED AUGUST 1996 PARAMETER MEASUREMENT INFORMATION Outputs are driven to a minimum high-logic level of 2.4 V and to a maximum low-logic level of 0.6 V. These levels are compatible with TTL devices. Output transition times are specified as follows: For a high-to-low transition on either an input or output signal, the level at which the signal is said to be no longer high is 2 V and the level at which the signal is said to be low is 0.8 V. For a low-to-high transition, the level at which the signal is said to be no longer low is 0.8 V and the level at which the signal is said to be high is 2 V, as shown below. The rise and fall times are not specified but are assumed to be those of standard TTL devices, which are typically 1.5 ns. 2 V (high) 0.8 V (low) test measurement The test-load circuit shown in Figure 3 represents the programmable load of the tester pin electronics that are used to verify timing parameters of the TNETE100 output signals. 16 POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443 ThunderLAN TNETE100 PCI ETHERNET CONTROLLER SINGLE-CHIP 10 BASE-T WITH MII FOR 100 BASE-T/100VG-AnyLAN SPWS017B – APRIL 1995 – REVISED AUGUST 1996 IOL 50 Ω Test Point AXMTP Test Point VLOAD CL TTL Output Under Test 50 Ω 78 Ω AXMTN X1 IOH (b) AXMTP AND AXMTN TEST LOAD (AC TESTING) X1 – Fil – Mag 23Z90 (1:1) (a) TTL OUTPUT TEST LOAD 50 Ω 25 Ω Test Point FXMTP 50 Ω FIREF 25 Ω 180 Ω FXMTN X2 (d) FXMTP AND FXMTN TEST LOAD (AC TESTING) X2 – Fil – Mag 23Z128 (1: √2) (c) FIREF TEST CIRCUIT 50 Ω Test Point FXMTP 50 Ω 50 Ω Test Point FXMTN 50 Ω (e) FXMTP AND FXMTN TEST LOAD (DC TESTING) Where: IOL IOH VLOAD CL = Refer to IOL in recommended operating conditions = Refer to IOH in recommended operating conditions = 1.5 V, typical dc-level verification or 0.7 V, typical timing verification = 18 pF, typical load-circuit capacitance Figure 3. Test and Load Circuit POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443 17 ThunderLAN TNETE100 PCI ETHERNET CONTROLLER SINGLE-CHIP 10 BASE-T WITH MII FOR 100 BASE-T/100VG-AnyLAN SPWS017B – APRIL 1995 – REVISED AUGUST 1996 switching characteristics for PCI 5-V and 3.3-V (see Note 13 and Figure 4) PARAMETER tVAL Delay time, PCLK to bused signals valid (see Notes 14 and 15) tVAL(PTP) Delay time, PCLK to bused signals valid point-to-point (see Notes 14 and 15) ton Float to active delay MIN MAX 2 11 ns 2 12 ns 2 UNIT ns toff Active to float delay 28 ns NOTES: 13. Some of the timing symbols in this table are not currently listed with EIA or JEDEC standards for semiconductor symbology but are consistent with the PCI Local-Bus Specification, Revision 2.0. 14. Minimum times are measured with a 0-pF equivalent load; maximum times are measured with a 50-pF equivalent load. Actual test capacitance may vary, but results should be correlated to these specifications. 15. PREQ and PGNT are point-to-point signals and have different output valid delay and input setup times than do bused signals. PGNT has a setup time of 10 ns; PREQ has a setup time of 12 ns. All other signals are bused. timing requirements for PCI 5-V and 3.3-V (see Note 13 and Figure 4) MIN tsu tsu(PTP) Setup time, bused signals valid to PCLK (see Note 15) th Input hold time from PCLK Setup time to PCLK—point-to-point (see Note 15) MAX UNIT 7 ns 10, 12 ns 0 100 Mbps 30 10 Mbps 30 ns 50† 500† ns tc Cycle time, time PCLK (see Note 16) tw(H) tw(L) Pulse duration, PCLK high 12 ns Pulse duration, PCLK low 12 ns ns tslew Slew rate, PCLK (see Note 17) 1 4 V/ns † Characterized by design and system specifications. NOTES: 13. Some of the timing symbols in this table are not currently listed with EIA or JEDEC standards for semiconductor symbology but are consistent with the PCI Local-Bus Specification, Revision 2.0. 15. PREQ and PGNT are point-to-point signals and have different output valid delay and input setup times than do bused signals. PGNT has a setup time of 10 ns; PREQ has a setup time of 12 ns. All other signals are bused. 16. As a requirement for frame transmission /reception, the minimum PCLK frequency varies with network speed. The clock can only be stopped in a low state. 17. Rise and fall times are specified in terms of the edge rate measured in V/ns. This slew rate must be met across the minimum peak-to-peak portion of the clock waveform. 18 POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443 ThunderLAN TNETE100 PCI ETHERNET CONTROLLER SINGLE-CHIP 10 BASE-T WITH MII FOR 100 BASE-T/100VG-AnyLAN SPWS017B – APRIL 1995 – REVISED AUGUST 1996 timing requirements for PCI 5-V and 3.3-V (continued) 2V 1.5 V 0.8 V 5-V Clock tc tw(H) tw(L) 0.475 × VDD 0.4 × VDD 0.325 × VDD 3.3-V Clock tVAL Output Delay 3-State Output ton toff th tsu Inputs Valid Input Vmax Figure 4. PCI 5-V and 3.3-V Timing POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443 19 ThunderLAN TNETE100 PCI ETHERNET CONTROLLER SINGLE-CHIP 10 BASE-T WITH MII FOR 100 BASE-T/100VG-AnyLAN SPWS017B – APRIL 1995 – REVISED AUGUST 1996 timing requirements for MII receive (see Figure 5)† MIN tsu(MRX pins) th(MRX pins) MAX UNIT Setup time, MRXD[3:0], MRXDV, MRXER (see Note 18) 10 ns Hold time, MTX[3:0], MRXDV, MRXER (see Note 18) 10 ns switching characteristics for MII transmit (see Figure 5)† PARAMETER MIN MAX UNIT td(MTX pins) Delay time, MTCLK to MTXD[3:0], MTXEN, and MTXER outputs (see Note 19) 0 25 ns † Both MCRS and MCOL are driven asynchronously by the PHY. NOTES: 18. MRXD[3:0] is driven by the PHY on the falling edge of MRCLK. It is sampled by the reconciliation sublayer synchronous to the edge of MRCLK. MRXD[3:0] timing must be met during clock periods where MRXDV is asserted. MRXDV is asserted and deasserted by the PHY on the falling edge of MRCLK. It is sampled by the reconciliation sublayer synchronous to the rising edge of MRCLK. MRXER is driven by the PHY on the falling edge of MRCLK. It is sampled by the reconciliation sublayer synchronous to the rising edge of MRCLK. MRXER timing must be met during clock periods when MRXDV is asserted. 19. MTXD[3:0] is driven by the reconciliation sublayer synchronous to the MTCLK. MTXEN is asserted and deasserted by the reconciliation sublayer synchronous to the MTCLK rising edge. MTXER is driven synchronous to the rising edge of MTCLK. MTCLK MTXD[3:0], MTXEN, MTXER td(MTX pins) MRCLK MRXD[3:0], MRXDV, MRXER tsu(MRX pins) th(MRX pins) Figure 5. MII Transmit and Receive Timing 20 POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443 ThunderLAN TNETE100 PCI ETHERNET CONTROLLER SINGLE-CHIP 10 BASE-T WITH MII FOR 100 BASE-T/100VG-AnyLAN SPWS017B – APRIL 1995 – REVISED AUGUST 1996 timing requirements for MDIO (see Figure 6) ta(MDCLKH-MDIOV) Access time, MDIO valid from MDCLK high (see Note 20) MIN MAX UNIT 0 300 ns MIN MAX UNIT switching characteristics for MDIO (see Figure 7) PARAMETER td(MDIOV-MDCLKH) td(MDCLKH-MDIOX) Delay time, MDIO valid to MDCLK high (see Note 21) 10 ns Delay time, MDCLK high to MDIO changing (see Note 21) 10 ns NOTES: 20. When the MDIO signal is sourced by the PMI /PHY, it is sampled by TNETE100 synchronous to the rising edge of MDCLK. 21. MDIO is a bidirectional signal that can be sourced by TNETE100 or the PMI /PHY. When TNETE100 sources the MDIO signal, TNETE100 asserts MDIO synchronous to the rising edge of MDCLK. MDCLK MDIO ta(MDCLKH-MDIOV) Figure 6. Management Data I/O Timing (Sourced by PHY) MDCLK MDIO td(MDIOV-MDCLKH) td(MDCLKH-MDIOX) Figure 7. Management Data I/O Timing (Sourced by TNETE100) POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443 21 ThunderLAN TNETE100 PCI ETHERNET CONTROLLER SINGLE-CHIP 10 BASE-T WITH MII FOR 100 BASE-T/100VG-AnyLAN SPWS017B – APRIL 1995 – REVISED AUGUST 1996 timing requirements for BIOS ROM and LED interface (see Figure 8)† MIN tsu th Setup time, data Hold time, data MAX UNIT 250 ns 0 ns switching characteristics for BIOS ROM and LED interface (see Figure 8)† PARAMETER MIN MAX UNIT td(EADV-EXLEL) Delay time, address high byte valid to EXLE low (address high byte setup time for external latch) 0 ns td(EXLEL-EADZ) Delay time, EXLE low to address high byte invalid (address high byte hold time for external latch) 10 ns Delay time, address low byte valid to EALE low (address low byte setup time for external latch) 0 ns Delay time, EALE low to address low byte invalid (address low byte hold time for external latch) 10 ns ta Access time, address 288 † The EPROM interface, consisting of 11 pins, requires only two TTL ’373 latches to latch the high and low addresses. ns td(EADV-EALEL) td(EALEL-EADZ) EAD[7:0] High Address Low Address Data td(EADV-EXLEL) td(EADV-EALEL) td(EXLEL-EADZ) td(EALEL-EADZ) EXLE EALE ta EOE tsu Figure 8. BIOS ROM and LED Interface Timing 22 POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443 th ThunderLAN TNETE100 PCI ETHERNET CONTROLLER SINGLE-CHIP 10 BASE-T WITH MII FOR 100 BASE-T/100VG-AnyLAN SPWS017B – APRIL 1995 – REVISED AUGUST 1996 switching characteristics for configuration EEPROM interface (see Figure 9) PARAMETER MIN MAX UNIT 0 100 kHz EDCLK low to EDIO data in valid 0.3 3.5 µs Time the bus must be free before a new transmission can start 4.7 µs 4 µs 4.7 µs fCLK(EDCLK) td(EDCLKL-EDIOV) Clock frequency, EDCLK td(EDIO free) td(EDIOV-EDCLKL) tw(L) tw(H) Low period, clock High period, clock 4 µs td(EDCLKH-EDIOV) td(EDCLKL-EDIOX) Delay time, EDCLK high to EDIO valid (start condition setup time) 4.7 µs 0 µs td(EDIOV-EDCLKH) tr Delay time, EDIO valid to EDCLK high (data out setup time) 250 ns tf td(EDCLKH-EDIOH) Fall time, EDIO and EDCLK Delay time, EDCLK high to EDIO high (stop condition setup time) 4.7 µs td(EDCLKL-EDIOX) Delay time, EDCLK low to EDIO changing (data in hold time) 300 ns Delay time, EDIO valid after EDCLK low (start condition hold time for EEPROM) Delay time, EDCLK low to EDIO changing (data out hold time) Rise time, EDIO and EDCLK tf tw(H) 1 µs 300 ns tr tw(L) EDCLK td(EDCLKL-EDIOX) td(EDCLKH-EDIOV) td(EDCLKH-EDIOH) td(EDIOV-EDCLKL) td(EDIOV-EDCLKH) EDIO (OUT) td(EDIO free) td(EDCLKL-EDIOX) td(EDCLKL-EDIOV) EDIO (IN) Figure 9. Configuration EEPROM Interface Timing POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443 23 ThunderLAN TNETE100 PCI ETHERNET CONTROLLER SINGLE-CHIP 10 BASE-T WITH MII FOR 100 BASE-T/100VG-AnyLAN SPWS017B – APRIL 1995 – REVISED AUGUST 1996 timing requirements for crystal oscillator (see Figure 10)† MIN td(VDDH–FXTL1V) TYP Delay time from minimum VDD high level to first valid FXTL1V full swing period (see Note 22) tw(H) tw(L) Pulse duration at FXTL1 high 13 Pulse duration at FXTL1 low 13 tt tc Transition time of FXTL1 Cycle time, FXTL1 UNIT 100 ms ns ns 7 ns 50 ns "0.01 Tolerance of FXTL1 input frequency MAX % † The FXTL signal may be implemented by either connecting a 20-MHz crystal across the FXTL1 and FXTL2 pins or by driving the FXTL1 from a 20-MHz crystal oscillator module. NOTE 22: This specification is provided as an aid to board design. This specification is not guaranteed during manufacturing testing. Minimum VDD High Level VDD tc tw(H) td(VDDH–FXTL1V) tt FXTL1 tw(L) Figure 10. Crystal Oscillator Timing 24 POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443 tt ThunderLAN TNETE100 PCI ETHERNET CONTROLLER SINGLE-CHIP 10 BASE-T WITH MII FOR 100 BASE-T/100VG-AnyLAN SPWS017B – APRIL 1995 – REVISED AUGUST 1996 MECHANICAL DATA PCE (S-PQFP-G***) PLASTIC QUAD FLATPACK 144 PIN SHOWN 108 73 109 NO. OF PINS*** A 144 22,75 TYP 160 25,35 TYP 72 0,38 0,22 0,13 M 0,65 37 144 1 0,16 NOM 36 Gage Plane A 28,20 SQ 27,80 31,45 SQ 30,95 0,25 0,25 MIN 0°– 7° 1,03 0,73 3,60 3,20 Seating Plane 0,10 4,10 MAX 4040237 / B 10/94 NOTES: A. B. C. D. E. All linear dimensions are in millimeters. This drawing is subject to change without notice. Thermally enhanced molded plastic package with a heat spreader (HSP) Falls within JEDEC MS-022 The 144 PCE is identical to the 160 PCE except that four leads per corner are removed. POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443 25 IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER’S RISK. In order to minimize risks associated with the customer’s applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI’s publication of information regarding any third party’s products or services does not constitute TI’s approval, warranty or endorsement thereof. Copyright 1998, Texas Instruments Incorporated