TI TPS76333DBVR

 www.ti.com
SLVS181H − DECEMBER 1998 − REVISED JANUARY 2004
D 150-mA Low-Dropout Regulator
D Output Voltage: 5 V, 3.8 V, 3.3 V, 3.0 V, 2.8 V,
DBV PACKAGE
(TOP VIEW)
2.7 V, 2.5 V, 1.8 V, 1.6 V and Variable
D Dropout Voltage, Typically 300 mV
D
D
D
D
D
at 150 mA
Thermal Protection
Over Current Limitation
Less Than 2-µA Quiescent Current in
Shutdown Mode
−40°C to 125°C Operating Junction
Temperature Range
5-Pin SOT-23 (DBV) Package
IN
1
GND
2
EN
3
5
OUT
4
NC/FB
description
The TPS763xx family of low-dropout (LDO) voltage regulators offers the benefits of low-dropout voltage, low-power
operation, and miniaturized packaging. These regulators feature low dropout voltages and quiescent currents compared
to conventional LDO regulators. Offered in a 5-terminal, small outline integrated-circuit SOT-23 package, the TPS763xx
series devices are ideal for cost-sensitive designs and for applications where board space is at a premium.
A combination of new circuit design and process innovation has enabled the usual pnp pass transistor to be replaced by
a PMOS pass element. Because the PMOS pass element behaves as a low-value resistor, the dropout voltage is very
low—typically 300 mV at 150 mA of load current (TPS76333)—and is directly proportional to the load current. Since the
PMOS pass element is a voltage-driven device, the quiescent current is very low (140 µA maximum) and is stable over
the entire range of output load current (0 mA to 150 mA). Intended for use in portable systems such as laptops and cellular
phones, the low-dropout voltage feature and low-power operation result in a significant increase in system battery operating
life.
The TPS763xx also features a logic-enabled sleep mode to shut down the regulator, reducing quiescent current to 1 µA
maximum at TJ = 25°C.The TPS763xx is offered in 1.6-V,1.8-V, 2.5-V, 2.7-V, 2.8-V, 3.0-V, 3.3-V, 3.8-V, and 5-V fixed-voltage
versions and in a variable version (programmable over the range of 1.5 V to 6.5 V.
AVAILABLE OPTIONS
TJ
VOLTAGE
PACKAGE
PART NUMBER
SYMBOL
Variable
TPS76301DBVT(1)
TPS76301DBVR(2)
PAZI
1.6 V
TPS76316DBVT
TPS76316DBVR
PBHI
1.8 V
TPS76318DBVT
TPS76318DBVR
PBAI
2.5 V
TPS76325DBVT
TPS76325DBVR
PBBI
2.7 V
TPS76327DBVT
TPS76327DBVR
PBCI
TPS76328DBVT
TPS76328DBVR
PBDI
3.0 V
TPS76330DBVT
TPS76330DBVR
PBII
3.3 V
TPS76333DBVT
TPS76333DBVR
PBEI
3.8 V
TPS76338DBVT
TPS76338DBVR
PBFI
5.0 V
TPS76350DBVT
(1) The DBVT passive indicates tape and reel of 250 parts.
(2) The DBVR passive indicates tape and reel of 3000 parts.
TPS76350DBVR
PBGI
−40°C to 125°C
2.8 V
SOT-23
(DBV)
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
!" # $%&" !# '%()$!" *!"&+ *%$"#
$ " #'&$$!"# '& ",& "&# &-!# #"%&"# #"!*!* .!!"/+
*%$" '$&##0 *&# " &$&##!)/ $)%*& "&#"0 !)) '!!&"&#+
Copyright  2001 − 2004 Texas Instruments Incorporated
www.ti.com
SLVS181H − DECEMBER 1998 − REVISED JANUARY 2004
FUNCTIONAL BLOCK DIAGRAM
TPS76301
OUT
IN
EN
Current Limit/
Thermal
Protection
VREF
FB
GND
TPS76316/ 18/ 25/ 27/ 28/ 30/ 33/ 38/ 50
OUT
IN
EN
Current Limit/
Thermal
Protection
VREF
GND
Terminal Functions
TERMINAL
DESCRIPTION
NAME
GND
Ground
EN
Enable input
FB
Feedback voltage (TPS76301 only)
IN
Input supply voltage
NC
No connection (fixed-voltage option only)
OUT
Regulated output voltage
2
www.ti.com
SLVS181H − DECEMBER 1998 − REVISED JANUARY 2004
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)1
Input voltage range(2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to 10 V
Voltage range at EN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to VI + 0.3 V
Voltage on OUT, FB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Peak output current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Internally limited
ESD rating, HBM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 kV
Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Tables
Operating junction temperature range, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −40°C to 150°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C
(1) Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only,
and functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) All voltage values are with respect to network ground terminal.
DISSIPATION RATING TABLE
BOARD
PACKAGE
RθJC
RθJA
DERATING FACTOR
ABOVE TA = 25°C
TA ≤ 25°C
POWER RATING
TA = 70°C
POWER RATING
TA = 85°C
POWER RATING
Low K(1)
DBV
65.8 °C/W
259 °C/W
3.9 mW/°C
386 mW
212 mW
154 mW
High K(2)
DBV
65.8 °C/W
180 °C/W
5.6 mW/°C
555 mW
305 mW
222 mW
(1) The JEDEC Low K (1s) board design used to derive this data was a 3 inch x 3 inch, two layer board with 2 ounce copper traces on top of the
board.
(2) The JEDEC High K (2s2p) board design used to derive this data was a 3 inch x 3 inch, multilayer board with 1 ounce internal power and ground
planes and 2 ounce copper traces on top and bottom of the board.
recommended operating conditions
MIN
Input voltage, VI(1)
Continuous output current, IO
Operating junction temperature, TJ
NOM
MAX
UNIT
2.7
10
V
0
150
mA
−40
125
°C
(1) To calculate the minimum input voltage for your maximum output current, use the following equation:
VI(min) = VO(max) + VDO(max load)
3
www.ti.com
SLVS181H − DECEMBER 1998 − REVISED JANUARY 2004
electrical characteristics over recommended operating free-air temperature range,
VI = VO(typ) + 1 V, IO = 1 mA, EN = IN, Co = 4.7 µF (unless otherwise noted)
PARAMETER
TEST CONDITIONS
3.25 V > VI ≥ 2.7 V,
2.5 V ≥ VO ≥ 1.5 V,
3.25 V > VI ≥ 2.7 V,
2.5 V ≥ VO ≥ 1.5 V
TPS76301
VI ≥ 3.25 V,
5 V ≥ VO ≥ 1.5 V
VI ≥ 3.25 V,
5 V ≥ VO ≥ 1.5 V
VI ≥ 3.25 V,
5 V ≥ VO ≥ 1.5 V
VI ≥ 3.25 V,
5 V ≥ VO ≥ 1.5 V
VI = 2.7 V,
VI = 2.7 V,
TPS76316
VI = 3.25 V,
VI = 3.25 V,
VI = 3.25 V,
VI = 3.25 V,
VI = 2.7 V,
VI = 2.7 V,
VO
Output voltage
TPS76318
VI = 3.25 V,
VI = 3.25 V,
VI = 3.25 V,
VI = 3.25 V,
IO = 1 mA to 100 mA,
TPS76325
IO = 1 mA to 100 mA
IO = 1 mA to 150 mA,
IO = 1 mA to 150 mA
IO = 1 mA to 100 mA,
TPS76327
TPS76328
TPS76330
IO = 1 mA to 100 mA,
TJ = 25°C
IO = 1 mA to 100 mA,
IO = 1 mA to 150 mA,
TJ = 25°C
IO = 1 mA to 150 mA,
1 mA< IO < 75 mA,
TJ = 25°C
1 mA< IO < 75 mA
1 mA < IO < 100 mA,
TJ = 25°C
1 mA < IO < 100 mA
1 mA < IO < 150 mA,
TJ = 25°C
1 mA < IO < 150 mA
1 mA< IO < 75 mA,
TJ = 25°C
1 mA< IO < 75 mA
1 mA < IO < 100 mA,
TJ = 25°C
1 mA < IO < 100 mA
1 mA < IO < 150 mA,
TJ = 25°C
1 mA < IO < 150 mA
TJ = 25°C
TJ = 25°C
TJ = 25°C
IO = 1 mA to 100 mA
IO = 1 mA to 150 mA,
TJ = 25°C
IO = 1 mA to 150 mA
IO = 1 mA to 100 mA,
TJ = 25°C
TYP
MAX
0.98 VO
VO
1.02 VO
0.97 VO
VO
1.03 VO
0.98 VO
VO
1.02 VO
0.97 VO
VO
1.03 VO
0.975 VO
VO
1.025 VO
0.9625 VO
VO
1.0375 VO
1.568
1.6
1.632
1.552
1.6
1.648
1.568
1.6
1.632
1.552
1.6
1.648
1.560
1.6
1.640
1.536
1.6
1.664
1.764
1.8
1.836
1.746
1.8
1.854
1.764
1.8
1.836
1.746
1.8
1.854
1.755
1.8
1.845
1.733
1.8
1.867
2.45
2.5
2.55
2.425
2.5
2.575
2.438
2.5
2.562
2.407
2.5
2.593
2.646
2.7
2.754
2.619
2.7
2.781
2.632
2.7
2.767
2.599
2.7
2.801
2.744
2.8
2.856
2.716
2.8
2.884
2.73
2.8
2.87
UNIT
V
V
V
IO = 1 mA to 100 mA
IO = 1 mA to 150 mA,
TJ = 25°C
IO = 1 mA to 150 mA
IO = 1 mA to 100 mA,
2.695
2.8
2.905
TJ = 25°C
2.94
3.0
3.06
IO = 1 mA to 100 mA
IO = 1 mA to 150 mA,
2.91
3.0
3.09
TJ = 25°C
2.925
3.0
3.075
2.888
3.0
3.112
IO = 1 mA to 150 mA
4
IO = 1 mA to 75 mA,
TJ = 25°C
IO = 1 mA to 75 mA,
MIN
V
V
V
V
www.ti.com
SLVS181H − DECEMBER 1998 − REVISED JANUARY 2004
electrical characteristics over recommended operating free-air temperature range,
VI = VO(typ) + 1 V, IO = 1 mA, EN = IN, Co = 4.7 µF (unless otherwise noted) (continued)
PARAMETER
TEST CONDITIONS
TPS76333
VO
Output voltage
TPS76338
TPS76350
I(Q)
Quiescent current
(GND terminal current)
Standby current
3.3
3.366
3.201
3.3
3.399
3.218
3.3
3.382
3.177
3.3
3.423
3.724
3.8
3.876
3.705
3.8
3.895
3.686
3.8
3.914
3.667
3.8
3.933
4.875
5
5.125
4.825
5
5.175
4.750
5
5.15
TJ = 25°C
IO = 1 mA to 100 mA,
IO = 1 mA to 100 mA
TJ = 25°C
IO = 1 mA to 150 mA,
IO = 1 mA to 150 mA
TJ = 25°C
IO = 1 mA to 100 mA,
IO = 1 mA to 100 mA
TJ = 25°C
IO = 1 mA to 150 mA,
IO = 1 mA to 150 mA
TJ = 25°C
5
5.20
IO = 0 to 150 mA,
IO = 0 to 150 mA
TJ = 25°C (1)
(2)
85
100
EN < 0.5 V,
TJ = 25°C
0.5
4.80
140
EN < 0.5 V
1
UNIT
V
V
V
µA
A
2
f = 1 kHz, Co = 10 µF,
TJ = 25°C
TJ = 25°C (2)
(3)
Output voltage line regulation
(∆VO/VO) (see Note 3)
VO + 1 V < VI ≤ 10 V,
VO + 1 V < VI ≤ 10 V,
VI ≥ 3.5 V, TJ = 25°C
VI ≥ 3.5 V
VIH
VIL
EN high level input
(2)
EN low level input
(2)
II
EN input current
Ripple rejection
3.234
IO = 1 mA to 150 mA,
IO = 1 mA to 150 mA
Current limit
PSRR
MAX
TJ = 25°C
Co = 10 µF (2)
Output noise voltage
TYP
IO = 1 mA to 100 mA,
IO = 1 mA to 100 mA
BW = 300 Hz to 50 kHz,
TJ = 25°C,
Vn
MIN
µV
140
60
0.5
dB
0.8
1.5
0.04
0.07
0.1
1.4
0.5
A
%/V
2
V
1.2
EN = 0 V
−0.01
−0.5
EN = IN
−0.01
−0.5
A
µA
(1) Minimum IN operating voltage is 2.7 V or VO(typ) + 1 V, whichever is greater.
(2) Test condition includes, output voltage VO=0 volts (for variable device FB is shorted to VO), and pulse duration = 10 mS.
(3) If VO < 2.5 V and VImax = 10 V, VImin = 3.5 V:
Line Reg. (mV) + ǒ%ńVǓ
V
O
100
If VO > 2.5 V and VImax = 10 V, VImin = VO + 1 V:
Line Reg. (mV) + ǒ%ńVǓ
ǒVImax * 3.5 VǓ
V
O
1000
ǒVImax * ǒVO ) 1ǓǓ
100
1000
5
www.ti.com
SLVS181H − DECEMBER 1998 − REVISED JANUARY 2004
electrical characteristics over recommended operating free-air temperature range,
VI = VO(typ) + 1 V, IO = 1 mA, EN = IN, Co = 4.7 µF (unless otherwise noted) (continued)
PARAMETER
TEST CONDITIONS
TPS76325
VDO
Dropout voltage
TPS76333
TPS76350
6
MIN
TYP
IO = 0 mA,
IO = 1 mA,
TJ = 25°C
TJ = 25°C
0.2
IO = 50 mA,
IO = 50 mA
TJ = 25°C
120
IO = 75 mA,
IO = 75 mA
TJ = 25°C
180
IO = 100 mA,
IO = 100 mA
TJ = 25°C
IO = 150 mA,
IO = 150 mA
TJ = 25°C
360
IO = 0 mA,
IO = 1 mA,
TJ = 25°C
TJ = 25°C
0.2
IO = 50 mA,
IO = 50 mA
TJ = 25°C
100
IO = 75 mA,
IO = 75 mA
TJ = 25°C
150
IO = 100 mA,
IO = 100 mA
TJ = 25°C
200
IO = 150 mA,
IO = 150 mA
TJ = 25°C
300
IO = 0 mA,
IO = 1 mA,
TJ = 25°C
TJ = 25°C
0.2
IO = 50 mA,
IO = 50 mA
TJ = 25°C
60
IO = 75 mA,
IO = 75 mA
TJ = 25°C
IO = 100 mA,
IO = 100 mA
TJ = 25°C
120
IO = 150 mA,
IO = 150 mA
TJ = 25°C
180
MAX
UNIT
3
150
200
225
300
240
mV
300
400
450
600
3
125
166
188
250
mV
250
333
375
500
2
75
100
90
113
150
150
200
225
300
mV
www.ti.com
SLVS181H − DECEMBER 1998 − REVISED JANUARY 2004
TYPICAL CHARACTERISTICS
TPS76325
TPS76318
OUTPUT VOLTAGE
vs
OUTPUT CURRENT
OUTPUT VOLTAGE
vs
OUTPUT CURRENT
2.505
VI = 3.5 V
CI = CO = 4.7 µF
TJ = 25°C
1.800
VO − Output Voltage − V
2.5
VO − Output Voltage − V
1.805
VI = 3.5 V
CI = CO = 4.7 µF
TJ = 25°C
2.495
2.49
2.485
1.795
1.790
1.785
1.780
2.48
1.775
2.475
0
30
60
90
120
150
180
1.770
0
IO − Output Current − mA
30
60
Figure 1
120
150
180
Figure 2
TPS76350
TPS76325
OUTPUT VOLTAGE
vs
OUTPUT CURRENT
OUTPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
5.01
2.53
VI = 6 V
CI = CO = 4.7 µF
TJ = 25°C
VI = 3.5 V
CI = CO = 4.7 µF
2.52
VO − Output Voltage − V
5
VO− Output Voltage − V
90
IO − Output Current − mA
4.99
4.98
4.97
4.96
2.51
IO = 1 mA
2.5
2.49
IO = 150 mA
2.48
4.95
0
30
60
90
120
IO − Output Current − mA
Figure 3
150
180
2.47
−55 −35
−15
5
25
45
65
85
105
125
TJ − Junction Temperature − °C
Figure 4
7
www.ti.com
SLVS181H − DECEMBER 1998 − REVISED JANUARY 2004
TYPICAL CHARACTERISTICS
TPS76318
TPS76350
OUTPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
OUTPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
5.1
1.82
VI = 6 V
CI = CO = 4.7 µF
5.08
1.81
IO = 1 mA
5.06
VO − Output Voltage − V
VO − Output Voltage − V
1.8
1.79
IO = 150 mA
1.78
1.77
1.76
5.04
5.02
IO = 1 mA
5
4.98
4.96
IO = 150 mA
4.94
VI = 3.5 V
CI = CO = 4.7 µF
1.75
1.74
−55 −35
−15
5
25
45
65
85
105
4.92
125
4.9
−55 −35
TJ − Junction Temperature − °C
−15
25
5
45
85
65
105
125
TJ − Junction Temperature − °C
Figure 5
Figure 6
TPS76350
OUTPUT NOISE
vs
FREQUENCY
GROUND CURRENT
vs
FREE-AIR TEMPERATURE
3 mV ǸHz
1000
TJ = 25°C
Ground Current − µ A
VI = 6 V
CI = CO = 4.7 µF
IO = 0 mA and 150 mA
2.5 mV ǸHz
2 mV ǸHz
1 mV ǸHz
10
−55 −35
CO = 4.7 µF
IO = 150 mA
1.5 mV ǸHz
100
0.5 mV ǸHz
−15
5
25
45
65
85
TJ − Junction Temperature − °C
Figure 7
8
CO = 10 µF
IO = 150 mA
105
125
0 mV ǸHz
250
CO = 4.7 µF
IO = 1 mA
CO = 10 µF
IO = 1 mA
1k
10k
f − Frequency − Hz
Figure 8
100k
www.ti.com
SLVS181H − DECEMBER 1998 − REVISED JANUARY 2004
TYPICAL CHARACTERISTICS
TPS76325
DROPOUT VOLTAGE
vs
FREE-AIR TEMPERATURE
OUTPUT IMPEDANCE
vs
FREQUENCY
600
10
VI = EN = 2.7 V
CI = CO = 4.7 µF
VDO − Dropout Voltage − mV
IO = 1 mA
1
IO = 150 mA
0.1
0.01
0.1
150 mA
400
300
200
1 mA
0 mA
100
CI = CO = 4.7 µF
ESR = 1 Ω
TJ = 25°C
1
10
100
0
−55 −35
1000
−15
5
25
45
65
85
105
125
TJ − Junction Temperature − °C
f − Frequency − kHz
Figure 9
Figure 10
TPS76325
RIPPLE REJECTION
vs
FREQUENCY
70
60
IO = 1 mA
50
Ripple Rejection − dB
Zo − Output Impedance − Ω
500
IO = 150 mA
40
30
20
10
0
−10
10
CO = 4.7 µF
ESR = 1 Ω
TJ = 25°C
100
1k
10 k
100 k
1M
10 M
f − Frequency − Hz
Figure 11
9
www.ti.com
SLVS181H − DECEMBER 1998 − REVISED JANUARY 2004
TYPICAL CHARACTERISTICS
4
3
2
∆ VO − Change in
Output Voltage − mV
200
100
0
CO = 4.7 µF
ESR = 0.25 Ω
TJ = 25°C
50
CO = 4.7 µF
ESR = 0.25 Ω
TJ = 25°C
1
TPS76318
LOAD TRANSIENT RESPONSE
I O − Output Current − mA
5
20
0
dv + 1 V
10 ms
dt
−20
−30
∆ VO − Change in
Output Voltage − mV
VI − Input Voltage − V
TPS76318
LINE TRANSIENT RESPONSE
0
−50
−100
−150
0
20
40
60
0
80 100 120 140 160 180 200
t − Time − µs
20
40
8
dv + 1 V
10 ms
dt
6
5
CO = 4.7 µF
ESR = 0.25 Ω
TJ = 25°C
∆ VO − Change in
Output Voltage − mV
50
0
−50
TPS76350
LOAD TRANSIENT RESPONSE
200
CO = 4.7 µF
ESR = 0.25 Ω
TJ = 25°C
100
0
150
100
0
−100
−200
−100
0
50
100 150 200 250 300 350 400 450 500
t − Time − µs
Figure 14
10
I O − Output Current − mA
TPS76350
LINE TRANSIENT RESPONSE
7
80 100 120 140 160 180 200
t − Time − µs
Figure 13
∆ VO − Change in
Output Voltage − mV
VI − Input Voltage − V
Figure 12
60
0
20
40
60
80 100 120 140 160 180 200
t − Time − µs
Figure 15
www.ti.com
SLVS181H − DECEMBER 1998 − REVISED JANUARY 2004
TYPICAL CHARACTERISTICS
TYPICAL REGIONS OF STABILITY
TYPICAL REGIONS OF STABILITY
COMPENSATION SERIES RESISTANCE (CSR)(1)
vs
OUTPUT CURRENT
COMPENSATION SERIES RESISTANCE (CSR)(1)
vs
ADDED CERAMIC CAPACITANCE
100
CSR − Compensation Series Resistance − Ω
CSR − Compensation Series Resistance − Ω
100
Region of Instability
10
CO = 4.7 µF
TJ = 25°C
1
0.1
Region of Instability
0.01
Region of Instability
10
I = 150 mA
CO = 4.7 µF
TJ = 25°C
1
0.1
Region of Instability
0.01
0
50
100
150
200
250
0
0.1
Figure 16
0.6 0.7 0.8
0.9
1
Figure 17
TYPICAL REGIONS OF STABILITY
TYPICAL REGIONS OF STABILITY
COMPENSATION SERIES RESISTANCE (CSR)(1)
vs
OUTPUT CURRENT
COMPENSATION SERIES RESISTANCE (CSR)(1)
vs
ADDED CERAMIC CAPACITANCE
100
CSR − Compensation Series Resistance − Ω
100
CSR − Compensation Series Resistance − Ω
0.2 0.3 0.4 0.5
Added Ceramic Capacitance − µF
IO − Output Current − mA
Region of Instability
10
CO = 10 µF
1
0.1
Region of Instability
0.01
0
50
100
150
IO − Output Current − mA
Figure 18
200
250
Region of Instability
10
CO = 10 µF
1
0.1
Region of Instability
0.01
0
0.1
0.2 0.3 0.4 0.5
0.6 0.7 0.8
0.9
1
Added Ceramic Capacitance − µF
Figure 19
(1) CSR refers to the total series resistance, including the ESR of the capacitor, any series resistance added externally, and PWB trace
resistance to CO.
11
www.ti.com
SLVS181H − DECEMBER 1998 − REVISED JANUARY 2004
APPLICATION INFORMATION
The TPS763xx low-dropout (LDO) regulators are new families of regulators which have been optimized for use in
battery-operated equipment and feature extremely low dropout voltages, low quiescent current (140 µA), and an enable
input to reduce supply currents to less than 2 µA when the regulator is turned off.
device operation
The TPS763xx uses a PMOS pass element to dramatically reduce both dropout voltage and supply current over more
conventional PNP pass element LDO designs. The PMOS pass element is a voltage-controlled device that, unlike a PNP
transistor, does not require increased drive current as output current increases. Supply current in the TPS763xx is
essentially constant from no-load to maximum load.
Current limiting and thermal protection prevent damage by excessive output current and/or power dissipation. The device
switches into a constant-current mode at approximately 1 A; further load reduces the output voltage instead of increasing
the output current. The thermal protection shuts the regulator off if the junction temperature rises above 165°C. Recovery
is automatic when the junction temperature drops approximately 25°C below the high temperature trip point. The PMOS
pass element includes a back diode that safely conducts reverse current when the input voltage level drops below the output
voltage level.
A logic low on the enable input, EN shuts off the output and reduces the supply current to less than 2 µA. EN should be
tied high in applications where the shutdown feature is not used.
A typical application circuit is shown in Figure 20.
TPS763xx(1)
VI
C1
1 µF
1
IN
NC/FB
OUT
4
5
VO
3
EN
+
GND
2
4.7 µF
CSR = 1 Ω
(1) TPS76316, TPS76318, TPS76325, TPS76327, TPS76328,
TPS7630 TPS76333, TPS76338, TPS76350 (fixed-voltage options).
Figure 20. Typical Application Circuit
12
www.ti.com
SLVS181H − DECEMBER 1998 − REVISED JANUARY 2004
APPLICATION INFORMATION
external capacitor requirements
Although not required, a 0.047 µF or larger ceramic bypass input capacitor, connected between IN and GND and located
close to the TPS763xx, is recommended to improve transient response and noise rejection. A higher-value electrolytic input
capacitor may be necessary if large, fast-rise-time load transients are anticipated and the device is located several inches
from the power source.
Like all low dropout regulators, the TPS763xx requires an output capacitor connected between OUT and GND to stabilize
the internal loop control. The minimum recommended capacitance value is 4.7 µF and the ESR (equivalent series
resistance) must be between 0.3 Ω and 10 Ω. Capacitor values 4.7 µF or larger are acceptable, provided the ESR is less
than 10 Ω. Solid tantalum electrolytic, aluminum electrolytic, and multilayer ceramic capacitors are all suitable, provided
they meet the requirements described above. Most of the commercially available 4.7 µF surface-mount solid tantalum
capacitors, including devices from Sprague, Kemet, and Nichico, meet the ESR requirements stated above.
CAPACITOR SELECTION
PART NO.
MAX ESR(1)
SIZE (H × L × W)†
MFR.
VALUE
T494B475K016AS
KEMET
4.7 µF
1.5 Ω
1.9 × 3.5 × 2.8
195D106x0016x2T
SPRAGUE
10 µF
1.5 Ω
1.3 × 7.0 × 2.7
695D106x003562T
SPRAGUE
10 µF
1.3 Ω
2.5 × 7.6 × 2.5
AVX
4.7 µF
0.6 Ω
2.6 × 6.0 × 3.2
TPSC475K035R0600
(1) Size is in mm. ESR is maximum resistance in ohms at 100 kHz and TA = 25°C. Listings are sorted by height.
output voltage programming
The output voltage of the TPS76301 adjustable regulator is programmed using an external resistor divider as shown in
Figure 21. The output voltage is calculated using:
V
O
+ 0.995
V
ǒ1 ) R1
Ǔ
R2
ref
(1)
Where:
Vref = 1.192 V typ (the internal reference voltage)
0.995 is a constant used to center the load regulator (1%)
Resistors R1 and R2 should be chosen for approximately 7-µA divider current. Lower value resistors can be used but offer
no inherent advantage and waste more power. Higher values should be avoided as leakage currents at FB increase the
output voltage error. The recommended design procedure is to choose R2 = 169 kΩ to set the divider current at 7 µA and
then calculate R1 using:
R1 +
ǒ
V
0.995
O
V
Ǔ
*1
ref
R2
(2)
13
www.ti.com
SLVS181H − DECEMBER 1998 − REVISED JANUARY 2004
APPLICATION INFORMATION
TPS76301
OUTPUT VOLTAGE
PROGRAMMING GUIDE
DIVIDER RESISTANCE
(kΩ)(1)
OUTPUT
VOLTAGE
(V)
R1
R2
2.5
187
169
3.3
301
169
3.6
348
169
4
402
169
549
169
750
6.45
(1) 1% values shown.
169
5
VI
1 µF
≥2 V
1
IN
OUT
3
≤ 0.5 V
5
VO
R1
EN
FB
GND
2
4
+
R2
4.7 µF
CSR = 1 Ω
Figure 21. TPS76301 Adjustable LDO Regulator Programming
power dissipation and junction temperature
Specified regulator operation is assured to a junction temperature of 125°C; the maximum junction temperature allowable
to avoid damaging the device is 150°C. This restriction limits the power dissipation the regulator can handle in any given
application. To ensure the junction temperature is within acceptable limits, calculate the maximum allowable dissipation,
PD(max), and the actual dissipation, PD, which must be less than or equal to PD(max).
The maximum-power-dissipation limit is determined using the following equation:
P
D(max)
T max * T
A
+ J
R
qJA
Where:
TJmax is the maximum allowable junction temperature
RθJA is the thermal resistance junction-to-ambient for the package, see the dissipation rating table.
TA is the ambient temperature.
The regulator dissipation is calculated using:
P
D
ǒ
Ǔ
+ V *V
I
O
I
O
Power dissipation resulting from quiescent current is negligible.
14
www.ti.com
SLVS181H − DECEMBER 1998 − REVISED JANUARY 2004
APPLICATION INFORMATION
regulator protection
The TPS763xx pass element has a built-in back diode that safely conducts reverse currents when the input voltage drops
below the output voltage (e.g., during power down). Current is conducted from the output to the input and is not internally
limited. If extended reverse voltage is anticipated, external limiting might be appropriate.
The TPS763xx also features internal current limiting and thermal protection. During normal operation, the TPS763xx limits
output current to approximately 800 mA. When current limiting engages, the output voltage scales back linearly until the
overcurrent condition ends. While current limiting is designed to prevent gross device failure, care should be taken not to
exceed the power dissipation ratings of the package. If the temperature of the device exceeds 165°C, thermal-protection
circuitry shuts it down. Once the device has cooled down to below 140°C, regulator operation resumes.
15
PACKAGE OPTION ADDENDUM
www.ti.com
8-Aug-2005
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
TPS76301DBVR
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS76301DBVRG4
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS76301DBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS76301DBVTG4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS76316DBVR
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS76316DBVRG4
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS76316DBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS76316DBVTG4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS76318DBVR
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS76318DBVRG4
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS76318DBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS76318DBVTG4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS76325DBVR
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS76325DBVRG4
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS76325DBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS76325DBVTG4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS76327DBV
OBSOLETE
SOT-23
DBV
5
TBD
Call TI
TPS76327DBVR
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS76327DBVRG4
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS76327DBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS76327DBVTG4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TBD
Lead/Ball Finish
Call TI
TPS76328DBV
OBSOLETE
SOT-23
DBV
5
TPS76328DBVR
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS76328DBVRG4
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS76328DBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS76328DBVTG4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
CU NIPDAU
Level-1-260C-UNLIM
Addendum-Page 1
Call TI
MSL Peak Temp (3)
Call TI
PACKAGE OPTION ADDENDUM
www.ti.com
8-Aug-2005
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
TPS76330DBV
OBSOLETE
SOT-23
DBV
5
TPS76330DBVR
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS76330DBVRG4
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS76330DBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS76330DBVTG4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS76333DBVR
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS76333DBVRG4
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS76333DBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS76333DBVTG4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS76338DBVR
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS76338DBVRG4
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS76338DBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS76338DBVTG4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS76350DBVR
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS76350DBVRG4
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS76350DBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS76350DBVTG4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
Lead/Ball Finish
MSL Peak Temp (3)
no Sb/Br)
TBD
Call TI
Call TI
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS) or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Addendum-Page 2
PACKAGE OPTION ADDENDUM
www.ti.com
8-Aug-2005
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 3
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
Telephony
www.ti.com/telephony
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address:
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright  2005, Texas Instruments Incorporated