NB4N11M 3.3 V 2.5 Gb/s Multi Level Clock/Data Input to CML Receiver/ Buffer/ Translator Description T h e N B 4 N 11 M i s a d i f f e r e n t i a l 1 −t o −2 c l o c k / d a t a distribution/translation chip with CML output structure, targeted for high−speed clock/data applications. The device is functionally equivalent to the EP11, LVEP11, SG11 or 7L11M devices. Device produces two identical differential output copies of clock or data signal operating up to 2.5 GHz or 2.5 Gb/s, respectively. As such, NB4N11M is ideal for SONET, GigE, Fiber Channel, Backplane and other clock/data distribution applications. Inputs accept LVPECL, CML, LVCMOS, LVTTL, or LVDS (See Table 5). The CML outputs are 16 mA open collector (See Figure 18) which requires resistor (RL) load path to VTT termination voltage. The open collector CML outputs must be terminated to VTT at power up. Differential outputs produces current–mode logic (CML) compatible levels when receiver loaded with 50 W or 25 W loads connected to 1.8 V, 2.5 V or 3.3 V supplies (see Figure 19). This simplifies device interface by eliminating a need for coupling capacitors. The device is offered in a small 8−pin TSSOP package. Application notes, models, and support documentation are available at www.onsemi.com. http://onsemi.com MARKING DIAGRAM* 8 1 TSSOP−8 DT SUFFIX CASE 948R 8 1 E11M ALYWG G A = Assembly Location L = Wafer Lot Y = Year W = Work Week G = Pb−Free Package (Note: Microdot may be in either location) *For additional marking information, refer to Application Note AND8002/D. Q0 Features • • • • • • • • • Q0 Maximum Input Clock Frequency > 2.5 GHz Maximum Input Data Rate > 2.5 Gb/s Typically 1 ps of RMS Clock Jitter Typically 10 ps of Data Dependent Jitter @ 2.5 Gb/s, RL = 25 W 420 ps Typical Propagation Delay 150 ps Typical Rise and Fall Times Operating Range: VCC = 3.0 V to 3.6 V with VEE = 0 V and VTT = 1.8 V to 3.6 V Functionally Compatible with Existing 2.5 V / 3.3 V LVEL, LVEP, EP, and SG Devices These are Pb−Free Devices* D D Q1 Q1 Figure 1. Functional Block Diagram ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 10 of this data sheet. *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. © Semiconductor Components Industries, LLC, 2005 November, 2005 − Rev. 1 1 Publication Order Number: NB4N11M/D NB4N11M Q0 1 8 VCC Q0 2 7 D Q1 3 6 D Q1 4 5 VEE Figure 2. Pinout (Top View) and Logic Diagram Table 1. Pin Description Pin Name I/O 1 Q0 CML Output Noninverted differential output. Typically receiver terminated with 50 W resistor to VTT. Open collector CML outputs must be terminated to VTT at powerup. Description 2 Q0 CML Output Inverted differential output. Typically receiver terminated with 50 W resistor to VTT. Open collector CML outputs must be terminated to VTT at powerup. 3 Q1 CML Output Noninverted differential output. Typically receiver terminated with 50 W resistor to VTT. Open collector CML outputs must be terminated to VTT at powerup. 4 Q1 CML Output Inverted differential output. Typically receiver terminated with 50 W resistor to VTT. Open collector CML outputs must be terminated to VTT at powerup. 5 VEE − Negative supply voltage. 6 D LVPECL, CML, HSTL, LVCMOS, LVDS, LVTTL Input Inverted differential input. 7 D LVPECL, CML, HSTL, LVCMOS, LVDS, LVTTL Input Noninverted differential input. 8 VCC − Positive supply voltage. http://onsemi.com 2 NB4N11M Table 2. ATTRIBUTES Characteristics Value ESD Protection Human Body Model Machine Model Moisture Sensitivity (Note 1) 8−TSSOP Flammability Rating Oxygen Index: 28 to 34 Transistor Count > 1000 V > 70 V Level 1 UL 94 V−0 @ 0.125 in 197 Meets or exceeds JEDEC Spec EIA/JESD78 IC Latchup Test 1. For additional information, see Application Note AND8003/D. Table 3. MAXIMUM RATINGS Symbol Rating Unit VCC Positive Power Supply Parameter VEE = −0.5 V Condition 1 Condition 2 4 V VEE Negative Power Supply VCC = +0.5 V −4 V VI Positive Input Negative Input VEE = 0 V VCC = 0 V 4 −4 V V VO Output Voltage VEE + 600 VCC + 400 mV mV TA Operating Temperature Range −40 to +85 °C Tstg Storage Temperature Range −65 to +150 °C qJA Thermal Resistance (Junction−to−Ambient) (Note 2) 0 lfpm 500 lfpm TSSOP−8 TSSOP−8 190 130 °C/W °C/W qJC Thermal Resistance (Junction−to−Case) 1S2P (Note 2) TSSOP−8 41 to 44 °C/W Tsol Wave Solder < 3 Sec @ 260°C 265 °C VI = VCC +0.4 V VI = VEE –0.4 V Minimum Maximum Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied, damage may occur and reliability may be affected. 2. JEDEC standard multilayer board − 1S2P (1 signal, 2 power) with 8 filled thermal vias under exposed pad. http://onsemi.com 3 NB4N11M Table 4. DC CHARACTERISTICS, CLOCK Inputs, CML Outputs VCC = 3.0 V to 3.6 V, VEE = 0 V, TA = −40°C to +85°C Characteristic Symbol ICC Min Power Supply Current (Inputs and Outputs Open) Typ Max Unit 25 35 mA RL = 50 W, VTT = 3.6 V to 2.5 V VOH Output HIGH Voltage (Note 3) VTT − 60 VTT − 10 VTT mV VOL Output LOW Voltage (Note 3) VTT − 1100 VTT − 800 VTT − 640 mV |VOD| Differential Output Voltage Magnitude 640 780 1000 mV RL = 25 W, VTT = 3.6 V to 2.5 V $5% VOH Output HIGH Voltage (Note 3) VTT − 60 VTT − 10 VTT mV VOL Output LOW Voltage (Note 3) VTT − 550 VTT − 400 VTT − 320 mV |VOD| Differential Output Voltage Magnitude 320 390 500 mV RL = 50 W, VTT = 1.8 V $5% VOH Output HIGH Voltage (Note 3) VTT − 170 VTT − 10 VTT mV VOL Output LOW Voltage (Note 3) VTT − 1100 VTT − 800 VTT − 640 mV |VOD| Differential Output Voltage Magnitude 570 780 1000 mV RL = 25 W, VTT = 1.8 V $5% VOH Output HIGH Voltage (Note 3) VTT − 85 VTT − 10 VTT mV VOL Output LOW Voltage (Note 3) VTT − 500 VTT − 400 VTT − 320 mV |VOD| Differential Output Voltage Magnitude 285 390 500 mV VEE VCC mV DIFFERENTIAL INPUT DRIVEN SINGLE−ENDED (Figures 14 and 16) Vth Input Threshold Reference Voltage Range (Note 5) VIH Single−ended Input HIGH Voltage Vth + 100 VCC + 400 mV VIL Single−ended Input LOW Voltage VEE − 400 Vth − 100 mV DIFFERENTIAL INPUTS DRIVEN DIFFERENTIALLY (Figures 15 and 17) VIHD Differential Input HIGH Voltage VEE VCC + 400 mV VILD Differential Input LOW Voltage VEE − 400 VCC − 100 mV VCMR Input Common Mode Range (Differential Configuration) VEE VCC mV |VID| Differential Input Voltage Magnitude (|VIHD − VILD|) (Note 7) 100 VCC − VEE mV CIN Input Capacitance (Note 7) 1.5 pF NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 3. CML outputs require RL receiver termination resistors to VTT for proper operation. Outputs must be connected through RL to VTT at power up. The output parameters vary 1:1 with VTT. 4. Input parameters vary 1:1 with VCC. 5. Vth is applied to the complementary input when operating in single−ended mode. 6. VCMR (MIN) varies 1:1 with VEE, VCMR max varies 1:1 with VCC. 7. Parameter guaranteed by design and evaluation but not tested in production. http://onsemi.com 4 NB4N11M Table 5. AC CHARACTERISTICS VCC = 3.0 V to 3.6 V, VEE = 0 V; (Note 8) −40°C Characteristic Symbol Min Typ 25°C Max Min Typ 85°C Max Min Typ Max Unit VOUTPP Output Voltage Amplitude (RL = 50 W) fin ≤ 1 GHz (See Figure 12) fin ≤ 1.5 GHz fin ≤ 2.5GHz 550 400 150 660 640 400 550 400 150 660 640 400 550 400 150 660 640 400 VOUTPP Output Voltage Amplitude (RL = 25 W) fin ≤ 1 GHz (See Figure 12) fin ≤ 1.5 GHz fin ≤ 2.5GHz 280 280 100 370 360 300 280 280 100 370 360 400 280 280 100 370 360 400 fDATA Maximum Operating Data Rate 1.5 2.5 1.5 2.5 1.5 2.5 tPLH, tPHL Propagation Delay to Output Differential @ 0.5 GHz 300 420 600 300 420 600 300 420 600 ps tSKEW Duty Cycle Skew (Note 9) Within Device Skew Device to Device Skew (Note 13) 2 5 20 20 25 100 2 5 20 20 25 100 2 5 20 20 25 100 ps tJITTER RMS Random Clock Jitter RL = 50 W and RL = 25 W (Note 11) fin = 750 MHz fin = 1.5 GHz fin = 2.5 GHz Peak−to−Peak Data Dependent Jitter RL = 50 W fDATA = 1.5 Gb/s (Note 12) fDATA = 2.5 Gb/s Peak−to−Peak Data Dependent Jitter RL = 25 W fDATA = 1.5 Gb/s (Note 12) fDATA = 2.5 Gb/s 1 1 1 3 3 3 1 1 1 3 3 3 1 1 1 3 3 3 15 20 55 85 15 20 55 85 15 20 55 85 5 10 35 35 5 10 35 35 5 10 35 35 VINPP Input Voltage Swing/Sensitivity (Differential Configuration) (Note 10) tr tf Output Rise/Fall Times @ 0.5 GHz (20% − 80%) 100 Q, Q 100 150 300 mV mV Gb/s 100 150 300 ps mV 150 300 ps OUTPUT VOLTAGE AMPLITUDE (mV) OUTPUT VOLTAGE AMPLITUDE (mV) NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 8. Measured by forcing VINPP (MIN) from a 50% duty cycle clock source. All output loaded with an external RL = 50 W and RL = 25 W to VTT. Outputs must be connected through RL to VTT at power up. Input edge rates 150 ps (20% − 80%). 9. Duty cycle skew is measured between differential outputs using the deviations of the sum of Tpw− and Tpw+ @ 0.5 GHz. 10. VINPP (MAX) cannot exceed VCC − VEE. Input voltage swing is a single−ended measurement operating in differential mode. 11. Additive RMS jitter with 50% duty cycle clock signal. 12. Additive peak−to−peak data dependent jitter with input NRZ data signal (PRBS 223−1). 13. Device to device skew is measured between outputs under identical transition @ 0.5 GHz. 800 0.8 700 RL = 50 W 600 500 400 RL = 25 W 300 200 100 0 0.75 1 1.25 1.5 1.75 2 2.25 2.5 2.75 3 0.7 RL = 50 W 0.6 0.5 0.4 RL = 25 W 0.3 0.2 0.1 0 0.75 1 1.25 1.5 1.75 2 2.25 2.5 2.75 3 INPUT CLOCK FREQUENCY (GHz) INPUT CLOCK FREQUENCY (GHz) (VCC − VEE = 3.3 V VTT = 3.3 V @ 255C Vin = 100 mV) (VCC − VEE = 3.0 V VTT = 1.71 V @255C Vin = 100 mV) Figure 3. Output Voltage Amplitude (VOUTPP) versus Input Clock Frequency (fIN) at Ambient Temperature (Typical) http://onsemi.com 5 NB4N11M NB4N11M 80 35 70 30 25 50 TIME (ps) TIME (ps) 60 40 −40°C 30 85°C 15 10 20 85°C 10 0 0.5 0.75 1 1.25 1.5 1.75 2 5 25°C −40°C 0 2.25 2.5 2.75 3 0.5 0.75 1 1.25 1.5 1.75 2 25°C 2.25 2.5 2.75 3 INPUT CLOCK FREQUENCY (GHz) INPUT CLOCK FREQUENCY (GHz) Figure 4. Data Dependent Jitter vs. Frequency and Temperature (VCC − VEE = 3.3 V; VTT = 3.3 V @ 255C; VIN = 100 mV; PRBS 223−1; RL = 50 W) Figure 5. Data Dependent Jitter vs. Frequency and Temperature (VCC − VEE = 3.3 V; VTT = 3.3 V @ 255C; VIN = 100 mV; PRBS 223−1; RL = 25 W) 600 550 550 500 500 450 TIME (ps) 600 tPD 400 350 300 −40 450 tPD 400 350 25 300 VEE − 0.5 V 85 V CC * V EE TEMPERATURE (°C) Figure 7. Typical Propagation Delay vs. Input Offset Voltage (VCC − VEE = 3.3 V; VTT = 3.3 V @ 255C; Vin = 100 mV RL = 50 W) 35 30 25 ICC 20 15 10 5 0 −40 VCC + 0.5 V 2 INPUT OFFSET VOLTAGE (V) Figure 6. Typical Propagation Delay vs. Temperature (VCC − VEE = 3.3 V; VTT = 3.3 V @ 255C; Vin = 100 mV; RL = 50 W) CURRENT (mA) TIME (ps) 20 25 TEMPERATURE (°C) Figure 8. Supply Current vs. Temperature http://onsemi.com 6 85 VOLTAGE (100 mV/div) VOLTAGE (200 mV/div) NB4N11M DDJ = 5 ps DDJ = 3 ps TIME (266.8 ps/div) TIME (266.8 ps/div) VOLTAGE (100 mV/div) VOLTAGE (200 mV/div) Figure 9. Typical Differential Output Waveform at 750 Mb/s (RL = 50 W Left Plot, RL = 25 W Right Plot, Vin = 100 mV, System DDJ = 24 ps) DDJ = 12 ps TIME (133.2 ps/div) DDJ = 5 ps TIME (133.2 ps/div) VOLTAGE (100 mV/div) VOLTAGE (200 mV/div) Figure 10. Typical Differential Output Waveform 1.5 Gb/s (RL = 50 W Left Plot, RL = 25 W Right Plot, Vin = 100 mV, System DDJ = 25 ps) DDJ = 20 ps TIME (80 ps/div) DDJ = 7 ps TIME (80 ps/div) Figure 11. Typical Differential Output Waveform 2.5 Gb/s (RL = 50 W Left Plot, RL = 25 W Right Plot, Vin = 100 mV, System DDJ = 24 ps) http://onsemi.com 7 NB4N11M D VINPP = VIH(D) − VIL(D) D Q VOUTPP = VOH(Q) − VOL(Q) Q tPHL tPLH Figure 12. AC Reference Measurement VTT 50 W 50 W Q DUT Driver Device D Z = 50 W Receiver Device Q D Z = 50 W Figure 13. Typical Termination for Output Driver and Device Evaluation D D D D Vth Vth Figure 14. Differential Input Driven Single−Ended VCC Vthmax Vthmin GND VCC VIHmax VILmax D Vth Figure 15. Differential Inputs Driven Differentially VIHCLKmax VCMmax D VIH Vth VIL VCMR D VIHmin VILmin VCMmax GND Figure 16. Vth Diagram VILCLKmax VID = VIHD − VILD VIHDtyp VILDtyp VIHDmin VILDmin Figure 17. VCMR Diagram http://onsemi.com 8 NB4N11M VCC Input ESD D 1.25 kW RC 1.25 kW RC 1.25 kW Input ESD 1.25 kW D Q Q IN IN Input ESD Input ESD Internal Current Source 16 mA Current Source VEE Input VEE Output Figure 18. CML Input and Output Structure http://onsemi.com 9 NB4N11M VTTA = VCCA VCCA = 1.8 V 2.5 V or 3.3 V VCC = 3.3 V Z = 50 W 50 W 50 W Receiver A Z = 50 W NB4N11M VTTB = VCCB 50 W VTTB = VCCB 50 W Z = 50 W 50 W 50 W VCCB = 1.8 V 2.5 V or 3.3 V Z = 50 W Receiver B VEE = 0 V VTTC = VCCC VCCC = 1.8 V 2.5 V or 3.3 V VCC = 3.3 V 75 W Z = 75 W NB4N11M 75 W Receiver C Z = 75 W VTTD = VCCD Z = 100 W 100 W 100 W VCCD = 1.8 V 2.5 V or 3.3 V Z = 100 W Receiver D VEE = 0 V Figure 19. Typical Examples of the Application Interface ORDERING INFORMATION Package Shipping † NB4N11MDTG TSSOP−8 (Pb−Free) 100 Units / Rail NB4N11MDTR2G TSSOP−8 (Pb−Free) 2500 / Tape & Reel Device †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 10 NB4N11M PACKAGE DIMENSIONS TSSOP−8 DT SUFFIX PLASTIC TSSOP PACKAGE CASE 948R−02 ISSUE A 8x 0.15 (0.006) T U 0.10 (0.004) S 2X L/2 L 8 5 1 PIN 1 IDENT 0.15 (0.006) T U K REF S M T U V S 0.25 (0.010) B −U− 4 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH. PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 6. DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE −W−. S M A −V− F DETAIL E C 0.10 (0.004) −T− SEATING PLANE D −W− G DETAIL E DIM A B C D F G K L M MILLIMETERS MIN MAX 2.90 3.10 2.90 3.10 0.80 1.10 0.05 0.15 0.40 0.70 0.65 BSC 0.25 0.40 4.90 BSC 0_ 6_ INCHES MIN MAX 0.114 0.122 0.114 0.122 0.031 0.043 0.002 0.006 0.016 0.028 0.026 BSC 0.010 0.016 0.193 BSC 0_ 6_ ECLinPS is a trademark of Semiconductor Components INdustries, LLC (SCILLC). ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: N. American Technical Support: 800−282−9855 Toll Free Literature Distribution Center for ON Semiconductor USA/Canada P.O. Box 61312, Phoenix, Arizona 85082−1312 USA Phone: 480−829−7710 or 800−344−3860 Toll Free USA/Canada Japan: ON Semiconductor, Japan Customer Focus Center 2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051 Fax: 480−829−7709 or 800−344−3867 Toll Free USA/Canada Phone: 81−3−5773−3850 Email: [email protected] http://onsemi.com 11 ON Semiconductor Website: http://onsemi.com Order Literature: http://www.onsemi.com/litorder For additional information, please contact your local Sales Representative. NB4N11M/D