RoboClock, CY7B995 2.5/3.3 V 200-MHz High-Speed Multi-Phase PLL Clock Buffer 2.5/3.3 V 200-MHz High-Speed Multi-Phase PLL Clock Buffer Features Description The CY7B995 RoboClock® is a low voltage, low power, eight-output, 200 MHz clock driver. It features output phase programmability which is necessary to optimize the timing of high performance computer and communication systems. ■ 2.5 V or 3.3 V operation ■ Split output bank power supplies ■ Output frequency range: 6 MHz to 200 MHz ■ 45 ps typical cycle-cycle jitter ■ ± 2% max output duty cycle ■ Selectable output drive strength ■ Selectable positive or negative edge synchronization ■ Eight LVTTL outputs driving 50 terminated lines ■ LVCMOS/LVTTL over-voltage tolerant reference input ■ Selectable phase-locked loop (PLL) frequency range and lock indicator ■ Phase adjustments in 625/1250 ps steps up to ± 7.5 ns ■ (1-6, 8, 10, 12) x multiply and (1/2,1/4) x divide ratios ■ Spread-Spectrum compatible ■ Power down mode ■ Selectable reference divider ■ Industrial temperature range: –40 °C to +85 °C ■ 44-pin TQFP package Cypress Semiconductor Corporation Document Number: 38-07337 Rev. *F • The user can program both the frequency and the phase of the output banks through nF[0:1] and DS[0:1] pins. The adjustable phase feature allows the user to skew the outputs to lead or lag the reference clock. Any one of the outputs can be connected to feedback to achieve different reference frequency multiplication, and divide ratios and zero input-output delay. The device also features split output bank power supplies, which enable the user to run two banks (1Qn and 2Qn) at a power supply level, different from that of the other two banks (3Qn and 4Qn). The three-level PE/HD pin also controls the synchronization of the output signals to either the rising, or the falling edge of the reference clock and selects the drive strength of the output buffers. The high drive option (PE/HD = MID) increases the output current from ± 12 mA to ± 24 mA. 198 Champion Court • San Jose, CA 95134-1709 • 408-943-2600 Revised February 4, 2011 [+] Feedback RoboClock, CY7B995 Logic Block Diagram TEST PE/HD PD#/DIV FS VDDQ1 3 3 /R REF 3 3 LOCK PLL FB /N 3 3 DS1:0 1F1:0 3 3 1Q0 Phase Select 1Q1 2Q0 3 2F1:0 3F1:0 3 3 3 Phase Select 2Q1 3Q0 Phase Select and /K 3Q1 VDDQ3 4F1:0 3 3 4Q0 Phase Select and /M 4Q1 VDDQ4 sOE# Document Number: 38-07337 Rev. *F Page 2 of 17 [+] Feedback RoboClock, CY7B995 Contents Pinouts .............................................................................. 4 Device Configuration ....................................................... 5 Governing Agencies ......................................................... 7 Absolute Maximum Conditions ....................................... 7 DC Specifications at 2.5 V ............................................... 8 DC Specifications at 3.3 V ............................................... 9 AC Input Specifications ................................................... 9 Switching Characteristics .............................................. 10 AC Timing Definitions .................................................... 11 AC Test Loads and Waveforms ..................................... 12 Ordering Information ...................................................... 13 Ordering Code Definitions ......................................... 13 Document Number: 38-07337 Rev. *F Package Drawing and Dimension ................................. 14 Acronyms ........................................................................ 15 Document Conventions ................................................. 15 Units of Measure ....................................................... 15 Document History Page ................................................. 16 Sales, Solutions, and Legal Information ...................... 17 Worldwide Sales and Design Support ....................... 17 Products .................................................................... 17 PSoC Solutions ......................................................... 17 Page 3 of 17 [+] Feedback RoboClock, CY7B995 Pinouts 4F1 sOE# PD#/DIV PE/HD VDDQ4 VDDQ4 4Q1 4Q0 VSS VSS VSS 1 2 3 4 5 6 7 8 9 10 11 1F1 2F0 VSS TES T 2F1 REF FS VDD 3F0 3F1 4F0 Figure 1. Pin Diagram - 44-pin TQFP Package Top view 44 43 42 41 40 39 38 37 36 35 34 CY7B995 1F0 32 DS1 31 DS0 30 LOCK 29 28 VDDQ1 VDDQ1 27 1Q0 26 24 1Q1 VSS VSS 23 VSS 25 VSS 2Q1 2Q0 VDDQ1 VDD FB VDDQ3 VDDQ3 3Q0 3Q1 VSS 12 13 14 15 16 17 18 19 20 21 22 Document Number: 38-07337 Rev. *F 33 Page 4 of 17 [+] Feedback RoboClock, CY7B995 Table 1. Pin Definitions - 44-pin TQFP Package Pin Name IO[1] Type Description 39 REF I LVTTL/LVCMOS Reference Clock Input. 17 FB I LVTTL Feedback Input. 37 TEST I 3-Level When MID or HIGH, disables PLL[2]. REF goes to all outputs. Set LOW for normal operation. 2 sOE# I, PD LVTTL Synchronous Output Enable. When HIGH, it stops clock outputs (except 2Q0 and 2Q1) in a LOW state (for PE/HD = H or M) – 2Q0, and 2Q1 may be used as the feedback signal to maintain phase lock. When TEST is held at MID level and sOE# is HIGH, the nF[1:0] pins act as output disable controls for individual banks when nF[1:0] = LL. Set sOE# LOW for normal operation. 4 PE/HD I, PU 3-Level Selects Positive or Negative Edge Control, and High or Low output Drive Strength. When LOW/HIGH, the outputs are synchronized with the negative/positive edge of the reference clock respectively. When at MID level, the output drive strength is increased and the outputs synchronize with the positive edge of the reference clock. See Table 10 on page 7. 34, 33, 36, 35, nF[1:0] 43, 42, 1, 44 I 3-Level Selects Frequency and Phase of the Outputs. See Table 4, Table 5, Table 6, Table 8, and Table 9 on page 6. 41 FS I 3-Level Selects VCO Operating Frequency Range. See Table 7 on page 6. 26,27,20,21, 13,14,7,8 nQ[1:0] O LVTTL Four banks of two outputs. See Table 6 on page 6 for frequency settings. 32, 31 DS[1:0] I 3-Level Selects Feedback Divider. See Table 3 on page 6. 3 PD#/DIV 30 LOCK 5,6 VDDQ4[3] PWR Power Power supply for Bank 4 Output Buffers. See Table 11 on page 7 for supply level constraints. 15,16 VDDQ3 [3] PWR Power Power supply for Bank 3 Output Buffers. See Table 11 on page 7 for supply level constraints. 19,28,29 VDDQ1[3] PWR Power Power supply for Bank 1 and Bank 2 Output Buffers. See Table 11 on page 7 for supply level constraints. 18,40 VDD[3] PWR Power Power supply for the Internal Circuitry. See Table 11 on page 7 for supply level constraints. PWR Power Ground 9-12, 22-25, 38 VSS I, PU 3-Level O LVTTL Power down and Reference Divider Control. When LOW, shuts off entire chip. When at MID level, enables the reference divider. See Table 2 for settings. PLL Lock Indication Signal. HIGH indicates lock, LOW indicates the PLL is not locked, and outputs may not be synchronized to the input. Device Configuration The outputs of the CY7B995 can be configured to run at frequencies ranging from 6 MHz to 200 MHz. The feedback input divider is controlled by the 3-level DS[0:1] pins as indicated in Table 3 on page 6, and the reference input divider is controlled by the 3-level PD#/DIV pin as indicated in Table 2. Table 2. Reference Divider Settings PD#/DIV R–Reference Divider H 1 M 2 L[4] N/A Notes 1. PD indicates an internal pull down and ‘PU’ indicates an internal pull up. 2. When TEST = MID and sOE# = HIGH, PLL remains active with nF[1:0] = LL functioning as an output disable control for individual output banks. Skew selections remain in effect unless nF[1:0] = LL. 3. A bypass capacitor (0.1F) must be placed as close as possible to each positive power pin (< 0.2”). If these bypass capacitors are not close to the pins, their high frequency filtering characteristic is cancelled by the lead inductance of the traces. 4. When PD#/DIV = LOW, the device enters power down mode. Document Number: 38-07337 Rev. *F Page 5 of 17 [+] Feedback RoboClock, CY7B995 Table 3. Feedback Divider Settings Input DS[1:0] N-Feedback Divider Permitted Output Divider Connected to FB The 3-level FS control pin setting determines the nominal operating frequency range of the divide-by-one outputs of the device. The CY7B995 PLL operating frequency range that corresponds to each FS level is given in Table 7. Table 7. Frequency Range Select LL 2 1 or 2 LM 3 1 FS PLL Frequency Range 24 to 50 MHz LH 4 1,2 or 4 L ML 5 1 or 2 M 48 to 100 MHz H 96 to 200 MHz MM 1 1,2 or 4 MH 6 1 or 2 HL 8 1 or 2 HM 10 1 HH 12 1 Selectable output skew is in discrete increments of time units (tU).The value of tU is determined by the FS setting and the maximum nominal frequency. The equation used to determine the tU value is: tU = 1 / (fNOM × MF) In addition to the reference and feedback dividers, the CY7B995 includes output dividers on Bank3 and Bank4, which are controlled by 3F[1:0] and 4F[1:0] as indicated in Table 4 and Table 5, respectively. Table 4. Output Divider Settings – Bank 3 3F[1:0] K - Bank3 Output Divider LL 2 HH 4 Other[5] 1 where MF is a multiplication factor which is determined by the FS setting as indicated in Table 8. Table 8. MF Calculation FS MF fNOM at which tU is 1.0 ns (MHz) L 32 31.25 M 16 62.5 H 8 125 Table 9. Output Skew Settings Table 5. Output Divider Settings – Bank 4 nF[1:0] Skew (1Q[0:1],2Q[0:1]) Skew (3Q[0:1]) Skew (4Q[0:1]) LL[7] –4tU Divide By 2 Divide By 2 4F[1:0] M- Bank4 Output Divider LM –3tU –6tU –6tU LL 2 LH Other[5] –2tU –4tU –4tU 1 The divider settings and the FB input to any output connection needed to produce various output frequencies are summarized in Table 6. Table 6. Output Frequency Settings Configuration FB Input Connected to Output Frequency 1Q[0:1] and 2Q[0:1][6] 3Q[0:1] ML –1tU –2tU –2tU MM Zero Skew Zero Skew Zero Skew MH +1tU +2tU +2tU HL +2tU +4tU +4tU HM +3tU +6tU +6tU HH +4tU Divide By 4 Inverted[8] 4Q[0:1] 1Qn or 2Qn (N / R) x FREF (N / R) x (1 / (N / R) x (1 / K) x FREF M) x FREF 3Qn (N / R) x K x (N / R) x FREF (N / R) x (K / FREF M) x FREF 4Qn (N / R) x M x (N / R) x (M / (N / R) x FREF FREF K) x FREF Notes 5. These states are used to program the phase of the respective banks. See Table 8 and Table 9. 6. These outputs are undivided copies of the VCO clock. The formulas in this column can be used to calculate the VCO operating frequency (FNOM) at a given reference frequency (FREF), and divider and feedback configuration. The user must select a configuration and a reference frequency that generates a VCO frequency, and is within the range specified by FS pin. See Table 7. 7. LL disables outputs if TEST = MID and sOE# = HIGH. 8. When 4Q[0:1] are set to run inverted (HH mode), sOE# disables these outputs HIGH when PE/HD = HIGH or MID, sOE# disables them LOW when PE/HD = LOW. Document Number: 38-07337 Rev. *F Page 6 of 17 [+] Feedback RoboClock, CY7B995 Governing Agencies In addition to determining whether the outputs synchronize to the rising or the falling edge of the reference signal, the 3-level PE/HD pin controls the output buffer drive strength as indicated in Table 10. Refer to the AC Timing Definitions section for a description of input-to-output and output-to-output phase relationships. Table 10. PE/HD Settings PE/HD Synchronization The following agencies provide specifications that apply to the CY7B995. The agency name and relevant specification is listed below. Table 12. Governing Agencies and Specifications Agency Name Output Drive Strength[9] L Negative Low Drive M Positive High Drive H Positive Low Drive Specification JEDEC JESD 51 (Theta JA) JESD 65 (Skew, Jitter) The CY7B995 features split power supply buses for Banks 1 and 2, Bank 3 and Bank 4, which enables the user to obtain both 3.3 V and 2.5 V output signals from one device. The core power supply (VDD) must be set at a level that is equal to or higher than any of the output power supplies. IEEE 1596.3 (Jiter Specs) UL-194_V0 94 (Moisture Grading) MIL 883E Method 1012.1 (Therma Theta JC) Table 11. Power Supply Constraints VDD 3.3 V 2.5 V VDDQ1[10] VDDQ3[10] VDDQ4[10] 3.3 V or 2.5 V 3.3 V or 2.5 V 3.3 V or 2.5 V 2.5 V 2.5 V 2.5 V Absolute Maximum Conditions Parameter Description Condition Min Max Unit VDD Operating Voltage Functional @ 2.5 V ± 5% 2.25 2.75 V VDD Operating Voltage Functional @ 3.3 V ± 10% 2.97 3.63 V VIN(MIN) Input Voltage Relative to VSS VSS – 0.3 – V VIN(MAX) Input Voltage Relative to VDD – VDD + 0.3 V VREF(MAX) Reference Input Voltage VDD = 3.3 V – 5.5 V VREF(MAX) Reference Input Voltage VDD = 2.5 V – 4.6 V TS Temperature, Storage Non Functional –65 +150 °C TA Temperature, Operating Ambient Functional –40 +85 °C TJ Temperature, Junction Functional – 155 °C ØJC Dissipation, Junction to Case Mil-Spec 883E Method 1012.1 – 42 °C/W ØJA Dissipation, Junction to Ambient JEDEC (JESD 51) – 74 °C/W ESDHBM ESD Protection (Human Body Model) MIL-STD-883, Method 3015 2000 – V UL-94 Flammability Rating @1/8 in. MSL Moisture Sensitivity Level FIT Failure in Time V–0 1 Manufacturing Testing 10 ppm Notes 9. Please refer to “DC Parameters” section for IOH/IOL specifications. 10. VDDQ1/3/4 must not be set at a level higher than that of VDD. They can be set at different levels from each other, e.g., VDD = 3.3 V, VDDQ1 = 3.3 V, VDDQ3 = 2.5 V and VDDQ4 = 2.5 V. Document Number: 38-07337 Rev. *F Page 7 of 17 [+] Feedback RoboClock, CY7B995 DC Specifications at 2.5 V Parameter Description Condition VDD 2.5 V Operating Voltage 2.5 V ± 5% VIL Input LOW Voltage REF, FB, and sOE# Inputs VIH Input HIGH Voltage VIHH [11] Input HIGH Voltage 3-Level Inputs, (TEST, FS, nF[1:0], DS[1:0], PD#/DIV, PE/HD). (These pins are normally wired to VDD, GND, or unconnected) VIMM[11] Input MID Voltage VILL[11] Input LOW Voltage IIL Input Leakage Current I3 3-Level Input DC Current HIGH, VIN = VDD MID, VIN = VDD/2 Min Max Unit 2.375 2.625 V – 0.7 V 1.7 – V VDD – –0.4 – VDD/2 – 0.2 VDD/2 + 0.2 – VIN = VDD/GND,VDD = Max; (REF and FB Inputs) LOW, VIN = VSS 3-Level Inputs (TEST, FS, nF[1:0], DS[1:0], PD#/DIV, PE/HD) V V 0.4 V –5 5 A – 200 A –50 50 A –200 – A –25 – A IPU Input Pull-Up Current VIN = VSS, VDD = Max IPD Input Pull-Down Current VIN = VDD, VDD = Max, (sOE#) – 100 A VOL Output LOW Voltage IOL = 12 mA (PE/HD = L/H), (nQ[0:1]) – 0.4 V IOL = 20 mA (PE/HD = MID),(nQ[0:1]) – 0.4 V IOL = 2 mA (LOCK) – 0.4 V VOH Output HIGH Voltage IOH = –12 mA (PE/HD = L/H),(nQ[0:1]) 2.0 – V IOH = –20 mA (PE/HD = MID),(nQ[0:1]) 2.0 – V IOH = –2 mA (LOCK) 2.0 – V – 2 mA 10(typ.) 25 A IDDQ Quiescent Supply Current VDD = Max, TEST = MID, REF = LOW, sOE# = LOW, Outputs Not Loaded IDDPD Power down Current PD#/DIV, sOE# = LOW Test,nF[1:0],DS[1:0] = HIGH; VDD = Max IDD Dynamic Supply Current At 100 MHz CIN Input Pin Capacitance 150 mA 4 pF Note 11. These Inputs are normally wired to VDD, GND or unconnected. Internal termination resistors bias unconnected inputs to VDD/2. Document Number: 38-07337 Rev. *F Page 8 of 17 [+] Feedback RoboClock, CY7B995 DC Specifications at 3.3 V Parameter Description Condition VDD 3.3 V Operating Voltage 3.3 V ± 10% VIL Input LOW Voltage REF, FB and sOE# Inputs VIH Input HIGH Voltage VIHH[12] Input HIGH Voltage VIMM[12] Input MID Voltage VILL[12] Input LOW Voltage IIL Input Leakage Current VIN = VDD/GND,VDD = Max (REF and FB inputs) I3 3-Level Input DC Current HIGH, VIN = VDD Min Max Unit 2.97 3.63 V – 0.8 V 2.0 – V 3-Level Inputs VDD – –0.6 – (TEST, FS, nF[1:0], DS[1:0],PD#/DIV, PE/HD); (These pins V /2 – 0.3 V /2 + DD DD are normally wired to VDD,GND or unconected 0.3 3-Level Inputs, (TEST, FS, nF[1:0], DS[1:0], PD#/DIV, PE/HD) MID, VIN = VDD/2 LOW, VIN = VSS V V – 0.6 V –5 5 A – 200 A –50 50 A –200 – A –25 – A IPU Input Pull Up Current VIN = VSS, VDD = Max IPD Input Pull Down Current VIN = VDD, VDD = Max, (sOE#) – 100 A VOL Output LOW Voltage IOL = 12 mA (PE/HD = L/H), (nQ[0:1]) – 0.4 V VOH Output HIGH Voltage IOL = 24 mA (PE/HD = MID),(nQ[0:1]) – 0.4 V IOL = 2 mA (LOCK) – 0.4 V IOH = –12 mA (PE/HD = L/H),(nQ[0:1]) 2.4 – V IOH = –24 mA (PE/HD = MID),(nQ[0:1]) 2.4 – V IOH = –2 mA (LOCK) 2.4 – V – 2 mA 10(typ.) 25 A IDDQ Quiescent Supply Current VDD = Max, TEST = MID, REF = LOW, sOE# = LOW, Outputs Not Loaded IDDPD Power Down Current PD#/DIV, sOE# = LOW, Test,nF[1:0],DS[1:0] = HIGH, VDD = Max IDD Dynamic Supply Current At 100 MHz CIN Input Pin Capacitance 230 mA 4 pF AC Input Specifications Parameter Description Condition TR,TF Input Rise/Fall Time 0.8 V – 2.0 V TPWC Input Clock Pulse HIGH or LOW TDCIN Input Duty Cycle FREF Reference Input Frequency[13] Min Max Unit – 10 ns/V 2 – ns 10 90 % MHz FS = LOW 2 50 FS = MID 4 100 FS = HIGH 8 200 Notes 12. These Inputs are normally wired to VDD, GND or unconnected. Internal termination resistors bias unconnected inputs to VDD/2. 13. IF PD#/DIV is in HIGH level (R-reference divider = 1). Reference Input Frequency = FREF. IF PD#/DIV is in MID level (R-reference divider = 2). Reference Input Frequency = FREFx2. Document Number: 38-07337 Rev. *F Page 9 of 17 [+] Feedback RoboClock, CY7B995 Switching Characteristics Parameter Description Condition Min FOR Output frequency range VCOLR VCO Lock Range VCOLBW VCO Loop Bandwidth 0.25 tSKEWPR Matched-Pair Skew[14] Skew between the earliest and the latest output transitions within the same bank. – tSKEW0 Output-Output Skew[14] Skew between the earliest and the latest output transitions among all outputs at 0tU. – tSKEW1 Skew between the earliest and the latest output transitions among all outputs for which the same phase delay has been selected. tSKEW2 tSKEW3 tSKEW4 Output-Output Skew[14] tSKEW5 Type Max Unit 6 – 200 MHz 200 – 400 MHz – 3.5 MHz – 100 ps – 200 ps – – 200 ps Skew between the nominal output rising edge to the inverted output falling edge. – – 500 ps Skew between non-inverted outputs running at different frequencies. – – 500 ps Skew between nominal to inverted outputs running at different frequencies. – – 500 ps Skew between nominal outputs at different power supply levels. – – 650 ps Skew between the outputs of any two devices under identical settings and conditions (VDDQ, VDD, temp, air flow, frequency, etc.). – – 750 ps –250 – +250 ps 52 % tPART Part-Part Skew tPD0 Ref to FB Propagation Delay[15] tODCV Output Duty Cycle Fout < 100 MHz, Measured at VDD/2. 48 – Fout > 100 MHz, Measured at VDD/2. 45 – 55 tPWH Output High Time Deviation from 50% Measured at 2.0 V for VDD = 3.3 V and at 1.7 V for VDD = 2.5 V. – – 1.5 ns tPWL Output Low Time Deviation from 50% Measured at 0.8 V for VDD = 3.3 V and at 0.7 V for VDD = 2.5 V. – – 2.0 ns tR/tF Output Rise/Fall Time Measured at 0.8 V–2.0 V for VDD = 3.3 V and 0.7 V–1.7 V for VDD = 2.5 V. 0.15 – 1.5 ns tLOCK PLL Lock Time[16, 17] – – 0.5 ms tCCJ Cycle-Cycle Jitter Divide by one output frequency, FS = L, FB = divide by any. – 45 100 ps Divide by one output frequency, FS = M/H, FB = divide by any. – 55 150 ps Notes 14. Test Load = 20 pF, terminated to VCC/2. All outputs are equally loaded. 15. tPD is measured at 1.5 V for VDD = 3.3 V and at 1.25 V for VDD = 2.5 V with REF rise/fall times of 0.5 ns between 0.8 V–2.0 V. 16. tLOCK is the time that is required before outputs synchronize to REF. This specification is valid with stable power supplies which are within normal operating limits. 17. Lock detector circuit may be unreliable for input frequencies lower than 4 MHz, or for input signals which contain significant jitter. Document Number: 38-07337 Rev. *F Page 10 of 17 [+] Feedback RoboClock, CY7B995 AC Timing Definitions Figure 2. Timing Definition tREF tPWL tPWH REF tPD t0DCV t0DCV FB tCCJ1-12 Q tSKEWPR tSKEW0,1 tSKEWPR tSKEW0,1 OTHER Q tSKEW1 tSKEW1 INVERTED Q tSKEW3 tSKEW3 tSKEW3 DIVIDE BY 2 OUTPUT tSKEW1,3,4 tSKEW1,3,4 DIVIDE BY 4 OUTPUT With PE HIGH (LOW), the REF rising (falling) edges are aligned to the FB rising (falling) edges. Also, when PE is HIGH (LOW), all divided outputs’ rising (falling) edges are aligned to the rising (falling) edges of the undivided, non-inverted outputs. Regardless of PE setting, divide-by-4 outputs’ rising edges align to the divide-by-2 outputs’ rising edges. Document Number: 38-07337 Rev. *F In cases where a non-divided output is connected to the FB input pin, the divided output rising edges can be either 0 or 180 degrees phase aligned to the REF input rising edges (as set randomly at power-up). If the divided outputs are required as rising-edge (falling-edge) aligned to the REF input’s rising (falling) edge, set the PE pin HIGH (LOW) and connect the lowest frequency divided output to the FB input pin. This setup provides a consistent input-output and output-output phase relationship. Page 11 of 17 [+] Feedback RoboClock, CY7B995 AC Test Loads and Waveforms Figure 3. For Lock Output and all other Outputs VDDQ O u tp u t 20pF O u tp u t 20pF F o r L o ck O u tp u t F o r A ll O th e r O u tp u ts Figure 4. 3.3V LVTTL and 2.5V LVTTL Output Waveforms tORISE tPWH 2.0V tORISE tOFALL tOFALL tPWH 1.7V VTH =1.25V VTH =1.5V 0.8V tPWL tPWL 0.7V 2.5V LVTTL OUTPUT WAVEFORM 3.3V LVTTL OUTPUT WAVEFORM Figure 5. 3.3 V LVTTL and 2.5 V LVTTL Input Test Waveforms 1ns 3.0V 2.0V VTH =1.5V 0.8V 0V 3.3V LVTTL INPUT TEST WAVEFORM Document Number: 38-07337 Rev. *F 1ns 1ns 1ns 2.5V 1.7V VTH =1.25V 0.7V 0V 2.5V LVTTL INPUT TEST WAVEFORM Page 12 of 17 [+] Feedback RoboClock, CY7B995 Ordering Information Part Number Package Type Product Flow Status Pb-free CY7B995AXC 44-pin TQFP Commercial, 0 C to 70 C CY7B995AXCT 44-pin TQFP – Tape and Reel Commercial, 0 C to 70 C Active CY7B995AXI 44-pin TQFP Industrial, –40 C to 85 C Active CY7B995AXIT 44-pin TQFP – Tape and Reel Industrial, –40 C to 85 C Active Active Ordering Code Definitions CY 7B995 AX X T T = Tape and Reel Temperature Range: X = C or I C = Commercial; I = Industrial Package Type: AX = 44-pin TQFP Base Device Part Number Company ID: CY = Cypress Document Number: 38-07337 Rev. *F Page 13 of 17 [+] Feedback RoboClock, CY7B995 Package Drawing and Dimension Figure 6. 44-pin Thin Plastic Quad Flat Pack (10 × 10 × 1.0 mm) A44SB 51-85155 *B Document Number: 38-07337 Rev. *F Page 14 of 17 [+] Feedback RoboClock, CY7B995 Acronyms Acronym Description CMOS complementary metal oxide semiconductor ESD electrostatic discharge LVCMOS Low Voltage Complementary Metal Oxide Semiconductor LVTTL Low Voltage Transistor-Transistor Logic PLL phase locked loop TQFP thin quad flat pack VCO voltage-controlled oscillator Document Conventions Units of Measure Symbol °C Unit of Measure degree Celsius Hz Hertz kHz kilo Hertz MHz Mega Hertz µA micro Amperes mA milli Amperes ms milli seconds ns nano seconds ohms % percent pF pico Farads ps pico seconds ppm parts per million mV milli Volts V Volts W Watts Document Number: 38-07337 Rev. *F Page 15 of 17 [+] Feedback RoboClock, CY7B995 Document History Page Document Title: RoboClock, CY7B995 2.5/3.3 V 200-MHz High-speed Multi-phase PLL Clock Buffer Document Number: 38-07337 REV. ECN No. Issue Date Orig. of Change Description of Change ** 122626 01/10/03 RGL New Data Sheet *A 205743 See ECN RGL Changed Pin 5 from VDD to VDDQ4, Pin 16 from VDD to VDDQ3 and Pin 29 from VDD to VDDQ1 Added pin 1 indicator in the Pin Configuration Drawing *B 362760 See ECN RGL Added description on the AC Timing Waveforms Added typical value for cycle-to-cycle jitter *C 389237 See ECN RGL Added Lead-free devices *D 1562063 See ECN *E 2892312 03/15/2010 CXQ Added Table of Contents Removed part numbers CY7B995AC, CY7B995ACT, CY7B995AI and CY7B995AIT in ordering information table. Updated package diagram (Figure 6) Added Sales, Solutions, and Legal Information *F 3162976 02/04/2011 CXQ Added Ordering Code Definitions. Added Acronyms and Units of Measure. Minor edits and updated in new template. Document Number: 38-07337 Rev. *F PYG/AESA Added Status column to Ordering Information table Page 16 of 17 [+] Feedback RoboClock, CY7B995 Sales, Solutions, and Legal Information Worldwide Sales and Design Support Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office closest to you, visit us at Cypress Locations. Products Automotive Clocks & Buffers Interface Lighting & Power Control PSoC Solutions cypress.com/go/automotive cypress.com/go/clocks psoc.cypress.com/solutions cypress.com/go/interface PSoC 1 | PSoC 3 | PSoC 5 cypress.com/go/powerpsoc cypress.com/go/plc Memory Optical & Image Sensing cypress.com/go/memory cypress.com/go/image PSoC cypress.com/go/psoc Touch Sensing cypress.com/go/touch USB Controllers Wireless/RF cypress.com/go/USB cypress.com/go/wireless © Cypress Semiconductor Corporation, 2003-2011. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign), United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of, and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without the express written permission of Cypress. Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Use may be limited by and subject to the applicable Cypress software license agreement. Document Number: 38-07337 Rev. *F Revised February 4, 2011 Page 17 of 17 RoboClock is a registered trademark of Cypress Semiconductor. All products and company names mentioned in this document may be the trademarks of their respective holders. [+] Feedback