CLD-DS33 Rev 2 Product family data sheet Cree® XLamp® XM-L LEDs Product Description FEATURES The XLamp XM-L LED is the indus- • try’s highest performance, singledie white lighting-class LED. XLamp XM-L is 20% more efficient than XLamp XP-G at the same current, and can deliver 1000 lumens with 3000 mA • Low thermal resistance: 2.5°C/W • 100 lumens per Watt efficacy. The Maximum junction Electrical Characteristics.............. 4 Thermal Design.......................... 4 • Viewing angle: 125° dustry-leading features: wide view- • Available in warm, neutral and unlimited floor life and electrically neutral thermal path. XLamp XM-L LEDs can enable LED cool white • • light into new applications that require tens of thousands of lumens, • such as high bay and high-output area lighting. XM-L is also the ideal choice for lighting applications where high light output and maximum efficacy are required, such as LED light bulbs, outdoor lighting, portable lighting, indoor lighting and solar-powered lighting. Relative Flux vs. Current............. 5 Relative Chromaticity vs. Current and Temperature (Cool White)...... 5 ANSI-compatible chromaticity Relative Chromaticity vs. Current bins and Temperature (Warm White).... 6 Unlimited floor life at Typical Spatial Distribution........... 7 ≤ 30ºC/85% RH Reflow Soldering Characteristics... 8 Reflow solderable JEDEC J-STD-020C • Flux Characteristics. 2 Label with Cree .................... Bin Code, Qty, Lot #.......................................2 Characteristics........................... 10 Relative Power Label with Spectral Customer Order Code,... 10 Distribution............................... 3 Qty, Reel ID, PO#........................... Relative Flux vs. Junction 10 Temperature.............................. 3 temperature: 150°C XLamp XM-L LED offers Cree’s ining angle, symmetrical package, WWW.CREE.COM/XLAMP Maximum drive current: TABLE OF CONTENTS Electrically neutral thermal path Notes........................................ 9 Mechanical Dimensions..............10 Tape and Reel............................ 9 Packaging.................................10 Label with Cree Bin Code, Qty, Lot #.................................. 10 Label with Customer Order Code,......................................... 10 Qty, Reel ID, PO#...................... 10 Copyright © 2010-2011 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Copyright © 2010 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc. Cree, the Cree logo and XLamp are registered trademarks of Cree, Inc. Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 www.cree.com/xlamp xlamp xm-l leds Flux Characteristics (TJ = 25°C) The following table provides several base order codes for XLamp XM-L LEDs. It is important to note that the base order codes listed here are a subset of the total available order codes for the product family. For more order codes, as well as a complete description of the order-code nomenclature, please consult the XLamp XM-L Binning and Labeling document. CCT Range Color Min. Max. Cool White 5,000 K 8,300 K Neutral White 3,700 K 5,000 K Warm White 2,600 K 3,700 K Base Order Codes Min Luminous Flux @ 700 mA (lm) Order Code Group Flux (lm) T5 260 XMLAWT-00-0000-0000T5051 T6 280 XMLAWT-00-0000-0000T6051 T4 240 XMLAWT-00-0000-000LT40E4 T5 260 XMLAWT-00-0000-000LT50F4 T2 200 XMLAWT-00-0000-000LT20E7 T3 220 XMLAWT-00-0000-000LT30F7 Notes: • Cree maintains a tolerance of ± 7% on flux and power measurements and ± 2 on CRI measurements . • Typical CRI for Cool White (5,000 K – 8,300 K CCT) is 65. • Typical CRI for Neutral White (3,700 K – 5,000 K CCT) is 75. • Typical CRI for Warm White (2,600 K – 3,700 K CCT) is 80. Characteristics Characteristics Unit Thermal Resistance, junction to solder point °C/W 2.5 degrees 125 Viewing Angle (FWHM) Temperature coefficient of voltage mV/°C ESD Classification (HBM per Mil-Std-883D) DC Forward Current Minimum Typical Maximum -3.0 Class 2 mA 3000 Reverse Voltage V 5 Forward voltage (@ 700 mA) V 2.9 Forward voltage (@ 1500 mA) V 3.1 Forward voltage (@ 3000 mA) V 3.35 LED Junction Temperature °C 3.5 150 Copyright © 2010-2011 Inc. All rights reserved. The information this document is subject to change without notice. the logo Cree and logoXLamp and XLamp are registered trade2010 Cree, Cree, Inc. All rights reserved. The information in thisindocument is subject to change without notice. Cree, Cree, the Cree are registered trademarks marks ofInc. Cree, Inc. of Cree, 2 xlamp xm-l leds Relative Spectral Power Distribution Relative Radiant Power (%) 100 Relative Spectral Power 80 60 2600K -3700K CCT 3700K - 5000K CCT 40 5000K - 8300K CCT 20 0 400 450 500 550 600 650 700 750 -20 Wavelength (nm) Relative Flux vs. Junction Temperature (IF = 700 mA) 100% Relative Luminous Flux 90% 80% 70% 60% 50% 40% 30% 20% 10% 0% 25 50 75 100 125 150 Junction Temperature (ºC) Copyright © 2010-2011 Inc. All rights reserved. The information this document is subject to change without notice. the logo Cree and logoXLamp and XLamp are registered trade2010 Cree, Cree, Inc. All rights reserved. The information in thisindocument is subject to change without notice. Cree, Cree, the Cree are registered trademarks marks ofInc. Cree, Inc. of Cree, 3 xlamp xm-l leds Electrical Characteristics Electrical Characteristics (Tj = 25ºC) (TJ = 25°C) 3000 2800 2600 Forward Current (mA) 2400 2200 2000 1800 1600 1400 1200 1000 800 600 400 200 0 2.00 2.20 2.40 2.60 2.80 3.00 3.20 3.40 3.60 Forward Voltage (V) Thermal Design The maximum forward current is determined by the thermal resistance between the LED junction and ambient. It is crucial for the end product to be designed in a manner that minimizes the thermal resistance from the solder point to Cool White ambient in order to optimize lamp life and optical characteristics. 3500 Maximum Current (mA) 3000 2500 2000 1500 Thermal Design 1000 Rj-a = 4°C/W Rj-a = 7°C/W Rj-a = 10°C/W 500 Rj-a = 15°C/W 0 0 20 40 60 80 100 120 140 Ambient Temperature (ºC) Copyright © 2010-2011 Inc. All rights reserved. The information this document is subject to change without notice. the logo Cree and logoXLamp and XLamp are registered trade2010 Cree, Cree, Inc. All rights reserved. The information in thisindocument is subject to change without notice. Cree, Cree, the Cree are registered trademarks marks ofInc. Cree, Inc. of Cree, 4 xlamp xm-l leds Relative Flux vs. Current (TJ = 25°C) 350% Relative Luminous Flux (%) 325% 300% 275% 250% 225% 200% 175% 150% 125% 100% 75% Typical Spatial Radiation Pattern 50% 25% 0% 0 200 400 600 800 1000 1200 1400 1600 1800 2000 2200 2400 2600 2800 3000 Forward Current (mA) Relative Chromaticity versus Current and Temperature (Cool White) Cool White 0.020 0.015 0.010 0.005 0.000 ΔCCx -0.005 ΔCCy -0.010 -0.015 -0.020 0 500 1000 1500 2000 2500 3000 Current (mA) Warm White 0.020 0.015 Copyright © 2010-2011 Inc. All rights reserved. The information this document is subject to change without notice. the logo Cree and logoXLamp and XLamp are registered trade2010 Cree, Cree, Inc. All rights reserved. The information in thisindocument is subject to change without notice. Cree, Cree, the Cree are registered trademarks marks ofInc. Cree, Inc. of Cree, 0.010 0.005 5 xlamp xm-l leds Relative Chromaticity versus Current and Temperature (Cool White) Cool White 0.020 0.015 Cool0.010 White 0.005 0.020 0.000 0.015 -0.005 0.010 -0.010 0.005 -0.015 0.000 -0.020 ΔCCx ΔCCy -0.005 25 50 75 -0.010 100 125 150 Tsp (°C) ΔCCx ΔCCy -0.015 -0.020 White RelativeWarm Chromaticity versus Current Temperature (Warm White) 0 500 1000 1500 and2000 2500 3000 Current (mA) 0.020 0.015 0.010 Warm White 0.005 0.020 0.000 0.015 -0.005 0.010 -0.010 0.005 -0.015 0.000 -0.020 -0.005 25 ΔCCx ΔCCy 50 75 -0.010 100 125 150 Tsp (°C) ΔCCx ΔCCy -0.015 -0.020 0 500 1000 1500 2000 2500 3000 Current (mA) Copyright © 2010-2011 Inc. All rights reserved. The information this document is subject to change without notice. the logo Cree and logoXLamp and XLamp are registered trade2010 Cree, Cree, Inc. All rights reserved. The information in thisindocument is subject to change without notice. Cree, Cree, the Cree are registered trademarks marks ofInc. Cree, Inc. of Cree, 6 0.000 ΔCCx -0.005 ΔCCy -0.010 -0.015 xlamp xm-l leds -0.020 25 50 75 100 125 150 Relative Chromaticity versus Current and Temperature (Warm White) Tsp (°C) Warm White 0.020 0.015 0.010 0.005 0.000 ΔCCx -0.005 ΔCCy -0.010 -0.015 -0.020 25 50 75 100 125 150 Tsp (°C) Typical Spatial Distribution Relative Luminous Intensity (%) 120 100 80 60 40 20 0 -100 -80 -60 -40 -20 0 20 40 60 80 100 Angle (º) Copyright © 2010-2011 Inc. All rights reserved. The information this document is subject to change without notice. the logo Cree and logoXLamp and XLamp are registered trade2010 Cree, Cree, Inc. All rights reserved. The information in thisindocument is subject to change without notice. Cree, Cree, the Cree are registered trademarks marks ofInc. Cree, Inc. of Cree, 7 xlamp xm-l leds Reflow Soldering Characteristics In testing, Cree has found XLamp XM-L LEDs to be compatible with JEDEC J-STD-020C, using the parameters listed below. As a general guideline, Cree recommends that users follow the recommended soldering profile provided by the manufacturer of solder paste used. Note that this general guideline may not apply to all PCB designs and configurations of reflow soldering equipment. Profile Feature Lead-Based Solder Lead-Free Solder 3°C/second max. 3°C/second max. Preheat: Temperature Min (Tsmin) 100°C 150°C Preheat: Temperature Max (Tsmax) 150°C 200°C 60-120 seconds 60-180 seconds 183°C 217°C 60-150 seconds 60-150 seconds 215°C 260°C 10-30 seconds 20-40 seconds 6°C/second max. 6°C/second max 6 minutes max. 8 minutes max. Average Ramp-Up Rate (Tsmax to Tp) Preheat: Time (tsmin to tsmax) Time Maintained Above: Temperature (TL) Time Maintained Above: Time (tL) Peak/Classification Temperature (Tp) Time Within 5°C of Actual Peak Temperature (tp) Ramp-Down Rate Time 25°C to Peak Temperature Note: All temperatures refer to the topside of the package, measured on the package body surface. Copyright © 2010-2011 Inc. All rights reserved. The information this document is subject to change without notice. the logo Cree and logoXLamp and XLamp are registered trade2010 Cree, Cree, Inc. All rights reserved. The information in thisindocument is subject to change without notice. Cree, Cree, the Cree are registered trademarks marks ofInc. Cree, Inc. of Cree, 8 xlamp xm-l leds Notes Lumen Maintenance Projections Cree currently recommends a maximum drive current of 2000 mA for XLamp XM-L white in designs seeking the ENERGY STAR* 35,000 hour lifetime rating (≥ 94.1% luminous flux @ 6000 hours) or 25,000-hour lifetime rating (≥ 91.8% luminous flux @ 6000 hours). Please read the XLamp Long-Term Lumen Maintenance application note for more details on Cree’s lumen maintenance testing and forecasting. Please read the XLamp Thermal Management application note for details on how thermal design, ambient temperature, and drive current affect the LED junction temperature. * These lifetime ratings are based on the current ENERGY STAR Solid State Lighting Luminaires V1.1 (December 12, 2008) and ENERGY STAR Integral LED Lamps V1.0 (December 3, 2009) lumen maintenance criteria. Moisture Sensitivity In testing, Cree has found XLamp XM-L LEDs to have unlimited floor life in conditions ≤30ºC / 85% relative humidity (RH). Moisture testing included a 168 hour soak at 85ºC / 85% RH followed by 3 reflow cycles, with visual and electrical inspections at each stage. Vision Advisory Claim WARNING: Do not look at exposed lamp in operation. Eye injury can result. See LED Eye Safety at http://www.cree. com/products/pdf/XLamp_EyeSafety.pdf. Copyright © 2010-2011 Inc. All rights reserved. The information this document is subject to change without notice. the logo Cree and logoXLamp and XLamp are registered trade2010 Cree, Cree, Inc. All rights reserved. The information in thisindocument is subject to change without notice. Cree, Cree, the Cree are registered trademarks marks ofInc. Cree, Inc. of Cree, 9 4.8 C xlamp xm-l leds Mechanical Dimensions All measurements are ±.13 mm unless otherwise indicated. 4.7 3.9 0.6 B 6 5 4 NOTICE 6 CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION 4.7 NOTICE CONTAINED WITHIN ARE THE PROPRIETARY AND CREE CONFIDENTIAL. CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT THIS PLOT AND THE INFORMATION CONTAINED WITHINTO ARE THE PROPRIETARY AND MAY NOT BE COPIED, REPRODUCED OR DISCLOSED ANY CONFIDENTIAL OF CREE, INC. THIS PLOT UNAUTHORIZED PERSON WITHOUT THE WRITTENINFORMATION CONSENT MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY OF CREE INC. UNAUTHORIZED PERSON WITHOUTTHE WRITTEN CONSENT OF CREE INC. 0.4 3 5 2 4 1 REVISONS 3 REV 2 BY DESCRIPTION A 4/15/10 DC DESCRIPTION REV NEW RELEASE B Added die outline A 10/22/1 DDSRELEAS NEW C ADDED DIMENSION FOR TOP OF FLASH B D 3.02 WAS 3.09 C 11/18/1 DC die Added outli 1/5/11T DC ADDED DIMENSION FOR D 0.4 DATE 3.02 WAS 3.0 D D 3.8 0.4 RECOMMENDED STENCIL PATTERN SHADED AREA IS OPEN 5.00 THIRD ANGLE PROJECTION UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETERS AND AFTER FINISH. TOLERANCE UNLESS SPECIFIED: 5.00 .XX ± .25 .XXX ± .125 X° ± .5 ° FOR SHEET METAL PARTS ONLY .X ± 1.5 .XX ± .75 .XXX ± .25 X° ± .5 ° D. CRONIN DATE -- -- -- -- SIZE FINAL PROTECTIVE FINISH -- 3 Fax (919) 313-5558 A OUTLINE DRAWING, 5050 XM MATERIAL SURFACE FINISH: 1.6 4 0.73 TITLE -- SCALE C 2610-00009 SHEET 16.000 0.73 0.5 REV. DRAWING NO. 2 0.5 0.5 Phone (919) 313-5300 DATE APPROVED 2.8 0.5 3.02 4600 Silicon Drive Durham, N.C 27703 04/9/10 CHECK 3.8 2.8 3.02 DATE DRAWN BY D OF 1 /1 1 5.00 4.8 5.00 C C Top View Bottom View Side View 4.7 3.9 4.8 4.8 3.8 3.8 0.5 0.5 4.7 3.9 0.6 0.6 B B 0.5 4.8 0.4 4.7 0.5 0.4 4.8 0.5 0.4 0.5 2.782 2.782 0.4 0.4 0.4 0.4 UNLESS OTHERWISE SPECIFIED RECOMMENDED STENCIL PATTERN DIMENSIONS ARE IN MILLIMETERS AND AFTER FINISH. SHADED AREA IS OPEN RECOMMENDED STENCIL PATTERN TOLERANCE UNLESS SPECIFIED: SHADED AREA IS OPEN .XX ± .25 0.4 A 4.7 A RECOMMENDED PCB SOLDER PAD Recommended Solder RECOMMENDED PCB PCB SOLDER PAD DATE DRAWN BY D. CRONIN 04/9/10 UNLESSDATE OTHERWISE SPECIFIED DIMENSIONS ARE IN --MILLIMETERS AND AFTER FINISH. APPROVED DATE TOLERANCE UNLESSTITLE SPECIFIED: .XXX ± .125 --.XX ± .25 X° ± .5 ° .XXX ± .125 FOR SHEET METAL PARTS ONLY MATERIAL X° ± .5 ° THIRD .X ±ANGLE 1.5PROJECTION FOR SHEET METAL PARTS ONLY SIZE .XX ± .75 .X ± 1.5 .XXX ± .25 FINAL PROTECTIVE FINISH .XX ± .75 X° ± .5 ° .XXX ± SCALE .25 SURFACE FINISH: 1.6 X° ± .5 ° 16.000 Pad CHECK Recommended Stencil Pattern THIRD ANGLE PROJECTION (Shaded Area Is Open) -- 5 6 4 5 3 4 D. CRONIN -- 460 Du 04/9/10Ph DATE Fa -- OUTLINE --DRAWING, -- -- 6 DATE DRAWN BY CHECK C DATE APPROVED MATERIAL DRAWING NO. 2610-0000 -- FINAL PROTECTIVE FINISH -- 2 SURFACE FINISH: 1.6 3 2 Copyright © 2010-2011 Inc. All rights reserved. The information this document is subject to change without notice. the logo Cree and logoXLamp and XLamp are registered trade2010 Cree, Cree, Inc. All rights reserved. The information in thisindocument is subject to change without notice. Cree, Cree, the Cree are registered trademarks marks ofInc. Cree, Inc. of Cree, 10 SHE 1 xlamp xm-l leds 6 5 4 NOTICE CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION CONTAINED WITHIN ARE THE PROPRIETARY AND NOTICE CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION NOTICE MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY CONTAINED WITHIN ARE THE PROPRIETARY AND CREE CONFIDENTIAL. THIS PLOT AND THE UNAUTHORIZED PERSON WITHOUT THEINFORMATION WRITTEN CONSENT CONFIDENTIAL INFORMATION CREE, INC. THIS PLOT CONTAINED WITHIN AREOF THE PROPRIETARY AND OF CREE INC. MAY NOT BE COPIED, INFORMATION REPRODUCEDOF ORCREE, DISCLOSED TO PLOT ANY CONFIDENTIAL INC. THIS UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY OF CREE INC. UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT 6 5 6 4 5 3 3 4 3 D D 3.0° C 6 3.0° 12.00[.472] 5.50[.217]F NOMINAL 12.00[.472] 12.00[.472] 5.50[.217]F NOMINAL 5.50[.217]F 12.30 [.484] 10.25 NOMINAL MAX [.404] 10.25 12.30 [.484] W E2 12.30 [.484] MAX [.404]10.25 [.404] W MAX E2 W E2 C C 5 3 1.50[.059] D1 1.50[.059] 1.50[.059] D1 D1 4 8.00[.315] P 8.00[.315] 8.00[.315] P P NOTICE NTIAL. THIS PLOT AND THE INFORMATION THIN ARE THE PROPRIETARY AND INFORMATION OF CREE, INC. THIS PLOT OPIED, REPRODUCED OR DISCLOSED TO ANY D PERSON WITHOUTTHE WRITTEN CONSENT BY BY 1 DATE DATE APP'D APP'D DATE APP'D D AoAo -Bo- 5.40mm [.213"] D - 5.40mm 5.40mm [.213"] [.213"] D All dimensions in mm. BoBo -Ko- 5.40mm [.213"] - 5.40mm 3.35mm [.132"] [.213"] KoKo - - 3.35mm [.132"] 3.35mm [.132"] +.10 +.0039 Do1.50 .0591 -.00 -.0000 [ ] +.10 +.0039 Do1.50 .0591 +.10 +.0039 -.00 -.0000 [ ] Do1.50 .0591 -.00 -.0000 [ ] 1.75[.069] E1 1.75[.069] 1.75[.069] E1 E1 P2 2.00[.079] 2.00[.079] P2 4.00[.157] P2 Po 4.00[.157] 4.00[.157] Po Po D 1 POCKET SIZE BY SIZE Ao -POCKET 5.40mm [.213"] POCKET SIZE REV OF CREE INC. 2.00[.079] REVISIONS 2DESCRIPTION REVISIONS REVISIONS DESCRIPTION DESCRIPTION REV REV Tape and Reel 1 2 2 5.40[.213] Bo 5.40[.213] 5.40[.213] Bo Bo 3.0° C C 2 C 1 .36[.014] T .36[.014] Loaded pocket count was T 750 .36[.014] T REVISONS REV BY DATE DDS 11/8/10 DESCRIPTION A APP'D BS B B B 7.0° B 7.0° 5.40[.213] 5.40[.213] 5.40[.213] Ao END 6 8 A 5 A NOTICE A CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION CONTANED WITHIN ARE THE PROPRIETARY AND CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT 6 OF CREE INC. 6 Trailer 160mm (min) of empty pockets sealed with tape (15 pockets min.) D 6 5 5 5 ANODE SIDE Loaded Pockets (1000 Lamps) B B 7.0° 3.35[.132] Ko 3.35[.132] 3.35[.132] Ko Ko Ao D CREE REFERENCE DRAWING FOR TEK-PAK DRAWING 018275 CREE REFERENCE DRAWING FOR TEK-PAK DRAWING 018275 CREE REFERENCE DRAWING FOR TEK-PAK DRAWING 018275 DATE DRAWN BY UNLESS OTHERWISE SPECIFIED 4600 Silicon Drive D. CRONIN 4/23/10 DIMENSIONS ARE IN INCHES Durham, N.C 27703 DATE DRAWN BY CHECK DATE User Feed Direction AND AFTER FINISH. UNLESS OTHERWISE SPECIFIED Phone (919) 313-5300 DATE DRAWN BY 4600 Silicon Drive D. CRONIN 4/23/10 Ao TOLERANCE SPECIFIED: D. CRONIN UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE INUNLESS INCHES Fax (919) 313-5558 Durham, N.C 27703 4600 Silicon Drive 4/23/10 CHECK DATE DIMENSIONS ARE IN INCHES AND AFTER FINISH. .XX ± .01 APPROVED DATE Durham, N.C 27703 4 Phone (919) 313-5300 CHECK DATE TITLE AND AFTER FINISH. .XXXSPECIFIED: ± .005 TOLERANCE UNLESS Phone (919) 313-5300 Fax (919) 313-5558 3.35 1.75 .5 ° APPROVED TOLERANCE UNLESS A .XX ± X° .01± SPECIFIED: DATE Fax (919) 313-5558 CATHODE SIDE THIRD ANGLE PROJECTION START MATERIAL TITLE .XX ± .01 4 2 .XXXSHEET ± METAL .005 DATE FOR PARTS3ONLYAPPROVED TITLE X° ±.XXX A .X .5±±° .005 .06 MATERIAL THIRD ANGLE PROJECTION REV. A DRAWING NO. 2400-00009 X°.XXPARTS ± ± .5 ° SIZE FOR SHEET METAL ONLY .03 THIRD ANGLE PROJECTION MATERIAL FINAL PROTECTIVE FINISH FOR.XSHEET METAL .010ONLY INDEX QTY ITEM COMMENTS ± .XXX .06 ± PARTS REV. DRAWING NO. SIZE .XX .X ± X° ±.03± .06.5 ° REV. NO. SIZE SHEET OF FINISH .XX ± .03 63 FINAL 1SCALE 1 DRAWING 2400-00009-CORE .XXX ± FINISH: .010 C 12 PROTECTIVE SURFACE FINAL PROTECTIVE FINISH DRAWING SCALE 1 /1 X° ±.XXX .5± ° .010 2 2400-00009-REEL SCALE 2 2 SHEET OF1 X° ± .5 ° 3 4 SURFACE FINISH: 63 SCALE SHEET OF / 1 DRAWING SCALE 1 SURFACE FINISH: 63 DRAWING SCALE 1 /1 XM 5050 CARRIER TAPE XMXM 5050 CARRIER TAPE TAPE A 2402-00011 A 5050 CARRIER 2402-00011 A 2402-00011 A A 4 3 4 2 3 1 A 1 2 1 Leader 400mm (min.) of empty pockets with at least 100mm sealed by tape (40 empty pockets min.) D B 12.4 +.2 .0 MEASURED AT HUB C C 330 +.25 -.75 16.4 +0.2 .0 MEASURED AT HUB THIRD ANGLE PROJECTION 6 B UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETERS AND AFTER FINISH. TOLERANCE UNLESS SPECIFIED: .XX ± .25 .XXX ± .125 X° ± .5 ° FOR SHEET METAL PARTS ONLY .X ± 1.5 .XX ± .75 .XXX ± .25 X° ± .5 ° SURFACE FINISH: 5 4 1.6 3 1.9±.4 DATE DRAWN BY D. CRONIN CHECK 21 ±.4 4600 Silicon Drive Durham, N.C 27703 06/08/10 DATE -- Phone (919) 313-5300 -- Fax (919) 313-5558 A DATE APPROVED -- -- MATERIAL -- TITLE 13.1 ±.2 SIZE FINAL PROTECTIVE FINISH -- SCALE XM LOADING SPEC REV. DRAWING NO. C 2402-00012 SHEET 3.000 2 A OF B 1 /1 1 12.4 +1.0 -.5 MEASURED AT EDGE 60° 60° REVISONS REV Cree BY DATE APP'D Copyright © 2010-2011 Inc. All rights reserved. The information this document is subject to change without notice. the logo Cree and logoDESCRIPTION and XLamp are registered trade2010 Cree, Cree, Inc. All rights reserved. The information in thisindocument is subject to change without notice. Cree, Cree, the XLamp are registered trademarks marks ofInc. Cree, Inc. of Cree, A THIRD ANGLE PROJECTION UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES AND AFTER FINISH. TOLERANCE UNLESS SPECIFIED: .XX ± .01 .XXX ± .005 X° ± .5 ° DRAWN BY D. CRONIN CHECK DATE 4600 Silicon Drive Durham, N.C 27703 09/29/09 11 DATE -APPROVED -MATERIAL Phone (919) 313-5300 -- Fax (919) 313-5558 DATE -- TITLE REEL, 13" X 12MM, 3 PIECE SNAP A Dessicant Desiccant xlamp xm-l leds (inside bag) (inside bag) Humidity Indicator Humidity Indicator Card (inside bag)bag) (inside Packaging Vacuum-Sealed Vacuum-Sealed Moisture Barrier Bag Moisture Barrier Bag Vacuum-Sealed Vacuum-Sealed Moisture Barrier Bag Moisture Barrier Bag Label Bin with Cree Bin CREE Code & Barcode Label Code, Qty, Lot # Label CREE Binwith Code Cree Bin & Barcode LabelLot # Code, Qty, Label with Cree Bin Label with Customer P/N, Qty, Lot #, PO## Code, Qty, Lot Label with Cree Bin Label with Customer P/N, Qty,Qty, Lot #, Lot PO # # Code, Patent Label Patent Label Label with Customer Order Code, Qty, Reel ID, PO # Label with Customer Order Code, Qty, Reel ID, PO # Label with Customer Order Code, Qty, Reel ID, PO# Label with Cree Bin Code, Qty, Lot # Copyright © 2010-2011 Inc. All rights reserved. The information this document is subject to change without notice. the logo Cree and logoXLamp and XLamp are registered trade2010 Cree, Cree, Inc. All rights reserved. The information in thisindocument is subject to change without notice. Cree, Cree, the Cree are registered trademarks marks ofInc. Cree, Inc. of Cree, 12