TI100505 (0402) Series SMD MULTILAYER FERRITE CHIP BEADS (HIGH CURRENT) Rev. A A. Electrical Specifications: Impedance (Ω) ±25% @100MHz 10 30 60 120 120 P/N TI100505U100 TI100505U300 TI100505U600 TI100505U121 TI100505Z121 DCR Max. (Ω) 0.030 0.050 0.200 0.200 0.090 I rms. Max. (A) 2.0 2.0 1.0 1.2 1.5 B. Part Number Key: TI 10 05 05 Y XXX IMPEDANCE VALUE MATERIAL CODE: L, U, Z, B or G DIMENSIONS: LENGTH (a) x WIDTH (b) x THICKNESS (c) FAMILY: TI C. Dimensions: mm (Inch) Series a 1.0 (0.039) ±0.1 (0.004) TI100505 (0402) Tol. b 0.5 (0.020) ±0.1 (0.004) c 0.5 (0.020) ±0.1 (0.004) d 0.1 (0.004) e 2.20 (0.087) f 0.70 (0.028) g 0.40 (0.016) Min. Typ. Typ. Typ. D. Materials: ITEM Initial Permeability (µiac): Maximum Permeability (µm): Saturation Flux Density at 10 Oe: Curie Temperature(Tc): Volume Resistivity (ρ): Temperature Coefficient: Density: Frontier Electronics Corp.® http://www.frontierusa.com ------- L 25 125 B 45 125 Material Code G 110 250 U 200 450 Z 500 900 Gauss °C 2000 >200 2000 >200 1700 >130 1400 >100 1500 >130 Ω-m 1/10000°C 100000 10 100000 10 100000 13 100000 5 100000 12 g/cm³ 4.8 4.8 4.8 4.8 4.8 UNIT Page 1 of 2 667 E. Cochran St., Simi Valley, CA 93065 Phone: 1-805-522-9998, Fax: 1-805-522-9989 TI100505 (0402) Series SMD MULTILAYER FERRITE CHIP BEADS (HIGH CURRENT) Rev. A E. Impedance Characteristics of Materials: a. b. c. d. e. f. Z Material is for applications whose blocking regions are near 100 MHz. L Material, an improvement of B Material has sharp impedance characteristic at high frequency. G Material is for application whose signal frequency is far from the cut off region. Suitable for application requires low insertion loss at high frequency. Different materials are available for different application range. With one material, higher impedance has sharper characteristics. Please confirm the signal wave form to choose suitable products. F. General Information: 1. TI100505-yxxx, “TI” = Type, “10” = Length, “05” = Width, “05” = Thickness, “y” = Material, “xxx” = Impedance. 2. Tolerance: ±25% 3. Small and lightweight surface mounting type 4. High-density packaging with a pitch of 2.54 mm (0.1 inch) max. is possible. This series requires less space and have greater EMI suppression effects. 5. Excellent in physical properties, such as terminal strength, flexure strength, soldering resistance and solder-ability. 6. Applicable to both flow and IR reflow soldering. 7. High impedance covers wide frequency ranges. 8. TI series can be used in high current circuits due to its low DC resistance. 9. Operating temperature: -40°C to +125ºC 10. Impedance and Current range: From 10 Ω (2000 mA) to 120 Ω (1200 mA) 11. Unspecified values available on request. 12. MSL: Level 1. G. Applications: 1. 2. 3. 4. 5. Game Consoles Set Top Boxes Cables Modems Computers Mobile Communication Devices (Cell Phones, Radios, etc.) Frontier Electronics Corp.® http://www.frontierusa.com Page 2 of 2 667 E. Cochran St., Simi Valley, CA 93065 Phone: 1-805-522-9998, Fax: 1-805-522-9989