MPE-60S Series Si l O Single Output, 60W 60 Compact, Enclosed AC/DC Power Supplies Electrical Specifications Key Features: Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Input • 60W Output Power Parameter • Universal 85-264 AC Input Input Voltage Range • EN60950 Compliant • Five Single Output Models Input Frequency Input Current • Meets EN55022 Inrush Current • >300 kHour MTBF • Compact Metal Enclosure Safety Ground Leakage Current Min. Typ. 85 120 47 See Model Selection Guide Cold Start, 115 VAC 30.0 Cold Start, 230 VAC 60.0 115 VAC 230 VAC Max. 264 370 63 1.5 3.5 mA Conditions Min. Typ. See Model Selection Guide See Model Selection Guide See Model Selection Guide See Model Selection Guide See Model Selection Guide 115 VAC 12 230 VAC 80 115 VAC 800 230 VAC 300 115 VAC 50 230 VAC 50 ±0.02 Continuous (Autorecovery) See Note 3 115 See Note 4 135 Max. Units Universal Units VAC VDC Hz A Pk Output Parameter Output Voltage Output Current Output Voltage Adjustment Output Voltage Tolerance, See Note 1 Ripple & Noise (20 MHz), See Note 2 RoHS Compliant Conditions Hold-Up Time Set-Up Time Rise Time Temperature Coefficient Short Circuit Protection Over Voltage Protection Overload Protection mSec mSec mSec %/°C 135 165 % Vout % Iout Max. Units General Parameter Isolation Voltage Isolation resistance EMI/RFI MicroPower Direct 292 Page Street Suite D Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: [email protected] W: www.micropowerdirect.com EMC Compliance Conditions Input to Output Input to Ground Output to Ground 500 VDC Conducted Electrostatic Discharge (ESD) RF Field Susceptibility Electrical Fast Transients/Bursts On Mains Surge Switching Frequency Min. 3,000 1,500 500 Typ. VAC 100 MΩ EN 55022; EN 61000-3-2, -3 IEC/EN 61000-4-2, -6, -8, -11 IEC/EN61000-4-3 IEC/EN 61000-4-4 IEC/EN 61000-4-5 50 kHz Environmental Parameter Operating Temperature Range Storage Temperature Range Cooling Humidity Conditions Min. Typ. Max. -10 +25 +60 -20 +85 Free Air Convection (See Derating Curve) RH, Non-condensing 20 90 Ambient Units °C °C % Physical Case Size Case Material Weight 6.26 x 3.82 x 1.50 Inches (159.0 x 97.0 x 38.0 mm) Vented Metal Enclosure 18.0 Oz (0.51 kg) Reliability Specifications Parameter MTBF Safety Standards Vibration Conditions Min. Typ. Max. Units MIL HDBK 217F, 25°C, Gnd Benign 300 kHours IEN 60950, IEC 60950 10~500 Hz, 2G 10 min/1 Cycle. Period of 60 min each along X, Y &Z Axis Model Selection Guide Input Model Number Output Current (A) Voltage (VDC) 115 VAC 230 VAC MPE-60S-05 2.0 1.0 5.0 MPE-60S-12 2.0 1.0 12.0 MPE-60S-15 2.0 1.0 15.0 MPE-60S-24 2.0 1.0 MPE-60S-48 2.0 1.0 Notes: 1. Output voltage tolerance includes the the effects of set point accuracy, line regulation and load regulation. 2. Ripple and noise is measured at 20 MHz bandwidth using a 12 inch twisted pair wire to connect to the power supply terminals. A 0.1 µF and a 47 µF capacitor are connected in parallel as close to the power supply terminals as possible. 3. Overvoltage protection is provided by a “hiccup mode” circuit. The unit recovers automatically when the fault condition is removed. 4. Overload protection is provided by foldback current limiting. The unit recovers automatically when the fault condition is removed. 5. It is recommended that a fuse be used on the input of a power supply for protection. For the MPE-60S series, a 5A/250 VAC slow blow should be used. Range Current (A) Adjust Output Tolerance (%) Ripple & Noise Efficiency (%, Typ) (mV p-p) Rated Range 4.75 - 5.5 12.0 0 to 12.0 ±2.0 120 73 10.8 - 13.2 5.0 0 to 5.0 ±1.0 120 76 13.5 - 16.5 4.0 0 to 4.0 ±1.0 150 77 24.0 21.6 - 26.4 2.5 0 to 2.5 ±1.0 150 79 48.0 42.2 - 52.8 1.3 0 to 1.3 ±1.0 200 80 Mechanical Dimensions Pin Connections Pin Function 1 2 3 4 5 AC-Line AC-Neutral AC-Ground -Vout +Vout Notes: • All dimensions are typical in inches (mm) • Tolerance x.xx = ±0.01 (±0.25) Derating Curve Static Characteristics (24 Vout) MicroPower Direct www.micropowerdirect.com 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: [email protected]