MPD MPE-25S

MPE-25S Series
Si l O
Single
Output, 25W
2
Compact, Enclosed
AC/DC Power Supplies
Electrical Specifications
Key Features:
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Input
• 25W Output Power
Parameter
• Universal 85-264 AC Input
Input Voltage Range
• EN60950 Approved
• Four Single Output Models
Input Frequency
Input Current
• Meets EN55022
Inrush Current
• >325 kHour MTBF
• Compact Metal Enclosure
Safety Ground Leakage Current
Min.
Typ.
85
120
47
See Model Selection Guide
Cold Start, 115 VAC
15.0
Cold Start, 230 VAC
30.0
115 VAC
230 VAC
Max.
264
370
63
0.45
0.75
mA
Conditions
Min.
Typ.
See Model Selection Guide
See Model Selection Guide
See Model Selection Guide
See Model Selection Guide
See Model Selection Guide
115 VAC
12
230 VAC
80
115 VAC
800
230 VAC
300
115 VAC
50
230 VAC
50
±0.02
Continuous (Autorecovery)
See Note 3 115
See Note 4 135
Max.
Units
Universal
Units
VAC
VDC
Hz
A Pk
Output
Parameter
Output Voltage
Output Current
Output Voltage Adjustment
Output Voltage Tolerance, See Note 1
Ripple & Noise (20 MHz) , See Note 2
RoHS Compliant
Conditions
Hold-Up Time
Set-Up Time
Rise Time
Temperature Coefficient
Short Circuit Protection
Over Voltage Protection
Overload Protection
mSec
mSec
mSec
%/°C
135
165
% Vout
% Iout
Max.
Units
General
Parameter
Isolation Voltage
Isolation resistance
EMI/RFI
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
T: (781) 344-8226
F: (781) 344-8481
E: [email protected]
W: www.micropowerdirect.com
EMC Compliance
Conditions
Input to Output
Input to Ground
Output to Ground
500 VDC
Conducted
Electrostatic Discharge (ESD)
RF Field Susceptibility
Electrical Fast Transients/Bursts On Mains
Surge
Switching Frequency
Min.
3,000
1,500
500
Typ.
VAC
100
MΩ
EN 55022; EN 61000-3-2, -3
IEC/EN 61000-4-2, -6, -8, -11
IEC/EN61000-4-3
IEC/EN 61000-4-4
IEC/EN 61000-4-5
56
kHz
Environmental
Parameter
Operating Temperature Range
Storage Temperature Range
Cooling
Humidity
Conditions
Min.
Typ.
Max.
-10
+25
+60
-20
+85
Free Air Convection (See Derating Curve)
RH, Non-condensing
20
90
Ambient
Units
°C
°C
%
Physical
Case Size
Case Material
Weight
3.90 x 3.82 x 1.42 Inches (99.0 x 97.0 x 36.0 mm)
Vented Metal Enclosure
13.7 Oz (0.39 kg)
Reliability Specifications
Parameter
MTBF
Safety Standards
Vibration
Conditions
Min.
Typ.
Max.
Units
MIL HDBK 217F, 25°C, Gnd Benign
325
kHours
IEN 60950, IEC 60950
10~500 Hz, 2G 10 min/1 Cycle. Period of 60 min each along X, Y &Z Axis
Model Selection Guide
Input
Model
Number
Output
Current (A)
Range
Output
Voltage
Tolerance
(%)
5.0
0 to 5.0
±2.0
50
72
2.1
0 to 2.1
±1.0
100
76
13.5 - 16.5
1.7
0 to 1.7
±1.0
100
77
21.6 - 26.4
1.1
0 to 1.1
±1.0
100
80
Voltage (VDC)
115 VAC
230 VAC
MPE-25S-05
0.6
0.35
5.0
4.75 - 5.5
MPE-25S-12
0.6
0.35
12.0
10.8 - 13.2
MPE-25S-15
0.6
0.35
15.0
MPE-25S-24
0.6
0.35
24.0
Notes:
1. Output voltage tolerance includes the the
effects of set point accuracy, line regulation
and load regulation.
2. Ripple and noise is measured at 20 MHz
bandwidth using a 12 inch twisted pair
wire to connect to the power supply terminals. A 0.1 µF and a 47 µF capacitor are
connected in parallel as close to the power
supply terminals as possible.
3. Overvoltage protection is provided by a
“hiccup mode” circuit. The unit recovers
automatically when the fault condition is
removed.
4. Overload protection is provided by foldback current limiting. The unit recovers
automatically when the fault condition
is removed.
5. Efficiency is measured with a 115 VAC
input.
6. It is recommended that a fuse be used on
the input of a power supply for protection.
For the MPE-25S series, a 2.5A/250 VAC
slow blow should be used.
Rated
Current (A)
Adjust
Rated
Ripple &
Noise
Efficiency
(%, Typ)
(mV p-p)
Mechanical Dimensions
Pin Connections
Pin
Function
1
2
3
4
5
-Vout
+Vout
AC-Ground
AC-Line
AC-Neutral
Notes:
• All dimensions are typical in inches (mm)
• Tolerance x.xx = ±0.01 (±0.25)
Derating Curve
Static Characteristics (24 Vout)
MicroPower Direct
www.micropowerdirect.com
292 Page Street Ste D Stoughton, MA 02072
•
TEL: (781) 344-8226
•
FAX: (781) 344-8481
•
E-Mail: [email protected]