RS1-S15 - RSG Electronic Components GmbH

RS1/RD1-S15
1.5 Watt unregulated
single output
4 Pin SIP4 / 8 Pin DIP8 package
1000 VDC isolation up to 3000 VDC isolation
■ Low ripple and noise
■ Efficiency up to 79%
■ -40°C~85°C operation temperature range
■ Non-conductive black plastic case
■
■
OUTPUT SPECIFICATIONS
Voltage accuracy
Line regulation (Per 1% Vin Charge)
Load regulation (From 20% to 100% Load)
(Output 3.3 V Model)
Ripple & Noise (20 MHz bandwith) (1)
Temperature coefficient
Capacitor load (2)
ABSOLUTE MAXIMUM RATINGS (4)
± 3%
± 1.2%
± 10%
± 20%
100 mV pk-pk
± 0.02%/°C
See table
These are stress ratings. Exposure of devices to any of these
conditions may adversely affect long-term reliability.
Input voltage (100 mS)
5 modes
0 ~ 7 VDC
12 modes
0 ~ 15 VDC
24 modes
0 ~ 28 VDC
48 modes (SIP) 0 ~ 54 VDC
Lead soldering temperature
260°C
INPUT SPECIFICATIONS
Voltage range
Max. input current
No-load input current
Input filter
Input reflected ripple current (3)
(1.5 mm from case 10 sec.)
± 10%
See table
See table
Capacitors
20 mA pk-pk
All specifications typical at Ta = 25°C, nominal input voltage and full load
unless otherwise specified.
The information and specifications contained in this data sheet are believed
to be correct at time of publication. However, we accept no responsibility
for consequences arising from printing errors or inaccuracies.
Subject to change without notice.
GENERAL SPECIFICATIONS
NOTE
Efficiency
See table
I/O isolation voltage (3 sec.) Input/Output 1000 ~ 3000 VDC
I/O isolation capacitance
60 pF typ.
I/O isolation resistance
1000 M Ohm
Switching frequency
variable 80 kHz
Humidity
95% rel. H
Reliability calculated MTBF (MIL-HDBK-217F)
> 1.121 Mhrs.
Safety standard (designed to meet)
IEC 60950-1
1) Ripple / Noise measured with 20 MHz bandwith.
2) Tested by minimal Vin and constant resistive load.
3) Measured input reflected ripple current with a simulated
source inductance of 12uH.
4) Exceeding the absolute ratings of the unit could cause
damage. It is not allowed for continuous operating.
5) Operation under no-load conditions will not damage
these devices. However they may not meet all listed
specifications.
PHYSICAL SPECIFICATIONS
Case material
Pin material
Potting material
Weight
Dimensions
Non-conductive black plastic
(UL94V-0 rated)
SIP case > 0.5 mm Alloy42 solder-coated
DIP case > Ø 0.5 mm brass solder-coated
Epoxy (UL94V-0 rated)
SIP > 1.5 g, DIP > 1.8 g
SIP > 0.46“ x 0.24“ x 0.4“
DIP > 0.50“ x 0.40“ x 0.27“
The models listed are just for standard type. If you need a
special specification product, please contact our service.
Phone: +49 69 984047-0, mail to: [email protected]
or use the forms on www.rsg-electronic.de („Kontakt“).
ENVIRONMENT SPECIFICATIONS
Operating temperature (See derating curve)
-40°C~ 85°C
Maximum case temperature
100°C
Storage temperature
-40°C~125°C
Cooling
Nature convection
Page: 1/4
Last update: 03.09.12
RS1-S15
1.5 Watt unregulated
single output
NUMBER STRUCTURE
RS1
-
XX
Name/Package
RS1=SIL4
Input
05=5V
12=12V
24=24V
48=48V
XX
Output
03=3.3V
05=5V
07=7.2V
09=9V
12=12V
15=15V
18=18V
24=24V
DERATING CURVE
S
15
Power
15=1.5W
A
X
Code
internal
Type
S=Single
Isolation
1=1.0 kVDC
3=3.0 kVDC
MODEL SELECTION GUIDE
Model Number
Input
Range VDC
Input current (mA)
No Load / Full Load
Output
VDC
Output current
Full Load (mA)
Efficiency
@FL (%)
Capacitor
Load (HF)
RS1-0503S15AX
RS1-0505S15AX
RS1-0507S15AX
RS1-0509S15AX
RS1-0512S15AX
RS1-0515S15AX
RS1-0518S15AX
RS1-0524S15AX
RS1-1203S15AX
RS1-1205S15AX
RS1-1207S15AX
RS1-1209S15AX
RS1-1212S15AX
RS1-1215S15AX
RS1-1218S15AX
RS1-1224S15AX
RS1-2403S15AX
RS1-2405S15AX
RS1-2407S15AX
RS1-2409S15AX
RS1-2412S15AX
RS1-2415S15AX
RS1-2418S15AX
RS1-2424S15AX
RS1-4803S15AX
RS1-4805S15AX
RS1-4807S15AX
RS1-4809S15AX
RS1-4812S15AX
RS1-4815S15AX
RS1-4818S15AX
RS1-4824S15AX
5
5
5
5
5
5
5
5
12
12
12
12
12
12
12
12
24
24
24
24
24
24
24
24
48
48
48
48
48
48
48
48
30 / 361
30 / 400
30 / 400
30 / 400
30 / 384
30 / 384
30 / 384
30 / 379
15 / 148
15 / 168
15 / 166
15 / 166
15 / 166
15 / 162
15 / 162
15 / 162
10 / 73
10 / 83
10 / 83
10 / 83
10 / 82
10 / 82
10 / 82
10 / 79
6 / 36
6 / 41
6 / 41
6 / 41
6 / 40
6 / 40
6 / 40
6 / 40
3.3
5
7.2
9
12
15
18
24
3.3
5
7.2
9
12
15
18
24
3.3
5
7.2
9
12
15
18
24
3.3
5
7.2
9
12
15
18
24
400
300
208
167
125
100
83
62.5
400
300
208
167
125
100
83
62.5
400
300
208
167
125
100
83
62.5
400
300
208
167
125
100
83
62.5
73
75
75
75
78
78
78
79
74
74
75
75
75
77
77
77
75
75
75
75
76
76
76
79
75
76
76
76
77
77
77
78
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
Page: 2/4
Last update: 03.09.12
RD1-S15
1.5 Watt unregulated
single output
NUMBER STRUCTURE
RD1
-
XX
Name/Package
RD1=DIL8
Input
05=5V
12=12V
24=24V
48=48V
XX
Output
03=3.3V
05=5V
07=7.2V
09=9V
12=12V
15=15V
18=18V
24=24V
DERATING CURVE
S
15
Power
15=1.5W
A
X
Code
internal
Type
S=Single
Isolation
1=1.0 kVDC
3=3.0 kVDC
MODEL SELECTION GUIDE
Model Number
Input
Range VDC
Input current (mA)
No Load / Full Load
Output
VDC
Output current
Full Load (mA)
Efficiency
@FL (%)
Capacitor
Load (HF)
RD1-0503S15AX
RD1-0505S15AX
RD1-0507S15AX
RD1-0509S15AX
RD1-0512S15AX
RD1-0515S15AX
RD1-0518S15AX
RD1-0524S15AX
RD1-1203S15AX
RD1-1205S15AX
RD1-1207S15AX
RD1-1209S15AX
RD1-1212S15AX
RD11215S15AX
RD1-1218S15AX
RD1-1224S15AX
RD1-2403S15AX
RD1-2405S15AX
RD1-2407S15AX
RD1-2409S15AX
RD1-2412S15AX
RD1-2415S15AX
RD1-2418S15AX
RD1-2424S15AX
5
5
5
5
5
5
5
5
12
12
12
12
12
12
12
12
24
24
24
24
24
24
24
24
30 / 361
30 / 400
30 / 400
30 / 400
30 / 384
30 / 384
30 / 384
30 / 379
15 / 148
15 / 168
15 / 166
15 / 166
15 / 166
15 / 162
15 / 162
15 / 162
10 / 73
10 / 83
10 / 83
10 / 83
10 / 82
10 / 82
10 / 82
10 / 79
3.3
5
7.2
9
12
15
18
24
3.3
5
7.2
9
12
15
18
24
3.3
5
7.2
9
12
15
18
24
400
300
208
167
125
100
83
62.5
400
300
208
167
125
100
83
62.5
400
300
208
167
125
100
83
62.5
73
75
75
75
78
78
78
79
74
74
75
75
75
77
77
77
75
75
75
75
76
76
76
79
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
Page: 3/4
Last update: 03.09.12
RS1/RD1-S15
1.5 Watt unregulated
single output
LOADING VS OUTPUT VOLTAGE 5
LOADING VS OUTPUT VOLTAGE 12
Output Voltage
12 MODELS
Output Voltage
5 MODELS
Load
Load
MECHANICAL SPECIFICATIONS 4 Pin SIL
MECHANICAL SPECIFICATIONS 8 Pin DIL
The thickness of 48V
input voltage model is
7.50 (0.29)
PIN CONNECTIONS
Pin Number
Single 4 Pin SIL
Single 8 Pin DIL
1
2
3
4
5
7
-V Input
+V Input
-V Output
+V Output
-V Input
Pin size is 0.5 mm
(0.02“) DIA or
0.50x0.30 mm
(0.02x0.01“)
Notes:
All dimensions are typical in millimeters (inches).
1) Pin diameter: 0.5 ± 0.05 (0.02 ± 0.002)
2) Pin pitch tolerance: ± 0.35 (± 0.014)
3) Case tolerance: ± 0.5 (± 0.02)
+V Input
+V Output
-V Output
Page: 4/4
Last update: 03.09.12
RSG Electronic Components GmbH
Sprendlinger Landstr. 115
D-63069 Offenbach
Tel. +49 69 984047-0
Fax +49 69 984047-77
mail: [email protected]
www.rsg-electronic.de