RS1-S05 - RSG Electronic Components GmbH

RS1/RD1-S05
0.5 Watt unregulated
single output
4 Pin SIP4 / 8 Pin DIP8 package
1000 VDC isolation up to 3000 VDC isolation
■ Low ripple and noise
■ Efficiency up to 78%
■ -40°C~85°C operation temperature range
■ Non-conductive black plastic case
■ EMI complies with EN55022 class B
■
■
OUTPUT SPECIFICATIONS
Voltage accuracy
Line regulation (Per 1% Vin Charge)
Load regulation (From 20% to 100% Load)
(Output 3.3 V Model)
Ripple & Noise (20 MHz bandwith) (1)
Temperature coefficient
Capacitor load (2)
ABSOLUTE MAXIMUM RATINGS (4)
± 3%
± 1.2%
± 10%
± 20%
100 mV pk-pk
± 0.02%/°C
See table
These are stress ratings. Exposure of devices to any of these
conditions may adversely affect long-term reliability.
Input voltage (100 mS)
5 modes
0 ~ 7 VDC
12 modes
0 ~ 15 VDC
24 modes
0 ~ 28 VDC
48 modes (SIP) 0 ~ 54 VDC
Lead soldering temperature
260°C
INPUT SPECIFICATIONS
(1.5 mm from case 10 sec.)
Voltage range
Max. input current
No-load input current
Input filter
Input reflected ripple current (3)
± 10%
See table
See table
Capacitors
20 mA pk-pk
All specifications typical at Ta = 25°C, nominal input voltage and full load
unless otherwise specified.
The information and specifications contained in this data sheet are believed to
be correct at time of publication. However, we accept no responsibility for
consequences arising from printing errors or inaccuracies.
Subject to change without notice.
GENERAL SPECIFICATIONS
NOTE
Efficiency
See table
I/O isolation voltage (3 sec.)
Input / output
1000 ~ 3000 VDC
I/O isolation capacitance
60 pF typ.
I/O isolation resistance
1000 M Ohm
Switching frequency
variable 80 kHz
Humidity
95% rel. H
Reliability calculated MTBF (MIL-HDBK-217F)
> 1.121 Mhrs.
Safety standard (designed to meet)
IEC 60950-1
1) Ripple / Noise measured with 20 MHz bandwith.
2) Tested by minimal Vin and constant resistive load.
3) Measured input reflected ripple current with a simulated
source inductance of 12uH.
4) Exceeding the absolute ratings of the unit could cause
damage. It is not allowed for continuous operating.
5) Operation under no-load conditions will not damage
these devices. However they may not meet all listed
specifications.
6) To reduce converter´s Ripple & Noise it is recommended
to add a 4.7HF ~ 100HF capacitor in output end. For EMI
performance improvement it is recommended to add a
12HH inductor and a 10HF ~ 220HF capacitor in input end.
EMC SPECIFICATIONS
Radiated emmisions
ESD
RS
EN55022
FCC 47 CFR
Part 15 Subpart B
IEC 61000-4-2
IEC 61000-4-3
Class B
Class B
Perf. criteria B
Perf. criteria A
The models listed are just for standard type. If you need a
special specification product, please contact our service.
Phone: +49 69 984047-0, mail to: [email protected]
or use the forms on www.rsg-electronic.de („Kontakt“).
PHYSICAL SPECIFICATIONS
Case material
Non-conductive black plastic
(UL94V-0 rated)
Pin material SIP case > 0.5 mm Alloy42 solder-coated
DIP case > Ø 0.5 mm brass solder-coated
Potting material
Epoxy (UL94V-0 rated)
Weight
SIP > 1.5 g, DIP > 1.8 g
Dimensions
SIP > 0.46“ x 0.24“ x 0.4“
DIP > 0.50“ x 0.40“ x 0.27“
ENVIRONMENT SPECIFICATIONS
Operating temperature
Maximum case temperature
Storage temperature
Cooling
-40°C~ 85°C
(See derating curve)
100°C
-40°C~125°C
Nature convection
Page: 1/4
Last update: 03.09.12
RS1/RD1-S05
0.5 Watt unregulated
single output
NUMBER STRUCTURE
RS1 -
XX
Name/Package
RS1=SIL4
Input
05=5V
12=12V
24=24V
48=48V
XX
Output
03=3.3V
05=5V
07=7.2V
09=9V
12=12V
15=15V
18=18V
24=24V
DERATING CURVE
S
05
A
X
Power
Code
05=0.50W internal
Type
S=Single
Isolation
1=1.0 kVDC
3=3.0 kVDC
MODEL SELECTION GUIDE
Model Number
Input
Range VDC
Input current (mA)
No Load / Full Load
Output
VDC
Output current
Full Load (mA)
Efficiency
@FL (%)
Capacitor
Load (HF)
RS1-0503S05AX
RS1-0505S05AX
RS1-0507S05AX
RS1-0509S05AX
RS1-0512S05AX
RS1-0515S05AX
RS1-0518S05AX
RS1-0524S05AX
RS1-1203S05AX
RS1-1205S05AX
RS1-1207S05AX
RS1-1209S05AX
RS1-1212S05AX
RS1-1215S05AX
RS1-1218S05AX
RS1-1224S05AX
RS1-2403S05AX
RS1-2405S05AX
RS1-2407S05AX
RS1-2409S05AX
RS1-2412S05AX
RS1-2415S05AX
RS1-2418S05AX
RS1-2424S05AX
RS1-4803S05AX
RS1-4805S05AX
RS1-4807S05AX
RS1-4809S05AX
RS1-4812S05AX
RS1-4815S05AX
RS1-4818S05AX
RS1-4824S05AX
5
5
5
5
5
5
5
5
12
12
12
12
12
12
12
12
24
24
24
24
24
24
24
24
48
48
48
48
48
48
48
48
30 / 134
30 / 129
30 / 136
30 / 134
30 / 132
30 / 132
30 / 134
30 / 139
20 / 60
20 / 56
20 / 56
20 / 56
20 / 60
20 / 60
20 / 60
20 / 60
10 / 31
10 / 29
10 / 31
10 / 31
10 / 31
10 / 29
10 / 30
10 / 30
6 / 17
6 / 16
6 / 17
6 / 17
6 / 17
6 / 17
6 / 17
6 / 17
3.3
5
7.2
9
12
15
18
24
3.3
5
7.2
9
12
15
18
24
3.3
5
7.2
9
12
15
18
24
3.3
5
7.2
9
12
15
18
24
151.5
100
69.44
55.55
41.67
33.33
27.77
20.83
151.5
100
69.44
55.55
41.67
33.33
27.77
20.83
151.5
100
69.44
55.55
41.67
33.33
27.77
20.83
151.5
100
69.44
55.55
41.67
33.33
27.77
20.83
75
78
74
75
76
76
75
72
70
74
74
75
70
70
70
70
67
72
67
67
67
72
70
70
62
65
62
62
62
62
62
62
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
Page: 2/4
Last update: 03.09.12
RS1/RD1-S05
0.5 Watt unregulated
single output
NUMBER STRUCTURE
RD1 - XX
XX
Name/Package
RD1=DIL8
Output
03=3.3V
05=5V
07=7.2V
09=9V
12=12V
15=15V
18=18V
24=24V
Input
05=5V
12=12V
24=24V
DERATING CURVE
S
05
A
X
Power
Code
05=0.50W internal
Type
S=Single
Isolation
1=1.0 kVDC
3=3.0 kVDC
MODEL SELECTION GUIDE
Model Number
Input
Range VDC
Input current (mA)
No Load / Full Load
Output
VDC
Output current
Full Load (mA)
Efficiency
@FL (%)
Capacitor
Load (HF)
RD1-0503S05AX
RD1-0505S05AX
RD1-0507S05AX
RD1-0509S05AX
RD1-0512S05AX
RD1-0515S05AX
RD1-0518S05AX
RD1-0524S05AX
RD1-1203S05AX
RD1-1205S05AX
RD1-1207S05AX
RD1-1209S05AX
RD1-1212S05AX
RD1-1215S05AX
RD1-1218S05AX
RD1-1224S05AX
RD1-2403S05AX
RD1-2405S05AX
RD1-2407S05AX
RD1-2409S05AX
RD1-2412S05AX
RD1-2415S05AX
RD1-2418S05AX
RD1-2424S05AX
5
5
5
5
5
5
5
5
12
12
12
12
12
12
12
12
24
24
24
24
24
24
24
24
30 / 134
30 / 129
30 / 134
30 / 134
30 / 132
30 / 132
30 / 134
30 / 139
20 / 60
20 / 56
20 / 58
20 / 56
20 / 60
20 / 60
20 / 60
20 / 60
10 / 31
10 / 29
10 / 31
10 / 31
10 / 31
10 / 31
10 / 31
10 / 31
3.3
5
7.2
9
12
15
18
24
3.3
5
7.2
9
12
15
18
24
3.3
5
7.2
9
12
15
18
24
151.5
100
69.44
55.55
41.67
33.33
27.77
20.83
151.5
100
69.44
55.55
41.67
33.33
27.77
20.83
151.5
100
69.44
55.55
41.67
33.33
27.77
20.83
75
78
75
75
76
76
75
72
70
75
72
75
70
70
70
70
67
72
67
67
67
67
67
67
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
Page: 3/4
Last update: 03.09.12
RS1/RD1-S05
0.5 Watt unregulated
single output
LOADING VS OUTPUT VOLTAGE 05
LOADING VS OUTPUT VOLTAGE 12
Output Voltage
12 MODELS
Output Voltage
05 MODELS
Load
Load
LOADING VS OUTPUT VOLTAGE 24
LOADING VS OUTPUT VOLTAGE 48
Output Voltage
48 MODELS
Output Voltage
24 MODELS
Load
Load
MECHANICAL SPECIFICATIONS 4 Pin SIL
MECHANICAL SPECIFICATIONS 8 Pin DIL
The thickness of 48V
input voltage model is
7.50 (0.29)
Notes:
All dimensions are typical in millimeters (inches).
1) Pin diameter: 0.5 ± 0.05 (0.02 ± 0.002)
2) Pin pitch tolerance: ± 0.35 (± 0.014)
3) Case tolerance: ± 0.5 (± 0.02)
PIN CONNECTIONS
Pin Number
Single 4 Pin SIL
Single 8 Pin DIL
1
2
3
4
5
7
-V Input
+V Input
-V Output
+V Output
-V Input
+V Input
+V Output
-V Output
RSG Electronic Components GmbH
Sprendlinger Landstr. 115
D-63069 Offenbach
Pin size is 0.5 mm
(0.02“) DIA or
0.50x0.30 mm
(0.02x0.01“)
Page: 4/4
Last update: 03.09.12
Tel. +49 69 984047-0
Fax +49 69 984047-77
mail: [email protected]
www.rsg-electronic.de