TDA8547TS 2 × 0.7 W BTL audio amplifier with output

INTEGRATED CIRCUITS
DATA SHEET
TDA8547TS
2 × 0.7 W BTL audio amplifier with
output channel switching
Product specification
Supersedes data of 1997 Oct 14
1998 Apr 01
NXP Semiconductors
Product specification
2 × 0.7 W BTL audio amplifier with
output channel switching
TDA8547TS
FEATURES
GENERAL DESCRIPTION
• Selection between output channels
The TDA8547TS is a two channel audio power amplifier
for an output power of 2 × 0.7 W with a 16 Ω load at a 5 V
supply. At a low supply voltage of 3.3 V an output power of
0.6 W with an 8 Ω load can be obtained. The circuit
contains two BTL amplifiers with a complementary
PNP-NPN output stage and standby/mute logic.
The operating condition of all channels of the device
(standby, mute or on) is externally controlled by the
MODE pin. With the SELECT pin one of the output
channels can be switched in the standby condition. This
feature can be used for loudspeaker selection and also
reduces the quiescent current consumption.
When only one channel is used the maximum output
power is 1.2 W.
• Flexibility in use
• Few external components
• Low saturation voltage of output stage
• Gain can be fixed with external resistors
• Standby mode controlled by CMOS compatible levels
• Low standby current
• No switch-on/switch-off plops
• High supply voltage ripple rejection
• Protected against electrostatic discharge
• Outputs short-circuit safe to ground, VCC and across the
load
• Thermally protected.
APPLICATIONS
• Telecommunication equipment
• Portable consumer products
• Personal computers
• Motor-driver (servo).
QUICK REFERENCE DATA
SYMBOL
PARAMETER
VCC
supply voltage
Iq
quiescent current
Istb
standby current
Po
output power
CONDITIONS
VCC = 5 V; 2 channels
VCC = 5 V; 1 channel
two channels
one channel
THD
total harmonic distortion
SVRR
supply voltage ripple rejection
MIN.
TYP.
MAX.
UNIT
2.2
5
18
V
−
15
22
mA
−
8
12
mA
−
−
10
μA
THD = 10%; RL = 8 Ω; VCC = 3.3 V
0.5
0.6
−
W
THD = 10%; RL = 16 Ω; VCC = 5 V
0.6
0.7
−
W
THD = 10%; RL = 8 Ω; VCC = 5 V
1
1.2
−
W
THD = 10%; RL = 4 Ω; VCC = 3.3 V
1
1.2
−
W
Po = 0.4 W
−
0.15
−
%
50
−
−
dB
ORDERING INFORMATION
TYPE
NUMBER
TDA8547TS
1998 Apr 01
PACKAGE
NAME
DESCRIPTION
SSOP20 plastic shrink small outline package; 20 leads; body width 4.4 mm
2
VERSION
SOT266-1
NXP Semiconductors
Product specification
2 × 0.7 W BTL audio amplifier with
output channel switching
TDA8547TS
BLOCK DIAGRAM
VCC1 VCC2
handbook, full pagewidth
11
20
−
17
IN1−
IN1+
18
−
+
16
OUT1−
R
VCC1
R
−
−
20 kΩ
3
OUT1+
+
20 kΩ
STANDBY/MUTE LOGIC
TDA8547TS
−
14
IN2−
IN2+
13
−
+
15
OUT2−
R
VCC2
R
−
−
20 kΩ
OUT2+
+
5
SVRR
8
20 kΩ
4
MODE
6
SELECT
n.c.
5
STANDBY/MUTE LOGIC
2, 7, 9, 12, 19
1
10
GND1 GND2
Fig.1 Block diagram.
1998 Apr 01
3
MGK984
NXP Semiconductors
Product specification
2 × 0.7 W BTL audio amplifier with
output channel switching
TDA8547TS
PINNING
SYMBOL PIN
DESCRIPTION
GND1
1
ground, channel 1
n.c.
2
not connected
OUT1+
3
positive loudspeaker terminal,
channel 1
MODE
4
operating mode select (standby, mute,
operating)
SVRR
5
half supply voltage, decoupling ripple
rejection
SELECT
6
input for selection of operating channel
n.c.
7
not connected
OUT2+
8
positive loudspeaker terminal,
channel 2
n.c.
9
not connected
GND2
10
ground, channel 2
VCC2
11
supply voltage, channel 2
n.c.
12
not connected
OUT2−
13
negative loudspeaker terminal,
channel 2
IN2−
14
negative input, channel 2
IN2+
15
positive input, channel 2
IN1+
16
positive input, channel 1
IN1−
17
negative input, channel 1
OUT1−
18
negative loudspeaker terminal,
channel 1
n.c.
19
not connected
VCC1
20
supply voltage, channel 1
handbook, halfpage
19 n.c.
n.c. 2
OUT1+ 3
18 OUT1−
MODE 4
17 IN1−
16 IN1+
SVRR 5
TDA8547TS
SELECT 6
15 IN2+
n.c. 7
14 IN2−
OUT2+ 8
13 OUT2−
n.c. 9
12 n.c.
GND2 10
11 VCC2
MGK998
Fig.2 Pin configuration.
FUNCTIONAL DESCRIPTION
transistor. The total voltage loss is <1 V and with a 5 V
supply voltage and a 16 Ω loudspeaker an output power of
0.7 W can be delivered, when two channels are operating.
If only one channel is operating then an output power of
1.2 W can be delivered (5 V, 8 Ω).
The TDA8547TS is a 2 × 0.7 W BTL audio power amplifier
capable of delivering 2 × 0.7 W output power to a 16 Ω
load at THD = 10% using a 5 V power supply. Using the
MODE pin the device can be switched to standby and
mute condition. The device is protected by an internal
thermal shutdown protection mechanism. The gain can be
set within a range from 6 to 30 dB by external feedback
resistors.
MODE pin
The whole device (both channels) is in the standby mode
(with a very low current consumption) if the voltage at the
MODE pin is >(VCC − 0.5 V), or if this pin is floating. At a
MODE voltage level of less than 0.5 V the amplifier is fully
operational. In the range between 1.5 V and VCC − 1.5 V
the amplifier is in mute condition. The mute condition is
useful to suppress plop noise at the output caused by
charging of the input capacitor.
Power amplifier
The power amplifier is a Bridge-Tied Load (BTL) amplifier
with a complementary PNP-NPN output stage.
The voltage loss on the positive supply line is the
saturation voltage of a PNP power transistor, on the
negative side the saturation voltage of a NPN power
1998 Apr 01
20 VCC1
GND1 1
4
NXP Semiconductors
Product specification
2 × 0.7 W BTL audio amplifier with
output channel switching
TDA8547TS
SELECT pin
a HIGH voltage results in a reduction of quiescent current
consumption by a factor of approximately 2.
If the voltage at the SELECT pin is in the range between
1.5 V and VCC − 1.5 V, or if it is kept floating, then both
channels can be operational. If the SELECT pin is set to a
LOW voltage or grounded, then only channel 2 can
operate and the power amplifier of channel 1 will be in the
standby mode. In this case only the loudspeaker at
channel 2 can operate and the loudspeaker at channel 1
will be switched off. If the SELECT pin is set to a
HIGH level or connected to VCC, then only channel 1 can
operate and the power amplifier of channel 2 will be in the
standby mode. In this case only the loudspeaker at
channel 1 can operate and the loudspeaker at channel 2
will be switched off. Setting the SELECT pin to a LOW or
Switching with the SELECT pin during operating is not
plop-free, because the input capacitor of the channel
which is coming out of standby needs to be charged first.
For plop-free channel selecting the device has first to be
set in mute condition with the MODE pin (between 1.5 V
and VCC − 1.5 V), then set the SELECT pin to the new
level, after a delay set the MODE pin to a LOW level.
The delay needed depends on the values of the input
capacitor and the feedback resistors. Time needed is
approx. 10 × C1 × (R1 + R2), so approximately 0.6 s. for
the values in Fig.4.
Table 1 Control pins MODE and SELECT versus status of output channels
Voltage levels at control pins at VP = 5 V; for other supply voltages see Figs. 14 and 15.
STATUS OF OUTPUT
CHANNEL
CONTROL PIN
TYP. Iq
(mA)
MODE
SELECT
HIGH(1)/NC(2)
X(3)
CHANNEL 1 CHANNEL 2
standby
standby
0
HVP(4)
HVP(4)/NC(2)
mute
mute
15
LOW(5)
HVP(4)/NC(2)
on
on
15
HVP(4)/LOW(5)
HIGH(1)
mute/on
standby
8
HVP(4)/LOW(5)
HVP(4)/NC(2)
mute/on
mute/on
15
HVP(4)/LOW(5)
LOW(5)
standby
mute/on
8
MIN.
MAX.
UNIT
Notes
1. HIGH = Vpin > VCC − 0.5 V.
2. NC = not connected or floating.
3. X = don’t care.
4. HVP = 1.5 V < Vpin < VCC − 1.5 V.
5. LOW = Vpin < 0.5 V.
LIMITING VALUES
In accordance with the Absolute Maximum Rating System (IEC 134).
SYMBOL
PARAMETER
VCC
supply voltage
CONDITIONS
operating
−0.3
+18
V
VI
input voltage
−0.3
VCC + 0.3
V
IORM
repetitive peak output current
−
1
A
Tstg
storage temperature
−55
+150
°C
Tamb
operating ambient temperature
−40
+85
°C
VPsc
AC and DC short-circuit safe voltage
−
10
V
Ptot
power dissipation
−
1.1
W
1998 Apr 01
5
NXP Semiconductors
Product specification
2 × 0.7 W BTL audio amplifier with
output channel switching
TDA8547TS
QUALITY SPECIFICATION
In accordance with “SNW-FQ-611-E”.
THERMAL CHARACTERISTICS
SYMBOL
PARAMETER
CONDITIONS
thermal resistance from junction to ambient
Rth(j-a)
in free air
VALUE
UNIT
110
K/W
MGK987
2.0
handbook, halfpage
P
(W)
1.6
1.2
0.8
0.4
0
0
40
80
120
160
Tamb (°C)
Fig.3 Power derating curve.
Table 2
Maximum ambient temperature at different conditions
CONTINUOUS SINE WAVE DRIVEN
VCC
(V)
RL
(Ω)
Po
(W)(1)
3.3
4
1 channel
3.3
4
2 channels
3.3
8
1 channels
0.6
3.3
8
2 channels
2 × 0.6
0.60
84
5
8
1 channel
1.2
0.67
76
5
8
2 channels
2 × 1.2
1.33
−
APPLICATION
Pmax
(W)
Tamb(max)
(°C)
1.2
0.58
86
2 × 1.2
1.12
27
0.3
117
5
16
1 channel
0.7
0.35
112
5
16
2 channels
2 × 0.7
0.70
73
Note
1. At THD = 10%.
1998 Apr 01
6
NXP Semiconductors
Product specification
2 × 0.7 W BTL audio amplifier with
output channel switching
TDA8547TS
DC CHARACTERISTICS
VCC = 5 V; Tamb = 25 °C; RL = 8 Ω; VMODE = 0 V; gain = 20 dB; measured in BTL application circuit Fig.4; unless
otherwise specified.
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
VCC
supply voltage
operating
2.2
5
18
V
Iq
quiescent current
BTL 2 channels;
note 1
−
15
22
mA
BTL 1 channel;
note 1
−
8
12
mA
Istb
standby current
VMODE = VCC
−
−
10
μA
VO
DC output voltage
note 2
−
2.2
−
V
−
−
50
mV
⎪VOUT+ − VOUT−⎪ differential output voltage
offset
IIN+, IIN−
input bias current
VMODE
input voltage MODE pin
−
−
500
nA
operating
0
−
0.5
V
mute
1.5
−
VCC − 1.5 V
standby
VCC − 0.5 −
VCC
V
IMODE
input current MODE pin
0 V < VMODE < VCC
−
−
20
μA
VSELECT
input voltage SELECT pin
channel 1 = standby; 0
channel 2 = on
−
1
V
ISELECT
input current SELECT pin
channel 1 = on;
channel 2 = standby
VCC − 1
−
VCC
V
VSELECT = 0 V
−
−
100
μA
Notes
1. Measured with RL = ∞. With a load connected at the outputs the quiescent current will increase, the maximum of this
increase being equal to the DC output offset voltage divided by RL.
2. The DC output voltage with respect to ground is approximately 0.5VCC.
1998 Apr 01
7
NXP Semiconductors
Product specification
2 × 0.7 W BTL audio amplifier with
output channel switching
TDA8547TS
AC CHARACTERISTICS
VCC = 5 V; Tamb = 25 °C; RL = 8 Ω; f = 1 kHz; VMODE = 0 V; gain = 20 dB; measured in BTL application circuit Fig.4;
unless otherwise specified.
SYMBOL
Po
PARAMETER
output power, one channel
CONDITIONS
MIN.
TYP.
MAX.
UNIT
THD = 10%
1
1.2
−
W
THD = 0.5%
0.6
0.9
−
W
−
0.15
0.3
%
THD
total harmonic distortion
Po = 0.4 W
Gv
closed loop voltage gain
note 1
Zi
differential input impedance
Vno
noise output voltage
SVRR
supply voltage ripple rejection
6
−
30
dB
−
100
−
kΩ
note 2
−
−
100
μV
note 3
50
−
−
dB
note 4
40
−
−
dB
−
−
200
μV
−
−
dB
Vo
output voltage
note 5
αcs
channel separation
VSELECT = 0.5VCC; note 6 40
Notes
R2
1. Gain of the amplifier is 2 × -------- in BTL application circuit Fig.4.
R1
2. The noise output voltage is measured at the output in a frequency range from 20 Hz to 20 kHz (unweighted), with a
source impedance of RS = 0 Ω at the input.
3. Supply voltage ripple rejection is measured at the output, with a source impedance of RS = 0 Ω at the input.
The ripple voltage is a sine wave with a frequency of 1 kHz and an amplitude of 100 mV (RMS), which is applied to
the positive supply rail.
4. Supply voltage ripple rejection is measured at the output, with a source impedance of RS = 0 Ω at the input.
The ripple voltage is a sine wave with a frequency between 100 Hz and 20 kHz and an amplitude of 100 mV (RMS),
which is applied to the positive supply rail.
5. Output voltage in mute position is measured with a 1 V (RMS) input voltage in a bandwidth of 20 Hz to 20 kHz,
so including noise.
6. Channel separation is measured at the output with a source impedance of RS = 0 Ω at the input and a frequency of
1 kHz. The output power in the operating channel is set to 0.5 W.
1998 Apr 01
8
NXP Semiconductors
Product specification
2 × 0.7 W BTL audio amplifier with
output channel switching
TDA8547TS
TEST AND APPLICATION INFORMATION
The quiescent current has been measured without any
load impedance and both channels driven. When one
channel is active the quiescent current will be halved.
The total harmonic distortion as a function of frequency
was measured using a low-pass filter of 80 kHz.
The value of capacitor C3 influences the behaviour of the
SVRR at low frequencies: increasing the value of C3
increases the performance of the SVRR.
The figure of the MODE voltage (VMODE) as a function of
the supply voltage shows three areas; operating, mute
and standby. It shows, that the DC-switching levels of the
mute and standby respectively depend on the supply
voltage level. The figure of the SELECT voltage (VSELECT)
as a function of the supply voltage shows the voltage
levels for switching the channels in the active, mute or
standby mode.
Test conditions
Because the application can be either Bridge-Tied Load
(BTL) or Single-Ended (SE), the curves of each
application are shown separately.
The thermal resistance = 110 K/W for the SSOP20; the
maximum sine wave power dissipation for Tamb = 25 °C
150 – 25
is: ---------------------- = 1.14 W
110
For Tamb = 60 °C the maximum total power dissipation is:
150 – 60
---------------------- = 0.82 W
110
Thermal Design Considerations
SE application
The ‘measured’ thermal resistance of the IC package is
highly dependent on the configuration and size of the
application board. Data may not be comparable between
different Semiconductor manufacturers because the
application boards and test methods are not (yet)
standardized. Also, the thermal performance of packages
for a specific application may be different than presented
here, because the configuration of the application boards
(copper area!) may be different. NXP Semiconductors
uses FR-4 type application boards with 1 oz copper
traces with solder coating.
Tamb = 25 °C if not specially mentioned, VCC = 7.5 V,
f = 1 kHz, RL = 4 Ω, Gv = 20 dB, audio band-pass
22 Hz to 22 kHz.
The SE application circuit is illustrated in Fig.16.
Increasing the value of electrolytic capacitor C3 will result
in a better channel separation. Because the positive
output is not designed for high output current (2 × Io) at
low load impedance (≤16 Ω), the SE application with
output capacitors connected to ground is advised.
The capacitor value of C6/C7 in combination with the load
impedance determines the low frequency behaviour.
The THD as a function of frequency was measured using
a low-pass filter of 80 kHz. The value of capacitor C3
influences the behaviour of the SVRR at low frequencies:
increasing the value of C3 increases the performance of
the SVRR.
The SSOP package has improved thermal conductivity
which reduces the thermal resistance. Using a practical
PCB layout (see Fig.24) with wider copper tracks to the
corner pins and just under the IC, the thermal resistance
from junction to ambient can be reduced to about 80 K/W.
For Tamb = 60 °C the maximum total power dissipation at
150 – 60
this PCB layout is: ---------------------- = 1.12 W
80
General remark
Please note that this two channel IC is mentioned for
application with only one channel active. For that reason
the curves for worst case power dissipation are given for
the condition of only one of the both channels driven with
a 1 kHz sine wave signal.
The frequency characteristic can be adapted by
connecting a small capacitor across the feedback
resistor. To improve the immunity to HF radiation in radio
circuit applications, a small capacitor can be connected in
parallel with the feedback resistor (56 kΩ); this creates a
low-pass filter.
BTL application
Tamb = 25 °C if not specially mentioned, VCC = 5 V,
f = 1 kHz, RL = 8 Ω, Gv = 20 dB, audio band-pass
22 Hz to 22 kHz.
The BTL application circuit is illustrated in Fig.4.
1998 Apr 01
9
NXP Semiconductors
Product specification
2 × 0.7 W BTL audio amplifier with
output channel switching
TDA8547TS
BTL APPLICATION
handbook, full pagewidth
C1
1 μF
R2
R1
50 kΩ
IN1−
10 kΩ
IN1+
Vi1
20
VCC
C5
100 μF
C4
100 nF
11
17
18
OUT1−
16
C3
47 μF
RL1
3
OUT1+
OUT2−
C2
1 μF
R4
R3
50 kΩ
TDA8547TS
IN2−
10 kΩ
IN2+
Vi2
SVRR
MODE
SELECT
14
13
15
OUT2−
RL2
5
8
4
6
1
OUT2+
10
R2
Gain channel 1 = 2 × -------R1
GND
R4
Gain channel 2 = 2 × -------R3
MGK985
Fig.4 BTL application.
MGD890
30
MGK988
10
handbook, halfpage
handbook, halfpage
Iq
(mA)
THD
(%)
(1)
20
1
10
10−1
10−2
10−2
0
0
4
8
12
20
16
VCC (V)
1
Po (W)
f = 1 kHz; Gv = 20 dB.
(1) VCC = 5 V; RL = 8 Ω.
RL = ∞.
Fig.5 Iq as a function of VCC.
1998 Apr 01
10−1
Fig.6 THD as a function of Po.
10
10
NXP Semiconductors
Product specification
2 × 0.7 W BTL audio amplifier with
output channel switching
TDA8547TS
MGK989
10
handbook, halfpage
MGK699
−60
handbook, halfpage
αcs
(dB)
THD
(%)
(1)
−70
1
(2)
(1)
−80
(3)
10−1
−90
10−2
10
102
103
104
f (Hz)
−100
10
105
102
103
104
f (Hz)
105
VCC = 5 V; Vo = 2 V; RL = 8 Ω.
(1) Gv = 30 dB.
(2) Gv = 20 dB.
(3) Gv = 6 dB.
Po = 0.5 W; Gv = 20 dB.
(1) VCC = 5 V; RL = 8 Ω.
Fig.8
Channel separation as a function of
frequency.
Fig.7 THD as a function of frequency.
MGD894
−20
MGK990
2
handbook, halfpage
handbook, halfpage
Po
(W)
SVRR
(dB)
1.5
−40
(1)
(2)
(1)
1
(2)
−60
(3)
0.5
−80
10
102
103
104
f (Hz)
0
105
0
4
8
VCC (V)
VCC = 5 V; RS = 0 Ω; Vr = 100 mV.
(1) Gv = 30 dB.
(2) Gv = 20 dB.
THD = 10%.
(1) RL = 8 Ω.
(2) RL = 16 Ω.
(3) Gv = 6 dB.
Fig.9 SVRR as a function of frequency.
1998 Apr 01
Fig.10 Po as a function of VCC.
11
12
NXP Semiconductors
Product specification
2 × 0.7 W BTL audio amplifier with
output channel switching
TDA8547TS
MGK991
1.5
MGK992
1.5
handbook, halfpage
handbook, halfpage
P
(W)
P
(W)
1.0
1
(2)
(1)
(1)
0.5
0.5
0
4
0
8
VCC (V)
0
12
0.5
0
1
Po (W)
1.5
(1) RL = 8 Ω.
(2) RL = 16 Ω.
Sine wave of 1 kHz.
(1) VCC = 5 V; RL = 8 Ω.
Fig.11 Worst case power dissipation as a function
of VCC (one channel active).
Fig.12 Power dissipation as a function of Po
(one channel active).
MGL211
10
o
(V)
1
MGL210
16
handbook,
V halfpage
handbook, halfpage
VMODE
(V)
12
10−1
standby
10−2
(1)
10−3
(2)
8
(3)
mute
10−4
4
10−5
operating
10−6
10−1
1
10
VMODE (V)
0
102
0
4
8
12
VP (V)
Band-pass = 22 Hz to 22 kHz.
(1) VCC = 3 V.
(2) VCC = 5 V.
(3) VCC = 12 V.
Fig.13 Vo as a function of VMODE.
1998 Apr 01
Fig.14 VMODE as a function of VP.
12
16
NXP Semiconductors
Product specification
2 × 0.7 W BTL audio amplifier with
output channel switching
TDA8547TS
MGK700
20
handbook, full pagewidth
VSELECT
(V)
16
channel 2
standby
12
channel 1 + 2
on
8
VP
channel 1
on
channel 2
on
4
channel 1
standby
0
0
2
4
6
10
8
12
14
16
18
VP (V)
Fig.15 VSELECT as a function of VP.
SE APPLICATION
handbook, full pagewidth
C1
1 μF
R2
R1
100 kΩ
IN1−
10 kΩ
Vi1
IN1+
20
11
17
18
16
R4
R3
10 kΩ
Vi2
OUT1−
C3
47 μF
3
100 kΩ
IN2−
IN2+
SVRR
MODE
SELECT
TDA8547TS
14
13
15
OUT2−
4
6
C7
470 μF
5
8
1
OUT2+
10
GND
MGK986
Fig.16 SE application.
1998 Apr 01
RL1
OUT1+
Gain channel 1 = R2
-------R1
R4
Gain channel 2 = -------R3
VCC
C5
100 μF
C6
470 μF
OUT2−
C2
1 μF
C4
100 nF
13
RL2
20
NXP Semiconductors
Product specification
2 × 0.7 W BTL audio amplifier with
output channel switching
TDA8547TS
MGD899
10
MGD900
10
handbook, halfpage
handbook, halfpage
THD
(%)
THD
(%)
1
1
(1)
(2)
10−1
10−1
(3)
(1)
(2)
(3)
10−2
10−2
10−1
1
Po (W)
10−2
10
10
f = 1 kHz; Gv = 20 dB.
(1) VCC = 7.5 V; RL = 4 Ω.
(2) VCC = 9 V; RL = 8 Ω.
(3) VCC = 12 V; RL = 16 Ω.
102
103
104
f (Hz)
105
Po = 0.5 W; Gv = 20 dB.
(1) VCC = 7.5 V; RL = 4 Ω.
(2) VCC = 9 V; RL = 8 Ω.
(3) VCC = 12 V; RL = 16 Ω.
Fig.17 THD as a function of Po.
Fig.18 THD as a function of frequency.
MGK993
−40
MGD902
−20
handbook, halfpage
handbook, halfpage
αcs
(dB)
SVRR
(dB)
−40
−60
(1)
(2)
(1)
(2)
−80
(3)
(4)
−60
(3)
−100
10
102
103
104
f (Hz)
−80
10
105
Vo = 1 V; Gv = 20 dB.
(1) VCC = 7.5 V; RL = 4 Ω.
(2) VCC = 9 V; RL = 8 Ω.
(3) VCC = 12 V; RL = 16 Ω.
103
104
f (Hz)
105
VCC = 7.5 V; RL = 4 Ω; RS = 0 Ω; Vr = 100 mV.
(1) Gv = 24 dB.
(2) Gv = 20 dB.
(3) Gv = 0 dB.
(4) VCC = 5 V; RL = 32 Ω.
Fig.19 Channel separation as a function of
frequency.
1998 Apr 01
102
Fig.20 SVRR as a function of frequency.
14
NXP Semiconductors
Product specification
2 × 0.7 W BTL audio amplifier with
output channel switching
TDA8547TS
MGK994
2
MGK995
1.5
handbook, halfpage
handbook, halfpage
Po
(W)
P
(W)
1.6
1.0
1.2
(1)
(1)
(2)
(2)
(3)
(3)
0.8
0.5
0.4
0
0
0
4
8
12
VCC (V)
16
0
12
VCC (V)
16
Fig.22 Worst case power dissipation as a function
of VCC (one channel active).
Fig.21 Po as a function of VCC.
MGK996
1.2
handbook, halfpage
P
(W)
(1)
0.8
(2)
(3)
0.4
0
0.4
0.8
1.2
Po (W)
1.6
Sine wave of 1 kHz.
(1) VCC = 12 V; RL = 16 Ω.
(2) VCC = 7.5 V; RL = 4 Ω.
(3) VCC = 9 V; RL = 8 Ω.
Fig.23 Power dissipation as a function of Po
(one channel active).
1998 Apr 01
8
(1) RL = 4 Ω.
(2) RL = 8 Ω.
(3) RL = 16 Ω.
THD = 10%.
(1) RL = 4 Ω.
(2) RL = 8 Ω.
(3) RL = 16 Ω.
0
4
15
NXP Semiconductors
Product specification
2 × 0.7 W BTL audio amplifier with
output channel switching
TDA8547TS
handbook, full pagewidth
a. Top view copper layout.
+VCC
−OUT1
TDA
8542TS
8547TS
GND
+OUT1
100 μF
10 kΩ
100 nF
56 kΩ
IN1
1 μF
10 kΩ
20
MODE
1
11 kΩ
11 kΩ
IN2
11 TDA 10
8542/47TS
47 μF
56 kΩ
SELECT
CIC
Nijmegen
1 μF
−OUT2
+OUT2
MGK997
b. Top view components layout.
Fig.24 Printed-circuit board layout (BTL).
1998 Apr 01
16
NXP Semiconductors
Product specification
2 × 0.7 W BTL audio amplifier with
output channel switching
TDA8547TS
PACKAGE OUTLINE
SSOP20: plastic shrink small outline package; 20 leads; body width 4.4 mm
D
SOT266-1
E
A
X
c
y
HE
v M A
Z
11
20
Q
A2
A
(A 3)
A1
pin 1 index
θ
Lp
L
1
10
detail X
w M
bp
e
0
2.5
5 mm
scale
DIMENSIONS (mm are the original dimensions)
UNIT
A
max.
A1
A2
A3
bp
c
D (1)
E (1)
e
HE
L
Lp
Q
v
w
y
Z (1)
θ
mm
1.5
0.15
0
1.4
1.2
0.25
0.32
0.20
0.20
0.13
6.6
6.4
4.5
4.3
0.65
6.6
6.2
1
0.75
0.45
0.65
0.45
0.2
0.13
0.1
0.48
0.18
10
o
0
Note
1. Plastic or metal protrusions of 0.20 mm maximum per side are not included.
OUTLINE
VERSION
SOT266-1
1998 Apr 01
REFERENCES
IEC
JEDEC
JEITA
EUROPEAN
PROJECTION
ISSUE DATE
99-12-27
03-02-19
MO-152
17
o
NXP Semiconductors
Product specification
2 × 0.7 W BTL audio amplifier with
output channel switching
TDA8547TS
SOLDERING
Several techniques exist for reflowing; for example,
thermal conduction by heated belt. Dwell times vary
between 50 and 300 seconds depending on heating
method. Typical reflow temperatures range from
215 to 250 °C.
Introduction
There is no soldering method that is ideal for all IC
packages. Wave soldering is often preferred when
through-hole and surface mounted components are mixed
on one printed-circuit board. However, wave soldering is
not always suitable for surface mounted ICs, or for
printed-circuits with high population densities. In these
situations reflow soldering is often used.
Preheating is necessary to dry the paste and evaporate
the binding agent. Preheating duration: 45 minutes at
45 °C.
WAVE SOLDERING
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our “IC Package Databook” (order code 9398 652 90011).
Wave soldering techniques can be used for all SO
packages if the following conditions are observed:
• A double-wave (a turbulent wave with high upward
pressure followed by a smooth laminar wave) soldering
technique should be used.
DIP
SOLDERING BY DIPPING OR BY WAVE
• The longitudinal axis of the package footprint must be
parallel to the solder flow.
The maximum permissible temperature of the solder is
260 °C; solder at this temperature must not be in contact
with the joint for more than 5 seconds. The total contact
time of successive solder waves must not exceed
5 seconds.
• The package footprint must incorporate solder thieves at
the downstream end.
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
The device may be mounted up to the seating plane, but
the temperature of the plastic body must not exceed the
specified maximum storage temperature (Tstg max). If the
printed-circuit board has been pre-heated, forced cooling
may be necessary immediately after soldering to keep the
temperature within the permissible limit.
Maximum permissible solder temperature is 260 °C, and
maximum duration of package immersion in solder is
10 seconds, if cooled to less than 150 °C within
6 seconds. Typical dwell time is 4 seconds at 250 °C.
REPAIRING SOLDERED JOINTS
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
Apply a low voltage soldering iron (less than 24 V) to the
lead(s) of the package, below the seating plane or not
more than 2 mm above it. If the temperature of the
soldering iron bit is less than 300 °C it may remain in
contact for up to 10 seconds. If the bit temperature is
between 300 and 400 °C, contact may be up to 5 seconds.
REPAIRING SOLDERED JOINTS
Fix the component by first soldering two diagonallyopposite end leads. Use only a low voltage soldering iron
(less than 24 V) applied to the flat part of the lead. Contact
time must be limited to 10 seconds at up to 300 °C. When
using a dedicated tool, all other leads can be soldered in
one operation within 2 to 5 seconds between
270 and 320 °C.
SO
REFLOW SOLDERING
Reflow soldering techniques are suitable for all SO
packages.
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
1998 Apr 01
18
NXP Semiconductors
Product specification
2 × 0.7 W BTL audio amplifier with
output channel switching
TDA8547TS
DATA SHEET STATUS
DOCUMENT
STATUS(1)
PRODUCT
STATUS(2)
DEFINITION
Objective data sheet
Development
This document contains data from the objective specification for product
development.
Preliminary data sheet
Qualification
This document contains data from the preliminary specification.
Product data sheet
Production
This document contains the product specification.
Notes
1. Please consult the most recently issued document before initiating or completing a design.
2. The product status of device(s) described in this document may have changed since this document was published
and may differ in case of multiple devices. The latest product status information is available on the Internet at
URL http://www.nxp.com.
DISCLAIMERS
property or environmental damage. NXP Semiconductors
accepts no liability for inclusion and/or use of NXP
Semiconductors products in such equipment or
applications and therefore such inclusion and/or use is at
the customer’s own risk.
Limited warranty and liability ⎯ Information in this
document is believed to be accurate and reliable.
However, NXP Semiconductors does not give any
representations or warranties, expressed or implied, as to
the accuracy or completeness of such information and
shall have no liability for the consequences of use of such
information.
Applications ⎯ Applications that are described herein for
any of these products are for illustrative purposes only.
NXP Semiconductors makes no representation or
warranty that such applications will be suitable for the
specified use without further testing or modification.
In no event shall NXP Semiconductors be liable for any
indirect, incidental, punitive, special or consequential
damages (including - without limitation - lost profits, lost
savings, business interruption, costs related to the
removal or replacement of any products or rework
charges) whether or not such damages are based on tort
(including negligence), warranty, breach of contract or any
other legal theory.
Customers are responsible for the design and operation of
their applications and products using NXP
Semiconductors products, and NXP Semiconductors
accepts no liability for any assistance with applications or
customer product design. It is customer’s sole
responsibility to determine whether the NXP
Semiconductors product is suitable and fit for the
customer’s applications and products planned, as well as
for the planned application and use of customer’s third
party customer(s). Customers should provide appropriate
design and operating safeguards to minimize the risks
associated with their applications and products.
Notwithstanding any damages that customer might incur
for any reason whatsoever, NXP Semiconductors’
aggregate and cumulative liability towards customer for
the products described herein shall be limited in
accordance with the Terms and conditions of commercial
sale of NXP Semiconductors.
NXP Semiconductors does not accept any liability related
to any default, damage, costs or problem which is based
on any weakness or default in the customer’s applications
or products, or the application or use by customer’s third
party customer(s). Customer is responsible for doing all
necessary testing for the customer’s applications and
products using NXP Semiconductors products in order to
avoid a default of the applications and the products or of
the application or use by customer’s third party
customer(s). NXP does not accept any liability in this
respect.
Right to make changes ⎯ NXP Semiconductors
reserves the right to make changes to information
published in this document, including without limitation
specifications and product descriptions, at any time and
without notice. This document supersedes and replaces all
information supplied prior to the publication hereof.
Suitability for use ⎯ NXP Semiconductors products are
not designed, authorized or warranted to be suitable for
use in life support, life-critical or safety-critical systems or
equipment, nor in applications where failure or malfunction
of an NXP Semiconductors product can reasonably be
expected to result in personal injury, death or severe
1998 Apr 01
19
NXP Semiconductors
Product specification
2 × 0.7 W BTL audio amplifier with
output channel switching
TDA8547TS
Limiting values ⎯ Stress above one or more limiting
values (as defined in the Absolute Maximum Ratings
System of IEC 60134) will cause permanent damage to
the device. Limiting values are stress ratings only and
(proper) operation of the device at these or any other
conditions above those given in the Recommended
operating conditions section (if present) or the
Characteristics sections of this document is not warranted.
Constant or repeated exposure to limiting values will
permanently and irreversibly affect the quality and
reliability of the device.
Quick reference data ⎯ The Quick reference data is an
extract of the product data given in the Limiting values and
Characteristics sections of this document, and as such is
not complete, exhaustive or legally binding.
Non-automotive qualified products ⎯ Unless this data
sheet expressly states that this specific NXP
Semiconductors product is automotive qualified, the
product is not suitable for automotive use. It is neither
qualified nor tested in accordance with automotive testing
or application requirements. NXP Semiconductors accepts
no liability for inclusion and/or use of non-automotive
qualified products in automotive equipment or
applications.
Terms and conditions of commercial sale ⎯ NXP
Semiconductors products are sold subject to the general
terms and conditions of commercial sale, as published at
http://www.nxp.com/profile/terms, unless otherwise
agreed in a valid written individual agreement. In case an
individual agreement is concluded only the terms and
conditions of the respective agreement shall apply. NXP
Semiconductors hereby expressly objects to applying the
customer’s general terms and conditions with regard to the
purchase of NXP Semiconductors products by customer.
In the event that customer uses the product for design-in
and use in automotive applications to automotive
specifications and standards, customer (a) shall use the
product without NXP Semiconductors’ warranty of the
product for such automotive applications, use and
specifications, and (b) whenever customer uses the
product for automotive applications beyond NXP
Semiconductors’ specifications such use shall be solely at
customer’s own risk, and (c) customer fully indemnifies
NXP Semiconductors for any liability, damages or failed
product claims resulting from customer design and use of
the product for automotive applications beyond NXP
Semiconductors’ standard warranty and NXP
Semiconductors’ product specifications.
No offer to sell or license ⎯ Nothing in this document
may be interpreted or construed as an offer to sell products
that is open for acceptance or the grant, conveyance or
implication of any license under any copyrights, patents or
other industrial or intellectual property rights.
Export control ⎯ This document as well as the item(s)
described herein may be subject to export control
regulations. Export might require a prior authorization from
national authorities.
1998 Apr 01
20
NXP Semiconductors
provides High Performance Mixed Signal and Standard Product
solutions that leverage its leading RF, Analog, Power Management,
Interface, Security and Digital Processing expertise
Customer notification
This data sheet was changed to reflect the new company name NXP Semiconductors, including new legal
definitions and disclaimers. No changes were made to the technical content, except for package outline
drawings which were updated to the latest version.
Contact information
For additional information please visit: http://www.nxp.com
For sales offices addresses send e-mail to: [email protected]
© NXP B.V. 2010
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner.
The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed
without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license
under patent- or other industrial or intellectual property rights.
Printed in The Netherlands
545102/00/02/pp21
Date of release: 1998 Apr 01
Document order number:
9397 750 03347