TFS1576

Filename: tfs 1576.doc
Version 1.4
Vectron International
28.05.2014
Filter specification
TFS 1576
1/5
Measurement condition
Ambient temperature:
Input power level:
Terminating impedance: *
Input:
Output:
23
0
°C
dBm
34 Ω || -0.45 pF
34 Ω || -0.45 pF
Characteristics
Remark:
The reference level for the relative attenuation arel of the TFS1576 is the maximum attenuation in the pass band. The maximum attenuation in the pass band
is defined as the insertion loss ae. The nominal frequency fN is fixed at 1576.9 MHz without any tolerance or limit. The values of relative attenuation arel are
guaranteed for the whole operating temperature range. The frequency shift of the filter in the operating temperature range is included in the production
tolerance scheme.
Data
typ. value
Insertion loss
ae
3.2
Nominal frequency
fN
-
PB
-
Passband
0.6
dB
tolerance / limit
max.
fN
3.5
±
1576.9
MHz
37.5
MHz
dB
max.
30
29
36
31
30
dB
dB
dB
dB
dB
min.
min.
min.
min.
min.
Group delay ripple within PB
5
ns
VSWR within PB
1.5 : 1
max.
2:1
Input power level
-
max.
10
Pass band ripple
MHz
MHz
MHz
MHz
MHz
...
...
...
...
...
1.0
dB
arel
Relative attenuation
1
1300
1710
1716
2490
dB
1300
1444
1716
2490
3200
MHz
MHz
MHz
MHz
MHz
Operating temperature range
OTR
Storage temperature range
Temperature coefficient of frequency
TCf **
20
10
10
10
20
-
-
- 40 °C ... + 85 °C
-
- 40 °C ... + 85 °C
- 72
ppm/K
dB
dB
dB
dB
dB
dBm
-
*) The terminating impedances depend on parasitics and q-values of matching elements and the board used, and are to be understood as reference values
only. Should there be additional questions do not hesitate to ask for an application note or contact our design team.
**) ∆f(Hz) = TCf(ppm/K) x (T-T0) x fTo(MHz)
Generated:
Checked / Approved:
Vectron International GmbH
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice.
No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or
information.
Filename: tfs 1576.doc
Version 1.4
Vectron International
28.05.2014
Filter specification
TFS 1576
2/5
Filter characteristic
insertion loss: -2.45 dB
0
10
0.04
-1
0.035
-2
0.03
-3
0.025
-4
0.02
-5
0.015
-6
0.01
-7
0.005
-8
0
-9
-0.005
-20
S21 in dB
S21 in dB
-10
-30
-40
GDR in •s
0
-50
-60
0
320
640
960
1280
1600
1920
frequency in MHz
2240
2560
2880
-10
1450
3200
1475
1500
1525
1550
1575
1600
1625
1650
1675
-0.01
1700
frequency in MHz
Construction and pin connection
(All dimensions in mm)
5
6
4
1,2 Max.
G76
● E22
1
1
2
3
4
5
6
Ground
Input
Ground
Ground
Output
Ground
Date code:
E
F
G
...
Year + week
2014
2015
2016
3
2
Date code
3
0,75
3,0 +/-0,15
0,30X0,30
1
6
0,6
4
0,6
50 Ohm Test circuit
2
C1
5
SAW
C2
L2
L1
1, 3, 4, 6
Vectron International GmbH
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice.
No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or
information.
Filename: tfs 1576.doc
Version 1.4
Vectron International
28.05.2014
Filter specification
TFS 1576
3/5
Stability characteristics, reliability
After the following tests the filter shall meet the whole specification:
1. Shock:
500g, 1 ms, half sine wave, 3 shocks each plane;
DIN IEC 68 T2 - 27
2. Vibration:
10 Hz to 500 Hz, 0,35 mm or 5 g respectively, 1 octave per min, 10 cycles per plan, 3 plans;
DIN IEC 68 T2 - 6
3. Change of
temperature:
4. Resistance to
solder heat (reflow):
-55 °C to 125°C / 15 min. each / 100 cycles
DIN IEC 68 part 2 – 14 Test N
reflow possible: three times max.;
for temperature conditions refer to the attached "Air reflow temperature conditions" on page 4;
This filter is RoHS compliant (2011/65/EU)
Packing
Tape & Reel:
IEC 286 – 3, with exception of value for N and minimum bending radius;
tape type II, embossed carrier tape with top cover tape on the upper side;
max. pieces of filters per reel:
reel of empty components at start:
reel of empty components at start including leader:
trailer:
9000
min. 300 mm
min. 500 mm
min. 300 mm
Pull Off Direction
Tape (all dimensions in mm)
W
: 8,00 ± 0,3
Po
: 4,00 ± 0,1
Do
: 1,50 +0,1/-0
E
: 1,75 ± 0,1
F
: 3,50 ± 0,05
G(min)
: 0,75
P2
: 2,00 ± 0,05
P1
: 4,00 ± 0,1
D1(min)
: 1,50
Ao
: 3,25 ± 0,1
Bo
: 3,25 ± 0,1
Ct
: 5,5 ± 0,1
P1
Date Code
Po
Do
P2
W
G
Ct
Bo
F
G
E
t
Ko
Typ
PIN Marker
D1
Ao
W 2
Reel (all dimensions in mm)
A
: 330
W1
: 8,4 +1,5/-0
W2(max) : 14,4
N(min)
: 50
C
: 13,0 +0,5/-0,2
C
A
N
W 1
The minimum bending radius is 45 mm.
Vectron International GmbH
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice.
No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or
information.
Filename: tfs 1576.doc
Version 1.4
Vectron International
28.05.2014
Filter specification
TFS 1576
4/5
Air reflow temperature conditions
Conditions
Average ramp-up rate (30°C to 217°C)
> 100°C
> 150°C
> 217°C
Peak temperature
Time within 5°C of actual peak temperature
Cool-down rate (Peak to 50°C)
Time from 30°C to Peak temperature
Exposure
less than 3°C/second
between 300 and 600 seconds
between 240 and 500 seconds
between 30 and 150 seconds
max. 260°C
between 10 and 30 seconds
less than 6°C/second
no greater than 300 seconds
Chip-mount air reflow profile
Temperature / °C
max.
260°C
217°C
max. 300 s
10 ... 30 s
Time / s
30 ... 150 s
Vectron International GmbH
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice.
No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or
information.
Filename: tfs 1576.doc
Vectron International
Version 1.4
Filter specification
28.05.2014
TFS 1576
5/5
History
Version
Reason of Changes
Name
Date
1.0
- Generation of development specification
Strehl
16.05.2007
1.1
- Change construction
Strehl
18.06.2007
1.2
- Add data and filter characteristic
- Generation of filter specification
Strehl
25.07.2007
1.3
- Change input power level
Strehl
27.08.2007
1.4
- Add group delay ripple
- Updated filter characteristic
Noack
28.05.2014
Vectron International GmbH
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice.
No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or
information.