TFS70BT - Vectron International

Filename: TFS70BT.doc
Version 1.1
Vectron International
21.03.2012
Filter specification
TFS 70BT
1/5
Measurement condition
Ambient temperature:
Input power level:
Terminating impedance: *
Input:
Output:
23
0
°C
dBm
106.68 Ω || -57.85 pF
121.17 Ω || -51.00 pF
Characteristics
Remark:
The reference level for the relative attenuation arel of the TFS 70BT is the minimum of the pass band attenuation. This value is defined as the insertion loss
ae. The nominal frequency fN is fixed at 70 MHz without any tolerance. The values of relative attenuation arel are guaranteed for the whole operating
temperature range. The frequency shift of the filter in the operating temperature range is included in the production tolerance scheme.
Data
typ. value
Insertion loss
(reference level)
ae
9.7
Nominal frequency
fN
-
PB
-
Passband
… fN ±
MHz … fN ±
2.5
10.0
arel
MHz
MHz
fN ±
10.0
MHz … fN ±
Group delay ripple within PB
20.0
MHz
Relative attenuation
7.0
Phase linearity within PB
Operating temperature range
OTR
TCf **
±
dB
70
MHz
2.5
MHz
max.
1
dB
0.5
42
dB
dB
max.
min.
1
38
dB
dB
p-p
43
70.0
dB
ns
min.
max.
40
125
dB
ns
p-p
4.3
deg
max.
dB
min.
-88
6.0
10
deg
dB
- 55 °C ... + 125°C
-
Storage temperature range
Temperature coefficient of frequency
fN
12
dB
16
Input/Output return loss
max.
0.5
Pass band ripple
fN
fN ±
dB
tolerance / limit
- 55 °C ... + 125°C
ppm/K
*) The terminating impedances depend on parasitics and q-values of matching elements and the board used, and are to be understood as reference values
only. Should there be additional questions do not hesitate to ask for an application note or contact our design team.
**) ∆f(Hz) = TCf(ppm/K) x (T-T0) x fcat(MHz).
Generated:
Checked / Approved:
Vectron International GmbH
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice.
No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or
information.
Filename: TFS70BT.doc
Version 1.1
Vectron International
21.03.2012
Filter specification
TFS 70BT
2/5
Filter characteristic
0
-8
-1
1.0112
-16
-2
0.9824
-24
-3
0.9536
-32
-4
0.9248
-5
0.896
-6
0.8672
-56
-7
0.8384
-64
-8
0.8096
-40
-48
-72
1.04
0.7808
-9
-80
50
54
58
62
66
70
74
frequency in MHz
78
82
86
90
delay in µs
magnitude in dB
magnitude in dB
insertion loss: -9.70 dB
0
-10
65.11
66.11
67.11
68.11
69.11
70.11
71.11
frequency in MHz
72.11
73.11
74.11
0.752
75.11
Construction and pin connection
(All dimensions in mm)
TFS 70BT
●
B30
1
3
2 Max.
7,3 Max.
9,3 Max.
Date code
1
2
3
4
5
6
7
8
9
10
Input
Input RF Return
Ground
Ground
Ground
Output
Output RF Return
Ground
Ground
Ground
Date code:
B
C
D
...
Year + week
2011
2012
2013
2,54
5,08
0,8
R0
,
3
0,1
0,9
50 Ω Test circuit
1
6
2
7
L1
50 Ω
C1
L2
50 Ω
C2
3, 4, 5, 8, 9, 10
Vectron International GmbH & Co. KG
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without
notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such
product(s) or information.
Filename: TFS70BT.doc
Version 1.1
Vectron International
21.03.2012
Filter specification
TFS 70BT
3/5
Stability characteristics, reliability
After the following tests the filter shall meet the whole specification:
1. Shock:
500g, 1 ms, half sine wave, 3 shocks each plane;
DIN IEC 68 T2 - 27
2. Vibration:
10 Hz to 500 Hz, 0,35 mm or 5 g respectively, 1 octave per min, 10 cycles per plane, 3 planes;
DIN IEC 68 T2 - 6
3. Change of
temperature:
4. Resistance to
solder heat (reflow):
-55 °C to 125°C / 30 min. each / 10 cycles
DIN IEC 68 part 2 – 14 Test N
reflow possible: three times max.;
for temperature conditions refer to the attached "Air reflow temperature conditions" on page 4;
This filter is RoHS compliant (2002/95/EG, 2005/618/EG)
Packing
Tape & Reel:
IEC 286 – 3, with exception of value for N and minimum bending radius;
tape type II, embossed carrier tape with top cover tape on the upper side;
max. pieces of filters per reel:
reel of empty components at start:
reel of empty components at start including leader:
trailer:
2000
min. 300 mm
min. 500 mm
min. 300 mm
Pull Off Direc tion
Tape (all dimensions in mm)
W
:16,00 ± 0,3
Po
:4,00
± 0,1
Do
:1,50
+0,1/-0
E
:1,75
± 0,10
F
:7,50
± 0,10
G(min)
:0,60
P2
:2,00
± 0,1
P1
:12,00 ± 0,1
D1(min)
:1,50
+0,1/-0
Ao
:7,60
± 0,10
Bo
:9,60
± 0,10
Ct
:13,5
P1
t
Po
P2
W
G
Ct
Bo
F
G
E
Do
PIN Marker
Ko
Date Code
Typ
D1
Ao
W 2
Reel (all dimensions in mm)
A
: 330
W1
:16,4
W2(max) :22,4
N(min)
: 50
C
:13,0
C
A
N
W 1
The minimum bending radius is 45 mm.
Vectron International GmbH & Co. KG
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without
notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such
product(s) or information.
Filename: TFS70BT.doc
Version 1.1
Vectron International
21.03.2012
Filter specification
TFS 70BT
4/5
Air reflow temperature conditions
Conditions
Average ramp-up rate (30°C to 217°C)
> 100°C
> 150°C
> 217°C
Peak temperature
Time within 5°C of actual peak temperature
Cool-down rate (Peak to 50°C)
Time from 30°C to Peak temperature
Exposure
less than 3°C/second
between 300 and 600 seconds
between 240 and 500 seconds
between 30 and 150 seconds
max. 260°C
between 10 and 30 seconds
less than 6°C/second
no greater than 300 seconds
Chip-mount air reflow profile
Temperature / °C
max. 260°C
217°C
max. 300 s
10 ... 30 s
Time / s
30 ... 150 s
Vectron International GmbH & Co. KG
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without
notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such
product(s) or information.
Filename: TFS70BT.doc
Vectron International
Version 1.1
Filter specification
21.03.2012
TFS 70BT
5/5
History
Version
Reason of Changes
Name
Date
1.0
- Generation of development specification
TCUK
11.10.2011
1.1
- Add typical values, change development to filter specification
TCUK
21.03.2012
Vectron International GmbH & Co. KG
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without
notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such
product(s) or information.