METALLIZED POLYCARBONATE FILM CAPACITORS HERMETICALLY SEALED - ROUND TUBULAR METALLIZED POLYCARBONATE Self-healing, high reliability High stability Low capacitance change over wide temperature range High volumetric efficiency Precision circuits requiring low losses, light duty, low frequency energy discharge, coupling and decoupling STYLE “L1” Round hermetically sealed tube Ultimate in moisture resistance Compression type glass end seals possess extraordinary immunity to vibration, pressure and temperature changes Encasement-tubular brass, electro-tinned Metallized polycarbonate capacitors in hermetically sealed cases are available in many styles. Please contact factory or representative. SPECIFICATIONS CONSTRUCTION: metallized polycarbonate capacitors are available only in extended foil (non-inductive) construction PACKAGING: round hermetically sealed tubular style, non-magnetic metal tube, with compression glass end seal, axial copperweld leads LEADS: tin or tin/lead plated copper wire is standard and may be soldered or welded in circuit assembly TEMPERATURE RANGE: may be operated at rated DC voltage from -55°C to +125°C without derating voltage ELECTRICAL (NON-DESTRUCTIVE) TEST 1. 2. 3. 4. 5. CAPACITANCE: shall be measured at or referred to 1000 ± 20 Hz at 25 ± 5°C for capacitance values up to and including 1.0 uf. Capacitance values greater than 1.0 mfd shall be measured at 60 ± 6 Hz. Ref: MIL-STD-202E, Method 305 DISSIPATION FACTOR: shall be measured as described for capacitance and shall not exceed 0.3% to 1 mfd, 0.5% greater than 1 mfd. Typical values throughout the temperature range, are given on curves. INSULATION RESISTANCE: shall be measured as follows: 50 - 100V at 25°C 25,000 meg/mfd, need not exceed 50,000 Megohms 200V at 25°C 50,000 meg/mfd, need not exceed 100,000 Megohms Ref: MIL-STD-202E, Method 302 DIELECTRIC STRENGTH: capacitors shall withstand specified DC test potential for one minute through a limiting resistance of 1 ohm/volt Terminal to terminal - 150% of DC rating Terminal to case - 200% of DC rating Ref: MIL-STD-202E, Method 301 DIELECTRIC ABSORPTION: shall not exceed 0.2% when tested to MIL-C-19978D Ref: MIL-C-19978D Electromagnetic Integrated Solutions 8061 Avonia Road ● Fairview ● Pennsylvania ● 16415 Phone: (814) 474-1571 ● Email: [email protected] ● Web: http://eis.apitech.com ENVIRONMENTAL TESTS 1. 2. 3. 4. VIBRATION: capacitors will meet or exceed the requirements of MIL-STD-202E, Method 204 MOISTURE RESISTANCE: capacitors will meet or exceed the requirements of MIL-STD-202E, Method 103B, condition B, with 500 VDC or rated voltage applied, whichever is less LIFE TEST: will withstand 140% of the rated DC voltage at 125°C for 250 hours with not more than one failure in 12 units LEAD PULL TEST: the leads on these capacitors shall withstand a steadily applied axial pull of 5 lbs. for one minute CUSTOM DESIGN Available on short notice -- special shapes, values, characteristics, combination sections and networks. Non-metallic cases or fabricated steel and brass with glass-to-metal seals. Engineering service is expert and prompt. APPLICATIONS Metallized polycarbonate capacitors in Style "L" hermetically sealed tubular cases offer the user the ultimate in insulation resistance. These capacitors will meet the environmental requirements of MIL-C-39022C and moisture resistance per MIL-STD-202E, Method 106D. Metallized polycarbonate capacitors combine the reliability of self-healing action with high dielectric strength and insulation resistance of polycarbonate film. Metallized polycarbonate capacitors are designed primarily for DC application -- blocking, coupling, decoupling, bypass DC line filtering - where RF and audio components are small in comparison to DC rating. However, they have been successfully used in AC power applications such as power factor correction and AC line filtering. Metallized polycarbonate capacitors operate at all temperatures from -55°C to +125°C. APPLICATION GUIDE: [AC VOLTAGE RATING, -55˚C to +125˚C. AMBIENT] EQUIVALENT VAC [RMS] RATING AT VOLTAGE RATING 60 Hz 400 Hz 50V N/A N/A 100V 63 VAC 45 VAC 200V 160 VAC 95 VAC 400V 200 VAC 170 VAC 600V 240 VAC 190 VAC (AC voltage assumed to be pure sine wave) TYPICAL TEMPERATURE CHARACTERISTICS Electromagnetic Integrated Solutions 8061 Avonia Road ● Fairview ● Pennsylvania ● 16415 Phone: (814) 474-1571 ● Email: [email protected] ● Web: http://eis.apitech.com 1000 Hz N/A 40 VAC 80 VAC 140 VAC 160 VAC RL1, DL1, BL1 SERIES – SPECIFICATIONS DIMENSIONS *50 VDC MFD .0010 .0012 .0015 .0018 .0022 .0027 .0033 .0039 .0047 .0056 .0068 .0082 .010 .012 .015 .018 .022 .027 .033 .039 .047 .056 .068 .082 .10 .12 .15 .18 .22 .27 .33 .39 .47 .56 .68 .82 1.0 1.5 2.0 3.0 4.0 5.0 Dia. .195 .195 .195 .195 .195 .195 .195 .195 .195 .195 .195 .195 .195 .195 .195 .195 .155 .195 .195 .195 .195 .195 .195 .195 .195 .235 .235 .235 .235 .235 .312 .312 .312 .312 .400 .400 .400 .400 .400 .500 .500 .500 L 9/16 9/16 9/16 9/16 9/16 9/16 9/16 9/16 9/16 9/16 9/16 9/16 9/16 9/16 9/16 9/16 9/16 9/16 9/16 9/16 9/16 9/16 9/16 9/16 9/16 9/16 9/16 11/16 11/16 11/16 11/16 11/16 11/16 11/16 11/16 11/16 13/16 15/16 15/16 15/16 1-1/8 1-5/16 Part No. RL1A102 RL1A122 RL1A152 RL1A182 RL1A222 RL1A272 RL1A332 RL1A392 RL1A472 RL1A562 RL1A682 RL1A822 RL1A103 RL1A123 RL1A153 RL1A183 RL1A223 RL1A273 RL1A333 RL1A393 RL1A473 RL1A563 RL1A683 RL1A823 RL1A104 RL1A124 RL1A154 RL1A184 RL1A224 RL1A274 RL1A334 RL1A394 RL1A474 RL1A564 RL1A684 RL1A824 RL1A105 RL1A155 RL1A205 RL1A305 RL1A405 RL1A505 **50 – 100 VDC Dia. .195 .195 .195 .195 .195 .195 .195 .195 .195 .195 .195 .195 .195 .195 .195 .195 .195 .195 .195 .195 .235 .235 .235 .235 .235 .312 .312 .312 .312 .312 .312 .312 .312 .400 .400 .400 .400 .500 .562 .562 .670 .670 L 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 13/16 13/16 13/16 13/16 13/16 13/16 13/16 15/16 15/16 1-1/8 1-1/8 1-1/8 1-1/8 1-5/16 1-5/16 1-5/16 1-5/16 1-13/16 1-9/16 1-3/16 Part No. DL1B102 DL1B122 DL1B152 DL1B182 DL1B222 DL1B272 DL1B332 DL1B392 DL1B472 DL1B562 DL1B682 DL1B822 DL1B103 DL1B123 DL1B153 DL1B183 DL1B223 DL1B273 DL1B333 DL1B393 DL1B473 DL1B563 DL1B683 DL1B823 DL1B104 DL1B124 DL1B154 DL1B184 DL1B224 DL1B274 DL1B334 DL1B394 DL1B474 DL1B564 DL1B684 DL1B824 DL1B105 DL1B155 DL1B205 DL1B305 DL1B405 DL1B505 **50 – 200 VDC Dia. .195 .195 .195 .195 .195 .195 .195 .195 .195 .195 .195 .195 .195 .195 .195 .195 .235 .235 .235 .312 .312 .312 .312 .312 .312 .312 .312 .400 .400 .400 .500 .500 .500 .500 .500 .500 .562 .562 .670 670 .750 1.00 L 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 13/16 13/16 13/16 13/16 13/16 15/16 15/16 15/16 1-1/8 15/16 1-1/8 1-1/8 1-5/16 1-5/16 1-5/16 1-5/16 1-9/16 1-9/16 1-13/16 1-13/16 1-9/16 Part No. BL1C102 BL1C122 BL1C152 BL1C182 BL1C222 BL1C272 BL1C332 BL1C392 BL1C472 BL1C562 BL1C682 BL1C822 BL1C103 BL1C123 BL1C153 BL1C183 BL1C223 BL1C273 BL1C333 BL1C393 BL1C473 BL1C563 BL1C683 BL1C823 BL1C104 BL1C124 BL1C154 BL1C184 BL1C224 BL1C274 BL1C334 BL1C394 BL1C474 BL1C564 BL1C684 BL1C824 BL1C105 BL1C155 BL1C205 BL1C305 BL1C405 BL1C505 400 VDC Dia. .195 .195 .195 .195 .195 .195 .195 .195 .195 .195 .235 .235 .235 .235 .235 .235 .235 .312 .312 .312 .312 .312 .312 .400 .400 .400 .500 .500 .562 .562 .562 .670 .670 .670 .750 .750 .750 1.00 1.00 L 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 13/16 13/16 13/16 13/16 13/16 13/16 15/16 15/16 1-1/8 15/16 1-1/8 1-5/16 1-5/16 1-5/16 1-5/16 1-9/16 1-9/16 1-9/16 1-9/16 1-13/16 1-13/16 1-13/16 2-1/16 1-13/16 2-1/16 Higher values or voltages are available. *50 VDC units also available in B and D material. **100 VDC units also available in B material. CASE DIA. .195 .235 THRU .312 .400 THRU 1.0 STYLE W ONLY WIRE LEADS A.W.G. #24 #22 #20 #22 Electromagnetic Integrated Solutions 8061 Avonia Road ● Fairview ● Pennsylvania ● 16415 Phone: (814) 474-1571 ● Email: [email protected] ● Web: http://eis.apitech.com LEADS DIA. .020 .025 .032 .025 600 VDC Part No. BL1E102 BL1E122 BL1E152 BL1E182 BL1E222 BL1E272 BL1E332 BL1E392 BL1E472 BL1E562 BL1E682 BL1E822 BL1E103 BL1E123 BL1E153 BL1E183 BL1E223 BL1E273 BL1E333 BL1E393 BL1E473 BL1E563 BL1E683 BL1E823 BL1E104 BL1E124 BL1E154 BL1E184 BL1E224 BL1E274 BL1E334 BL1E394 BL1E474 BL1E564 BL1E684 BL1E824 BL1E105 BL1E155 BL1E205 Dia. .195 .195 .195 .195 .195 .195 .195 .235 .235 .235 .235 .235 .312 .312 .312 .312 .312 .312 .400 .400 .400 .400 .400 .500 .500 .500 .500 .562 .562 .670 .670 .670 .670 .750 .750 1.00 1.00 1.00 L 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 13/16 13/16 13/16 13/16 13/16 13/16 13/16 15/16 1-1/8 15/16 15/16 1-1/8 1-1/8 1-5/16 1-1/8 1-1/8 1-5/16 1-5/16 1-5/16 1-9/16 1-9/16 1-9/16 1-13/16 1-13/16 2-1/16 2-1/16 1-13/16 1-13/16 2-5/16 Part No. BL1G102 BL1G122 BL1G152 BL1G182 BL1G222 BL1G272 BL1G332 BL1G392 BL1G472 BL1G562 BL1G682 BL1G822 BL1G103 BL1G123 BL1G153 BL1G183 BL1G223 BL1G273 BL1G333 BL1G393 BL1G473 BL1G563 BL1G683 BL1G823 BL1G104 BL1G124 BL1G154 BL1G184 BL1G224 BL1G274 BL1G334 BL1G394 BL1G474 BL1G564 BL1G684 BL1G824 BL1G105 BL1G155