P42TG-xxxxE/Z2:1MLF PMD-SERIES Rev.09-2010 10 Watt Regulated Single and Dual Output 1.5 kV DC I/O Isolation DIP24 Metal Case Continuous Short Circuit Prot. Full SMD Technology Mainzer Straße 151–153 D-55299 Nackenheim Tel. +49 6135 7026-0 Fax: +49 6135 931070 www.peak-electronics.de [email protected] The PMD 10W series P42TG-xxxxE/Z2:1MLF is a family of cost effective 10W single & dual output DC-DC converters. These converters are encapsulated in miniature DIP24 metal case. High performance features: 1500VDC input/output isolation, continuous short circuit protection with automatic restart and tight line / load regulation, high efficiency operation, output voltage accuracy of ±1% maximum. And a wide input of 2:1 All specifications typical at Ta=25°C, nominal input voltage and full load unless otherwise specified Input Specifications Voltage Range Input Filter Input Reflected Ripple Current¹ Start Up Time (nom. Vin and constant resistive load) 2:1 Wide Input Pi Type 20 mA pk-pk 20mS, typ. Output Specifications Voltage Accuracy Short Circuit Protection Line Regulation² Load Regulation3 (Io = 10 - 100%) Cross Regulation3 (Dual Output) Over Current Protection Ripple and Noise (20Mhz bandwidth) Temperature Coefficient Transient Recovery Time4 Transient Response Deviation4 ± 1% Indefinite (hiccup, automatic recovery) ± 0.5% ± 0.5% (2.5, 3.3Vout Models: ± 0.7%) ± 5% 150% of FL, typ. 75 mV pk-pk ± 0.02% / °C 200us, typ ± 3%, max. General Specifications Efficiency I/O Isolation Voltage (3 sec.) I/O Isolation Capacity I/O Isolation Resistance Switching Frequency (typical) Humidity Reliability Calculated MTBF (MIL-HDBK-217F) See Table 1500 VDC 1000 pF, typ. 1000 MOhm 330 kHz 95% rel H > 1 Mhrs Physical Specifications Case Material Potting Material Weight Nickel Coated Copper Epoxy (UL94V-0 rated) ~ 17.0g, typ. Environment Specifications Operating Temperature Maximum Case Temperature Storage Temperature Cooling RoHS Conform -40 to +60°C (ambient) 100°C -40 to +125°C Free Air Convection (10mm distance required) Soldering 260°C, max. (1.5mm from case 10s.) PMD-Series – P42TG-xxxxE/Z2:1MLF – Single and Dual Output – DIP24 - Metal Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 1/3 Selection Guide Single/Dual Output Order # ) A) ) mA A) d (m ad ( (mA ad (m a o ) o d L L a C ) o )5 ll n. (uF (VD o Lo t Full L VDC t Mi t Fu d ( N e n n ) a t g e e e o n n a % r r rre rre ltag or L cy ( Volt Cur Cur t Vo t Cu put Cu acit put put put cien Inpu Inpu In Out Out Out Effi Cap SINGLE OUTPUT P42TG-122R5E2:1MLF P42TG-123R3E2:1MLF P42TG-1205E2:1MLF P42TG-1212E2:1MLF P42TG-1215E2:1MLF P42TG-242R5E2:1MLF P42TG-243R3E2:1MLF P42TG-2405E2:1MLF P42TG-2412E2:1MLF P42TG-2415E2:1MLF P42TG-482R5E2:1MLF P42TG-483R3E2:1MLF P42TG-4805E2:1MLF P42TG-4812E2:1MLF P42TG-4815E2:1MLF 9-18 9-18 9-18 9-18 9-18 18-36 18-36 18-36 18-36 18-36 36-75 36-75 36-75 36-75 36-75 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 791 1006 992 980 958 381 497 479 485 485 191 249 242 245 242 2.5 3.3 5 12 15 2.5 3.3 5 12 15 2.5 3.3 5 12 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 3000 3000 2000 833 667 3000 3000 2000 833 667 3000 3000 2000 833 667 81 84 86 87 89 84 85 89 88 88 84 85 88 87 88 2200 2200 2200 820 470 2200 2200 2200 820 470 2200 2200 2200 820 470 DUAL OUTPUT P42TG-1212Z2:1MLF P42TG-1215Z2:1MLF P42TG-2412Z2:1MLF P42TG-2415Z2:1MLF P42TG-4812Z2:1MLF P42TG-4815Z2:1MLF 9-18 9-18 18-36 18-36 36-75 36-75 10 10 10 10 10 10 980 969 485 474 245 245 ± 12 ± 15 ± 12 ± 15 ± 12 ± 15 0 0 0 0 0 0 ± 416 ± 333 ± 416 ± 333 ± 416 ± 333 87 88 88 90 87 87 ± 220 ± 150 ± 220 ± 150 ± 220 ± 150 If you need other specifications, please enquire. Notes: PMD-Series – P42TG-xxxxE/Z2:1MLF – Single and Dual Output – DIP24 - Metal Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 2/3 Package / Pinning / Derating PIN CONNECTIONS # SINGLE DUAL 2 - Vin - Vin 3 - Vin - Vin 9 Omitted Common 11 N.C. - Vout 14 +Vout +Vout 16 - Vout Common 22 +Vin +Vin 23 +Vin +Vin others Omitted Omitted App Notes: 1 = Measured Input reflected ripple current with a simulated source inductance of 12uH. 2 = Operation between no load and 10% load conditions will not demage the module, but it may not meet all specifications listed 3 = One load is 25% - 100%, the other load is 100%, the output voltage variable rate is within ± 5% 4 = Tested by nominal Vin and 25% load step change (75% - 50% - 25% of Io) 5 = Tested by minimal Vin and constant resistor load. 6 = Input filter components (C1,L) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; all leads should be minimized to decrease radiated noise. 7 = An external filter capacitor (e.g. Nippon-chemi-con KY ser. 220uF/100V) is required if the module has to meet EN61000-4-5. Over Voltage Protection (Zender diode clamp) 2.5 Vout, 3.3 Vout: 3.9 V 5 Vout 6.2 V 12 Vout 15 V 15 Vout 18 V ± 12 Vout ± 15 V ± 15 Vout ± 18 V EMC SPECIFICATIONS Radiated Emissions EN 55022 6 Conducted Emissions EN55022 ESD IEC 61000-4-2 RS IEC 61000-4-3 EFT IEC 61000-4-4 7 Surge IEC 61000-4-5 CS IEC 61000-4-6 PFMF IEC 61000-4-8 PMD-Series – P42TG-xxxxE/Z2:1MLF – Single and Dual Output – DIP24 - Metal Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 3/3 CLASS A CLASS A Perf. Criteria B Perf. Criteria A Perf. Criteria B Perf. Criteria B Perf. Criteria A Perf. Criteria A