Data Sheet

INTEGRATED CIRCUITS
DATA SHEET
TDA3617
Multiple voltage regulator
Product specification
Supersedes data of 2002 Sep 16
2002 Sep 20
Philips Semiconductors
Product specification
Multiple voltage regulator
TDA3617
FEATURES
• Thermal protection
General
• Load dump protection
• Three VP-state controlled regulators
(regulators 1, 2 and 3)
• Foldback current limit protection for
regulators 1, 2 and 3
• DC short-circuit safe to ground and VP for all regulator
outputs.
• Very good stability and noise behaviour
• Separate control pins for switching regulators 1, 2 and 3
• Supply voltage range from −18 to +50 V
GENERAL DESCRIPTION
• Low quiescent current (when regulators 1, 2 and 3 are
switched off)
The TDA3617 is a multiple output voltage regulator with
three independent regulators. It contains:
• High ripple rejection
1. Three fixed voltage regulators with foldback current
protection (regulators 1, 2 and 3)
• Hold output for indicating regulator 1 and/or 2 and/or 3
out-of-regulation.
2. A supply pin that can withstand load dump pulses and
negative supply voltages
Protections
• Reverse polarity safe (down to −18 V without high
reverse current)
3. Independent enable inputs for regulators 1, 2 and 3
• Able to withstand voltages up to 18 V at the outputs
(supply line may be short circuited)
5. A hold output that can be used to interface with a
microprocessor. The hold indicates that the selected
output voltages are available and within their ranges.
4. Local temperature protection for regulator 3
• ESD protection on all pins
QUICK REFERENCE DATA
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
Supply
VP
supply voltage
operating
9.5
14.4
17.5
V
jump start
t ≤ 10 minutes
−
−
30
V
load dump protection
for 50 ms; tr ≥ 2.5 ms
−
−
50
V
standby mode
−
5
40
µA
−
−
175
°C
Iq(tot)
total quiescent current
Tj
junction temperature
Voltage regulators
VREG1
output voltage regulator 1
1 mA ≤ IREG1 ≤ 1.3 A
8.55
9.0
9.45
V
VREG2
output voltage regulator 2
1 mA ≤ IREG2 ≤ 600 mA
4.75
5.0
5.25
V
VREG3
output voltage regulator 3
1 mA ≤ IREG3 ≤ 300 mA
3.14
3.3
3.46
V
ORDERING INFORMATION
TYPE
NUMBER
TDA3617J
2002 Sep 20
PACKAGE
NAME
DBS9P
DESCRIPTION
plastic DIL-bent-SIL power package; 9 leads (lead length 12 mm)
2
VERSION
SOT157-2
Philips Semiconductors
Product specification
Multiple voltage regulator
TDA3617
BLOCK DIAGRAM
handbook, full pagewidth
VP
(14.4 V)
3
TEMPERATURE
LOAD DUMP
PROTECTION
&
REGULATOR 1
&
REGULATOR 2
&
REGULATOR 3
4 (9 V/1.3 A)
REG1
2
Ven1
Ven2
9
Ven3
1
6 (5 V/600 mA)
REG2
5 (3.3 V/300 mA)
7
REG3
HOLD
HOLD
TDA3617
8
MGL589
GND
Fig.1 Block diagram.
PINNING
SYMBOL
PIN
DESCRIPTION
handbook, halfpage
Ven3
1
Ven1
2
VP
3
regulator 1 output
REG1
4
5
regulator 3 output
REG3
5
REG2
6
regulator 2 output
REG2
6
HOLD
7
hold output
HOLD
7
GND
8
ground
Ven2
GND
9
enable regulator 2 input
8
Ven2
9
Ven3
1
enable regulator 3 input
Ven1
2
enable regulator 1 input
VP
3
supply voltage
REG1
4
REG3
TDA3617
MGL590
Fig.2 Pin configuration.
2002 Sep 20
3
Philips Semiconductors
Product specification
Multiple voltage regulator
TDA3617
The TDA3617 has a hold circuit which indicates when one
of the regulators is out-of-regulation. The hold function is
disabled when all the enable inputs are LOW (TDA3617 in
standby mode). The HOLD output (open-collector output)
can be wired OR-ed with other hold outputs of other
regulator parts (e.g. TDA3618). When all the regulators of
the TDA3617 are disabled (switched off), the HOLD output
will be high ohmic. Because of this feature, the hold will not
influence the hold information when wired OR-ed with
other regulator parts.
FUNCTIONAL DESCRIPTION
The TDA3617 is a multiple output voltage regulator with
three independent switchable regulators. When the supply
voltage is available (VP > 4.5 V), regulators 1, 2 and 3 can
be operated by means of three independent enable inputs.
Schmitt trigger functions are included to switch the
regulators off at low battery voltage (VP < 4 V).
A hysteresis is included to avoid random switching.
All output pins are fully protected. The regulators are
protected against load dump (the regulators switch off at
VP > 20 V) and short circuit (foldback current protection).
handbook, full pagewidth
Figure 3 shows the total timing of a semi-on/off logic set.
Figure 4 shows the total timing of the HOLD signal.
load dump
18.0 V
VP
9.4 V
4.5 V
4.0 V
≥1.8 V
enable
regulator 1 ≤1.2 V
9.0 V
regulator 1
0V
≥1.8 V
enable
regulator 2 ≤1.2 V
5.0 V
regulator 2
0V
≥1.8 V
enable
regulator 3 ≤1.2 V
3.3 V
regulator 3
0V
MGL621
Fig.3 Timing diagrams of a semi-on/off logic set.
2002 Sep 20
4
Philips Semiconductors
Product specification
Multiple voltage regulator
TDA3617
load dump
handbook, full pagewidth
VP
enable
regulator
2 and/or 3
enable
regulator 1
regulator
output
2 and/or 3
out of
regulation
out of
regulation
short
circuit
out of
regulation
regulator
output 1
temperature active
protection
>150 °C passive
HOLD
MGL622
Fig.4 Timing diagrams of the HOLD signal.
LIMITING VALUES
In accordance with the Absolute Maximum Rating System (IEC 60134).
SYMBOL
VP
PARAMETER
CONDITIONS
MIN.
MAX.
UNIT
supply voltage
−
17.5
V
jump start
t ≤ 10 minutes
−
30
V
load dump protection
for 50 ms; tr ≥ 2.5 ms
−
50
V
non-operating
−
−18
V
−
62
W
operating
Vbat(rp)
reverse polarity battery voltage
Ptot
total power dissipation
Tstg
storage temperature
non-operating
−55
+150
°C
Tamb
ambient temperature
operating
−40
+85
°C
Tj
junction temperature
operating
−
175
°C
THERMAL CHARACTERISTICS
SYMBOL
PARAMETER
Rth(j-c)
thermal resistance from junction to case
Rth(j-a)
thermal resistance from junction to ambient
CONDITIONS
in free air
QUALITY SPECIFICATION
In accordance with “SNW-FQ-611-E”.
2002 Sep 20
5
VALUE
UNIT
2
K/W
50
K/W
Philips Semiconductors
Product specification
Multiple voltage regulator
TDA3617
CHARACTERISTICS
VP = 14.4 V; Tamb = 25 °C; measured in test circuit of Fig.6; unless otherwise specified.
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
Supplies
VP
supply voltage
operating
Iq(tot)
9.5
14.4
17.5
V
regulators on
note 1
6
−
−
V
jump start
t ≤ 10 minutes
−
−
30
V
load dump protection
for 50 ms; tr ≥ 2.5 ms
−
−
50
V
VP = 12.4 V; note 2
−
5
40
µA
VP = 14.4 V; note 2
−
5
−
µA
total quiescent current
Power supply Schmitt trigger for regulators 1, 2 and 3
Vthr
rising voltage threshold
Ven = 3 V
6.2
6.8
7.5
V
Vthf
falling voltage threshold
Ven = 3 V
4.0
4.5
5.0
V
Vhys
hysteresis
1.5
2.3
3.0
V
+1.2
V
Enable input (regulators 1, 2 and 3)
−0.2
Vi(off)
off-level input voltage
Vi(on)
on-level input voltage
−
1.8
−
V
ILI
input leakage current
Ven = 5 V
5
30
50
µA
IsinkL
LOW-level sink current
VHOLD ≤ 0.8 V
2
−
−
mA
ILO
output leakage current
VHOLD = 5 V
−
0
5
µA
Hold buffer
Regulator 1 (IREG1 = 5 mA)
VREG1(off)
output voltage regulator off
VREG1
output voltage
−
1
400
mV
1 mA ≤ IREG1 ≤ 1.3 A
8.55
9.0
9.45
V
10.5 V ≤ VP ≤ 17.5 V
8.55
9.0
9.45
V
∆VREG1
line regulation
10.5 V ≤ VP ≤ 17.5 V
−
20
50
mV
∆VREGL1
load regulation
1 mA ≤ IREG1 ≤ 1.3 A
−
35
70
mV
IqREG1
quiescent current
IREG1 = 1.3 A
−
45
110
mA
SVRR1
supply voltage ripple
rejection
f = 3 kHz; Vi = 2 V (p-p)
60
70
−
dB
VREG1d
drop-out voltage
IREG1 = 1.3 A; note 3
−
0.5
1
V
IREG1m
current limit
VREG1 > 7.5 V; note 4
1.3
1.4
−
A
IREG1sc
short-circuit current
RL ≤ 0.5 Ω; note 5
250
500
−
mA
αct
cross talk noise
note 6
−
25
150
µV
Schmitt trigger for hold of regulator 1
Vthr
rising threshold voltage of
regulator 1
VP rising
−
VREG1 − 0.15
VREG1 − 0.075 V
Vthf
falling threshold voltage of
regulator 1
VP falling
8.1
VREG1 − 0.35
−
V
Vhys
hysteresis voltage
0.1
0.2
0.3
V
2002 Sep 20
6
Philips Semiconductors
Product specification
Multiple voltage regulator
SYMBOL
TDA3617
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
Regulator 2 (IREG2 = 5 mA)
VREG2(off)
output voltage regulator off
VREG2
output voltage
−
1
400
mV
1 mA ≤ IREG2 ≤ 600 mA
4.75
5.0
5.25
V
8 V ≤ VP ≤ 17.5 V
4.75
5.0
5.25
V
∆VREG2
line regulation
8 V ≤ VP ≤ 17.5 V
−
2
50
mV
∆VREGL2
load regulation
1 mA ≤ IREG2 ≤ 600 mA
−
20
85
mV
IqREG2
quiescent current
IREG2 = 0.4 A
−
10
40
mA
SVRR2
supply voltage ripple
rejection
f = 3 kHz; Vi = 2 V (p-p)
60
70
−
dB
VREG2d
drop-out voltage
IREG2 = 600 mA; VP = 6 V;
note 3
−
1
1.5
V
IREG2m
current limit
VREG2 > 4 V; note 4
0.65
0.8
−
A
IREG2sc
short-circuit current
RL ≤ 0.5 Ω; note 5
100
300
−
mA
αct
cross talk noise
note 6
−
25
150
µV
Schmitt trigger for hold of regulator 2
Vthr
rising threshold voltage of
regulator 2
VP rising
−
VREG2 − 0.15
VREG2 − 0.075 V
Vthf
falling threshold voltage of
regulator 2
VP falling
4.3
VREG2 − 0.35
−
V
Vhys
hysteresis voltage
0.1
0.2
0.3
V
−
1
400
mV
3.14
3.3
3.46
V
Regulator 3 (IREG3 = 5 mA)
VREG3(off)
output voltage regulator off
VREG3
output voltage
5 V ≤ VP ≤ 17.5 V
3.14
3.3
3.46
V
∆VREG3
line regulation
5 V ≤ VP ≤ 17.5 V
−
2
50
mV
∆VREGL3
load regulation
1 mA ≤ IREG3 ≤ 300 mA
−
20
50
mV
IqREG3
quiescent current
IREG3 = 300 mA
−
10
15
mA
SVRR3
supply voltage ripple
rejection
f = 3 kHz; Vi = 2 V (p-p)
60
70
−
dB
IREG3m
current limit
VREG3 > 3 V; note 4
0.35
0.45
−
A
IREG3sc
short circuit current
RL ≤ 0.5 Ω; note 5
15
50
−
mA
αct
cross talk noise
note 6
−
25
150
µV
1 mA ≤ IREG3 ≤ 300 mA
Schmitt trigger for hold of regulator 3
Vthr
rising threshold voltage of
regulator 3
VP rising
−
VREG3 − 0.15
VREG3 − 0.075 V
Vthf
falling threshold voltage of
regulator 2
VP falling
2.7
VREG3 − 0.35
−
V
Vhys
hysteresis voltage
0.1
0.2
0.3
V
Notes
1. Minimum operating voltage, only if VP has exceeded 4.5 V.
2002 Sep 20
7
Philips Semiconductors
Product specification
Multiple voltage regulator
TDA3617
2. The quiescent current is measured in the standby mode. Therefore, the enable inputs of regulators 1, 2 and 3 are
LOW (Ven < 1 V).
3. The drop-out voltage of regulators 1 and 2 is measured between VP and VREG1 or VREG2 respectively.
4. At current limit, IREGmn is held constant (see Fig.5 for the behaviour of IREGmn).
5. The foldback current protection limits the dissipated power at short circuit (see Fig.5).
6. Perform the load regulation test with sine wave load of 10 kHz on the regulator output under test. Measure the RMS
ripple voltage on each of the remaining regulator outputs, using a 80 kHz low-pass filter.
handbook, halfpage
MGL623
9V
handbook, halfpage
VREG2
VREG1
MGL592
5V
1V
2V
IREG2sc
IREG1sc
≥300 mA
≥150 mA
IREG1
a. Regulator 1.
b. Regulator 2.
handbook, halfpage
VREG3
MGL591
3.3 V
1V
≥200 mA
IREG3sc
IREG3m
IREG3
c. Regulator 3.
Fig.5 Foldback current protection for regulators 1, 2 and 3.
2002 Sep 20
IREG2m
IREG2
IREG1m
8
Philips Semiconductors
Product specification
Multiple voltage regulator
TDA3617
TEST AND APPLICATION INFORMATION
Test information
handbook, full pagewidth
VP
C1
220 nF
VP
(1)
3
7
9
6
enable input regulator 2
Ven2
HOLD
regulator 2
TDA3617
enable input regulator 3
5V
C2
47 µF
RL(REG2)
1 kΩ
5
1
regulator 3
3.3 V
C3
47 µF
Ven3
enable input regulator 1
regulator 1
2
4
1 kΩ
9V
C4
47 µF
8
Ven1
RL(REG3)
GND
RL(REG1)
1 kΩ
MGL593
(1) Capacitor not required for stability.
Fig.6 Test circuit.
Application information
STABILITY
NOISE
The regulators are stabilized with the externally connected
output capacitors. The value of the output capacitors can
be selected by referring to the graph illustrated in Fig.7.
Table 1
Noise figures
NOISE FIGURE (µV)(1)
REGULATOR
When an electrolytic capacitor is used, its temperature
behaviour can cause oscillations at Tamb < −20 °C. In this
case, use a tantalum capacitor.
Co = 10 µF Co = 47 µF Co = 100 µF
1
190
170
140
2
120
110
80
3
100
90
70
The two examples on the next page show how an output
capacitor value is selected.
Note
1. Measured at a bandwidth of 200 kHz.
The noise on the supply line depends on the value of the
supply capacitor and is caused by a current noise (output
noise of the regulators is translated to a current noise by
means of the output capacitors). The noise is minimum
when a high frequency capacitor of 220 nF in parallel with
an electrolytic capacitor of 100 µF is connected directly to
pins 3 and 8 (supply and ground).
2002 Sep 20
9
Philips Semiconductors
Product specification
Multiple voltage regulator
TDA3617
Example 1
Regulators 1, 2 and 3 are stabilized with an electrolytic
output capacitor of 220 µF (ESR = 0.15 Ω).
At Tamb = −30 °C the capacitor value is decreased to
73 µF and the ESR is increased to 1.1 Ω. The regulator will
remain stable at Tamb = −30 °C.
MGK612
handbook, halfpage
20
R
(Ω)
15
Example 2
maximum ESR
10
Regulators 1, 2 and 3 are stabilized with an electrolytic
output capacitor of 10 µF (ESR = 3.18 Ω).
At Tamb = −30 °C the capacitor value is decreased to
3.3 µF and the ESR is increased to 23 Ω. The regulator will
be instable at Tamb = −30 °C.
5
0
0.1
Solution
Use a 47 nF HF capacitor in parallel with the output
electrolytic output capacitor. As can be seen from the
graph in Fig.7, the regulators will remain stable with an
output capacitor of 47 nF onwards. The electrolytic output
capacitor is only needed to minimize the output noise.
2002 Sep 20
stable region
Fig.7
10
1
10
C (µF)
100
Curve for selecting the value of output
capacitor for regulator 1.
Philips Semiconductors
Product specification
Multiple voltage regulator
TDA3617
PACKAGE OUTLINE
DBS9P: plastic DIL-bent-SIL power package; 9 leads (lead length 12 mm)
SOT157-2
non-concave
Dh
x
D
Eh
view B: mounting base side
d
A2
B
j
E
A
L3
L
Q
c
1
v M
9
e1
Z
e2
m
w M
bp
e
0
5
10 mm
scale
DIMENSIONS (mm are the original dimensions)
UNIT
A
A2
bp
c
D (1)
d
Dh
E (1)
e
mm
17.0
15.5
4.6
4.4
0.75
0.60
0.48
0.38
24.0
23.6
20.0
19.6
10
12.2
11.8
5.08
e1
e2
2.54 5.08
Eh
j
L
L3
m
Q
v
w
x
Z (1)
6
3.4
3.1
12.4
11.0
2.4
1.6
4.3
2.1
1.8
0.8
0.25
0.03
2.00
1.45
Note
1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.
OUTLINE
VERSION
REFERENCES
IEC
JEDEC
EIAJ
ISSUE DATE
97-12-16
99-12-17
SOT157-2
2002 Sep 20
EUROPEAN
PROJECTION
11
Philips Semiconductors
Product specification
Multiple voltage regulator
TDA3617
The total contact time of successive solder waves must not
exceed 5 seconds.
SOLDERING
Introduction to soldering through-hole mount
packages
The device may be mounted up to the seating plane, but
the temperature of the plastic body must not exceed the
specified maximum storage temperature (Tstg(max)). If the
printed-circuit board has been pre-heated, forced cooling
may be necessary immediately after soldering to keep the
temperature within the permissible limit.
This text gives a brief insight to wave, dip and manual
soldering. A more in-depth account of soldering ICs can be
found in our “Data Handbook IC26; Integrated Circuit
Packages” (document order number 9398 652 90011).
Wave soldering is the preferred method for mounting of
through-hole mount IC packages on a printed-circuit
board.
Manual soldering
Apply the soldering iron (24 V or less) to the lead(s) of the
package, either below the seating plane or not more than
2 mm above it. If the temperature of the soldering iron bit
is less than 300 °C it may remain in contact for up to
10 seconds. If the bit temperature is between
300 and 400 °C, contact may be up to 5 seconds.
Soldering by dipping or by solder wave
The maximum permissible temperature of the solder is
260 °C; solder at this temperature must not be in contact
with the joints for more than 5 seconds.
Suitability of through-hole mount IC packages for dipping and wave soldering methods
SOLDERING METHOD
PACKAGE
DIPPING
DBS, DIP, HDIP, SDIP, SIL
WAVE
suitable(1)
suitable
Note
1. For SDIP packages, the longitudinal axis must be parallel to the transport direction of the printed-circuit board.
2002 Sep 20
12
Philips Semiconductors
Product specification
Multiple voltage regulator
TDA3617
DATA SHEET STATUS
DATA SHEET STATUS(1)
PRODUCT
STATUS(2)
DEFINITIONS
Objective data
Development
This data sheet contains data from the objective specification for product
development. Philips Semiconductors reserves the right to change the
specification in any manner without notice.
Preliminary data
Qualification
This data sheet contains data from the preliminary specification.
Supplementary data will be published at a later date. Philips
Semiconductors reserves the right to change the specification without
notice, in order to improve the design and supply the best possible
product.
Product data
Production
This data sheet contains data from the product specification. Philips
Semiconductors reserves the right to make changes at any time in order
to improve the design, manufacturing and supply. Changes will be
communicated according to the Customer Product/Process Change
Notification (CPCN) procedure SNW-SQ-650A.
Notes
1. Please consult the most recently issued data sheet before initiating or completing a design.
2. The product status of the device(s) described in this data sheet may have changed since this data sheet was
published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com.
DEFINITIONS
DISCLAIMERS
Short-form specification  The data in a short-form
specification is extracted from a full data sheet with the
same type number and title. For detailed information see
the relevant data sheet or data handbook.
Life support applications  These products are not
designed for use in life support appliances, devices, or
systems where malfunction of these products can
reasonably be expected to result in personal injury. Philips
Semiconductors customers using or selling these products
for use in such applications do so at their own risk and
agree to fully indemnify Philips Semiconductors for any
damages resulting from such application.
Limiting values definition  Limiting values given are in
accordance with the Absolute Maximum Rating System
(IEC 60134). Stress above one or more of the limiting
values may cause permanent damage to the device.
These are stress ratings only and operation of the device
at these or at any other conditions above those given in the
Characteristics sections of the specification is not implied.
Exposure to limiting values for extended periods may
affect device reliability.
Right to make changes  Philips Semiconductors
reserves the right to make changes, without notice, in the
products, including circuits, standard cells, and/or
software, described or contained herein in order to
improve design and/or performance. Philips
Semiconductors assumes no responsibility or liability for
the use of any of these products, conveys no licence or title
under any patent, copyright, or mask work right to these
products, and makes no representations or warranties that
these products are free from patent, copyright, or mask
work right infringement, unless otherwise specified.
Application information  Applications that are
described herein for any of these products are for
illustrative purposes only. Philips Semiconductors make
no representation or warranty that such applications will be
suitable for the specified use without further testing or
modification.
2002 Sep 20
13
Philips Semiconductors
Product specification
Multiple voltage regulator
TDA3617
NOTES
2002 Sep 20
14
Philips Semiconductors
Product specification
Multiple voltage regulator
TDA3617
NOTES
2002 Sep 20
15
Philips Semiconductors – a worldwide company
Contact information
For additional information please visit http://www.semiconductors.philips.com.
Fax: +31 40 27 24825
For sales offices addresses send e-mail to: [email protected].
SCA74
© Koninklijke Philips Electronics N.V. 2002
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner.
The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed
without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license
under patent- or other industrial or intellectual property rights.
Printed in The Netherlands
753503/04/pp16
Date of release: 2002
Sep 20
Document order number:
9397 750 10395