Download

5 W AC-DC Power-Supply PAC5BxxSB
●
●
●
●
●
85 … 264 VAC / 100 … 400 VDC universal input
Continuously short circuit and over current protected
Isolation class II
MTBF > 300000 hours
Small outlines
Model guide
Type
PAC5B03SB
PAC5B05SB
PAC5B09SB
PAC5B12SB
PAC5B15SB
PAC5B24SB
Output voltage
Output current range Ripple & noise up to Efficiency typ.@ full
20 MHz
load, Vin 230 VAC
Accuracy
min.
max.
[mVp-p] max.
[%] typ.
[VDC]
[%]
[mA]
[mA]
3.3
±3
100
1000
150
65
5.0
±2
100
1000
150
70
9.0
±2
56
560
150
72
12
±2
42
420
150
74
15
±2
34
340
150
75
24
±2
21
210
150
75
Capacitive load
[µF] max.
2200
1500
680
470
330
100
Specifications
Input
Voltage range
Frequency
Full load input current
Inrush current
Standby power
Recommended fuse
Hold up time
Isolation
Isolation voltage (input to output)
Isolation resistance
Leakage current
Output
Minimum load
Line regulation
Load regulation @ 10 to
100% load change
Temperature coefficient
EMI
85..264 VAC or 100..400 VDC
Power derating see diagram
47 .. 440 Hz
200 mA max @ 115 VAC
100 mA max @ 230 VAC
20 A @ 115 VAC
30 A @ 230 VAC
0.5 W, max.
1 A / 250 V slow blow
20 ms min. @ 115 VAC
80 ms min. @ 230 VAC
3000 VAC (1 minute, <5 mA)
100 MΩ
0.25 mA @ CY 1 nF / 400V
10 %
± 0.5 %, max.
± 1.5 %, max.
0.02 % / °C
Conducted emission
Radiation emission
ESD Electrostatic discharge
RS field susceptibility
EFT Fast transients on mains line
EMC
EMS
Surge
CS
PFM
Voltage dips,
short and interruptions immunity
Protection
Short circuit
Over current
Over temperature
General
Reliability MTBF@ 25°C
Switching frequency
Environmental
Operating temperature
(ambient)
Power derating
Storage temperature
Case surface temperature
Storage humidity
Cooling
Safety approvals
Physical
Dimensions
Weight
Case material
Mounting
Soldering temperature, Time
Continuous, auto recovery
110 % of full load
No
>300000 h
~100 kHz
-40 °C to +85 °C
(with derating, see diagram)
see diagram
-40 °C to +105 °C
100 °C, max.
85 %, max.
Free air convection
EN60950, UL60950
42 x 27 x 11 mm
10 g
UL94V-0
On PCB
Wave 265 °C max., 10 s max.
Manual 370 °C max., 5 s max.
EN55022 (CISPR22), class A (External circuit refer to fig. 2)
EN55022 (CISPR22), class B (External circuit refer to fig. 3)
EN55022 (CISPR22), class B (External circuit refer to fig. 2 and 3)
IEC, EN61000-4-2, contact ± 4 kV perf. criteria B
IEC, EN61000-4-3, 10 V/m perf. criteria A (External circuit refer to fig. 3)
IEC, EN61000-4-4, ± 2 kV, perf. criteria B (External circuit refer to fig. 2)
IEC, EN61000-4-4, ± 4 kV, perf. criteria B (External circuit refer to fig. 3)
IEC, EN61000-4-5, ± 1 kV perf. criteria B (External circuit refer to fig. 3)
IEC, EN61000-4-5, ± 2 kV perf. criteria B (External circuit refer to fig. 3)
IEC, EN61000-4-6, 3 Vrms perf. criteria A (External circuit refer to fig. 3)
IEC, EN61000-4-8, 10 A/m perf. criteria A
IEC, EN61000-4-11, 0…70 % perf. criteria B
1. External electrolytic capacitors are required to models. More details refer to typical applications.
2. Ripple and noise were measured refer to “ripple and noise measure configuration”.
3. All specifications were measured at Ta 25 °C, humidity < 75 %, nominal input voltage (115 VAC or 230 VAC) and rated output
load unless otherwise specified.
4. In this datasheet, all the test methods of indications are based on corporate standards.
5. In applications with high vibration, the product need to be glued for fixing.
Page 1 of 5
Deutschland:
Inselkammerstraße 10
D-82008 Unterhaching
Tel.: 089 614 503-10
E-Mail: [email protected]
Schweiz:
Hochstrasse 355
CH-8200 Schaffhausen
Tel.: 052 647 42 00
E-Mail: [email protected]
5 W AC-DC Power-Supply PAC5BxxSB
Functional diagram
1
Vin (N)
Input
rectifier
3
Vin (L)
Output
rectifier &
filter
DC/DCConverter
14
+ Vout
12
- Vout
5
C1
External
capacitor
7
Application note inadmissible connection
PAC5BxxSB
N
+Vout
~
-Vout
L
=
PE
Regarding EMI is this connection is not recommended
Ripple and noise measure configuration
N
F1
PAC5BxxSB
Rs
C2
C3
Load
14
+Vo
3
Measure points for
oscilloscope probe
-Vo
12
L
1
7 C1
5
CY
Figure 2 EMC application circuit for standard requirement, Class A
N
F1
NTC
Rs
PAC5BxxSB
C2
D1
C3 +Vout
~
L
MOV
U
-Vout
CX
=
C1
CY
For standard EMC requirement, please refer to figure 2, recommended parameters are shown in this table.
Type
F1
MOV
NTC
Rs
CX
CY
C1
C2
PAC5B03SB
PAC5B05SB
220 µF
1A
PAC5B09SB
1 nF,
10 µF,
250V
Type
Type
12 Ω
0.1 µF
time
14D561K 13D-5
2W
275 VAC 400 VAC 400 V
PAC5B12SB
delay
150 µF
PAC5B15SB
PAC5B24SB
C3
D1
SMBJ7.0A
0.1 µF
50 V
ceramic
SMBJ12A
SMBJ20A
SMBJ30A
Page 2 of 5
Deutschland:
Inselkammerstraße 10
D-82008 Unterhaching
Tel.: 089 614 503-10
E-Mail: [email protected]
Schweiz:
Hochstrasse 355
CH-8200 Schaffhausen
Tel.: 052 647 42 00
E-Mail: [email protected]
5 W AC-DC Power-Supply PAC5BxxSB
Recommend PCB layout
Linewidth ≥ 3 mm, line to line distance ≥ 6 mm, line ground distance ≥ 6 mm, unit: mm
Figure 3, EMC application circuit for applications with higher EMC requirement, Class B
PHI-CON input filter module, PN: PIF003A
L F1
PAC5BxxSB
L
LDM
NTC
C2
CY
MOV
U
D1
C3 +Vout
+
CX
-Vout
CY
N
N
LCM
PE
C1
CY
For higher EMC requirement, please refer to figure 3, recommended parameters are shown in this table.
PHI-CON input filter module PIF003A
Type
F1
MOV
LCM
CX
LDM
CY
NTC
C1
C2
PAC5B03SB
470 µF
PAC5B05SB
1 A,
PAC5B09SB
Type
10 µF,
Type
0.1 µF,
1 nF,
250 V
3.5 mH
330 µH
S14K320
275 VAC
400 VAC
13D-5
400 V
Time
PAC5B12SB
330 µF
delay
PAC5B15SB
PAC5B24SB
100 µF
C3
D1
SMBJ7.0A
0.1 µF
50 V
ceramic
SMBJ12A
SMBJ20A
SMBJ30A
Note:
C1 and C2 are electrolytic capacitors. They are required both AC input and DC input. When DC input, C1 is used as EMC filter
capacitor, the value of C1 is recommended to be 10 μF / 400 V. When the input voltage is above 370 VDC, the recommended
value of C1 is 10 μF / 450 V. C2 and C3 are output filter capacitors, they are recommended to be high frequency- and low
impedance capacitors. Capacitance and rated ripple current of capacitors refer to the data sheets provided by the
manufactures. Voltage derating of capacitors should be 80 % or above. C3 is a ceramic capacitor, which is used to filter high
frequency noise. TVS diode D1 is a recommended component to protect post circuits (if the converter fails).
Page 3 of 5
Deutschland:
Inselkammerstraße 10
D-82008 Unterhaching
Tel.: 089 614 503-10
E-Mail: [email protected]
Schweiz:
Hochstrasse 355
CH-8200 Schaffhausen
Tel.: 052 647 42 00
E-Mail: [email protected]
5 W AC-DC Power-Supply PAC5BxxSB
Page 4 of 5
Deutschland:
Inselkammerstraße 10
D-82008 Unterhaching
Tel.: 089 614 503-10
E-Mail: [email protected]
Schweiz:
Hochstrasse 355
CH-8200 Schaffhausen
Tel.: 052 647 42 00
E-Mail: [email protected]
5 W AC-DC Power-Supply PAC5BxxSB
Dimensions
Unit in mm
Pin section tolerance ± 0.1 mm
General tolerances ± 0.5 mm
Pin
1
3
5
7
12
14
Pin connections
Function
AC In (N) or -Vin
AC In (L) or +Vin
+ Capacitor (C1)
- Capacitor (C1)
- DC Out
+ DC Out
PHI-CON is a trademark of HY-LINE Holding.
Only for professional use by professionals! Not for resale or distribution to the general public in any way! Read the instructions for
use carefully before using!
Life Support Policy: HY-LINE does not authorize the use of any of its products for use in life support devices or systems without the
express written approval of an officer of the Company. Life support systems are devices which support or sustain life, and whose
failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected
to result in significant injury to the user. Rev: 04.16 f
Page 5 of 5
Deutschland:
Inselkammerstraße 10
D-82008 Unterhaching
Tel.: 089 614 503-10
E-Mail: [email protected]
Schweiz:
Hochstrasse 355
CH-8200 Schaffhausen
Tel.: 052 647 42 00
E-Mail: [email protected]