5962-09213

REVISIONS
LTR
DESCRIPTION
DATE (YR-MO-DA)
APPROVED
REV
SHEET
REV
SHEET
REV STATUS
REV
OF SHEETS
SHEET
PMIC N/A
PREPARED BY
Gary Zahn
STANDARD
MICROCIRCUIT
DRAWING
THIS DRAWING IS AVAILABLE
FOR USE BY ALL
DEPARTMENTS
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
AMSC N/A
1
2
3
4
5
7
8
9
10
11
12
13
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
http://www.dscc.dla.mil
CHECKED BY
Greg Cecil
APPROVED BY
Charles F. Saffle
DRAWING APPROVAL DATE
11-01-10
REVISION LEVEL
MICROCIRCUIT, HYBRID, LINEAR, POSITIVE,
LOW DROPOUT, ADJUSTABLE VOLTAGE
REGULATOR
SIZE
CAGE CODE
A
67268
SHEET
DSCC FORM 2233
APR 97
6
1 OF
5962-09213
13
5962-E210-09
1. SCOPE
1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A
choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When
available, a choice of radiation hardness assurance levels are reflected in the PIN.
1.2 PIN. The PIN shall be as shown in the following example:
5962



Federal
stock class
designator
\
R



RHA
designator
(see 1.2.1)
09213
01



Device
type
(see 1.2.2)
/
K



Device
class
designator
(see 1.2.3)
X



Case
outline
(see 1.2.4)
X



Lead
finish
(see 1.2.5)
\/
Drawing number
1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA
levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device.
1.2.2 Device type. The device type identify the circuit function as follows:
Device type
01
Generic number
MSK 5972RH
Circuit function
Radiation hardened, 1.5 A, adjustable voltage regulator
1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level. All
levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K, and
E) or QML Listing (Class G and D). The product assurance levels are as follows:
Device class
Device performance documentation
K
Highest reliability class available. This level is intended for use in space
applications.
H
Standard military quality class level. This level is intended for use in applications
where non-space high reliability devices are required.
G
Reduced testing version of the standard military quality class. This level uses the
Class H screening and In-Process Inspections with a possible limited temperature
range, manufacturer specified incoming flow, and the manufacturer guarantees (but
may not test) periodic and conformance inspections (Group A, B, C, and D).
E
Designates devices which are based upon one of the other classes (K, H, or G)
with exception(s) taken to the requirements of that class. These exception(s) must
be specified in the device acquisition document; therefore the acquisition document
should be reviewed to ensure that the exception(s) taken will not adversely affect
system performance.
D
Manufacturer specified quality class. Quality level is defined by the manufacturers
internal, QML certified flow. This product may have a limited temperature range.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-09213
A
REVISION LEVEL
SHEET
2
1.2.4 Case outlines. The case outlines are as designated in MIL-STD-1835 and as follows:
Outline letter
U
X
Y
Z
Descriptive designator
Terminals
Package style
See figure 1
See figure 1
See figure 1
See figure 1
3
3
3
3
Bottom terminal chip carrier, ceramic
TO-257AA with tab, straight leads, glass sealed
TO-257AA with tab, leads formed up, glass sealed
TO-257AA with tab, leads formed down, glass sealed
1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534.
1.3 Absolute maximum ratings. 1/
Supply voltage (VIN - VOUT).........................................................
Output current ............................................................................
Junction temperature (TJ) ..........................................................
Thermal resistance, junction-to-case (JC), TC = +125C:
Case outline U ........................................................................
Case outlines X, Y, and Z .......................................................
Storage temperature ..................................................................
Lead temperature (soldering, 10 seconds).................................
+40 V dc
1.5 A
+150C
3.5C/W
4.5C/W
-65C to +150C
+300C
1.4 Recommended operating conditions.
Supply voltage (VIN - VOUT) ........................................................
Case operating temperature range (TC).....................................
+3.0 V dc to +32 V dc
-55C to +125C
1.5 Radiation features.
Maximum total dose available ..................................................
≥ 100 krads (Si) 2/ 3/ 4/
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part
of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the
solicitation or contract.
DEPARTMENT OF DEFENSE SPECIFICATION
MIL-PRF-38534 - Hybrid Microcircuits, General Specification for.
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-883 - Test Method Standard Microcircuits.
MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines.
DEPARTMENT OF DEFENSE HANDBOOKS
MIL-HDBK-103 - List of Standard Microcircuit Drawings.
MIL-HDBK-780 - Standard Microcircuit Drawings.
(Copies of these documents are available online at https://assist.daps.dla.mil/quicksearch/ or from the Standardization
Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
1/
2/
3/
4/
Stresses above the absolute maximum ratings may cause permanent damage to the device. Extended operation at the
maximum levels may degrade performance and affect reliability.
These parts may be dose rate sensitive in a space environment and may demonstrate enhanced low dose rate effects.
Radiation end-point limits for the noted parameters are guaranteed only for the conditions as specified in MIL-STD-883,
method 1019, condition A. Dose rate shall be in accordance with MIL-STD-883, method 1019, condition A.
Bipolar device types may degrade from displacement damage from radiation which could affect RHA levels. These device
types have not been characterized for displacement damage.
See figure 3.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-09213
A
REVISION LEVEL
SHEET
3
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of
this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
3. REQUIREMENTS
3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in
accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 may include the performance of all tests herein or as
designated in the device manufacturer's Quality Management (QM) plan or as designated for the applicable device class. The
manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as
defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not
affect the form, fit, or function of the device for the applicable device class.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in
MIL-PRF-38534 and herein.
3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein and figure 1.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2.
3.2.3 Radiation exposure circuits. The radiation exposure circuits shall be as specified on figure 3.
3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are
as specified in table I and shall apply over the full specified operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
tests for each subgroup are defined in table I.
3.5 Marking of devices. Marking of devices shall be in accordance with MIL-PRF-38534. The device shall be marked with the
PIN listed in 1.2 herein. In addition, the manufacturer's vendor similar PIN may also be marked.
3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described
herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample,
for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those
which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be
made available to the preparing activity (DLA Land and Maritime-VA) upon request.
3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this
drawing. The certificate of compliance (original copy) submitted to DLA Land and Maritime-VA shall affirm that the
manufacturer's product meets the performance requirements of MIL-PRF-38534 and herein.
3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of
microcircuits delivered to this drawing.
4. VERIFICATION
4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as
modified in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan shall not affect the form,
fit, or function as described herein.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-09213
A
REVISION LEVEL
SHEET
4
TABLE I. Electrical performance characteristics.
Test
Symbol
Conditions 1/ 2/ 3/
-55C  TC +125C
unless otherwise specified
Group A
subgroups
Min
Reference voltage
VREF
3.0 V  (VIN - VOUT)  40 V
1,2,3
01
Adjust pin current
IADJ
2.5 V  (VIN - VOUT)  40 V
1,2,3
01
Adjust pin current
change
IADJ
2.5 V  (VIN - VOUT)  40 V
1
01
2,3
Line regulation
VRLINE
3.0 V  (VIN - VOUT)  40 V
1
01
2,3
M,D,P,L,R 1/
Load regulation
VRLOAD
VIN = VOUT + 3 V, VOUT  5 V,
10 mA  IOUT  1.5 A
1
01
1
01
2,3
M,D,P,L,R 1/
Current limit
ILIM
VIN = VOUT + 5 V
Minimum load current
4/
IMIN
VIN = VOUT = 40 V, TC = +25C
Ripple rejection 4/
RR
VOUT = 10 V, COUT = 10 F,
f = 120 Hz
1/
2/
3/
4/
Limits
Device
type
1
01
1,2,3
01
1
01
1,2,3
01
1.20
Unit
Max
1.30
V
100
A
-5
5
A
-6
6
-0.02
0.02
-0.05
0.05
-0.03
0.03
-20
20
-50
50
-60
60
1.5
%/V
mV
A
5
66
mA
dB
Device type 01 has been characterized through all levels M, D, P, L, R of irradiation and tested to 1.5 times
at the R level. Pre and post irradiation values are identical unless otherwise specified in table I. When performing post
irradiation electrical measurements for any RHA level, TC = +25C.
Unless otherwise specified, VIN = VOUT + 5 V, IOUT = 10 mA, COUT = 10 F.
These parts may be dose rate sensitive in a space environment and may demonstrate enhanced low dose rate effects.
Radiation end-point limits for the noted parameters are guaranteed only for the conditions as specified in MIL-STD-883,
method 1019, condition A.
Guaranteed by design but not tested. Parameter shall be tested as part of the initial characterization and after design
and process changes. Parameter shall be guaranteed to limits specified in table I for all lots not specifically tested.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-09213
A
REVISION LEVEL
SHEET
5
Case outline U.
Symbol
A
A1
b
b1
b2
b3
D
D1
E
e
S1
S2
Millimeters
Min
Max
--3.30
0.305
0.457
9.27
9.78
10.29
10.80
3.30
3.81
3.86
4.11
15.62
16.13
0.76
11.18
11.68
0.89
0.81
1.07
1.14
1.40
Inches
Min
--.012
.365
.405
.130
.152
.615
.030
.440
.035
.032
.045
Max
.130
.018
.385
.425
.150
.162
.635
.460
.042
.055
NOTES:
1. The U.S. government preferred system of measurement is the metric SI. This item was designed using inch-pound
units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inchpound units shall rule.
2. Lead identification for reference only.
3. Case outline U weight: 2.2 grams typical.
FIGURE 1. Case outlines.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-09213
A
REVISION LEVEL
SHEET
6
Case outline X.
Symbol
A
A1
A2
øb
D
D1/E
e
e1
L
L1
øP
S1
Millimeters
Min
Max
--5.33
0.89
1.14
2.79
3.30
0.71
0.81
16.26
16.76
10.29
10.80
2.54 TYP
5.08 REF
10.16
--13.39
13.64
3.56
3.81
2.73 REF
Inches
Min
Max
--.210
.035
.045
.110
.130
.028
.032
.640
.660
.405
.425
.100 TYP
.200 REF
.400
--.527
.537
.140
.150
.1075 REF
NOTES:
1. Pin 1 is indicated by the ESD marking on the package. Pin numbers are for reference only.
2. The U. S. Government preferred system of measurement is the metric SI. This item was designed using inch-pound
units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the
inch-pound units shall take precedence.
3. Case outline X weight: 3.2 grams typical.
FIGURE 1. Case outlines- Continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-09213
A
REVISION LEVEL
SHEET
7
Case outline Y.
Symbol
A
A1
A2
øb
D
D1/E
e
e1
L
L1
L2
øP
S1
Millimeters
Min
Max
--5.33
0.89
1.14
2.79
3.30
0.71
0.81
16.26
16.76
10.29
10.80
2.54 TYP
5.08 REF
2.16
2.67
13.39
13.64
5.08
--3.56
3.81
2.73 REF
Inches
Min
Max
--.210
.035
.045
.110
.130
.028
.032
.640
.660
.405
.425
.100 TYP
.200 REF
.085
.105
.527
.537
.200
--.140
.150
.1075 REF
NOTES:
1. Pin 1 is indicated by the ESD marking on the package. Pin numbers are for reference only.
2. The U. S. Government preferred system of measurement is the metric SI. This item was designed using inch-pound
units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the
inch-pound units shall take precedence.
3. Case outline Y weight: 3.2 grams typical.
FIGURE 1. Case outlines - Continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-09213
A
REVISION LEVEL
SHEET
8
Case outline Z.
Symbol
A
A1
A2
øb
D
D1/E
e
e1
L
L1
L2
øP
S1
Millimeters
Min
Max
--5.33
0.89
1.14
2.79
3.30
0.71
0.81
16.26
16.76
10.29
10.80
2.54 TYP
5.08 REF
2.16
2.67
13.39
13.64
5.08
--3.56
3.81
2.73 REF
Inches
Min
Max
--.210
.035
.045
.110
.130
.028
.032
.640
.660
.405
.425
.100 TYP
.200 REF
.085
.105
.527
.537
.200
--.140
.150
.1075 REF
NOTES:
1. Pin 1 is indicated by the ESD marking on the package. Pin numbers are for reference only.
2. The U. S. Government preferred system of measurement is the metric SI. This item was designed using inch-pound
units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the
inch-pound units shall take precedence.
3. Case outline Z weight: 3.2 grams typical.
FIGURE 1. Case outlines - Continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-09213
A
REVISION LEVEL
SHEET
9
Device type
01
Case outlines
U
X, Y, and Z
Terminal number
Terminal symbol
Terminal symbol
1
ADJUST
ADJUST
2
VIN
VOUT
3
VOUT
VIN
NOTE: Case outlines X, Y, and Z: The case / mounting
flange is isolated from the internal circuitry.
FIGURE 2. Terminal connections.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-09213
A
REVISION LEVEL
SHEET
10
FIGURE 3. Radiation exposure circuits.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-09213
A
REVISION LEVEL
SHEET
11
TABLE II. Electrical test requirements.
MIL-PRF-38534 test requirements
Subgroups
(in accordance with
MIL-PRF-38534, group A
test table)
Interim electrical parameters
---
Final electrical parameters
1*, 2, 3
Group A test requirements
1, 2, 3
Group C end-point electrical
parameters
1, 2, 3
1
End-point electrical parameters
for radiation hardness assurance
(RHA) devices
* PDA applies to subgroup 1.
4.2 Screening. Screening shall be in accordance with MIL-PRF-38534. The following additional criteria shall apply:
a.
b.
Burn-in test, method 1015 of MIL-STD-883.
(1)
Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level
control and shall be made available to either DLA Land and Maritime-VA or the acquiring activity upon request.
Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance
with the intent specified in method 1015 of MIL-STD-883.
(2)
TC = +125C minimum.
Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter
tests prior to burn-in are optional at the discretion of the manufacturer.
4.3 Conformance and periodic inspections. Conformance inspection (CI) and periodic inspection (PI) shall be in accordance
with MIL-PRF-38534 and as specified herein.
4.3.1 Group A inspection (CI). Group A inspection shall be in accordance with MIL-PRF-38534 and as follows:
a.
Tests shall be as specified in table II herein.
b.
Subgroups 4, 5, 6, 7, 8, 9, 10, and 11 shall be omitted.
4.3.2 Group B inspection (PI). Group B inspection shall be in accordance with MIL-PRF-38534.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-09213
A
REVISION LEVEL
SHEET
12
4.3.3 Group C inspection (PI). Group C inspection shall be in accordance with MIL-PRF-38534 and as follows:
a.
End-point electrical parameters shall be as specified in table II herein.
b.
Steady-state life test, method 1005 of MIL-STD-883.
(1)
Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level
control and shall be made available to either DLA Land and Maritime-VA or the acquiring activity upon request.
Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance
with the intent specified in method 1005 of MIL-STD-883.
(2)
TC = +125C minimum.
(3)
Test duration: 1,000 hours minimum as specified in 1005 of MIL-STD-883.
4.3.4 Group D inspection (PI). Group D inspection shall be in accordance with MIL-PRF-38534.
4.3.5 Radiation Hardness Assurance (RHA) inspection. RHA qualification is required for those devices with the RHA
designator as specified herein. End-point electrical parameters for RHA devices shall be specified in table II. Radiation
testing will be in accordance with the qualifying activity (DLA Land and Maritime-VQ) approved plan and with MIL-PRF-38534,
Appendix G.
4.3.5.1 Total dose irradiation testing. Total dose irradiation testing shall be in accordance with MIL-STD-883 method 1019,
condition A and as specified herein. Testing shall be performed at initial qualification and after any design or process changes
which may affect the RHA response of the device type. The initial wafer of the radiation hardened active element shall be tested
in the hybrid circuit with a minimum of 8 devices tested (4 devices under bias and 4 devices not under bias) in accordance with
MIL-STD-883 method 1019, condition A.
5. PACKAGING
5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38534.
6. NOTES
6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications
(original equipment), design applications, and logistics purposes.
6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractorprepared specification or drawing.
6.3 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated as specified in MIL-PRF38534.
6.4 Record of users. Military and industrial users shall inform DLA Land and Maritime when a system application requires
configuration control and the applicable SMD. DLA Land and Maritime-VA will maintain a record of users and this list will be
used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronic devices (FSC
5962) should contact DLA Land and Maritime-VA, telephone (614) 692-0547.
6.5 Comments. Comments on this drawing should be directed to DLA Land and Maritime-VA, Columbus, Ohio 43218-3990,
or telephone (614) 692-1081.
6.6 Sources of supply. Sources of supply are listed in MIL-HDBK-103 and QML-38534. The vendors listed in MIL-HDBK-103
and QML-38534 have submitted a certificate of compliance (see 3.7 herein) to DLA Land and Maritime-VA and have agreed to
this drawing.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-09213
A
REVISION LEVEL
SHEET
13
STANDARD MICROCIRCUIT DRAWING BULLETIN
DATE: 11-01-10
Approved sources of supply for SMD 5962-09213 are listed below for immediate acquisition information only and shall
be added to MIL-HDBK-103 and QML-38534 during the next revisions. MIL-HDBK-103 and QML-38534 will be
revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a
certificate of compliance has been submitted to and accepted by DLA Land and Maritime-VA. This information
bulletin is superseded by the next dated revisions of MIL-HDBK-103 and QML-38534. DLA Land and Maritime
maintains an online database of all current sources of supply at http://www.dscc.dla.mil/Programs/Smcr/.
Standard
microcircuit drawing
PIN 1/
Vendor
CAGE
number
Vendor
similar
PIN 2/
5962R0921301HUA
5962R0921301HUC
5962R0921301HXA
5962R0921301HXC
5962R0921301HYA
5962R0921301HYC
5962R0921301HZA
5962R0921301HZC
51651
51651
51651
51651
51651
51651
51651
51651
MSK 5972HRHL
MSK 5972HRHL
MSK 5972HRHS
MSK 5972HRHS
MSK 5972HRHU
MSK 5972HRHU
MSK 5972HRHD
MSK 5972HRHD
5962R0921301KUA
5962R0921301KUC
5962R0921301KXA
5962R0921301KXC
5962R0921301KYA
5962R0921301KYC
5962R0921301KZA
5962R0921301KZC
51651
51651
51651
51651
51651
51651
51651
51651
MSK 5972KRHL
MSK 5972KRHL
MSK 5972KRHS
MSK 5972KRHS
MSK 5972KRHU
MSK 5972KRHU
MSK 5972KRHD
MSK 5972KRHD
1/
2/
The lead finish shown for each PIN representing a hermetic
package is the most readily available from the manufacturer
listed for that part. If the desired lead finish is not listed
contact the Vendor to determine its availability.
Caution. Do not use this number for item acquisition. Items
acquired to this number may not satisfy the performance
requirements of this drawing.
Vendor CAGE
number
51651
Vendor name
and address
M. S. Kennedy Corporation
4707 Dey Road
Liverpool, NY 13088
The information contained herein is disseminated for convenience only and the
Government assumes no liability whatsoever for any inaccuracies in the
information bulletin.