1W DC-DC Converter P1R-Series ● ● ● ● ● 14 Pin DIL Linear regulated output voltage Low ripple and noise Up to 3000 VDC isolation MTBF >3.5 MHours Model selection guide Typ Input nominal voltage range [VDC] P1R3R33R3D 2.97…3.63 P1R3R305D 2.97…3.63 P1R3R37R2D 2.97…3.63 P1R3R309D 2.97…3.63 P1R3R312D 2.97…3.63 P1R3R315D 2.97…3.63 P1R053R3D 4.5...5.5 P1R0505D 4.5...5.5 P1R057R2D 4.5...5.5 P1R0509D 4.5...5.5 P1R0512D 4.5...5.5 P1R0515D 4.5...5.5 P1R123R3D 10.8...13.2 P1R1205D 10.8...13.2 P1R127R2D 10.8...13.2 P1R1209D 10.8...13.2 P1R1212D 10.8...13.2 P1R1215D 10.8...13.2 P1R243R3D 21.6...26.4 P1R2405D 21.6...26.4 P1R247R2D 21.6...26.4 P1R2409D 21.6...26.4 P1R2412D 21.6...26.4 P1R2415D 21.6...26.4 Suffix: “H” for 3kV isolation Specifications Input Voltage range Filter Reflected input ripple current Isolation: Rated voltage I-O isolation resistance Capacitance Output Voltage accuracy Ripple and noise (at 20 MHz BW) Line voltage regulation Load voltage regulation Temperature coefficient EMC Radiated emissions Conducted emissions ESD RS EFT Surge CS PFM Input current no load full load Output voltage Output current Efficiency typ. Capacitive Load [mA] [mA] [VDC] [mA] [%] [µF] 40 40 40 45 45 45 30 35 45 40 35 35 20 20 20 20 20 20 10 10 10 10 10 10 520 505 505 505 505 466 350 317 327 298 298 298 146 132 132 128 122 126 73 76 76 61 63 63 3.3 5.0 7.2 9.0 12.0 15.0 3.3 5.0 7.2 9.0 12.0 15.0 3.3 5.0 7.2 9.0 12.0 15.0 3.3 5.0 7.2 9.0 12.0 15.0 333 200 139 111 84 67 333 200 139 111 84 67 333 200 139 111 84 67 333 200 139 111 84 67 58 60 60 60 60 65 57 65 65 65 68 68 57 63 65 65 68 66 60 65 65 68 68 68 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 ± 10%, max. Capacitors 20 mA p-p 1000 VDC, standard 3000 VDC suffix “H” 109 Ω 60 pF, typ. ± 2 %, max. 50 mVp-p, max. ± 0.5 % ± 0.5 % ± 1 % @ 3.3 V output type ± 0.02 % / °C EN 55022 Class B EN 55022 Class B IEC 61000-4-2 perf. criteria A IEC 61000-4-3 perf. criteria A IEC 61000-4-4 perf. criteria A IEC 61000-4-5 perf. criteria A IEC 61000-4-6 perf. criteria A IEC 61000-4-6 perf. criteria A General Switching frequency Reliability calculated MTBF (MIL-HDBK-217F) Safety standard Environmental Operating temperatur (ambient) Case temperature Storage temperature Derating Humidity Cooling Physical Dimensions Weight Case material Potting material Pin material Absolute maximum ratings Vin 3.3 V types Vin 5V types Vin 12V types Vin 24V types Pin soldering temperature 1.5 mm distance from body 50 kHz, typ. >3,5 Mhrs IEC 60950-1 -40 … +85 °C 100 °C, max. -40 °C to +125 °C None required Up to 95 % rel., non-condensing Free-air convection 20.3 x 10.2 x 6.9 mm 2.7 g non-conductive black plastic (UL94V-0 rated) Epoxy (UL94V-0 rated) 0.5 mm alloy 42 solder coated 0…5 V max. 100 ms 0…7 V max. 100 ms 0…15 V max. 100 ms 0…28 V max. 100 ms 260 °C for 10s Page 1 of 3 Deutschland: Inselkammerstraße 10 D-82008 Unterhaching Tel.: 089 614 503-10 E-Mail: [email protected] Schweiz: Gründenstraße 82 CH-8247 Flurlingen Tel.: 052 647 42 00 E-Mail: [email protected] 1W DC-DC Converter P1R-Series Efficiency vs output current EMI Filter L: 12µH Input filter components (C and L ) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module and all leads should be minimized to decrease radiated noise. 1. 2. 3. 4. 5. 6. 7. DC Load C: 470µF DC Ripple & Noise measured with 20 MHz bandwidth. Tested by minimal input voltage and constant resistive load. Measured Input reflected ripple current with a simulated source inductance of 12 µH. Input filter components are be required to help meet conducted emission class B, which application refer to the EMI Filter of design and feature configuration. An external filter capacitor is required if the module has to meet IEC61000-4-4 and IEC61000-4-5. Suggested filter capacitor: Nippon – Chemicon’s KY series, 470uF / 100V. Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. Operation under no-load conditions will not damage these devices, however they may not meet all listed specifications. Page 2 of 3 Deutschland: Inselkammerstraße 10 D-82008 Unterhaching Tel.: 089 614 503-10 E-Mail: [email protected] Schweiz: Gründenstraße 82 CH-8247 Flurlingen Tel.: 052 647 42 00 E-Mail: [email protected] 1W DC-DC Converter P1R-Series Dimensions 20.32 PHI-CON P1R0505D 10.16 6.85 3.0 15.24 0.25 1 All dimensions in mm 1. Pin wide tolerance ± 0.05 mm 2. Pin length and pitch tolerance ± 0.35 mm 3. Package tolerance ± 0.5 mm 7 Bottom view 7.62 11 14 7.62 10 9 8 0.5 2.54 Pin connections Pin 1 7 8 9 10 11 14 Standard -V Input N.C. No pin +V Output No pin -V Output +V Input 3 kVDC Isolation -V Input N.C. +V Output No pin -V Output No pin +V Input Only for professional use by professionals! Not for resale or distribution to the general public in any way! Read the instructions for use carefully before using! Life Support Policy: HY-LINE does not authorize the use of any of its products for use in life support devices or systems without the express written approval of an officer of the Company. Life support systems are devices which support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in significant injury to the user. Rev: 11.12 f Page 3 of 3 Deutschland: Inselkammerstraße 10 D-82008 Unterhaching Tel.: 089 614 503-10 E-Mail: [email protected] Schweiz: Gründenstraße 82 CH-8247 Flurlingen Tel.: 052 647 42 00 E-Mail: [email protected]