AD8574-DSCC: Military Data Sheet

REVISIONS
LTR
DESCRIPTION
DATE
Prepared in accordance with ASME Y14.24
APPROVED
Vendor item drawing
REV
PAGE
REV
PAGE
REV STATUS
OF PAGES
REV
PAGE
1
2
PMIC N/A
PREPARED BY
RICK OFFICER
Original date of drawing
YY-MM-DD
CHECKED BY
RAJESH PITHADIA
12-09-05
4
A
REV
5
6
7
8
9
10
11
12
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
http://www.landandmaritime.dla.mil/
TITLE
MICROCIRCUIT, LINEAR, SINGLE SUPPLY,
QUAD, OPERATIONAL AMPLIFIER, MONOLITHIC
SILICON
APPROVED BY
CHARLES F. SAFFLE
SIZE
AMSC N/A
3
CODE IDENT. NO.
DWG NO.
V62/12634
16236
PAGE
1
OF
12
5962-V094-12
1. SCOPE
1.1 Scope. This drawing documents the general requirements of a high performance single supply quad operational amplifier
microcircuit, with an operating temperature range of -55°C to +125°C.
1.2 Vendor Item Drawing Administrative Control Number. The manufacturer’s PIN is the item of identification. The vendor item
drawing establishes an administrative control number for identifying the item on the engineering documentation:
V62/12634
-
Drawing
number
01
X
E
Device type
(See 1.2.1)
Case outline
(See 1.2.2)
Lead finish
(See 1.2.3)
1.2.1 Device type(s).
Device type
Generic
Circuit function
01
AD8574
Zero drift, single supply, quad operational amplifier
1.2.2 Case outline(s). The case outline(s) are as specified herein.
Outline letter
Number of pins
X
14
JEDEC PUB 95
Package style
MO-153-AB-1
Plastic thin shrink small outline
1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as provided by the device manufacturer:
Finish designator
A
B
C
D
E
Z
DLA LAND AND MARITIME
COLUMBUS, OHIO
Material
Hot solder dip
Tin-lead plate
Gold plate
Palladium
Gold flash palladium
Other
SIZE
A
CODE IDENT NO.
16236
REV
DWG NO.
V62/12634
PAGE
2
1.3 Absolute maximum ratings.
1/
Supply voltage range (VS) .......................................................................................... 6 V
Input voltage ...............................................................................................................
Differential input voltage .............................................................................................
Power dissipation (PD) ...............................................................................................
Output short circuit duration to GND ..........................................................................
Storage temperature range (TSTG) ............................................................................
GND to VS + 0.3 V
±5.0 V 2/
138.8 mW typical
Indefinite
-65°C to +150°C
Junction temperature range (TJ) ................................................................................ -65°C to +150°C
Lead temperature (soldering, 60 seconds) ................................................................. +300°C
Thermal resistance, junction to case (θJC) ................................................................. 36°C/W
Thermal resistance, junction to ambient (θJA) ............................................................ 180°C/W
Electrostatic discharge:
Human body model (HBM) ..................................................................................... 2000 V
1.4 Recommended operating conditions. 3/
Supply voltage range (VS) .......................................................................................... 5 V
Operating free-air temperature range (TA) .................................................................. -55°C to +125°C
1/
2/
3/
Stresses beyond those listed under “absolute maximum rating” may cause permanent damage to the device. These are stress
ratings only, and functional operation of the device at these or any other conditions beyond those indicated under
“recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may
affect device reliability.
Differential input voltage is limited to ±5.0 V or the supply voltage, whichever is less.
Use of this product beyond the manufacturers design rules or stated parameters is done at the user’s risk. The manufacturer
and/or distributor maintain no responsibility or liability for product used beyond the stated limits.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
DWG NO.
V62/12634
PAGE
3
2. APPLICABLE DOCUMENTS
JEDEC PUB 95
–
Registered and Standard Outlines for Semiconductor Devices
(Applications for copies should be addressed to the Electronic Industries Alliance, 2500 Wilson Boulevard, Arlington, VA
22201-3834 or online at http://www.jedec.org)
3. REQUIREMENTS
3.1 Marking. Parts shall be permanently and legibly marked with the manufacturer’s part number as shown in 6.3 herein and as
follows:
A.
B.
C.
Manufacturer’s name, CAGE code, or logo
Pin 1 identifier
ESDS identification (optional)
3.2 Unit container. The unit container shall be marked with the manufacturer’s part number and with items A and C (if applicable)
above.
3.3 Electrical characteristics. The maximum and recommended operating conditions and electrical performance characteristics are
as specified in 1.3, 1.4, and table I herein.
3.4 Design, construction, and physical dimension. The design, construction, and physical dimensions are as specified herein.
3.5 Diagrams.
3.5.1 Case outline. The case outline shall be as shown in 1.2.2 and figure 1.
3.5.2 Terminal connections. The terminal connections shall be as shown in figure 2.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
DWG NO.
V62/12634
PAGE
4
TABLE I. Electrical performance characteristics. 1/
Test
Symbol
Conditions
VS = 5 V, VCM = 2.5 , VO = 2.5 V
unless otherwise specified
Temperature,
TA
Device
type
Limits
Min
Unit
Max
Input characteristics.
Offset voltage
+25°C
VOS
01
15
-55°C to +125°C
Input bias current
+25°C
IB
01
-55°C to +125°C
Input offset current
+25°C
IOS
01
VIN
Common mode
rejection ratio
CMRR
VCM = 0 V to 5 V
+25°C
01
0
+25°C
01
120
AVO
+25°C
VO = 0.3 V to 4.7 V, RL = 10 kΩ
01
∆VOS /
∆T
1.5
nA
70
pA
5
V
dB
125
dB
120
-55°C to +125°C
Offset voltage drift
pA
115
-55°C to +125°C
Large signal voltage 2/
gain
50
200
-55°C to +125°C
Input voltage range
µV
5
-55°C to +125°C
01
+25°C
01
0.04
µV/°C
Output characteristics.
Output voltage high
VOH
RL = 100 kΩ to GND
RL = 10 kΩ to GND
Output voltage low
VOL
-55°C to +125°C
4.99
+25°C
4.95
-55°C to +125°C
4.95
+25°C
RL = 100 kΩ to +VS
RL = 10 kΩ to +VS
4.99
01
V
10
-55°C to +125°C
10
+25°C
30
-55°C to +125°C
30
mV
See footnotes at end of table.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
DWG NO.
V62/12634
PAGE
5
TABLE I. Electrical performance characteristics – Continued. 1/
Test
Symbol
Conditions
VS = 5 V, VCM = 2.5 , VO = 2.5 V
unless otherwise specified
Temperature,
TA
Device
type
Limits
Min
Unit
Max
Output characteristics – continued.
Short circuit limit
+25°C
ISC
01
+25°C
IO
mA
±40 typical
-55°C to +125°C
Output current
±25
01
±30 typical
mA
±15 typical
-55°C to +125°C
Power supply.
Power supply rejection
ratio
PSRR
+25°C
VS = 2.7 V to 5.5 V
01
ISY
+25°C
VO = 0 V
dB
115
-55°C to +125°C
Supply current per
amplifier
120
01
µA
975
1075
-55°C to +125°C
Dynamic performance.
Slew rate
SR
RL = 10 kΩ
Overload recovery time
Gain bandwidth
product
GBP
+25°C
01
0.4 typical
+25°C
01
+25°C
01
1.5 typical
MHz
+25°C
01
1.3 typical
µVpp
V/µs
0.3
ms
Noise performance.
Voltage noise
enp-p
0 Hz to 10 Hz
0 Hz to 1 Hz
Voltage noise density
en
0.41 typical
f = 1 kHz
+25°C
01
51 typical
nV /
Hz
Current noise density
in
f = 10 Hz
+25°C
01
2 typical
fA /
Hz
See footnotes at end of table.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
DWG NO.
V62/12634
PAGE
6
TABLE I. Electrical performance characteristics – Continued. 1/
Test
Symbol
Conditions
VS = 2.7 V, VCM = 1.35 V,
Temperature,
TA
Device
type
Limits
Min
VO = 1.35 V
unless otherwise specified
Unit
Max
Input characteristics.
Offset voltage
+25°C
VOS
01
15
-55°C to +125°C
Input bias current
+25°C
IB
01
-55°C to +125°C
Input offset current
+25°C
IOS
01
VIN
Common mode
rejection ratio
CMRR
VCM = 0 V to 2.7 V
+25°C
01
0
+25°C
01
115
AVO
+25°C
VO = 0.3 V to 2.4 V, RL = 10 kΩ
01
∆VOS /
∆T
1.5
nA
50
pA
2.7
V
dB
110
dB
105
-55°C to +125°C
Offset voltage drift
pA
110
-55°C to +125°C
Large signal voltage 2/
gain
50
200
-55°C to +125°C
Input voltage range
µV
5
-55°C to +125°C
01
+25°C
01
0.04
µV/°C
Output characteristics.
Output voltage high
VOH
RL = 100 kΩ to GND
RL = 10 kΩ to GND
Output voltage low
VOL
-55°C to +125°C
2.685
+25°C
2.67
-55°C to +125°C
2.67
+25°C
RL = 100 kΩ to +VS
RL = 10 kΩ to +VS
2.685
01
V
10
-55°C to +125°C
10
+25°C
20
-55°C to +125°C
20
mV
See footnotes at end of table.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
DWG NO.
V62/12634
PAGE
7
TABLE I. Electrical performance characteristics – Continued. 1/
Test
Symbol
Conditions
VS = 2.7 V, VCM = 1.35 V,
Temperature,
TA
Device
type
Limits
Min
VO = 1.35 V
unless otherwise specified
Unit
Max
Output characteristics – continued.
Short circuit limit
+25°C
ISC
01
+25°C
IO
mA
±10 typical
-55°C to +125°C
Output current
±10
01
±10 typical
mA
±5 typical
-55°C to +125°C
Power supply.
Power supply rejection
ratio
PSRR
+25°C
VS = 2.7 V to 5.5 V
01
ISY
+25°C
VO = 0 V
dB
115
-55°C to +125°C
Supply current per
amplifier
120
01
µA
900
1000
-55°C to +125°C
Dynamic performance.
Slew rate
SR
RL = 10 kΩ
Overload recovery time
Gain bandwidth
product
GBP
+25°C
01
0.5 typical
V/µs
+25°C
01
0.05 typical
ms
+25°C
01
1.0 typical
MHz
Noise performance.
Voltage noise
enp-p
0 Hz to 10 Hz
+25°C
01
2.0 typical
µVpp
Voltage noise density
en
f = 1 kHz
+25°C
01
94 typical
nV /
Hz
Current noise density
in
f = 10 Hz
+25°C
01
2 typical
fA /
Hz
1/
Testing and other quality control techniques are used to the extent deemed necessary to assure product performance over
the specified temperature range. Product may not necessarily be tested across the full temperature range and all parameters
may not necessarily be tested. In the absence of specific parametric testing, product performance is assured by characterization
and/or design.
2/
Gain testing is dependent upon test bandwidth.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
DWG NO.
V62/12634
PAGE
8
Case X
FIGURE 1. Case outline.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
DWG NO.
V62/12634
PAGE
9
Case X
Dimensions
Inches
Symbol
Millimeters
Min
Max
Min
Max
A
---
.047
---
1.20
A1
.001
.005
0.05
0.15
A2
.031
.041
0.80
1.05
b
.007
.011
0.19
0.30
c
.003
.007
0.09
0.20
D
.192
.200
4.90
5.10
E
.169
.177
4.30
4.50
E1
.251 BSC
6.40 BSC
e
.025 BSC
0.65 BSC
L
.017
.028
0.45
0.75
NOTES:
1. Controlling dimensions are millimeter, inch dimensions are given for reference only.
2. Falls within reference to JEDEC MO-153-AB-1.
FIGURE 1. Case outline - Continued.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
DWG NO.
V62/12634
PAGE
10
Device type
01
Case outline
X
Terminal number
Terminal
symbol
1
OUTPUT A
2
-INPUT A
3
+INPUT A
4
+VS
5
+INPUT B
6
-INPUT B
7
OUTPUT B
8
OUTPUT C
9
-INPUT C
10
+INPUT C
11
-VS
12
+INPUT D
13
-INPUT D
14
OUTPUT D
FIGURE 2. Terminal connections.
DLA LAND AND MARITIME
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
DWG NO.
V62/12634
PAGE
11
4. VERIFICATION
4.1 Product assurance requirements. The manufacturer is responsible for performing all inspection and test requirements as
indicated in their internal documentation. Such procedures should include proper handling of electrostatic sensitive devices,
classification, packaging, and labeling of moisture sensitive devices, as applicable.
5. PREPARATION FOR DELIVERY
5.1 Packaging. Preservation, packaging, labeling, and marking shall be in accordance with the manufacturer’s standard commercial
practices for electrostatic discharge sensitive devices.
6. NOTES
6.1 ESDS. Devices are electrostatic discharge sensitive and are classified as ESDS class 1 minimum.
6.2 Configuration control. The data contained herein is based on the salient characteristics of the device manufacturer’s data book.
The device manufacturer reserves the right to make changes without notice. This drawing will be modified as changes are provided.
6.3 Suggested source(s) of supply. Identification of the suggested source(s) of supply herein is not to be construed as a guarantee
of present or continued availability as a source of supply for the item. DLA Land and Maritime maintains an online database of all
current sources of supply at http://www.landandmaritime.dla.mil/Programs/Smcr/.
Vendor item drawing
administrative control
number 1/
Device
manufacturer
CAGE code
Transport
media,
quantity
Vendor part number
V62/12634-01XE
24355
Reel, 2500
AD8574TRU-EP-RL
Tube, 96
AD8574TRU-EP
1/ The vendor item drawing establishes an administrative control number for identifying the
item on the engineering documentation.
CAGE code
24355
DLA LAND AND MARITIME
COLUMBUS, OHIO
Source of supply
Analog Devices
Route 1 Industrial Park
P.O. Box 9106
Norwood, MA 02062
Point of contact: Raheen Business Park
Limerick, Ireland
SIZE
A
CODE IDENT NO.
16236
REV
DWG NO.
V62/12634
PAGE
12