INTEGRATED CIRCUITS DATA SHEET TDA8417 TV and VTR stereo/dual sound processor with integrated filters and I2C-bus control Preliminary specification File under Integrated Circuits, IC02 September 1989 Philips Semiconductors Preliminary specification TV and VTR stereo/dual sound processor with integrated filters and I2C-bus control TDA8417 GENERAL DESCRIPTION The TDA8417 is a processor of stereo/dual language signals (B/G-standard) for stereo sound television receivers and VTRs, using the switched-capacitor technique. The AF signals at the TDA8417 inputs must be “(L+R)/2” or “language A” on one channel and “R” or “language B” on the second channel (where L = left and R = right). The carrier frequency of the second channel is also modulated by an identification signal (stereo or dual sound). The device is controlled by a microcomputer via the two-line, bidirectional I2C-bus. Features • Use of the switched-capacitor technique for signal processing • Small amount of peripheral components • Integrated anti-aliasing filters • Low distortion AF signal handling • Integrated de-emphasis with a time constant of 50 µs • Two general purpose output ports • Full ESD protection QUICK REFERENCE DATA PARAMETER CONDITION SYMBOL MIN. TYP. MAX. UNIT Supply voltage (pin 15) VP − 12 − V Supply current (pin 15) IP − 10 − mA Vo − 2 − V (S+W)/W 70 − − dB AF output signal (RMS value) (pins 11 to 14) Weighted signal-to-noise ratio of the AF output signals (CCIR 468/3) Crosstalk attenuation stereo mode at f = 1 kHz αS 40 − − dB dual sound mode at f = 40 Hz to 12.5 kHz αDS 70 − − dB Pilot signal input sensitivity Vi − 2.5 − mV Total harmonic distortion THD − 0.1 − % PACKAGE OUTLINE 20-lead DIL; plastic (SOT146); SOT146-1; 1996 November 18 September 1989 2 Philips Semiconductors Preliminary specification TDA8417 Fig.1 Block diagram. TV and VTR stereo/dual sound processor with integrated filters and I2C-bus control September 1989 3 Philips Semiconductors Preliminary specification TV and VTR stereo/dual sound processor with integrated filters and I2C-bus control Fig.2 Input and output loading diagram. September 1989 4 TDA8417 Philips Semiconductors Preliminary specification TV and VTR stereo/dual sound processor with integrated filters and I2C-bus control TDA8417 PINNING 1 Control port C1 2 SDA, serial data line (I2C-bus) 3 SCL, serial clock line (I2C-bus) 4 Oscillator input (or quartz) 5 Digital ground (0 V) 6 Not connected, but reserved 7 Sound channel input AF2 (E2) 8 Sound channel input AF1 (E1) 9 External AF input (E4) 10 Not connected, but reserved 11 Output A4 AF 2 output 12 Output A3 AF 2 output 13 Output A2 AF 1 output 14 Output A1 AF 1 output 15 Supply voltage VP 16 Analogue ground (0 V) 17 Ripple rejection improvement 18 Mute input 19 Control port C2 20 Not connected, but reserved FUNCTIONAL DESCRIPTION Anti-aliasing filters Frequency band limitation is performed by a second order Sallen and Key low-pass filter inserted in the AF signal path and the identification circuit. This limitation is necessary because of the time-discrete signal processing needed to meet the Nyquist criterium. Identification To enable the identification of the transmitted AF signal (mono, stereo or dual sound), the carrier frequency of the second channel (E2) is also modulated by an identification signal. The identification signal is a 54.6875 kHz pilot carrier signal which is 50% amplitude modulated by either a 117.4 Hz signal for stereo transmission or by a 274.1 Hz signal for dual sound transmission. The identification section of the circuit consists of a 54 kHz high-pass filter followed by a gain controlled amplifier with an AM demodulator. The total gain of the high-pass filter and the amplifier is approximately 56 dB. The demodulated identification signal is filtered by the identification band-pass filters, (117.4 Hz for stereo transmission, 274.1 Hz for dual sound transmission). The output from either filter is converted to a DC signal by a peak detector and the necessary hysteresis is performed by a Schmitt-trigger. The resultant DC output signals indicate the status of the transmitter (mono, stereo or dual sound). September 1989 5 Philips Semiconductors Preliminary specification TV and VTR stereo/dual sound processor with integrated filters and I2C-bus control TDA8417 De-matrix and de-emphasis Depending on the results of the identification circuit (mono, stereo or dual sound) the AF signals at the inputs E1 and E2 are converted to the signals at E1* and E2* as listed in Table 1. Table 1 Transmitter status (1) TRANSMITTER STATUS E1 E2 E1* E2* mono 0.7(L+R) − 2(L+R) − stereo 0.7(L+R) 2R 4L 4R dual sound 0.7A B 2A 2B Note 1. L = left channel signal; R = right channel signal; A = first sound channel signal; B = second sound channel signal This section of the circuit also performs the de-emphasis (50 µs time constant) with a high degree of accuracy. AF switch The AF switch is used to switch to either the internal sound sources (E1* or E1* and E2*) or, to the external sound source (E3 and E4) and is controlled via the I2C-bus. Source selector The source selector is used to connect the outputs from the AF switch to the outputs A1 to A4 as illustrated by Table 5. The selector is controlled via the I2C-bus. Muting In this mode the AF outputs A1 to A4 are muted, and the identification circuit is deactivated (mono). The muting is active after power-on reset or as a result of user control (via the mute input and bit CR3 of the control byte of the mute and port control register; see Table 4). Sound mute If the switch register is set to (00) hex, (sound mute) only the AF outputs are muted, the identification circuit is still active and can be read (status register) via the I2C-bus. September 1989 6 Philips Semiconductors Preliminary specification TV and VTR stereo/dual sound processor with integrated filters and I2C-bus control TDA8417 Power-on reset The following actions are carried out by the internal power-on reset when it is active: • The AF outputs are muted • The identification circuit is deactivated (mono) • The control ports (C1 and C2) are set LOW • The I2C-bus transceiver is initialized When the power-on reset becomes passive the following occurs: • The AF outputs are kept in the mute state until the contents of the switch register are changed from (00) hex via the I2C-bus • The identification circuit is activated • The control ports are LOW until the mute and control port register is changed (CR bits 10, 11, 20 and 21) • The I2C-bus transceiver is activated September 1989 7 Philips Semiconductors Preliminary specification TV and VTR stereo/dual sound processor with integrated filters and I2C-bus control Fig.3 Mute modes. September 1989 8 TDA8417 Philips Semiconductors Preliminary specification TV and VTR stereo/dual sound processor with integrated filters and I2C-bus control TDA8417 Control ports The general purpose control ports C1 and C2 can be set to LOW, HIGH or high impedance via the I2C-bus. I2C-bus receiver and data handling Bus specification The TDA8417 is controlled, via the bidirectional 2-line I2C-bus, by a microcomputer. The two lines are a serial data line (SDA) and a serial clock line (SCL). Both lines must be connected to a positive supply via a pull-up resistor. Data transfer may be initiated only when the bus is not busy. When the bus is free both lines are HIGH. The data on the SDA line must be stable during the HIGH period of the clock. The HIGH or LOW state of the data line can only change when the clock signal on the SCL line is LOW. The set up and hold times are specified in the CHARACTERISTICS. A HIGH-to-LOW transition of the SDA line while SCL is HIGH is defined as the start condition (S). A LOW-to-HIGH transition of the SDA line while SCL is HIGH is defined as the stop condition (P). The bus receiver will be reset on the reception of a start condition. The bus is considered to be busy after the start condition. The bus is considered to be free again after a stop condition. The I2C-BUS PROTOCOL OF THE TDA8417 The TDA8417 is controlled by a microcomputer and can be written to or read from via the I2C-bus. The first byte is the address and determines whether the TDA8417 is to be read from (status register) or written to (switch register or mute and port control register). Read from (TDA8417 is a slave transmitter) Write to (TDA8417 is a slave receiver) Where: S = start bit A = acknowledge bit Fig.4 Address byte. September 1989 9 Philips Semiconductors Preliminary specification TV and VTR stereo/dual sound processor with integrated filters and I2C-bus control TDA8417 Reading the TDA8417 Reading the TDA8417 means reading the status register and the data stream will have the format as illustrated in Fig.5 below. Where: S = start bit A = acknowledge bit P = stop bit Fig.5 Read format. The second byte, the contents of the status register, is defined by Table 2. Table 2 Status register D7 D6 D5 D4 D3 D2 D1 D0 PONRES ST DS 0 0 0 0 0 Where: PONRES = power on reset 1 = power on reset active after switching on or power breakdown 0 = after reading the status register ST = stereo transmission DS = dual sound transmission The truth table for the ST and DS bits is provided by Table 3. Table 3 Truth table for ST and DS bits ST DS 0 0 mono transmission 0 1 dual sound transmission 1 0 stereo transmission September 1989 DEFINITION 10 Philips Semiconductors Preliminary specification TV and VTR stereo/dual sound processor with integrated filters and I2C-bus control TDA8417 Writing to the TDA8417 Writing to the TDA8417 means, writing to either the switch register or the mute and port control register. Which one is to be addressed is defined by the subaddress (the second byte) as illustrated by Fig.6 below. The third byte contains the information to be stored in the specified register. Where: S = start bit A = acknowledge bit P = stop bit Fig.6 Write format. Table 4 defines the contents of the mute and port control register. Table 4 Mute and port control register (1) D7 D6 D5 X X X X X D4 CR3 D3 CR21 D2 CR20 D1 CR11 D0 CR10 DEFINITION X 0 0 control port C1 = LOW X 0 1 control port C1 = HIGH X X 1 X control port C1 = high impedance X X X 0 0 control port C2 = LOW X X X 0 1 control port C2 = HIGH X X X 1 X control port C2 = high impedance X X X 0 mute is active when pin 18 is LOW (default) X X X 1 mute is active when pin 18 is HIGH Note 1. X = don’t care September 1989 11 Philips Semiconductors Preliminary specification TV and VTR stereo/dual sound processor with integrated filters and I2C-bus control TDA8417 Table 5 defines the contents of the switch register. Table 5 Switch register INPUT SWITCH REGISTER OUTPUT E1 E2 E4 A1 D7 D6 D5 D4 D3 D2 D1 D0 (HEX) A2 A3 A4 sound mute − − − − no signal mono M M M − M M M M 0 0 0 0 0 0 0 0 (00) 0 0 0 1 0 0 0 0 (10) St L* R − L* L* L* L* 0 0 0 1 0 0 0 0 (10) stereo St L* R − L R L R 0 0 1 0 1 0 1 0 (2A) sound A DS A B − A A A A 0 0 0 1 0 0 0 0 (10) sound B DS A B − B B B B 0 0 0 1 1 1 1 1 (1F) dual sound DS A B − A A B B 0 0 0 1 1 1 0 0 (1C) DS A B − B B A A 0 0 0 1 0 0 1 1 (13) dual sound DS A B − A B A A 0 0 0 1 0 0 1 0 (12) mix DS A B − A A A B 0 0 0 1 1 0 0 0 (18) DS A B − A B A B 0 0 0 1 1 0 1 0 (1A) DS A B − B B A B 0 0 0 1 1 0 1 1 (1B) DS A B − A B B B 0 0 0 1 1 1 1 0 (1E) − − E4 E4 E4 E4 E4 0 1 1 1 1 1 1 1 (7F) external − Where: M = mono St = stereo DS = dual sound R = right L = left L* = (L + R)/2 A = sound A B = sound B September 1989 12 Philips Semiconductors Preliminary specification TV and VTR stereo/dual sound processor with integrated filters and I2C-bus control TDA8417 RATINGS Limiting values in accordance with Absolute Maximum System (IEC 134) PARAMETER Supply voltage(1) SYMBOL MIN. TYP. MAX. UNIT VP = V15-16 − − 13.2 V IO − − 10 mA Output current pins 11, 12, 13, 14 IO − − 7 mA −IO − − 3 mA Input voltage (not pin 18) VI 0 − VP V Input voltage pin 18 VI = V18-16 − − 7 V Output voltage VO 0 − VP V Total power dissipation Ptot − − 1 W ESD protection (each pin) (0 Ω/200 pF) Ves 500 − − V Operating ambient temperature range Tamb 0 − + 70 °C Storage temperature range Tstg −40 − +150 °C pins 1 and 19 (sink) (source) Note 1. Supply voltage may be applied only when both pins 5 and 15 are connected to ground. September 1989 13 Philips Semiconductors Preliminary specification TV and VTR stereo/dual sound processor with integrated filters and I2C-bus control TDA8417 CHARACTERISTICS VP = 12 V; Tamb = 25 °C. Measurement conditions (see Fig.7): reference level is 1 V (RMS); test frequency = 3.183 kHz; noise measurement in accordance with DIN 45405, CCIR 468-3; oscillator frequency = 10 MHz; pre-emphasis time constant = 50 µs. PARAMETER CONDITIONS SYMBOL MIN. TYP. MAX. UNIT Supplies Supply voltage VP = V15-16 10.8 12 13.2 V Supply current IP = I15 − 10 − mA pins 7 - 14 and 17 Vn-16 − 3.25 − V pin 4 V4-5 − 2 − V fCLK 0.7 − 100 kHz Input voltage LOW VIL −0.3 − 1.5 V Input voltage HIGH VIH 3 − 5 V Timing LOW period tLOW 4.7 − − µs Timing HIGH period tHIGH 4 − − µs Rise time tr − − 1 µs Fall time tf − − 0.3 µs Input current LOW −IIL − − 10 µA Input current HIGH IIH − − 10 µA Input voltage LOW VIL −0.3 − 1.5 V Input voltage HIGH VIH 3 − 5 V Rise time tr − − 1 µs Fall time tf − − 0.3 µs DC levels Bus transceiver Clock frequency (I2 C-bus) note 1 Clock SCL (pin 3) Data SDA (pin 2) Data set-up time tSU; DAT 0.25 − − µs Input current LOW −IIL − − 10 µA Input current HIGH IIH − − 10 µA Output current LOW IOL 3 − − mA Mute port (pin 18) Input voltage LOW note 2 VIL −0.3 − 1.5 V Input voltage HIGH note 2 VIH 3 − 5 V September 1989 14 Philips Semiconductors Preliminary specification TV and VTR stereo/dual sound processor with integrated filters and I2C-bus control PARAMETER CONDITIONS TDA8417 SYMBOL MIN. TYP. MAX. UNIT Control ports (pins 1 and 19) Output voltage LOW note 3 VOL − − 0.5 V Output voltage HIGH note 3 VOH 4.5 − 5 V Output impedance 3-state Zo 1 − − MΩ Output current LOW IOL 1 − − mA Output current HIGH −IOH 1 − − mA (pins 7 to 9) Zi 150 200 − kΩ Input voltage E1 VI − − 0.7 V Input voltage E2 VI − − 1 V AF stages and identification (pins 7 to 14) Input impedance Input voltage E2 for identification active (RMS value) note 4 Vi 2.5 − − mV Voltage gain 7-15/output note 5 Gv 5.9 6 6.1 dB Voltage gain 8-15/output note 5 Gv 8.9 9 9.1 dB Gv −0.1 0 0.1 dB dual mode αds 70 75 − dB stereo mode αs 30 50 − dB Zo 400 500 600 Ω 49.5 50 50.5 µs Voltage gain 9-15/output Crosstalk attenuation notes 6 to 8 Output impedance (pins 11 to 14) De-emphasis time constant note 9 Frequency response note 6 ∆f −1 − 1 dB note 10 THD − − 0.2 % CL − − 1.5 nF THD ≤ 0.2% Vo − − 2 V note 11 RR 50 66 − dB NR − − −80 dB (S+W)/W 70 − − dBV CCIR Total harmonic distortion Capacitive load (pins 11 to 14) Output signal (RMS value) (pins 11 to 14) Ripple rejection Noise from I2 C-bus Signal-to-noise ratio September 1989 15 Philips Semiconductors Preliminary specification TV and VTR stereo/dual sound processor with integrated filters and I2C-bus control PARAMETER CONDITIONS TDA8417 SYMBOL MIN. TYP. MAX. UNIT Signal suppression during mute note 6 SS 70 75 − dB − − 30 mV − 10 − MHz Change of output DC voltage level between any two modes Oscillator Oscillator frequency fOSC External oscillator V4-5 1.7 − − V Quartz series resistor R1 − − 100 Ω Impedance Zi − −1.2 + j9.3 − kΩ Capacitance COSC − 1.7 − pF signal (RMS value) Notes to the characteristics 1. Full specification of I2 C-bus will be supplied on request. 2. Programmable mute state. If the CR3 bit of the mute and port control register is LOW, the mute is active LOW; if it is HIGH, the mute input is active HIGH. 3. Output current IO ≈ 1 mA. 4. Unmodulated. 5. f = 400 Hz; RL = 1 MΩ. 6. 40 Hz ≤ f ≤ 15 kHz. 7. In dual mode: A(B)-signal into B(A)-channel. In stereo mode: R-signal into left, L-signal = 0, reference is 1 V RMS. 8. Source impedance ZS < 1 kΩ. 9. Equivalent to an output level of −3 dB at f = 3.183 kHz. 10. Vo = 1 V RMS; f =1 kHz. 11. Test circuit see Fig.7. September 1989 16 Philips Semiconductors Preliminary specification TV and VTR stereo/dual sound processor with integrated filters and I2C-bus control (1) These pins are not connected internally and should not be connected on the printed-circuit board in order to maintain compatibility with future devices. (2) This potentiometer has to be adjusted to achieve the best stereo separation. (3) Direct connection between pins 5 and 16 is needed. Fig.7 Application and test circuit. September 1989 17 TDA8417 Philips Semiconductors Preliminary specification TV and VTR stereo/dual sound processor with integrated filters and I2C-bus control Voltage input = supply voltage + pulse voltage at 70 Hz = 12 V ± 50 mV (p-p). Fig.8 Ripple rejection test circuit. Fig.9 Total harmonic distortion diagram (stereo mode). September 1989 18 TDA8417 Philips Semiconductors Preliminary specification TV and VTR stereo/dual sound processor with integrated filters and I2C-bus control TDA8417 PACKAGE OUTLINE DIP20: plastic dual in-line package; 20 leads (300 mil) SOT146-1 ME seating plane D A2 A A1 L c e Z b1 w M (e 1) b MH 11 20 pin 1 index E 1 10 0 5 10 mm scale DIMENSIONS (inch dimensions are derived from the original mm dimensions) UNIT A max. A1 min. A2 max. b b1 c mm 4.2 0.51 3.2 1.73 1.30 0.53 0.38 0.36 0.23 26.92 26.54 inches 0.17 0.020 0.13 0.068 0.051 0.021 0.015 0.014 0.009 1.060 1.045 D e e1 L ME MH w Z (1) max. 6.40 6.22 2.54 7.62 3.60 3.05 8.25 7.80 10.0 8.3 0.254 2.0 0.25 0.24 0.10 0.30 0.14 0.12 0.32 0.31 0.39 0.33 0.01 0.078 (1) E (1) Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT146-1 September 1989 REFERENCES IEC JEDEC EIAJ SC603 19 EUROPEAN PROJECTION ISSUE DATE 92-11-17 95-05-24 Philips Semiconductors Preliminary specification TV and VTR stereo/dual sound processor with integrated filters and I2C-bus control TDA8417 with the joint for more than 5 seconds. The total contact time of successive solder waves must not exceed 5 seconds. SOLDERING Introduction There is no soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and surface mounted components are mixed on one printed-circuit board. However, wave soldering is not always suitable for surface mounted ICs, or for printed-circuits with high population densities. In these situations reflow soldering is often used. The device may be mounted up to the seating plane, but the temperature of the plastic body must not exceed the specified maximum storage temperature (Tstg max). If the printed-circuit board has been pre-heated, forced cooling may be necessary immediately after soldering to keep the temperature within the permissible limit. This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our “IC Package Databook” (order code 9398 652 90011). Repairing soldered joints Apply a low voltage soldering iron (less than 24 V) to the lead(s) of the package, below the seating plane or not more than 2 mm above it. If the temperature of the soldering iron bit is less than 300 °C it may remain in contact for up to 10 seconds. If the bit temperature is between 300 and 400 °C, contact may be up to 5 seconds. Soldering by dipping or by wave The maximum permissible temperature of the solder is 260 °C; solder at this temperature must not be in contact DEFINITIONS Data sheet status Objective specification This data sheet contains target or goal specifications for product development. Preliminary specification This data sheet contains preliminary data; supplementary data may be published later. Product specification This data sheet contains final product specifications. Limiting values Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information Where application information is given, it is advisory and does not form part of the specification. LIFE SUPPORT APPLICATIONS These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale. PURCHASE OF PHILIPS I2C COMPONENTS Purchase of Philips I2C components conveys a license under the Philips’ I2C patent to use the components in the I2C system provided the system conforms to the I2C specification defined by Philips. This specification can be ordered using the code 9398 393 40011. September 1989 20