REVISIONS DESCRIPTION Add new device type 09. Update boilerplate to current requirements. Corrections throughout. - CFS LTR A B Update boilerplate paragraphs to current requirements. - phn DATE 06-12-11 APPROVED Thomas M. Hess 12-02-14 Thomas M. Hess CURRENT DESIGN ACTIVITY CAGE CODE 16236 HAS CHANGED NAMES TO: DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 Prepared in accordance with ASME Y14.24 Vendor item drawing REV PAGE REV PAGE REV STATUS OF PAGES PMIC N/A REV B PAGE 1 PREPARED BY B 2 B 3 B 4 Phu H. Nguyen Original date of drawing YY-MM-DD 03-06-18 CHECKED BY Thomas M. Hess A REV AMSC N/A B 6 B 7 B 8 B 9 B 10 B 11 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43218-3990 TITLE Phu H. Nguyen APPROVED BY SIZE B 5 CODE IDENT. NO. MICROCIRCUIT, LINEAR, ULTRALOW-NOISE, HIGH PSRR, FAST RF 200-mA LOW-DROPOUT LINEAR REGULATORS, MONOLITHIC SILICON DWG NO. V62/03634 16236 B PAGE 1 OF 11 5962-V027-12 1. SCOPE 1.1 Scope. This drawing documents the general requirements of ultralow-noise, high PSRR, fast RF 200 mA, low dropout linear regulators, with an operating junction temperature range of -40°C to +125°C for device types 01 through 08, and an operating junction temperature range of -55°C to +125°C for device type 09. 1.2 Vendor Item Drawing Administrative Control Number. The manufacturer’s PIN is the item of identification. The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation: V62/03634 01 Y E Drawing number Device type (See 1.2.1) Case outline (See 1.2.2) Lead finish (See 1.2.3) 1.2.1 Device type(s). 1/ Device Type Generic Output voltage 01 02 03 04 05 06 07 08 09 TPS79301-EP TPS79318-EP TPS79325-EP TPS79328-EP TPS793285-EP TPS79330-EP TPS79333-EP TPS793475-EP TPS79301-EP +1.2 V to 5.5 V +1.8 V +2.5 V +2.8 V +2.85 V +3.0 V +3.3 V +4.75 V +1.2 V to 5.5 V Circuit function Ultra low noise, high PSRR, fast RF 200 mA low dropout linear regulator. Ultra low noise, high PSRR, fast RF 200 mA low dropout linear regulator. Ultra low noise, high PSRR, fast RF 200 mA low dropout linear regulator. Ultra low noise, high PSRR, fast RF 200 mA low dropout linear regulator. Ultra low noise, high PSRR, fast RF 200 mA low dropout linear regulator. Ultra low noise, high PSRR, fast RF 200 mA low dropout linear regulator. Ultra low noise, high PSRR, fast RF 200 mA low dropout linear regulator. Ultra low noise, high PSRR, fast RF 200 mA low dropout linear regulator. Ultra low noise, high PSRR, fast RF 200 mA low dropout linear regulator. 1.2.2 Case outline(s). The case outlines are as specified herein. Outline letter Number of pins X Y 6 5 JEDEC PUB 95 Package style JEDEC MO-178 JEDEC MO-178 Plastic small outline Plastic small outline 1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as provided by the device manufacturer: Finish designator A B C D E Z Material Hot solder dip Tin-lead plate Gold plate Palladium Gold flash palladium Other __________ 1/ Users are cautioned to review the manufacturers data manual for additional user information relating to these devices. DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV B DWG NO. V62/03634 PAGE 2 1.3 Absolute maximum ratings. 1/ Input voltage range (VI) ......................................................................................... Voltage range at EN ............................................................................................. Voltage on OUT ................................................................................................... Peak output current .............................................................................................. ESD rating, HBM .................................................................................................. ESD rating, CDM .................................................................................................. Continuous total power dissipation........................................................................ Operating virtual junction temperature range (TJ): Device types 01 through 08 ........................................................................... Device type 09 ............................................................................................... Storage temperature range (TSTG)......................................................................... -0.3 V to +6.0 V 2/ -0.3 V to VI + 0.3 V -0.3 V to +6.0 V Internally limited 2 kV 500 V See dissipation rating table -40°C to 125°C -55°C to 125°C -65°C to 150°C Dissipation Rating Table – Ambient Temperatures Board Case RθJC RθJA outline Low K 3/ X, Y High K 4/ X, Y 63.75°C/W 63.75°C/W 256°C/W 178.3°C/W Derating factor TA ≤ 25°C TA = 70°C TA = 85°C Above TA = 25°C Power rating Power rating Power rating 3.906 mW/°C 391 mW 215 mW 156 mW 5.609 mW/°C 561 mW 308 mW 224 mW 2. APPLICABLE DOCUMENTS JEDEC – SOLID STATE TECHNOLOGY ASSOCIATION (JEDEC) JEDEC PUB 95 – Registered and Standard Outlines for Semiconductor Devices (Copies of these documents are available online at http:/www.jedec.org or from JEDEC – Solid State Technology Association, 3103 North 10th Street, Suite 240–S, Arlington, VA 22201.) 1/ Stresses beyond those listed under “absolute maximum rating” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 2/ All voltage values are with respect to network terminal ground. 3/ The JEDEC low K (1s) board design used to derive this data was a 3-inch x 3-inch, two layer board with 2 ounce copper traces on top of the board. 4/ The JEDEC high K (2s2p) board design used to derive this data was a 3-inch x 3-inch, multilayer board with 1 ounce internal power and ground planes and 2 ounce copper traces on top and bottom of the board. DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV B DWG NO. V62/03634 PAGE 3 3. REQUIREMENTS 3.1 Marking. Parts shall be permanently and legibly marked with the manufacturer’s part number as shown in 6.3 herein and as follows: A. B. C. Manufacturer’s name, CAGE code, or logo Pin 1 identifier ESDS identification (optional) 3.2 Unit container. The unit container shall be marked with the manufacturer’s part number and with items A and C (if applicable) above. 3.3 Electrical characteristics. The maximum and recommended operating conditions and electrical performance characteristics are as specified in 1.3, 1.4, and table I herein. 3.4 Design, construction, and physical dimension. The design, construction, and physical dimensions are as specified herein. 3.5 Diagrams. 3.5.1 Case outlines. The case outlines shall be as shown in 1.2.2 and on figure 1. 3.5.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.5.3 Block diagrams. The block diagrams shall be as specified on figure 3. DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV B DWG NO. V62/03634 PAGE 4 TABLE I. Electrical performance characteristics. Test Input voltage, VI 1/ Test conditions Devices 01 – 08: TJ = -40°C to 125°C Device 09: TJ = -55°C to 125°C VI = VO(Typ) + 1 V, IO = 1 mA, EN = VI, CO = 10 µF, C(byp) = 0.01 µF unless otherwise specified Device type 2/ Continuous output current, IO 3/ Operating junction temperature, TJ Output voltage 0 µA < IO < 200 mA, 1.22 V ≤ VO ≤ 5.2 V 4/ 0 µA < IO < 200 mA, 5.5 V 0 200 mA 01 - 08 -40 125 °C 09 -55 125 01 0.98 VO 1.02 VO 04 0 µA < IO < 200 mA, 2.8 Typ 05 TJ = 25°C 2.85 Typ 06 TJ = 25°C 3.0 Typ 07 TJ = 25°C 08 TJ = 25°C 0 µA < IO < 200 mA, 5.25 V ≤ VI ≤ 5.5 V 1.22 V ≤ VO ≤ 5.2 V 0 µA < IO < 200 mA, 4/ 09 TJ = 25°C 4.75 Typ 4.845 0.97 VO 1.025 VO 170 Typ 220 All All 5.0 Typ 0.05 Typ 0.12 VO + 1 V < VI ≤ 5.5 V, VO + 1 V < VI ≤ 5.5 V Output noise voltage BW = 200 Hz to 100 kHz, C(byp) = 0.001 µF IO = 200 mA, TJ = 25°C C(byp) = 0.0047 µF 36 Typ C(byp) = 0.01 µF 33 Typ C(byp) = 0.1 µF 32 Typ 04 55 Typ 04 50 Typ C(byp) = 0.001 µF CO = 1 µF, TJ = 25°C C(byp) = 0.0047 µF 70 Typ C(byp) = 0.01 µF 100 Typ VO = 0 V Standby current EN = 0 V, 4/ All 2.7 V ≤ VI ≤ 5.5 V mV %/V µVRMS RL = 14 Ω Output current limit µA All Output voltage line regulation (∆VO/VO) 5/ Time, start up TJ = 25°C 3.366 4.655 All TJ = 25°C 0 µA < IO < 200 mA, 0 µA < IO < 200 mA, 3.06 3.3 Typ 3.234 4.3 V ≤ VI ≤ 5.5 V 0 µA < IO < 200 mA, 2.907 2.94 4.0 V ≤ VI ≤ 5.5 V 0 µA < IO < 200 mA, 2.856 2.793 3.85 V ≤ VI ≤ 5.5 V 0 µA < IO < 200 mA, 2.550 2.744 3.8 V ≤ VI ≤ 5.5 V 0 µA < IO < 200 mA, 1.836 2.5 Typ 2.450 3.5 V ≤ VI ≤ 5.5 V V 1.8 Typ 1.764 TJ = 25°C Load regulation 2.7 All 03 0 µA < IO < 200 mA, Max All 2.8 V ≤ VI ≤ 5.5 V TJ = 25°C Unit Min 02 TJ = 25°C Quiescent current (GND current) Limits 285 All µs 600 mA 1 µA See notes at end of table. DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV B DWG NO. V62/03634 PAGE 5 TABLE I. Electrical performance characteristics - Continued. Test Test conditions Devices 01 – 08: TJ = -40°C to 125°C Device 09: TJ = -55°C to 125°C VI = VO(Typ) + 1 V, IO = 1 mA, EN = VI, CO = 10 µF, C(byp) = 0.01 µF unless otherwise specified High level enable input voltage 2.7 V < VI < 5.5 V Low level enable input voltage 2.7 V < VI < 5.5 V 1/ Device type Limits Min All Max 2.0 V 0.7 V 1 µA 1 µA Input current (EN) EN = 0 Input current (FB) FB = 1.8 V 01, 09 f = 100 Hz, TJ = 25°C, IO = 10 mA 04 f = 100 Hz, TJ = 25°C, IO = 200 mA 68 Typ f = 10 kHz, TJ = 25°C, IO = 200 mA 70 Typ f = 100 kHz, TJ = 25°C, IO = 200 mA 43 Typ Power supply ripple rejection Dropout voltage 6/ -1 IO = 200 mA, 70 Typ TJ = 25°C 04 120 Typ TJ = 25°C 05 120 Typ IO = 200 mA IO = 200 mA 06 TJ = 25°C 112 Typ IO = 200 mA 200 IO = 200 mA, TJ = 25°C 07 102 Typ TJ = 25°C 08 77 Typ IO = 200 mA 180 IO = 200 mA, IO = 200 mA UVLO hysteresis VCC rising, 1/ 2/ 3/ 4/ 5/ 6/ mV 200 IO = 200 mA, VCC rising dB 200 IO = 200 mA, UVLO threshold Unit 125 All 2.25 All TJ = 25°C 2.65 100 Typ V mV Testing and other quality control techniques are used to the extent deemed necessary to assure product performance over the specified temperature range. Product may not necessarily be tested across the full temperature range and all parameters may not necessarily be tested. In the absence of specific parametric testing, product performance is assured by characterization and/or design. To calculate the minimum input voltage for your maximum output current, use the following formula: VI(min) = VO(max) + VDO (max load). Continuous output current and operating junction temperature are limited by internal protection circuitry, but it is not recommended that the device operate under conditions beyond those specified in this table for extended periods of time. The minimum IN operating voltage is 2.7 V or VO(Typ) + 1V, whichever is greater. The maximum IN voltage is 5.5 V. The maximum output current is 200 mA. If VO ≤ 2.5 V then Vimin = 2.7 V, VImax = 5.5 V: V (V − 2 .7 V ) Line Reg. (mV) = (%/V) x O Im ax x 1000 100 If VO ≥ 2.5 V then VImin = VO + 1 V, Vimax = 5.5 V. IN voltage equals VO(Typ) – 100 mV; Device type 03 dropout voltage is limited by the input voltage range limitations. DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV B DWG NO. V62/03634 PAGE 6 Case X Notes: 1. All linear dimensions are in millimeters. 2. This drawing is subject to change without notice. 3. Body dimensions do not include mold flash or protrusions. 4. Leads 1, 2, 3 may be wider than leads 4, 5, 6 for package orientation. 5. Falls within JEDEC MO-178 variation AB, except minimum lead width. FIGURE 1. Case outlines. DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV B DWG NO. V62/03634 PAGE 7 Case Y Notes: 1. All linear dimensions are in millimeters. 2. This drawing is subject to change without notice. 3. Body dimensions do not include mold flash or protrusions. 4. Leads 1, 2, 3 may be wider than leads 4, 5 for package orientation. 5. Falls within JEDEC MO-178 variation AA. FIGURE 1. Case outlines - Continued. DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV B DWG NO. V62/03634 PAGE 8 Cases X, Y Millimeters Symbol Min Max A 0.95 1.45 A1 0.05 b 0.25 c 0.50 0.15 NOM D 2.80 3.00 E 1.50 1.70 E1 2.60 3.00 e 0.95 Typ L 0.35 0.55 FIGURE 1. Case outline - Continued. Terminal number Case X Case Y Terminal symbol Terminal symbol 1 IN IN 2 GND GND 3 EN EN 4 BYPASS BYPASS 5 FB OUT 6 OUT FIGURE 2. Terminal connections. DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV B DWG NO. V62/03634 PAGE 9 FIGURE 3. Block diagrams DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 REV B DWG NO. V62/03634 PAGE 10 4. VERIFICATION 4.1 Product assurance requirements. The manufacturer is responsible for performing all inspection and test requirements as indicated in their internal documentation. Such procedures should include proper handling of electrostatic sensitive devices, classification, packaging, and labeling of moisture sensitive devices, as applicable. 5. PREPARATION FOR DELIVERY 5.1 Packaging. Preservation, packaging, labeling, and marking shall be in accordance with the manufacturer’s standard commercial practices for electrostatic discharge sensitive devices. 6. NOTES 6.1 ESDS. Devices are electrostatic discharge sensitive and are classified as ESDS class 1 minimum. 6.2 Configuration control. The data contained herein is based on the salient characteristics of the device manufacturer’s data book. The device manufacturer reserves the right to make changes without notice. This drawing will be modified as changes are provided. 6.3 Suggested source(s) of supply. Identification of the suggested source(s) of supply herein is not to be construed as a guarantee of present or continued availability as a source of supply for the item. Vendor item drawing administrative control number 1/ Device manufacturer CAGE code V62/03634-01YE 01295 TPS79301DBVREP V62/03634-02XE 01295 TPS79318DBVREP PHHE V62/03634-03XE 01295 TPS79325DBVREP PGWE V62/03634-04XE 3/ TPS79328DBVREP PGXE V62/03634-05XE 3/ TPS793285DBVREP PHIE V62/03634-06XE 3/ TPS79330DBVREP PGYE V62/03634-07XE 01295 TPS793333DBVREP PHUE V62/03634-08XE 01295 TPS793475DBVREP PHJE V62/03634-09XE 01295 TPS79301MDBVREP PMBM 1/ 2/ 3/ Vendor part number 2/ Symbol PGVE The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation. The DBVR indicates tape and reel of 3000 parts. This device is not available from an approved source of supplied. CAGE code 01295 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO Source of supply Texas Instruments, Inc. Semiconductor Group 8505 Forest Lane P.O. Box 660199 Dallas, TX 75243 Point of contact: U.S. Highway 75 South P.O. Box 84, M/S 853 Sherman, TX 75090-9493 SIZE A CODE IDENT NO. 16236 REV B DWG NO. V62/03634 PAGE 11