V6207612 VID

REVISIONS
LTR
DESCRIPTION
DATE
APPROVED
A
Add MIL-STD-883 reference to section 2.
Delete junction temperature reference from
paragraph 1.3. Make change to footnote 3/ as
specified under paragraph 6.3. Update document
paragraphs to current requirements. - ro
14-10-22
C. SAFFLE
CURRENT DESIGN ACTIVITY CAGE CODE 16236
HAS CHANGED NAMES TO:
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
Prepared in accordance with ASME Y14.24
Vendor item drawing
REV
PAGE
REV
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
PAGE
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
REV
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
PAGE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
REV STATUS
OF PAGES
PMIC N/A
PREPARED BY
RICK OFFICER
Original date of drawing
YY-MM-DD
CHECKED BY
RAJESH PITHADIA
07-02-07
TITLE
APPROVED BY
JOSEPH RODENBECK
SIZE
A
REV
AMSC N/A
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
CODE IDENT. NO.
MICROCIRCUIT, DIGITAL-LINEAR, HIGH SPEED
DIFFERENTIAL LINE DRIVERS AND RECEIVERS,
MONOLITHIC SILICON
DWG NO.
V62/07612
16236
A
PAGE
1
OF
32
5962-V105-14
1. SCOPE
1.1 Scope. This drawing documents the general requirements of a high performance high speed differential line drivers and
receivers microcircuit, with an operating temperature range of -55C to +125C.
1.2 Vendor Item Drawing Administrative Control Number. The manufacturers PIN is the item of identification. The vendor item
drawing establishes an administrative control number for identifying the item on the engineering documentation:
V62/07612
-
Drawing
number
01
Y
E
Device type
(See 1.2.1)
Case outline
(See 1.2.2)
Lead finish
(See 1.2.3)
1.2.1 Device type(s).
Device type
Generic
01
02
03
04
SN65LVDS050
SN65LVDS051
SN65LVDS179
SN65LVDS180
Circuit function
High speed differential line drivers and receivers
High speed differential line drivers and receivers
High speed differential line drivers and receivers
High speed differential line drivers and receivers
1.2.2 Case outline(s). The case outline(s) are as specified herein.
Outline letter
Number of pins
N
T
U
X
Y
Z
8
8
14
14
16
16
JEDEC PUB 95
Package style
MO-187-AA
MS-012-AA
MO-153
MS-012-AB
MO-153
MS-012-AC
Plastic surface mount
Plastic surface mount
Plastic surface mount
Plastic surface mount
Plastic surface mount
Plastic surface mount
1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as provided by the device manufacture:
Finish designator
A
B
C
D
E
Z
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
Material
Hot solder dip
Tin-lead plate
Gold plate
Palladium
Gold flash palladium
Other
SIZE
A
CODE IDENT NO.
16236
REV
A
DWG NO.
V62/07612
PAGE
2
1.3 Absolute maximum ratings.
1/
Supply voltage range (VCC) ....................................................................................... -0.5 V to 4 V 2/
Voltage range:
D, R, DE, and RE pins ..........................................................................................
Y, Z, A, and B pins .................................................................................................
Electrostatic discharge (ESD):
Y, Z, A, B, and GND pins .......................................................................................
All pins ...................................................................................................................
Power dissipation (PD) ...............................................................................................
-0.5 V to 6 V
-0.5 V to 4 V
Class 3, A: 12 kV, B: 600 V 3/
Class 3, A: 7 kV, B: 500 V
See 1.5, dissipation ratings table
Storage temperature range (TSTG) ............................................................................ -65C to +150C
Lead temperature 1.6 mm (1/16 inch) from case for 10 seconds ............................... 250C
1.4 Recommended operating conditions. 4/
Supply voltage range (VCC) ....................................................................................... 3 V to 3.6 V
High level input voltage (VIH) ..................................................................................... 2 V minimum
Low level input voltage (VIL) ...................................................................................... 0.8 V maximum
Magnitude of differential input voltage |VID| ............................................................... 0.1 V to 0.6 V
Magnitude of differential output voltage with disabled driver |VOD(dis)| ...................... 520 mV maximum
Driver output voltage (VOY or VOZ) ............................................................................ 0 V to 2.4 V
Common mode input voltage (VIC) (see figure 5) ...................................................... |VID| / 2 V to 2.4 – |VID| / 2 V
VCC – 0.8 V maximum
Operating free-air temperature range (TA) ................................................................. -55C to +125C 5/
1.5 Dissipation ratings table.
1/
2/
3/
4/
5/
6/
Package
TA  25C
power rating
Derating factor
above
TA = 25C 6/
TA = 85C
power rating
TA = 125C
power rating
N
424 mW
3.4 mW/C
220 mW
84 mW
T
635 mW
5.1 mW/C
330 mW
---
U
736 mW
5.9 mW/C
383 mW
---
X
987 mW
7.9 mW/C
513 mW
---
Y
839 mW
6.7 mW/C
437 mW
---
Z
1110 mW
8.9 mW/C
577 mW
---
Stresses beyond those listed under “absolute maximum rating” may cause permanent damage to the device. These are stress
ratings only, and functional operation of the device at these or any other conditions beyond those indicated under
“recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may
affect device reliability.
All voltage values, except differential I/O bus voltages are with respect to network ground terminal.
Tested in accordance with MIL-STD-883C method 3015.7.
Use of this product beyond the manufacturers design rules or stated parameters is done at the user’s risk. The manufacturer
and/or distributor maintain no responsibility or liability for product used beyond the stated limits.
Long term high temperature storage and/or extended use at maximum recommended operating conditions may result in a
reduction of overall device life. See manufacturer for additional information on enhanced plastic packaging.
This is the inverse of the junction to ambient thermal resistance when board mounted and with no air flow.
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
A
DWG NO.
V62/07612
PAGE
3
2. APPLICABLE DOCUMENTS
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-883
-
Test Method Standard Microcircuits.
(Copies of these documents are available online at http://quicksearch.dla.mil or from the Standardization Document Order Desk,
700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
JEDEC Solid State Technology Association
JEDEC PUB 95 –
Registered and Standard Outlines for Semiconductor Devices
(Copies of these documents are available online at http:/www.jedec.org or from JEDEC – Solid State Technology Association,
3103 North 10th Street, Suite 240–S, Arlington, VA 22201-2107).
3. REQUIREMENTS
3.1 Marking. Parts shall be permanently and legibly marked with the manufacturer’s part number as shown in 6.3 herein and as
follows:
A.
B.
C.
Manufacturer’s name, CAGE code, or logo
Pin 1 identifier
ESDS identification (optional)
3.2 Unit container. The unit container shall be marked with the manufacturer’s part number and with items A and C (if applicable)
above.
3.3 Electrical characteristics. The maximum and recommended operating conditions and electrical performance characteristics are
as specified in 1.3, 1.4, and table I herein.
3.4 Design, construction, and physical dimension. The design, construction, and physical dimensions are as specified herein.
3.5 Diagrams.
3.5.1 Case outlines. The case outlines shall be as shown in 1.2.2 and figure 1.
3.5.2 Terminal connections. The terminal connections shall be as shown in figure 2.
3.5.3 Truth tables. The truth tables shall be as shown in figure 3.
3.5.4 Logic diagrams. The logic diagrams shall be as shown in figure 4.
4. VERIFICATION
4.1 Product assurance requirements. The manufacturer is responsible for performing all inspection and test requirements as
indicated in their internal documentation. Such procedures should include proper handling of electrostatic sensitive devices,
classification, packaging, and labeling of moisture sensitive devices, as applicable.
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
A
DWG NO.
V62/07612
PAGE
4
TABLE I. Electrical performance characteristics. 1/
Test
Symbol
Conditions
Temperature,
TA
Device
type
Limits
Min
Unit
Max
Device electrical characteristics section
Supply current
ICC
Drivers and receivers enabled,
no receiver loads,
driver RL = 100 
01
-55C to +125C
20
Drivers enabled, receivers
disabled, RL = 100 
16
Drivers disabled, receivers
enabled, no loads
6
Disabled
1
Drivers enabled, no receiver loads,
driver RL = 100 
02
mA
20
Drivers disabled, no loads
6
No receiver loads,
driver RL = 100 
03
12
Driver and receiver enabled,
no receiver load, driver RL = 100 
04
12
Driver enabled, receiver disabled,
RL = 100 
7
Driver disabled, receiver enabled,
no load
2
Disabled
1
Driver electrical characteristics section
Differential output
voltage magnitude
|VOD|
See figures 6 and 7, RL = 100 
-55C to +125C
All
247
454
mV
Change in differential
output voltage
magnitude between
logic states
|VOD|
See figures 6 and 7, RL = 100 
-55C to +125C
All
-50
50
mV
Steady state common
mode output voltage
VOC(SS)
See figure 8
-55C to +125C
All
1.125
1.375
V
Change in steady
state common mode
output voltage
between logic states
VOC(SS)
See figure 8
-55C to +125C
All
-50
50
mV
See footnotes at end of table.
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
A
DWG NO.
V62/07612
PAGE
5
TABLE I. Electrical performance characteristics – Continued. 1/
Test
Symbol
Conditions
Temperature,
TA
Device
type
Limits
Min
Unit
Max
Driver electrical characteristics section - continued
Peak to peak common
output voltage
VOC(PP)
See figure 8
-55C to +125C
All
150
mV
High level input current
IIH
DE pin, VIH = 5 V
-55C to +125C
All
-20
A
20
D pin, VIH = 5 V
Low level input current
IIL
All
-55C to +125C
DE pin, VIL = 0.8 V
10
D pin, VIL = 0.8 V
Short circuit output
current
IOS
All
-55C to +125C
VOY or VOZ = 0 V
10
IO(OFF)
mA
10
VOD = 0 V
Off state output current
A
-10
All
-55C to +125C
DE = 0 V, VOY or VOZ = 0 V
DE = VCC, VOY or VOZ = 0 V,
-1
1
-1
1
A
VCC  1.5 V
Input capacitance
-55C to +125C
All
See figure 5 and Table II
-55C to +125C
All
See figure 5 and Table II
-55C to +125C
All
-100
mV
IOH = -8 mA
-55C to +125C
All
2.4
V
CIN
3 typical
pF
Receiver electrical characteristics section
Positive going
differential input
voltage threshold
Negative going
differential input
voltage threshold
High level output
voltage
VIT+
VIT-
VOH
100
mV
2.8
IOH = -4 mA
Low level output
voltage
VOL
IOL = 8 mA
-55C to +125C
All
Input current
(A or B inputs)
II
VI = 0
-55C to +125C
All
-2
0.4
V
-20
A
-1.2
VI = 2.4 V
See footnotes at end of table.
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
A
DWG NO.
V62/07612
PAGE
6
TABLE I. Electrical performance characteristics – Continued. 1/
Test
Symbol
Conditions
Temperature,
TA
Device
type
Limits
Min
Unit
Max
Receiver electrical characteristics section - continued
Power off input current
(A or B inputs)
II(OFF)
VCC = 0 V
-55C to +125C
All
20
A
High level input current
(enables)
IIH
VIH = 5 V
-55C to +125C
All
10
A
Low level input current
(enables)
IIL
VIL = 0.8 V
-55C to +125C
All
10
A
High impedance output
current
IOZ
VO = 0 or 5 V
-55C to +125C
All
10
A
Input capacitance
CIN
-55C to +125C
All
5 typical
pF
Driver switching characteristics section
Propagation delay
time, low to high level
output
tPLH
RL = 100 , CL = 10 pF,
see figure 7
-55C to +125C
All
4.5
ns
Propagation delay
time, high to low level
output
tPHL
RL = 100 , CL = 10 pF,
see figure 7
-55C to +125C
All
4.5
ns
Differential output
signal rise time
tr
RL = 100 , CL = 10 pF,
see figure 7
-55C to +125C
All
1.2
ns
Differential output
signal fall time
tf
RL = 100 , CL = 10 pF,
see figure 7
-55C to +125C
All
1.2
ns
Pulse skew
tsk(p)
RL = 100 , CL = 10 pF, 2/
see figure 7
+25C
All
300 typical 3/
ps
Channel to channel
output skew
tsk(o)
RL = 100 , CL = 10 pF, 4/
see figure 7
+25C
All
150 typical 3/
ps
Enable time
ten
See figure 9
-55C to +125C
All
10
ns
Disable time
tdis
See figure 9
-55C to +125C
All
10
ns
(|tPHL – tPLH|)
See footnotes at end of table.
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
A
DWG NO.
V62/07612
PAGE
7
TABLE I. Electrical performance characteristics – Continued. 1/
Test
Symbol
Conditions
Temperature,
TA
Device
type
Limits
Min
Unit
Max
Receiver switching characteristics section
Propagation delay
time, low to high level
output
tPLH
CL = 10 pF, see figure 10
-55C to +125C
All
4.5
ns
Propagation delay
time, high to low level
output
tPHL
CL = 10 pF, see figure 10
-55C to +125C
All
4.5
ns
Pulse skew
tsk(p)
CL = 10 pF, see figure 10 2/
+25C
All
0.3 typical 3/
ns
Output signal rise time
tr
CL = 10 pF, see figure 10
-55C to +125C
All
1.5
ns
Output signal fall time
tf
CL = 10 pF, see figure 10
-55C to +125C
All
1.5
ns
Propagation delay
time, high impedance
to high leveloutput
tPZH
See figure 11
+25C
All
2.5 typical 3/
ns
Propagation delay
time, high impedance
to low level output
tPZL
See figure 11
+25C
All
2.5 typical 3/
ns
Propagation delay
time, high level to
high impedance
output
tPHZ
See figure 11
+25C
All
7 typical 3/
ns
Propagation delay
time, low level to high
impedance output
tPLZ
See figure 11
+25C
All
4 typical 3/
ns
(|tPHL – tPLH|)
1/
Testing and other quality control techniques are used to the extent deemed necessary to assure product performance over
the specified temperature range. Product may not necessarily be tested across the full temperature range and all parameters
may not necessarily be tested. In the absence of specific parametric testing, product performance is assured by characterization
and/or design.
2/
3/
4/
tsk(p) is the magnitude of the time difference between the high to low and low to high propagation delay times at an output.
Typical values are at 25C and with a 3.3 V supply.
tsk(o) is the magnitude of the time difference between the outputs of a single device with all of their inputs connected together.
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
A
DWG NO.
V62/07612
PAGE
8
TABLE II. Receiver minimum and maximum input threshold test voltages.
Applied voltages
Resulting differential
input voltages
Resulting common
mode input voltage
VIA
VIB
VID
VIC
1.25 V
1.15 V
100 mV
1.2 V
1.15 V
1.25 V
-100 mV
1.2 V
2.4 V
2.3 V
100 mV
2.35 V
2.3 V
2.4 V
-100 mV
2.35 V
0.1 V
0V
100 mV
0.05 V
0V
0.1 V
-100 mV
0.05 V
1.5 V
0.9 V
600 mV
1.2 V
0.9 V
1.5 V
-600 mV
1.2 V
2.4 V
1.8 V
600 mV
2.1 V
1.8 V
2.4 V
-600 mV
2.1 V
0.6 V
0V
600 mV
0.3 V
0V
0.6 V
-600 mV
0.3 V
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
A
DWG NO.
V62/07612
PAGE
9
Case N
FIGURE 1. Case outlines.
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
A
DWG NO.
V62/07612
PAGE
10
Case N - continued
Dimensions
Inches
Symbol
Millimeters
Min
Max
Min
Max
A
---
0.043
---
1.10
A1
0.001
0.005
0.05
0.15
b
0.009
0.014
0.25
0.38
c
0.005
0.009
0.13
0.23
D
0.114
0.122
2.90
3.10
E
0.114
0.122
2.90
3.10
E1
0.187
0.198
4.75
5.05
e
L
n
0.025 BSC
0.015
0.65 BSC
0.027
0.40
8
0.70
8
NOTES:
1. Controlling dimensions are millimeter, inch dimensions are given for reference only.
2. For dimension D, body length does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate
burrs shall not exceed 0.15 mm (0.006 inch) per end.
3. For dimension E, body width does not include interlead flash. Interlead flash shall not exceed 0.50 mm ( 0.020 inch)
per side.
4. Falls with JEDEC MO-187-AA, except interlead flash.
FIGURE 1. Case outlines - Continued.
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
A
DWG NO.
V62/07612
PAGE
11
Case T
FIGURE 1. Case outlines – Continued.
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
A
DWG NO.
V62/07612
PAGE
12
Case T - continued
Dimensions
Inches
Symbol
Millimeters
Min
Max
Min
Max
A
---
0.069
---
1.75
A1
0.004
0.010
0.10
0.25
b
0.012
0.020
0.31
0.51
c
0.007
0.010
0.17
0.25
D
0.189
0.197
4.80
5.00
E
0.150
0.157
3.80
4.00
E1
0.228
0.244
5.80
6.20
e
L
n
0.050 BSC
0.016
1.27 BSC
0.050
0.40
8
1.27
8
NOTES:
1. Controlling dimensions are inch, millimeter dimensions are given for reference only.
2. For dimension D, body length does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate
burrs shall not exceed 0.006 inch (0.15 mm) per end.
3. For dimension E, body width does not include interlead flash. Interlead flash shall not exceed 0.017 inch (0.43 mm)
per side.
4. Falls with JEDEC MS-012-AA.
FIGURE 1. Case outlines - Continued.
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
A
DWG NO.
V62/07612
PAGE
13
Case U
FIGURE 1. Case outlines – Continued.
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
A
DWG NO.
V62/07612
PAGE
14
Case U - Continued
Dimensions
Inches
Symbol
Millimeters
Min
Max
Min
Max
A
---
.047
---
1.20
A1
.001
.005
0.05
0.15
b
.007
.011
0.19
0.30
c
.005 NOM
0.15 NOM
D
.192
.200
4.90
5.10
E
.169
.177
4.30
4.50
E1
.244
.259
6.20
6.60
e
L
n
.025 BSC
.019
0.65 BSC
.029
0.50
14
0.75
14
NOTES:
1. Controlling dimensions are millimeter, inch dimensions are given for reference only.
2. For dimension D, body length does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate
burrs shall not exceed 0.15 mm (0.006 inch) per end.
3. For dimension E, body width does not include interlead flash. Interlead flash shall not exceed 0.25 mm (0.009 inch)
per side.
4. Fall within JEDEC MO-153.
FIGURE 1. Case outlines - Continued.
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
A
DWG NO.
V62/07612
PAGE
15
Case X
FIGURE 1. Case outlines – Continued.
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
A
DWG NO.
V62/07612
PAGE
16
Case X - continued
Dimensions
Inches
Symbol
Millimeters
Min
Max
Min
Max
A
---
0.069
---
1.75
A1
0.004
0.010
0.10
0.25
b
0.012
0.020
0.31
0.51
c
0.007
0.010
0.17
0.25
D
0.337
0.344
8.55
8.75
E
0.150
0.157
3.80
4.00
E1
0.228
0.244
5.80
6.20
e
L
n
0.050 BSC
0.016
1.27 BSC
0.050
0.40
14
1.27
14
NOTES:
1. Controlling dimensions are inch, millimeter dimensions are given for reference only.
2. For dimension D, body length does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate
burrs shall not exceed 0.006 inch (0.15 mm) per end.
3. For dimension E, body width does not include interlead flash. Interlead flash shall not exceed 0.017 inch (0.43 mm)
per side.
4. Falls with JEDEC MS-012-AB.
FIGURE 1. Case outlines - Continued.
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
A
DWG NO.
V62/07612
PAGE
17
Case Y
FIGURE 1. Case outlines – Continued.
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
A
DWG NO.
V62/07612
PAGE
18
Case Y - continued
Dimensions
Inches
Symbol
Millimeters
Min
Max
Min
Max
A
---
.047
---
1.20
A1
.001
.005
0.05
0.15
b
.007
.011
0.19
0.30
c
0.005 NOM
0.15 NOM
D
.192
.200
4.90
5.10
E
.169
.177
4.30
4.50
E1
.244
.259
6.20
6.60
e
L
n
.025 BSC
.019
0.65 BSC
.029
0.50
0.75
16
16
NOTES:
1. Controlling dimensions are millimeter, inch dimensions are given for reference only.
2. For dimension D, body length does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate
burrs shall not exceed 0.15 mm (0.006 inch) per end.
3. For dimension E, body width does not include interlead flash. Interlead flash shall not exceed 0.25 mm (0.009 inch)
per side.
4. Fall within JEDEC MO-153.
FIGURE 1. Case outlines - Continued.
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
A
DWG NO.
V62/07612
PAGE
19
Case Z
FIGURE 1. Case outlines – Continued.
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
A
DWG NO.
V62/07612
PAGE
20
Case Z - continued
Dimensions
Inches
Symbol
Millimeters
Min
Max
Min
Max
A
---
0.069
---
1.75
A1
0.004
0.010
0.10
0.25
b
0.012
0.020
0.31
0.51
c
0.007
0.010
0.17
0.25
D
0.386
0.394
9.80
10.00
E
0.150
0.157
3.80
4.00
E1
0.228
0.244
5.80
6.20
e
L
n
0.050 BSC
0.016
1.27 BSC
0.050
0.40
16
1.27
16
NOTES:
1. Controlling dimensions are inch, millimeter dimensions are given for reference only.
2. For dimension D, body length does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions,
or gate burrs shall not exceed 0.006 inch (0.15 mm) per end.
3. For dimension E, body width does not include interlead flash. Interlead flash shall not exceed 0.017 inch (0.43 mm)
per side.
4. Falls with JEDEC MS-012-AC.
FIGURE 1. Case outlines - Continued.
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
A
DWG NO.
V62/07612
PAGE
21
Device types
01
02
03
04
Case outlines
Y and Z
Y and Z
N and T
U and X
Terminal number
Terminal symbol
1
1B
1B
VCC
NC
2
1A
1A
R
R
3
1R
1R
D
RE
4
RE
1DE
GND
DE
5
2R
2R
Y
D
6
2A
2A
Z
GND
7
2B
2B
B
GND
8
GND
GND
A
NC
9
2D
2D
---
Y
10
2Y
2Y
---
Z
11
2Z
2Z
---
B
12
DE
2DE
---
A
13
1Z
1Z
---
VCC
14
1Y
1Y
---
VCC
15
1D
1D
---
---
16
VCC
VCC
---
---
Terminal symbol
Description
A
Receiver input
B
Receiver input
D
Driver input
DE
Driver input
GND
R
Ground
Receiver output
RE
Receiver input
VCC
Supply voltage
Y
Driver output
Z
Driver output
FIGURE 2. Terminal connections.
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
A
DWG NO.
V62/07612
PAGE
22
Device types 01, 02, 04
Receiver
Inputs
Output
VID = VA -VB
RE
R
VID  100 mV
L
H
-100 mV  VID  100 mV
L
?
VID  - 100 mV
L
L
Open
L
H
X
H
Z
Driver
Inputs
Outputs
D
DE
Y
Z
L
H
L
H
H
H
H
L
Open
H
L
H
X
L
OFF
OFF
H = High level
L = Low
Z = High impedance
X = Don’t care
OFF = No output
FIGURE 3. Truth tables.
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
A
DWG NO.
V62/07612
PAGE
23
Device type 03
Receiver
Inputs
Output
VID = VA - VB
R
VID  100 mV
H
-100 mV  VID  100 mV
?
VID  - 100 mV
L
Open
H
Driver
Input
Outputs
D
Y
Z
L
L
H
H
H
L
Open
L
H
H = High level
L = Low
? = Indeterminate
FIGURE 3. Truth tables - continued.
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
A
DWG NO.
V62/07612
PAGE
24
FIGURE 4. Logic diagrams.
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
A
DWG NO.
V62/07612
PAGE
25
FIGURE 5. Receiver voltage definitions.
FIGURE 6. Driver voltage and current definitions.
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
A
DWG NO.
V62/07612
PAGE
26
NOTE:
All input pulses are supplied by a generator having the following characteristics:
tr or tf  1 ns, pulse repetition rate (PRR) = 50 million pulses per second (Mpps), pulse width = 10 0.2 ns.
CL includes instrumentation and fixture capacitance with 0.06 mm of the device under test.
FIGURE 7. Test circuit, timing, and voltage definitions for the differential output signal.
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
A
DWG NO.
V62/07612
PAGE
27
NOTE:
All input pulses are supplied by a generator having the following characteristics:
tr or tf  1 ns, pulse repetition rate (PRR) = 50 Mpps, pulse width = 10 0.2 ns.
CL includes instrumentation and fixture capacitance with 0.06 mm of the device under test.
The measurement of VOC(PP) is made on test equipment with a -3 dB bandwidth of at least 300 MHz.
FIGURE 8. Test circuit and definitions for the driver common mode output voltage.
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
A
DWG NO.
V62/07612
PAGE
28
NOTE:
All input pulses are supplied by a generator having the following characteristics:
tr or tf  1 ns, pulse repetition rate (PRR) = 0.5 Mpps, pulse width = 500 10 ns.
CL includes instrumentation and fixture capacitance with 0.06 mm of the device under test.
FIGURE 9. Enable and disable time circuit and definitions.
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
A
DWG NO.
V62/07612
PAGE
29
NOTE:
All input pulses are supplied by a generator having the following characteristics:
tr or tf  1 ns, pulse repetition rate (PRR) = 50 Mpps, pulse width = 10 0.2 ns.
CL includes instrumentation and fixture capacitance with 0.06 mm of the device under test.
FIGURE 10. Timing test circuit and waveforms.
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
A
DWG NO.
V62/07612
PAGE
30
NOTE:
All input pulses are supplied by a generator having the following characteristics:
tr or tf  1 ns, pulse repetition rate (PRR) = 0.5 Mpps, pulse width = 500 10 ns.
CL includes instrumentation and fixture capacitance with 0.06 mm of the device under test.
FIGURE 11. Enable / disable time test circuit and waveforms.
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
16236
REV
A
DWG NO.
V62/07612
PAGE
31
5. PREPARATION FOR DELIVERY
5.1 Packaging. Preservation, packaging, labeling, and marking shall be in accordance with the manufacturer’s standard commercial
practices for electrostatic discharge sensitive devices.
6. NOTES
6.1 ESDS. Devices are electrostatic discharge sensitive and are classified as ESDS class 1 minimum.
6.2 Configuration control. The data contained herein is based on the salient characteristics of the device manufacturer’s data book.
The device manufacturer reserves the right to make changes without notice. This drawing will be modified as changes are provided.
6.3 Suggested source(s) of supply. Identification of the suggested source(s) of supply herein is not to be construed as a guarantee
of present or continued availability as a source of supply for the item. DLA Land and Maritime maintains an online database of all
current sources of supply at http://www.landandmaritime.dla.mil/Programs/Smcr/.
Vendor item drawing
administrative control
number 1/ 2/
Device
manufacturer
CAGE code
Vendor part number
V62/07612-01YE
3/
SN65LVDS050MPWREP
V62/07612-01ZE
3/
SN65LVDS050MDREP
V62/07612-02YE
3/
SN65LVDS051MPWREP
V62/07612-02ZE
3/
SN65LVDS051MDREP
V62/07612-03NE
01295
SN65LVDS179MDGKREP
V62/07612-03TE
3/
SN65LVDS179MDREP
V62/07612-04UE
3/
SN65LVDS180MPWREP
V62/07612-04XE
3/
SN65LVDS180MDREP
1/ The vendor item drawing establishes an administrative control number
for identifying the item on the engineering documentation.
2/ For the most current packaging and ordering information, see package
drawings, standard packing quantities, thermal data, symbolization,
and PCB design guidelines are available from the manufacturer.
3/ Not available from an approved source.
CAGE code
01295
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
Source of supply
Texas Instruments, Inc.
Semiconductor Group
8505 Forest Ln.
P.O. Box 660199
Dallas, TX 75243
Point of contact: U.S. Highway 75 South
P.O. Box 84, M/S 853
Sherman, TX 75090-9493
SIZE
A
CODE IDENT NO.
16236
REV
A
DWG NO.
V62/07612
PAGE
32