2SK3903 TOSHIBA Field Effect Transistor Silicon N-Channel MOS Type (π-MOSVI) 2SK3903 Switching Regulator Applications • Unit: mm Low drain-source ON resistance: RDS (ON) = 0.32 Ω (typ.) • High forward transfer admittance: ⎪Yfs⎪ = 7.5 S (typ.) • Low leakage current: IDSS = 100 μA (max) (VDS = 600 V) • Enhancement model: Vth = 2.0 to 4.0 V (VDS = 10 V, ID = 1 mA) Absolute Maximum Ratings (Ta = 25°C) Characteristic Symbol Rating Unit Drain-source voltage VDSS 600 V Drain-gate voltage (RGS = 20 kΩ) VDGR 600 V Gate-source voltage VGSS ±30 V A 1. GATE 2. DRAIN (HEATSINK) 3. SOURCE 150 W JEDEC EAS 806 mJ JEITA Avalanche current IAR 14 A Repetitive avalanche energy (Note 3) EAR 15 mJ Channel temperature Tch 150 °C Storage temperature range Tstg −55 to 150 °C DC (Note 1) ID 14 Pulse (Note 1) IDP 56 Drain power dissipation (Tc = 25°C) PD Single pulse avalanche energy (Note 2) Drain current ― SC-65 TOSHIBA 2−16C1B Weight: 4.6 g (typ.) Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (“Handling Precautions”/’’Derating Concept and Methods’’) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Thermal Characteristics 2 Characteristic Symbol Max Unit Thermal resistance, channel to case Rth (ch-c) 0.833 °C/W Thermal resistance, channel to ambient Rth (ch-a) 50 °C/W 1 Note 1: Ensure that the channel temperature does not exceed 150°C during use of the device. Note 2: VDD = 90 V, Tch = 25°C, L = 7.2 mH, RG = 25 Ω, IAR = 14 A Note 3: Repetitive rating: pulse width limited by max junction temperature 3 This transistor is an electrostatic-sensitive device. Handle with care. 1 2009-09-29 2SK3903 Electrical Characteristics (Ta = 25°C) Characteristic Symbol Typ. Max Unit VGS = ±25 V, VDS = 0 V ⎯ ⎯ ±10 μA V (BR) GSS IG = ±10 μA, VDS = 0 V ±30 ⎯ ⎯ V IDSS VDS = 600 V, VGS = 0 V ⎯ ⎯ 100 μA Drain cut-off current Drain-source breakdown voltage Min IGSS Gate leakage current Gate-source breakdown voltage Test Condition V (BR) DSS ID = 10 mA, VGS = 0 V 600 ⎯ ⎯ V Vth VDS = 10 V, ID = 1 mA 2.0 ⎯ 4.0 V Gate threshold voltage Drain-source on resistance RDS (ON) VGS = 10 V, ID = 7 A ⎯ 0.32 0.44 Ω Forward transfer admittance ⎪Yfs⎪ VDS = 10 V, ID = 7 A 2.1 7.5 ⎯ S Input capacitance Ciss ⎯ 3100 ⎯ Reverse transfer capacitance Crss ⎯ 20 ⎯ Output capacitance Coss ⎯ 270 ⎯ ⎯ 70 ⎯ ⎯ 130 ⎯ ⎯ 70 ⎯ ⎯ 280 ⎯ ⎯ 62 ⎯ ⎯ 40 ⎯ ⎯ 22 ⎯ Rise time VDS = 25 V, VGS = 0 V, f = 1 MHz tr 0V ton Switching time Fall time tf Turn-off time Duty ≤ 1%, tw = 10 μs toff Total gate charge (gate-source plus gate-drain) Qg Gate-source charge Qgs Gate-drain (“Miller”) charge Qgd VOUT RL = 29 Ω 50 Ω Turn-on time ID = 7 A 10 V VGS pF ns VDD ≈ 200 V VDD ≈ 400 V, VGS = 10 V, ID = 14 A nC Source-Drain Ratings and Characteristics (Ta = 25°C) Characteristic Symbol Test Condition Min Typ. Max Unit Continuous drain reverse current (Note 1) IDR ⎯ ⎯ ⎯ 14 A Pulse drain reverse current IDRP ⎯ ⎯ ⎯ 56 A (Note 1) Forward voltage (diode) VDSF IDR = 14 A, VGS = 0 V ⎯ ⎯ −1.7 V Reverse recovery time trr IDR = 14 A, VGS = 0 V, ⎯ 1300 ⎯ ns Reverse recovery charge Qrr dIDR/dt = 100 A/μs ⎯ 18 ⎯ μC Marking Note 4: A line under a Lot No. identifies the indication of product Labels. [[G]]/RoHS COMPATIBLE or [[G]]/RoHS [[Pb]] TOSHIBA K3903 Part No. (or abbreviation code) Lot No. Note 4 Please contact your TOSHIBA sales representative for details as to environmental matters such as the RoHS compatibility of Product. The RoHS is the Directive 2002/95/EC of the European Parliament and of the Council of 27 January 2003 on the restriction of the use of certain hazardous substances in electrical and electronic equipment. 2 2009-09-29 2SK3903 ID – VDS ID – VDS COMMON SOURCE Tc = 25°C PULSE TEST 10 20 8.0 10 6.75 8 5.75 6 5.5 4 COMMON SOURCE Tc = 25°C PULSE TEST 8.0 6.0 DRAIN CURRENT ID (A) DRAIN CURRENT ID (A) 10 5.25 5.0 2 6.5 16 6.25 12 6.0 5.75 8 5.5 4 VGS = 5.0 V VGS = 4.5 V 0 0 0 1 2 3 4 5 0 DRAIN−SOURCE VOLTAGE VDS (V) 10 ID – VGS COMMON SOURCE VDS = 20 V PULSE TEST 40 30 40 50 VDS – VGS DRAIN−SOURCE VOLTAGE VDS (V) DRAIN CURRENT ID (A) 30 10 50 25 20 10 100 Tc = −55°C 0 COMMON SOURCE Tc = 25°C PULSE TEST 8 6 ID = 14 A 4 7 2 3.5 0 0 2 4 6 8 10 GATE−SOURCE VOLTAGE VGS 12 14 0 (V) 4 8 100 16 20 (V) RDS (ON) − ID 1 COMMON SOURCE Tc = 25°C PULSE TEST DRAIN−SOURCE ON RESISTANCE RDS (ON) (Ω) COMMON SOURCE VDS = 20 V PULSE TEST Tc = −55°C 12 GATE−SOURCE VOLTAGE VGS ⎪Yfs⎪ − ID FORWARD TRANSFER ADMITTANCE ⎪Yfs⎪ (S) 20 DRAIN−SOURCE VOLTAGE VDS (V) 25 10 100 VGS = 10 V VGS = 15 V 0.1 1 1 10 1 100 DRAIN CURRENT ID (A) 10 100 DRAIN CURRENT ID (A) 3 2009-09-29 2SK3903 RDS (ON) − Tc IDR − VDS 100 COMMON SOURCE VGS = 10 V PULSE TEST 0.8 0.6 ID = 14 A 7 3.5 0.4 0.2 -40 0 40 80 CASE TEMPERATURE 120 Tc 10 1 10 5 3 1 0.1 0.0 160 -0.2 (°C) Vth (V) GATE THRESHOLD VOLTAGE CAPACITANCE C (pF) Ciss 1000 Coss 100 COMMON SOURCE 10 Crss Tc = 25°C 0.1 5 4 3 2 1 10 100 -80 0 40 DRAIN−SOURCE VOLTAGE VDS (V) 500 160 120 80 40 80 120 CASE TEMPERATURE 80 120 160 Tc (°C) DYNAMIC INPUT/OUTPUT CHARACTERISTICS 200 PD (W) -40 CASE TEMPERATURE PD − Tc DRAIN POWER DISSIPATION -1.2 0 1 40 -1.0 COMMON SOURCE VDS = 10 V ID = 1 mA PULSE TEST DRAIN−SOURCE VOLTAGE VDS (V) 0 0 -0.8 Vth − Tc CAPACITANCE – VDS f = 1 MHz -0.6 DRAIN−SOURCE VOLTAGE VDS (V) 10000 VGS = 0 V VGS = 0, −1 V -0.4 160 Tc VDS 400 300 20 COMMON SOURCE ID = 14 A Tc = 25°C PULSE TEST (V) 0 -80 COMMON SOURCE Tc = 25°C PULSE TEST 16 12 VDS = 100 V 400 200 200 8 VGS 4 100 0 0 200 GATE−SOURCE VOLTAGE VGS 1 DRAIN REVERSE CURRENT IDR (A) DRAIN−SOURCE ON RESISTANCE RDS (ON) (Ω) 1.2 0 20 40 60 80 100 TOTAL GATE CHARGE Qg (nC) (°C) 4 2009-09-29 2SK3903 rth − tw NORMALIZED TRANSIENT THERMAL IMPEDANCE rth (t)/Rth (ch-a) 10 1 Duty = 0.5 0.2 0.1 0.1 0.05 0.02 0.01 0.01 PDM SINGLE PULSE t T Duty = t/T Rth (ch-c) = 0.833°C/W 0.001 10 μ 100 μ 1m 10 m 100 m PULSE WIDTH tw 1 (s) SAFE OPERATING AREA EAS – Tch 100 AVALANCHE ENERGY EAS (mJ) 1000 ID max (PULSE) * DRAIN CURRENT ID (A) 10 100 μs * 1 ms * 10 ID max (CONTINUOUS) 1 DC OPERATION Tc = 25°C * SINGLE NONPETITIVE PULSE Tc = 25°C 0.1 800 600 400 200 Curves must be derated linearly with 0 increase in temperature. VDSS max 25 0.01 1 10 100 50 75 100 CHANNEL TEMPERATURE (INITIAL) 1000 125 150 Tch (°C) DRAIN−SOURCE VOLTAGE VDS (V) 15 V BVDSS IAR −15 V VDD TEST CIRCUIT RG = 25 Ω VDD = 90 V, L = 7.2 mH 5 VDS WAVE FORM Ε AS = ⎛ ⎞ 1 B VDSS ⎟ ⋅ L ⋅ I2 ⋅ ⎜ ⎜B ⎟ − 2 V VDSS DD ⎝ ⎠ 2009-09-29 2SK3903 RESTRICTIONS ON PRODUCT USE • Toshiba Corporation, and its subsidiaries and affiliates (collectively “TOSHIBA”), reserve the right to make changes to the information in this document, and related hardware, software and systems (collectively “Product”) without notice. • This document and any information herein may not be reproduced without prior written permission from TOSHIBA. Even with TOSHIBA’s written permission, reproduction is permissible only if reproduction is without alteration/omission. • Though TOSHIBA works continually to improve Product’s quality and reliability, Product can malfunction or fail. Customers are responsible for complying with safety standards and for providing adequate designs and safeguards for their hardware, software and systems which minimize risk and avoid situations in which a malfunction or failure of Product could cause loss of human life, bodily injury or damage to property, including data loss or corruption. Before creating and producing designs and using, customers must also refer to and comply with (a) the latest versions of all relevant TOSHIBA information, including without limitation, this document, the specifications, the data sheets and application notes for Product and the precautions and conditions set forth in the “TOSHIBA Semiconductor Reliability Handbook” and (b) the instructions for the application that Product will be used with or for. Customers are solely responsible for all aspects of their own product design or applications, including but not limited to (a) determining the appropriateness of the use of this Product in such design or applications; (b) evaluating and determining the applicability of any information contained in this document, or in charts, diagrams, programs, algorithms, sample application circuits, or any other referenced documents; and (c) validating all operating parameters for such designs and applications. TOSHIBA ASSUMES NO LIABILITY FOR CUSTOMERS’ PRODUCT DESIGN OR APPLICATIONS. • Product is intended for use in general electronics applications (e.g., computers, personal equipment, office equipment, measuring equipment, industrial robots and home electronics appliances) or for specific applications as expressly stated in this document. Product is neither intended nor warranted for use in equipment or systems that require extraordinarily high levels of quality and/or reliability and/or a malfunction or failure of which may cause loss of human life, bodily injury, serious property damage or serious public impact (“Unintended Use”). Unintended Use includes, without limitation, equipment used in nuclear facilities, equipment used in the aerospace industry, medical equipment, equipment used for automobiles, trains, ships and other transportation, traffic signaling equipment, equipment used to control combustions or explosions, safety devices, elevators and escalators, devices related to electric power, and equipment used in finance-related fields. Do not use Product for Unintended Use unless specifically permitted in this document. • Do not disassemble, analyze, reverse-engineer, alter, modify, translate or copy Product, whether in whole or in part. • Product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable laws or regulations. • The information contained herein is presented only as guidance for Product use. No responsibility is assumed by TOSHIBA for any infringement of patents or any other intellectual property rights of third parties that may result from the use of Product. No license to any intellectual property right is granted by this document, whether express or implied, by estoppel or otherwise. • ABSENT A WRITTEN SIGNED AGREEMENT, EXCEPT AS PROVIDED IN THE RELEVANT TERMS AND CONDITIONS OF SALE FOR PRODUCT, AND TO THE MAXIMUM EXTENT ALLOWABLE BY LAW, TOSHIBA (1) ASSUMES NO LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, INDIRECT, CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES OR LOSS, INCLUDING WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF OPPORTUNITIES, BUSINESS INTERRUPTION AND LOSS OF DATA, AND (2) DISCLAIMS ANY AND ALL EXPRESS OR IMPLIED WARRANTIES AND CONDITIONS RELATED TO SALE, USE OF PRODUCT, OR INFORMATION, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, ACCURACY OF INFORMATION, OR NONINFRINGEMENT. • Do not use or otherwise make available Product or related software or technology for any military purposes, including without limitation, for the design, development, use, stockpiling or manufacturing of nuclear, chemical, or biological weapons or missile technology products (mass destruction weapons). Product and related software and technology may be controlled under the Japanese Foreign Exchange and Foreign Trade Law and the U.S. Export Administration Regulations. Export and re-export of Product or related software or technology are strictly prohibited except in compliance with all applicable export laws and regulations. • Please contact your TOSHIBA sales representative for details as to environmental matters such as the RoHS compatibility of Product. Please use Product in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. TOSHIBA assumes no liability for damages or losses occurring as a result of noncompliance with applicable laws and regulations. 6 2009-09-29