ONSEMI MC14551B

MC14551B
Quad 2-Channel Analog
Multiplexer/Demultiplexer
The MC14551B is a digitally–controlled analog switch. This device
implements a 4PDT solid state switch with low ON impedance and
very low OFF Leakage current. Control of analog signals up to the
complete supply voltage range can be achieved.
http://onsemi.com
• Triple Diode Protection on All Control Inputs
• Supply Voltage Range = 3.0 Vdc to 18 Vdc
• Analog Voltage Range (VDD – VEE) = 3.0 to 18 V
•
•
•
•
MARKING
DIAGRAMS
16
Note: VEE must be VSS
Linearized Transfer Characteristics
Low Noise — 12 nV√Cycle, f ≥ 1.0 kHz typical
For Low RON, Use The HC4051, HC4052, or HC4053 High–Speed
CMOS Devices
Switch Function is Break Before Make
PDIP–16
P SUFFIX
CASE 648
1
16
SOIC–16
D SUFFIX
CASE 751B
MAXIMUM RATINGS (2.)
VDD
Vin, Vout
Parameter
DC Supply Voltage Range
(Referenced to VEE, VSS ≥ VEE)
Input Current (DC or Transient),
per Control Pin
Isw
Switch Through Current
Unit
V
– 0.5 to VDD + 0.5
V
16
SOEIAJ–16
F SUFFIX
CASE 966
MC14551B
ALYW
1
Input or Output Voltage (DC or
Transient) (Referenced to VSS for
Control Input & VEE for Switch I/O)
Iin
Value
– 0.5 to + 18.0
14551B
AWLYWW
1
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
Symbol
MC14551BCP
AWLYYWW
(3.)
± 10
mA
± 25
mA
500
mW
PD
Power Dissipation, per Package
TA
Ambient Temperature Range
– 55 to + 125
C
Tstg
Storage Temperature Range
– 65 to + 150
C
TL
Lead Temperature
(8–Second Soldering)
260
C
2. Maximum Ratings are those values beyond which damage to the device
may occur.
3. Temperature Derating:
Plastic “P and D/DW” Packages: – 7.0 mW/C From 65C To 125C
A
WL, L
YY, Y
WW, W
= Assembly Location
= Wafer Lot
= Year
= Work Week
ORDERING INFORMATION
Device
Package
Shipping
MC14551BCP
PDIP–16
2000/Box
MC14551BD
SOIC–16
48/Rail
MC14551BDR2
SOIC–16
2500/Tape & Reel
SOEIAJ–16
See Note 1.
MC14551BF
1. For ordering information on the EIAJ version of
the SOIC packages, please contact your local
ON Semiconductor representative.
This device contains protection circuitry to guard against damage due to high
static voltages or electric fields. However, precautions must be taken to avoid
applications of any voltage higher than maximum rated voltages to this
high–impedance circuit. For proper operation, Vin and Vout should be constrained
to the range VSS (Vin or Vout) VDD for control inputs and VEE ≤ (Vin or Vout) ≤
VDD for Switch I/O.
Unused inputs must always be tied to an appropriate logic voltage level (e.g.,
either VSS, VEE or VDD). Unused outputs must be left open.
 Semiconductor Components Industries, LLC, 2000
August, 2000 – Rev. 4
1
Publication Order Number:
MC14551B/D
MC14551B
PIN ASSIGNMENT
W1
1
16
VDD
X0
2
15
W0
X1
3
14
W
X
4
13
Z
Y
5
12
Z1
Y0
6
11
Z0
VEE
7
10
Y1
VSS
8
9
9
SWITCHES
IN/OUT
VDD = Pin 16
VSS = Pin 8
VEE = Pin 7
15
1
2
3
6
10
11
12
CONTROL
W
W0
W1
X0
X1
Y0
Y1
Z0
Z1
X
CONTROL
14
4
COMMONS
OUT/IN
Y
5
Z
13
Control
ON
0
W0 X0 Y0 Z0
1
W1 X1 Y1 Z1
NOTE: Control Input referenced to VSS, Analog Inputs and
Outputs reference to VEE. VEE must be VSS.
http://onsemi.com
2
MC14551B
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ELECTRICAL CHARACTERISTICS
– 55C
Characteristic
Symbol
VDD
Test Conditions
25C
125C
Min
Max
Min
Typ (4.)
Max
Min
Max
Unit
SUPPLY REQUIREMENTS (Voltages Referenced to VEE)
Power Supply Voltage
Range
VDD
—
VDD – 3.0 ≥ VSS ≥
VEE
3.0
18
3.0
—
18
3.0
18
V
Quiescent Current Per
Package
IDD
5.0
10
15
Control Inputs: Vin =
VSS or VDD,
Switch I/O: VEE VI/O
VDD, and ∆Vswitch
500 mV (5.)
—
—
—
5.0
10
20
—
—
—
0.005
0.010
0.015
5.0
10
20
—
—
—
150
300
600
µA
ID(AV)
5.0
10
15
TA = 25C only (The
channel component,
(Vin – Vout)/Ron, is
not included.)
Total Supply Current
(Dynamic Plus
Quiescent, Per Package)
Typical
µA
(0.07 µA/kHz) f + IDD
(0.20 µA/kHz) f + IDD
(0.36 µA/kHz) f + IDD
CONTROL INPUT (Voltages Referenced to VSS)
Low–Level Input Voltage
VIL
5.0
10
15
Ron = per spec,
Ioff = per spec
—
—
—
1.5
3.0
4.0
—
—
—
2.25
4.50
6.75
1.5
3.0
4.0
—
—
—
1.5
3.0
4.0
V
High–Level Input Voltage
VIH
5.0
10
15
Ron = per spec,
Ioff = per spec
3.5
7.0
11
—
—
—
3.5
7.0
11
2.75
5.50
8.25
—
—
—
3.5
7.0
11
—
—
—
V
Input Leakage Current
Iin
15
Vin = 0 or VDD
—
±0.1
—
±0.00001
±0.1
—
±1.0
µA
Input Capacitance
Cin
—
—
—
—
5.0
7.5
—
—
pF
SWITCHES IN/OUT AND COMMONS OUT/IN — W, X, Y, Z (Voltages Referenced to VEE)
Recommended Peak–to–
Peak Voltage Into or Out
of the Switch
VI/O
—
Channel On or Off
0
VDD
0
—
VDD
0
VDD
Vp–p
Recommended Static or
Dynamic Voltage Across
the Switch (5.) (Figure 3)
∆Vswitch
—
Channel On
0
600
0
—
600
0
300
mV
Output Offset Voltage
VOO
—
Vin = 0 V, No Load
—
—
—
10
—
—
—
µV
ON Resistance
Ron
5.0
10
15
∆Vswitch 500 mV (5.),
Vin = VIL or VIH
(Control), and Vin =
0 to VDD (Switch)
—
—
800
400
220
—
—
—
250
120
80
1050
500
280
—
—
—
1200
520
300
Ω
∆Ron
5.0
10
15
—
—
—
70
50
45
—
—
—
25
10
10
70
50
45
—
—
—
135
95
65
Ω
Ioff
15
Vin = VIL or VIH
(Control) Channel to
Channel or Any One
Channel
—
±100
—
±0.05
±100
—
±1000
nA
Capacitance, Switch I/O
CI/O
—
Switch Off
—
—
—
10
—
—
—
pF
Capacitance, Common O/I
CO/I
—
—
—
—
17
—
—
—
pF
Capacitance, Feedthrough
(Channel Off)
CI/O
—
—
—
—
—
—
—
—
0.15
0.47
—
—
—
—
—
—
pF
∆ON Resistance Between
Any Two Channels
in the Same Package
Off–Channel Leakage
Current (Figure 8)
Pins Not Adjacent
Pins Adjacent
4. Data labeled “Typ” is not to be used for design purposes, but is intended as an indication of the IC’s potential performance.
5. For voltage drops across the switch (∆Vswitch) > 600 mV ( > 300 mV at high temperature), excessive VDD current may be drawn; i.e. the
current out of the switch may contain both VDD and switch input components. The reliability of the device will be unaffected unless the
Maximum Ratings are exceeded. (See first page of this data sheet.)
http://onsemi.com
3
MC14551B
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ELECTRICAL CHARACTERISTICS (CL = 50 pF, TA = 25C, VEE VSS)
Characteristic
Symbol
Propagation Delay Times
Switch Input to Switch Output (RL = 10 kΩ)
tPLH, tPHL = (0.17 ns/pF) CL + 26.5 ns
tPLH, tPHL = (0.08 ns/pF) CL + 11 ns
tPLH, tPHL = (0.06 ns/pF) CL + 9.0 ns
tPLH, tPHL
Control Input to Output (RL = 10 kΩ)
VEE = VSS (Figure 4)
tPLH, tPHL
VDD – VEE
Vdc
Min
Typ (6.)
Max
Unit
ns
5.0
10
15
—
—
—
35
15
12
90
40
30
5.0
10
15
—
—
—
350
140
100
875
350
250
—
10
—
0.07
—
%
BW
10
—
17
—
MHz
Off Channel Feedthrough Attenuation, Figure 5
RL = 1 kΩ, Vin = 1/2 (VDD – VEE) p–p,
fin = 55 MHz
—
10
—
– 50
—
dB
Channel Separation (Figure 6)
RL = 1 kΩ, Vin = 1/2 (VDD – VEE) p–p,
fin = 3 MHz
—
10
—
– 50
—
dB
Crosstalk, Control Input to Common O/I, Figure 7
R1 = 1 kΩ, RL = 10 kΩ,
Control tr = tf = 20 ns
—
10
—
75
—
mV
Second Harmonic Distortion
RL = 10 kΩ, f = 1 kHz, Vin = 5 Vp–p
Bandwidth (Figure 5)
RL = 1 kΩ, Vin = 1/2 (VDD – VEE) p–p,
20 Log (Vout/Vin) = – 3 dB, CL = 50 pF
ns
6. Data labelled “Typ” is not to be used for design purposes but is intended as an indication of the IC’s potential performance.
http://onsemi.com
4
MC14551B
VDD
VDD
VDD
IN/OUT
OUT/IN
VEE
VDD
LEVEL
CONVERTED
CONTROL
IN/OUT
OUT/IN
CONTROL
VEE
Figure 1. Switch Circuit Schematic
16
CONTROL9
VDD
LEVEL
CONVERTER
8
VSS
7
CONTROL
VEE
W015
14W
W11
X02
4X
X13
Y06
5Y
Y110
Z011
13Z
Z112
Figure 2. MC14551B Functional Diagram
http://onsemi.com
5
MC14551B
TEST CIRCUITS
ON SWITCH
CONTROL
SECTION
OF IC
PULSE
GENERATOR
V
CONTROL
LOAD
Vout
RL
CL
SOURCE
VDD VEE
Figure 3. ∆V Across Switch
VEE VDD
Figure 4. Propagation Delay Times,
Control to Output
Control input used to turn ON or OFF
the switch under test.
RL
ON
CONTROL
Vout
RL
CONTROL
OFF
CL = 50 pF
Vout
RL
Vin
VDD - VEE
2
Vin
VDD - VEE
2
Figure 5. Bandwidth and Off–Channel
Feedthrough Attenuation
CL = 50 pF
Figure 6. Channel Separation
(Adjacent Channels Used for Setup)
OFF CHANNEL UNDER TEST
VDD
CONTROL
CONTROL
SECTION
OF IC
Vout
RL
VEE
OTHER
CHANNEL(S)
CL = 50 pF
VEE
VDD
R1
VEE
VDD
Figure 7. Crosstalk, Control Input
to Common O/I
Figure 8. Off Channel Leakage
VDD
KEITHLEY 160
DIGITAL
MULTIMETER
10 k
1 kΩ
RANGE
VDD
VEE = VSS
Figure 9. Channel Resistance (RON) Test Circuit
http://onsemi.com
6
X/Y
PLOTTER
MC14551B
350
300
300
250
200
150
TA = 125°C
100
25°C
-55°C
50
0
-10
RON, ON" RESISTANCE (OHMS)
RON, ON" RESISTANCE (OHMS)
350
-8.0 -6.0
-4.0 -2.0
0
2.0
4.0
6.0
8.0
250
200
150
TA = 125°C
100
25°C
-55°C
50
0
-10
10
-4.0 -2.0
0
2.0
4.0
6.0
8.0
Vin, INPUT VOLTAGE (VOLTS)
Figure 10. VDD @ 7.5 V, VEE @ – 7.5 V
Figure 11. VDD @ 5.0 V, VEE @ – 5.0 V
700
350
600
300
500
400
300
TA = 125°C
200
25°C
100
0
-10
-8.0 -6.0
Vin, INPUT VOLTAGE (VOLTS)
RON, ON" RESISTANCE (OHMS)
RON, ON" RESISTANCE (OHMS)
TYPICAL RESISTANCE CHARACTERISTICS
-55°C
-8.0 -6.0
-4.0 -2.0
0
2.0
4.0
6.0
8.0
TA = 25°C
VDD = 2.5 V
250
200
150
5.0 V
100
7.5 V
50
0
-10
10
-8.0 -6.0
-4.0 -2.0
0
2.0
4.0
6.0
8.0
Vin, INPUT VOLTAGE (VOLTS)
Vin, INPUT VOLTAGE (VOLTS)
Figure 12. VDD @ 2.5 V, VEE @ – 2.5 V
Figure 13. Comparison at 25C, VDD @ – VEE
http://onsemi.com
7
10
10
MC14551B
APPLICATIONS INFORMATION
margin at each peak. If voltage transients above VDD and/or
below VEE are anticipated on the analog channels, external
diodes (Dx) are recommended as shown in Figure B. These
diodes should be small signal types able to absorb the
maximum anticipated current surges during clipping.
The absolute maximum potential difference between
VDD and VEE is 18.0 volts. Most parameters are specified
up to 15 volts which is the recommended maximum
difference between VDD and VEE.
Balanced supplies are not required. However, V SS must
be greater than or equal to VEE. For example, VDD =
+ 10 volts, VSS = + 5 volts, and VEE = – 3 volts is acceptable.
See the table below.
Figure A illustrates use of the on–chip level converter
detailed in Figure 2. The 0–to–5 volt Digital Control signal
is used to directly control a 9 Vp–p analog signal.
The digital control logic levels are determined by VDD
and VSS. The VDD voltage is the logic high voltage; the VSS
voltage is logic low. For the example, VDD = + 5 V = logic
high at the control inputs; V SS = GND = 0 V = logic low.
The maximum analog signal level is determined by V DD
and VEE. The VDD voltage determines the maximum
recommended peak above VSS. The VEE voltage
determines the maximum swing below VSS. For the
example, VDD – VSS = 5 volt maximum swing above VSS;
VSS – VEE = 5 volt maximum swing below VSS. The
example shows a ± 4.5 volt signal which allows a 1/2 volt
+5 V
-5 V
VSS
VDD
9 Vp-p
+5 V
ANALOG SIGNAL
EXTERNAL
CMOS
DIGITAL
CIRCUITRY
SWITCH
I/O
VEE
+4.5 V
COMMON
O/I
9 Vp-p
GND
ANALOG SIGNAL
MC14551B
0-TO-5 V DIGITAL
-4.5 V
CONTROL
CONTROL SIGNAL
Figure A. Application Example
VDD
VDD
Dx
Dx
SWITCH
I/O
COMMON
O/I
Dx
Dx
VEE
VEE
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
Figure B. External Schottky or Germanium Clipping Diodes
POSSIBLE SUPPLY CONNECTIONS
VDD
In Volts
VSS
In Volts
VEE
In Volts
Control Inputs
Logic High/Logic Low
In Volts
Maximum Analog Signal Range
In Volts
+8
0
–8
+ 8/0
+ 8 to – 8 = 16 Vp–p
+5
0
– 12
+ 5/0
+ 5 to – 12 = 17 Vp–p
+5
0
0
+ 5/0
+ 5 to 0 = 5 Vp–p
+5
0
–5
+ 5/0
+ 5 to – 5 = 10 Vp–p
–5
+ 10/ + 5
+ 10 to – 5 = 15 Vp–p
+ 10
http://onsemi.com
8
MC14551B
PACKAGE DIMENSIONS
PDIP–16
P SUFFIX
CASE 648–08
ISSUE R
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEADS WHEN
FORMED PARALLEL.
4. DIMENSION B DOES NOT INCLUDE MOLD FLASH.
5. ROUNDED CORNERS OPTIONAL.
–A–
16
9
1
8
B
F
C
L
S
–T–
SEATING
PLANE
K
H
G
D
M
J
16 PL
0.25 (0.010)
M
T A
M
http://onsemi.com
9
DIM
A
B
C
D
F
G
H
J
K
L
M
S
INCHES
MIN
MAX
0.740
0.770
0.250
0.270
0.145
0.175
0.015
0.021
0.040
0.70
0.100 BSC
0.050 BSC
0.008
0.015
0.110
0.130
0.295
0.305
0
10 0.020
0.040
MILLIMETERS
MIN
MAX
18.80
19.55
6.35
6.85
3.69
4.44
0.39
0.53
1.02
1.77
2.54 BSC
1.27 BSC
0.21
0.38
2.80
3.30
7.50
7.74
0
10 0.51
1.01
MC14551B
PACKAGE DIMENSIONS
SOIC–16
D SUFFIX
CASE 751B–05
ISSUE J
–A–
16
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
9
–B–
1
P
8 PL
0.25 (0.010)
8
M
B
S
G
R
K
F
X 45 C
–T–
SEATING
PLANE
J
M
D
16 PL
0.25 (0.010)
M
T B
S
A
S
http://onsemi.com
10
DIM
A
B
C
D
F
G
J
K
M
P
R
MILLIMETERS
MIN
MAX
9.80
10.00
3.80
4.00
1.35
1.75
0.35
0.49
0.40
1.25
1.27 BSC
0.19
0.25
0.10
0.25
0
7
5.80
6.20
0.25
0.50
INCHES
MIN
MAX
0.386
0.393
0.150
0.157
0.054
0.068
0.014
0.019
0.016
0.049
0.050 BSC
0.008
0.009
0.004
0.009
0
7
0.229
0.244
0.010
0.019
MC14551B
PACKAGE DIMENSIONS
SOEIAJ–16
F SUFFIX
PLASTIC EIAJ SOIC PACKAGE
CASE 966–01
ISSUE O
16
LE
9
Q1
M
E HE
1
8
L
DETAIL P
Z
D
e
VIEW P
A
A1
b
0.13 (0.005)
c
M
0.10 (0.004)
http://onsemi.com
11
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS D AND E DO NOT INCLUDE
MOLD FLASH OR PROTRUSIONS AND ARE
MEASURED AT THE PARTING LINE. MOLD FLASH
OR PROTRUSIONS SHALL NOT EXCEED 0.15
(0.006) PER SIDE.
4. TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
5. THE LEAD WIDTH DIMENSION (b) DOES NOT
INCLUDE DAMBAR PROTRUSION. ALLOWABLE
DAMBAR PROTRUSION SHALL BE 0.08 (0.003)
TOTAL IN EXCESS OF THE LEAD WIDTH
DIMENSION AT MAXIMUM MATERIAL CONDITION.
DAMBAR CANNOT BE LOCATED ON THE LOWER
RADIUS OR THE FOOT. MINIMUM SPACE
BETWEEN PROTRUSIONS AND ADJACENT LEAD
TO BE 0.46 ( 0.018).
DIM
A
A1
b
c
D
E
e
HE
L
LE
M
Q1
Z
MILLIMETERS
MIN
MAX
--2.05
0.05
0.20
0.35
0.50
0.18
0.27
9.90
10.50
5.10
5.45
1.27 BSC
7.40
8.20
0.50
0.85
1.10
1.50
10 0
0.70
0.90
--0.78
INCHES
MIN
MAX
--0.081
0.002
0.008
0.014
0.020
0.007
0.011
0.390
0.413
0.201
0.215
0.050 BSC
0.291
0.323
0.020
0.033
0.043
0.059
10 0
0.028
0.035
--0.031
MC14551B
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes
without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular
purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability,
including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be
validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others.
SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or
death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold
SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable
attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer.
PUBLICATION ORDERING INFORMATION
NORTH AMERICA Literature Fulfillment:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303–675–2175 or 800–344–3860 Toll Free USA/Canada
Fax: 303–675–2176 or 800–344–3867 Toll Free USA/Canada
Email: [email protected]
Fax Response Line: 303–675–2167 or 800–344–3810 Toll Free USA/Canada
N. American Technical Support: 800–282–9855 Toll Free USA/Canada
CENTRAL/SOUTH AMERICA:
Spanish Phone: 303–308–7143 (Mon–Fri 8:00am to 5:00pm MST)
Email: ONlit–[email protected]
ASIA/PACIFIC: LDC for ON Semiconductor – Asia Support
Phone: 303–675–2121 (Tue–Fri 9:00am to 1:00pm, Hong Kong Time)
Toll Free from Hong Kong & Singapore:
001–800–4422–3781
Email: ONlit–[email protected]
JAPAN: ON Semiconductor, Japan Customer Focus Center
4–32–1 Nishi–Gotanda, Shinagawa–ku, Tokyo, Japan 141–0031
Phone: 81–3–5740–2745
Email: [email protected]
EUROPE: LDC for ON Semiconductor – European Support
German Phone: (+1) 303–308–7140 (Mon–Fri 2:30pm to 7:00pm CET)
Email: ONlit–[email protected]
French Phone: (+1) 303–308–7141 (Mon–Fri 2:00pm to 7:00pm CET)
Email: ONlit–[email protected]
English Phone: (+1) 303–308–7142 (Mon–Fri 12:00pm to 5:00pm GMT)
Email: [email protected]
ON Semiconductor Website: http://onsemi.com
EUROPEAN TOLL–FREE ACCESS*: 00–800–4422–3781
*Available from Germany, France, Italy, UK
For additional information, please contact your local
Sales Representative.
http://onsemi.com
12
MC14551B/D