SANYO TN6R05

TN6R05
Ordering number : ENN8034
ExPD (Excellent Power Device)
TN6R05
Switching Regulator IC for RCC
Method Power Supplies Applications
Features
•
•
•
•
•
Original contorol IC for Delay RCC-type.
High voltage power MOSFET with current sense.
Overload protection.
Only few external components required.
Small Full-Isolation package : TO-220FI5H.
Specifications
Absolute Maximum Ratings at Ta=25°C
Parameter
Symbol
Drain-to-Source Voltage
Drain Current (DC)
Drain Current (Pulse)
Conditions
Ratings
Unit
VDS
650
V
ID
6.5
A
IC Input Voltage
IDP
VIN
Allowable Power Dissipation
PD
Operating Temperature
Topr
Junction Temperature
Tj
Storage Temperature
Tstg
PW≤10µs, duty cycle≤1%
Tc=25°C
19.5
A
30
V
2.0
W
40
W
--25 to +125
°C
150
°C
--55 to +150
°C
Electrical Characteristics at Ta=25°C
Parameter
Symbol
Conditions
Ratings
min
typ
max
Unit
[MOSFET]
Drain-to-Source Breakdown Voltage
Zero-Gate Voltage Drain Current
Cutoff Voltage
Static Drain-to-Source On-State Resistance
Input Capacitance
Output Capacitance
V(BR)DSS
IDSS
VGS(off)
RDS(on)
Ciss
Coss
ID=1mA, VDELAY=0
VDS=650V, VDELAY=0
650
VDS=10V, ID=1mA
ID=3.3A, VDELAY=15V
3.0
V
1.0
0.95
VDS=20V, f=1MHz
VDS=20V, f=1MHz
mA
4.0
V
1.2
Ω
1900
pF
310
pF
[IC]
Restriction of Drive Voltage
VIN(OV)
Detection Voltage of Feedback and
Overload Amplifier
VFB
IIN=1mA, VFB=0
30
VDELAY, VIN=10V, IIN=50mA
V
2.0
V
Any and all SANYO products described or contained herein do not have specifications that can handle
applications that require extremely high levels of reliability, such as life-support systems, aircraft's
control systems, or other applications whose failure can be reasonably expected to result in serious
physical and/or material damage. Consult with your SANYO representative nearest you before using
any SANYO products described or contained herein in such applications.
SANYO assumes no responsibility for equipment failures that result from using products at values that
exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other
parameters) listed in products specifications of any and all SANYO products described or contained
herein.
SANYO Electric Co.,Ltd. Semiconductor Company
TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN
O0504 TS IM TB-00000440 No.8034-1/4
TN6R05
Recommend Operating Conditions at Ta=25°C
Parameter
Symbol
IC Input Voltage
Conditions
Operating Frequency
Ratings
Unit
±10 to ±25
VIN
FOSC
20 to 200
V
kHz
Package Dimensions
unit : mm
2226
4.5
10.0
3.2
16.0
7.2
3.5
2.8
13.3
0.5
2.54
1.27
6.0
(5.3)
0.7
2.54
1.27
3
12
10.3
0.9
(4.0)
2.4
(0.9)
45
1.5
3.0
6.5
1 : FB
2 : Delay
3 : Drain
4 : VIN
5 : Source
1.27
1.27
2.54
SANYO : TO-220FI5H
2.54
Block Diagram
VIN
4
Detection of Timing Signal
3
DRAIN
Sense MOS
DELAY
2
Restriction of
Drive Voltage
FB
1
Feedback and
Overload Amplifier
P.MOS
5
SOURCE
(GND)
Pin Functions
Pin No.
Symbol
Function
1
FB
Input for feedback voltage and current sense
2
DELAY
Input for timing signal
3
DRAIN
Power MOSFET Drain
4
VIN
5
SOURCE(GND)
Input for Start-up voltage and drive voltage
Power MOSFET Source (Ground)
No.8034-2/4
TN6R05
Sample Application Circuit
[Feedback control]
Snubber Circuit
VOUT
VIN(AC)
+
TN4R / 6R / 8R series
5
Start-up Resistor
4
3
+
Resonant
Capacitor
Timing Capacitor
2
Pin Definitions
1 : FB
2 : DELAY
3 : DRAIN
4 : VIN
5 : SOURCE (GND)
GND
Drive
Circuit
1
Error Detection
Input Compensation Resistor
Feedback Control Capacitor
[Semi-regulated control]
Snubber Circuit
VOUT
VIN(AC)
+
TN4R / 6R / 8R series
5
Start-up Resistor
4
3
+
Resonant
Capacitor
Timing Capacitor
2
GND
1
Drive
Circuit
Feedback
Control Capacitor
Pin Definitions
1 : FB
2 : DELAY
3 : DRAIN
4 : VIN
5 : SOURCE (GND)
Input
Compensation Resistor
+
Error Detection
No.8034-3/4
TN6R05
Forward Bias ASO
Drain Current, ID -- A
3
2
IDP=19.5A
10
7
5
ID=6.5A
1m
<10µs
10µ
s
10
0µ
s
s
10
m
DC 100 s
op ms
era
tio
n
3
2
1.0
7
5
Operation in this
area is limited by RDS(on).
3
2
0.1
7
5
3
2
Tc=25°C
Single pulse
0.01
1.0
2
3
2.0
1.5
1.0
0.5
0
5 7 10
2
3
5 7 100
2
Drain-to-Source Voltage, VDS -- V
3
5 7 1000
IT07975
0
20
40
60
80
100
120
140
Ambient Temperature, Ta -- °C
160
IT07973
PD -- Tc
45
Allowable Power Dissipation, PD -- W
PD -- Ta
2.5
Allowable Power Dissipation, PD -- W
5
40
35
30
25
20
15
10
5
0
0
20
40
60
80
100
120
Case Temperature, Tc -- °C
140
160
IT07976
Specifications of any and all SANYO products described or contained herein stipulate the performance,
characteristics, and functions of the described products in the independent state, and are not guarantees
of the performance, characteristics, and functions of the described products as mounted in the customer’s
products or equipment. To verify symptoms and states that cannot be evaluated in an independent device,
the customer should always evaluate and test devices mounted in the customer’s products or equipment.
SANYO Electric Co., Ltd. strives to supply high-quality high-reliability products. However, any and all
semiconductor products fail with some probability. It is possible that these probabilistic failures could
give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire,
or that could cause damage to other property. When designing equipment, adopt safety measures so
that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective
circuits and error prevention circuits for safe design, redundant design, and structural design.
In the event that any or all SANYO products(including technical data,services) described or
contained herein are controlled under any of applicable local export control laws and regulations,
such products must not be exported without obtaining the export license from the authorities
concerned in accordance with the above law.
No part of this publication may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording, or any information storage or retrieval system,
or otherwise, without the prior written permission of SANYO Electric Co., Ltd.
Any and all information described or contained herein are subject to change without notice due to
product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification"
for the SANYO product that you intend to use.
Information (including circuit diagrams and circuit parameters) herein is for example only ; it is not
guaranteed for volume production. SANYO believes information herein is accurate and reliable, but
no guarantees are made or implied regarding its use or any infringements of intellectual property rights
or other rights of third parties.
This catalog provides information as of October, 2004. Specifications and information herein are subject
to change without notice.
PS No.8034-4/4